LB15SGW01-H

Standard Size Pushbuttons Series LB Distinctive Characteristics Square, round, rectangular, and round panel seal models available. Stainless steel clips provide secure mounting with a wide range of panel thicknesses. Latchdown feature gives indication of circuit status. Audible and tactile feedback with smooth and responsive operation. Snap-action contact mechanism gives long electrical life and sensitivity of actuation. Combination solder lug and .110” quick connect terminals are epoxy sealed to prevent entry of flux, dust, and other contaminants. Panel sealed model meets IP65 of IEC60529 specifications (similar to NEMA 4 & 13). Compact switch design minimizes behind panel depth. Matching illuminated models available and shown in the Illuminated Pushbutton section. Matching indicators available and shown at the end of Section M. Actual Size N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Standard Size Pushbuttons Series LB General Specifications Electrical Capacity (Resistive Load) Power Level (silver): Logic Level (gold): 3A @ 125V AC or 3A @ 250V AC or 3A @ 30V DC 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Note: Find additional explanation in Supplement section. Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Contact Timing: Travel: 50 milliohms maximum for silver; 100 milliohms maximum for gold 200 megohms minimum @ 500V DC 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts & case for 1 minute minimum 1,000,000 operations minimum for momentary circuit 200,000 operations minimum for maintained circuit 100,000 operations minimum 4.41N Nonshorting (break-before-make) Pretravel .059” (1.5mm); Overtravel .059” (1.5mm); Total Travel .118” (3.0mm) Pretravel .087” (2.2mm); Overtravel .031” (0.8mm); Total Travel .118” (3.0mm) Materials & Finishes Housing: Snap-in Frame: Movable Contact: Stationary Contacts: Base: Terminals: Glass fiber reinforced polyamide (UL94V-0) Stainless steel Silver alloy or copper with gold plating Silver alloy or copper with gold plating Liquid crystal polymer (UL94V-0) Phosphor bronze with silver or gold plating Environmental Data Operating Temp Range: Humidity: Vibration: Shock: Sealing: –25°C through +70°C (–13°F through +158°F) Note: When used with a polyvinyl chloride splash cover, the lowest limit is 0°C (32°F) 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Not available for snap-in; see next section for panel seal. Installation Cap Installation Force: Quick Connect Force: Soldering Time & Temperature: 3.92N maximum downward force on cap 52.95N maximum downward force on connector Manual Soldering: See Profile A in Supplement section. Standards & Certifications Flammability Standards: UL & C-UL Recognized: R CSA Certified: UL94V-0 housing & base All models recognized at 3A @ 125V or 250V AC or 0.4VA @ 28V AC/DC maximum; UL File No. WOYR2.E44145; add “/U” to end of part number to order UL mark on switch; C-UL File No. WOYR8.E44145; add “/C-UL” to end of part number to order C-UL mark on switch. All models certified at 3A @ 125V or 250V AC or 0.4VA @ 28V AC/DC maximum; CSA File Nos. 023535-0-000; add “/C” to end of part number to order CSA mark on switch. N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Standard Size Snap-in Pushbuttons TYPICAL SWITCH ORDERING EXAMPLE Series LB LB 1 5 S K W01 C P OLES 1 2 SPDT DPDT S C R SHAPES Square Round Rectangular G01 W01 CONTACTS & TERMINALS Silver