KP0215ANBKG036E-2SJB

Series KP Single Color Illuminated Pushbutton General Specifications Electrical Capacity (Resistive Load) Low Level: Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Travel: Materials & Finishes Plunger/Upper Housing: Movable Contact: Switch Terminals: Environmental Data Operating Temperature Range: Humidity: Vibration: Shock: Installation Cap Installation Force: PCB Processing Soldering: Cleaning: Standards & Certifications Flammability Standards: 100mA maximum @ 12V DC 200 milliohms maximum 100 megohms minimum @ 250V DC 1,000V AC minimum between contacts for 1 minute minimum 1,500V AC minimum between contacts & case for 1 minute minimum 5,000,000 operations minimum 5,000,000 operations minimum 1.6N maximum (at center of cap) Pretravel .091” (2.3mm); Overtravel .047” (1.2mm); Total Travel .138” (3.5mm) Polyacetal Stainless steel with gold plating Brass with tin plating Lower Housing: Stationary Contacts: Glass fiber reinforced PBT (UL94V-0) Gold over copper alloy –25°C through +50°C (–13°F through +122°F) 90 – 95% humidity for 240 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 51G (500m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) 50.0N maximum downward force on actuator Wave Soldering. Preheat temperature: 110°C @ 40 seconds; Peak temperature: 270°C @ 6 seconds; Cycles: 2 Manual Soldering. 390°C @ 4 seconds; Cycles: 2 These devices are not process sealed. Hand clean locally using alcohol based solution. UL94V-0 lower housing The KP Series pushbuttons have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy. Distinctive Characteristics KP Series’ latest offering in single color super bright white, yellow or blue LEDs with 2-pin termination. Actual Size Ideal solution for a variety of control panel compositions. Shorter stroke of .138” (3.5mm). Nontactile actuation underlined with smooth, silent operation. Compact design with height of .906” (23.0mm) from PC board to top of cap (same height as programmable SmartSwitch® ). Flat, sculptured or home key square caps in two common sizes for design flexibility in various applications. Twin contacts with gold plating assure high reliability and long life of 5,000,000 operations minimum. Custom legends available. www.nkkswitches.com 1 05/02/19 Series KP Single Color Illuminated Pushbutton TYPICAL SWITCH ORDERING EXAMPLE K P 02 15A N B K G03 6B Actuation N K Pole & Circuit 15A SPST OFF G03 ( ) = Momentary Normally Open Contacts Travel & Force 02 Black Only 15.0mm Square 3 17.4mm Square Cap Types Gold Contacts and Straight PC Terminals; 100mA @ 12V DC Plunger Stroke: 3.5mm (.138”) Actuation Force: 1.6N 2 Contacts & Terminals (ON) B 11.6mm Plunger for 15.0mm & 17.4mm Caps F Flat S Sculptured T Home Key Super Bright LEDs 6B White 6E Yellow 6G Blue Cap Color JB DESCRIPTION FOR TYPICAL ORDERING EXAMPLE KP0215ANBKG036B-2SJB 11.6mm Plunger and 15.0mm Sculptured Cap Clear Lens and White Diffuser SPST OFF-Momentary ON Circuit Normally Open Contacts Straight PC Terminals 2 www.nkkswitches.com JB Cap Sizes Housing Nontactile 2 S Super Bright White LED with 2 Pins Nontactile Actuation Black Housing Gold Contacts with 100mA Rating Clear Lens & White Diffuser Series KP Single Color Illuminated Pushbutton POLE & CIRCUIT Plunger Position Connected Terminals ( ) = Momentary Pole Model SP KP0215A Throw & Switch Schematic Normal Down Normal Down Note: Switch terminals “1” & “1a” are actually marked on the switch. OFF (ON) Normally Open 1-1a SPST 1 (COM) 1a ACTUATION N PLUNGER 11.6mm Plunger for 15.0mm & 17.4mm Caps B Nontactile (11.6) .457 (6.4) .252 11.6mm Plunger has a wide neck, easily holding either the 15.0mm or the 17.4mm Caps. HOUSING K CONTACTS, TERMINALS, & RATING G03 Black Only Gold Contacts Straight PC Terminals 100mA @ 12V DC CAP TYPES & COLORS 2 15.0mm Square F S AT3084 Flat Cap T AT3079 Sculptured Cap AT3087 Home Key Cap (7.0) .276 (7.0) .276 (7.0) .276 (2.6) Dia .102 (15.0) Sq .591 3 (15.0) Sq .591 (15.0) Sq .591 17.4mm Square F S AT3085 Flat Cap T AT3080 Sculptured Cap AT3088 Home Key Cap (7.0) .276 (7.0) .276 (7.0) .276 (2.6) Dia .102 JB (17.4) Sq .685 (17.4) Sq .685 (17.4) Sq .685 Lens & Diffuser Colors Available: Clear Lens Clear/White Materials & Finishes: Lens - Polycarbonate with glossy finish Diffuser - Polycarbonate with textured finish Optional Protective Guard AT4170 available; contact factory. www.nkkswitches.com White Diffuser 3 Series KP Single Color Illuminated Pushbutton SUPER BRIGHT LED SPECIFICATIONS The electrical specifications shown are determined at a basic temperature of 25°C. LEDs are an integral part of the switch and not available separately. LED circuit is isolated and requires an external power source. ATTENTION (+) ELECTROSTATIC SENSITIVE DEVICES (-) 6B 6E 6G White Yellow Blue Maximum Forward Current I FM 30mA 30mA 30mA Typical Forward Current IF 20mA 20mA 20mA Forward Voltage VF 3.2V 3.2V 3.2V Maximum Reverse Voltage VRM 5V 5V 5V .045mA/°C If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula shown here. R + IF Anode VF E Cathode – R = Current Reduction Rate Above 30°C ∆ IF 0.45mA/°C Ambient Temperature Range –25 ~ +50°C –25 ~ +50°C –25 ~ +50°C Where: R = E = VF = IF = .045mA/°C E – VF IF Resistor Value (Ohms) Source Voltage (V) Forward Voltage (V) Forward Current (A) TYPICAL SWITCH DIMENSIONS 15.0mm Square Cap with Yellow LED (3.6) .142 (0.3) .012 (6.4) .252 Part No. This Side (0.6) Typ .024 1a 1 (4.5) (12.7) .177 .500 (7.62) .300 L2 L1 (12.7) .500 (0.5) Sq Typ .020 (15.0) Sq .591 (1.1) .043 (7.0) (4.5) (11.5) .276 .177 .453 (23.0) .906 (7.62) .300 (1.3) Dia Typ .051 (0.9) Dia Typ .035 (0.8) Dia Typ .031 1 1a L1 L2 (1.27) Typ .050 (2.54) +– 0.5 .100 (12.7) .500 (12.7) .500 (15.0) Sq .591 (6.0) .236 (4.5) .177 (12.7) .500 KP0215ANBKG036E-2SJB 17.4mm Square Cap with Blue LED (3.6) .142 (0.3) .012 (6.4) .252 Part No. This Side (0.6) Typ .024 1 1a (4.5) (12.7) .177 .500 (7.62) .300 L2 L1 (0.5) Sq Typ .020 (17.4) Sq .685 (1.1) .043 (7.0) (4.5) (11.5) .276 .177 .453 (23.0) .906 (2.54) +– 0.5 .100 (6.0) .236 KP0215ANBKG036G-3SJB 4 (12.7) .500 www.nkkswitches.com (12.7) .500 (15.0) Sq .591 (7.62) .300 (1.3) Dia Typ .051 (0.9) Dia Typ .035 (0.8) Dia Typ .031 1 1a L1 L2 (4.5) .177 (12.7) .500 (1.27) Typ .050 (12.7) .500 Series KP Single Color Illuminated Pushbutton ASSEMBLY INSTRUCTIONS FOR SQUARE CAPS Cap Orientation ATTENTION ELECTROSTATIC SENSITIVE DEVICES As shown in the accompanying illustration, the cap and plunger are designed with tabs and notches to assure proper orientation of the cap on the switch. Removal of Cap Assembly & Separation of Lens & Diffuser Notch Tab Step Plunger Notches Holding the switch tightly, pull the cap off the switch. Once the cap assembly is released from the plunger, the lens and diffuser can be separated. Pry up the lens with fingernail or flat tip screwdriver inserted at the step on the diffuser. Cap Assembly Installation or Replacement of Cap Plunger After aligning notches with tabs, join the lens and diffuser. Hold the switch tightly without touching the terminals. Firmly press the cap onto the plunger by applying pressure from one side to the other until both are snapped together. Switch LEGENDS NKK Switches can provide custom legends for caps. Contact factory for more information. Suggested Printable Areas for KP Lens Recommended Methods: Lens Laser Etch on clear lens, Screen Print, or Pad Print on lens. Laser Print on film insert. Epoxy based ink is recommended. OP ST Film Insert Diffuser Printing on Diffuser is not advisable. Shaded areas are suggested printable areas for Lens. Sculptured Cap Lens Flat Cap Lens (13.4) Sq .528 (17.4) Sq .685 (12.8) Sq .504 (15.0) Sq .591 (11.48) Dia .452 (13.0) Dia .512 (0.76) Typ .030 (13.77) Dia .542 (15.3) Dia .602 (0.76) Typ .030 Suggested Printable Areas for KP Film Insert Shaded areas are suggested printable areas for Film Insert. Sculptured Cap Film Inserts Flat Cap Film Inserts (0.5) R .020 (0.5) R .020 (11.28) Sq .444 (12.8) Sq .504 (0.76) Typ .030 (11.88) Dia .468 (13.4) Sq .528 (0.76) Typ .030 (0.5) R .020 (0.5) R .020 (11.28) Dia .444 (12.8) Sq .504 (0.76) Typ .030 (11.88) Dia .468 (13.4) Sq .528 (0.76) Typ .030 Film Insert Material and Thickness: Clear Polyester; 4 mil (100µ) maximum thickness www.nkkswitches.com 5