KP0115ACBKG03RGBJB

Series KP Illuminated Pushbutton with Rectangular Cap & RGB LEDs KP0115ACBKG03RGBJB Dimensions in mm/inch Tactile Actuation • Single Pole • PC Terminals Part No. This Side (4.5) .177 (3.6) .142 (7.0) .276 (0.6) Typ .024 (12.7) .500 (0.76) Typ .030 (34.8) 1.370 (15.0) Sq .591 1 (7.62) .300 1a (11.43) Typ .450 (0.5) Typ .020 (0.2) Typ .008 (5.9) .232 (11.6) .457 (17.4) .685 (23.0) .906 BASE SWITCH Part Number (0.3) Typ .012 (4.0) .157 (4.3) .169 (1.9) Typ .075 (12.7) Typ .500 POLE & CIRCUIT Plunger Position ( ) = Momentary Connected Terminals Throw & Switch Schematic Pole Model Normal Down Normal Down Note: Switch terminals “1” & “1a” are actually on the switch. SP KP0115A OFF (ON) Normally Open 1-1a SPST KP0115ACBKG03RGB 1 (COM) 1a CONTACTS, TERMINALS, & RATINGS Gold Contacts Straight PC Terminals 100mA @ 12V DC ASSEMBLY & INSTALLATION INSTRUCTIONS LED Spacer Footprint (3.81) Typ .150 (4.5) .177 (1.52) .060 (1.52) .060 (8.8) .346 (13.6) .535 (3.81) .150 (8.3) .327 (12.6) .496 LED & Spacer Assembled Spacer LED (3.81) .150 (1.3) Dia Typ .051 (1.52) Typ .060 1 1a (3.81) Typ .150 LED (0.7) Dia Typ .028 (12.7) (7.62) .500 (22.86) .300 .900 (0.9) Typ .035 (12.7) .500 (1.52) Typ .060 Spacer The Switch and Rectangular Cap assembly has 3 LEDs to achieve bright and even illumination. One LED (in center of switch bottom) is an integral part of the switch; the other 2 LEDs and 2 Spacers are packaged separately. Switch 1 Solder LEDs and Spacers into PCB. 2 Solder switch into PCB making sure that the two outer LEDs and Spacers clear the bottom side opening of the cap. PCB www.nkkswitches.com 1 11/19/20 Series KP Illuminated Pushbutton with Rectangular Cap & RGB LEDs Base Switch Specifications Electrical Capacity (Resistive Load) Low Level: 100mA maximum @ 12V DC Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Travel: 200 milliohms maximum (at 20mV AC and 10mA) 100 megohms minimum @ 250V DC 1,000V AC minimum between contacts for 1 minute minimum 1,500V AC minimum between contacts & case for 1 minute minimum 1,000,000 operations minimum (at center of cap) 1,000,000 operations minimum (at center of cap) 1.9N maximum (at center of cap) Pretravel .122” (3.1mm); Overtravel .055” (1.4mm); Total Travel .177” (4.5mm) Materials & Finishes Plunger/Upper Housing: Lower Housing: Movable Contact: Stationary Contacts: Switch Terminals: Polyacetal Glass fiber reinforced PBT (UL94V-0) Stainless steel with gold plating Gold over copper alloy Brass with tin plating Environmental Data Operating Temperature Range: Humidity: –25°C through +50°C (–13°F through +122°F) 90 – 95% humidity for 240 hours @ 40°C (104°F) PCB Processing Soldering: Cleaning: Wave Soldering. Preheat temperature: 110°C @ 40 seconds; Peak temperature: 270°C @ 6 seconds; Cycles: 2 Manual Soldering. 390°C @ 4 seconds; Cycles: 2 These devices are not process sealed. Hand clean locally using alcohol based solution. Standards & Certifications Flammability Standards: UL94V-0 lower housing The KP Series pushbuttons have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy. LED SPECIFICATIONS Electrical specifications are determined at a basic temperature of 25°C. The LED circuit is isolated and requires an external power source. For best results and safe use of the LEDs, the supply voltage should be more than the LED forward voltage. In addition, an appropriately valued ballast resistor should be used. Without the ballast resistor, the LED will be damaged or destroyed. The resistor value can be calculated by using the formula shown here. R IF + Anode VF E Cathode – Red Green Common Anode (+) Blue E – VF R = Where: R = E = VF = IF = IF Resistor Value (Ohms) Source Voltage (V) Forward Voltage (V) Forward Current (A) NC NC B(-) Common Anode (+) NC NC R(-) G(-) ATTENTION RGB ELECTROSTATIC SENSITIVE DEVICES Color Red Green Blue Maximum Forward Current I FM 30mA 30mA 30mA Typical Forward Current IF 20mA 14mA 9mA *Forward Voltage VF 2.0V 2.9V 2.9V Power Peak Dissipation PD 60mW 80mW 80mW Maximum Reverse Voltage VRM 5V 5V 5V Dominant Wavelength λd 621.5nm 522.5nm 472.5nm Current Reduction Rate Above 25°C ∆ IF 0.50mA/°C Ambient Temperature Range –25°C ~ +50°C *Forward Voltage (VF) and Dominant Wavelength (λ d) are Typical Value measured by Typical Forward Current (I F). Protection from ESD is needed in handling, storage and transportation. A conductive mat or metal plate and ESD handset are required when switches are handled. ESD bag or packaging are required for storage. www.nkkswitches.com 2