Contacts Rated 3A @ 125/250V AC Solder Lug/Quick Connect Terminals Gold Contacts Rated 0.4VA @ 28V AC/DC Solder Lug/Quick Connect Terminals CIRCUITS 5 6 ON ON (ON) ON ( ) = Momentary Alternate Action with Latchdown K G H OUSING Black Gray A B C Black CAP COLORS E F Yellow Green G Blue H Gray White Red IMPORTANT: Switches are supplied without UL, C-UL & CSA markings unless specified. Specific models & ratings noted on General Specifications page. Note: Insert Cap with clear lens and colored filter available; see Illuminated Pushbuttons section DESCRIPTION FOR TYPICAL ORDERING EXAMPLE LB15SKW01-C Red Cap SPDT ON-(ON) Circuit Square Shape Silver Contacts Rated 3A @ 125/250V AC; Solder Lug/Quick Connect Terminals Black Housing N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Standard Size Snap-in Pushbuttons POLES & CIRCUITS Plunger Position ( ) = Momentary Normal Pole SP DP Model LB15 *LB16 LB25 *LB26 ON ON ON ON (ON) ON (ON) ON 1-3 1-3 4-6 1-2 1-2 4-5 Down Connected Terminals Normal Down Note: Series LB Throw & Switch/Lamp Schematics Switch is marked with NC, NO, COM, L+, L–. 1 COM 2 NO 4 NO 6 NC COM 5 NO SPDT 1 3 COM NC DPDT 3 NC 2 * When in latchdown position for the alternate circuit, cap position is .039” (1.0mm) above the built-in bezel. SHAPES & PANEL CUTOUTS S .622” (15.8mm) Square C .854” (21.7mm) Round R (22.0) Dia .866 .622” x .866” (15.8mm x 22.0mm) Rectangular (16.2) .638 (11.5) .453 (16.2) Sq .638 (1.5) R .059 (22.4) .882 Cutout for 1 switch: .638” x .638” (16.2mm x 16.2mm) Cutout for 1 switch with barriers: .638” x .815” (16.2mm x 20.7mm) Cutout for 1 switch: .638” x .882” (16.2mm x 22.4mm) Cutout for 1 switch with barriers: .638” x 1.059” (16.2mm x 26.9mm) Panel Thickness for Switches & Barriers: .039” ~ .157” (1.0 ~ 4.0mm) Panel Thickness for Protective Guards & Splash Covers: .039” ~ .138” (1.0 ~ 3.5mm) HOUSING Housing Colors Available: K Black G Gray C ONTACT MATERIALS, RATINGS & TERMINALS W01 G01 Silver Contacts Gold Contacts Power Level 3A @ 125V AC & 250V AC Logic Level 0.4VA max. @ 28V AC/DC max. Solder Lug/Quick Connect Epoxy Seal (2.0) .079 (7.5) .295 (2.8) .110 (1.2) .047 Complete explanation of operating range in Supplement section. Thk = (0.5) .020 CAPS & CAP COLORS Color Codes: Cap Colors Available: A Black AT484 Square B White C Red AT4017 Round E Yellow F Green G Blue (13.2) .520 H Gray (19.4) .764 A B C E F G H (13.2) Sq .520 (3.5) .138 (19.0) Dia .748 (4.5) .177 AT4030 Rectangular (6.5) .256 (5.5) .217 (5.0) .197 (6.0) .236 Material: Polycarbonate Finish: Glossy 03-07 N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com Standard Size Snap-in Pushbuttons T YPICAL SWITCH DIMENSIONS Square Single & Double Pole Series LB (1.8) .071 (1.2) x (2.0) Typ .047 x .079 (0.5) Typ .020 NC NO 3 2 L (+) 6 5 (13.2) Sq .520 (2.54) Typ .100 (1.0) .039 (17.8) Sq .701 (3.2) .126 (21.5) .846 Latchdown Position (7.5) .295 (15.8) Sq .622 COM 1 L (-) 4 (2.8) Typ .110 (5.08) Typ .200 LB15SKW01-C Single pole models do not have terminals 4, 5, & 6. Round Single & Double Pole (1.8) .071 (1.2) x (2.0) Typ .047 x .079 (0.5) Typ .020 L (+) NC NO 3 2 6 5 4 (15.8) Sq .622 (21.7) Dia .854 (2.54) Typ .100 (19.0) Dia .748 (23.7) Dia .933 (1.0) .039 (3.2) .126 (21.5) .846 Latchdown Position (7.5) .295 COM 1 L (-) (2.8) Typ .110 (5.08) Typ .200 LB16CKW01-C Single pole models do not have terminals 4, 5, & 6. Rectangular Single & Double Pole (1.8) .071 (1.2) x (2.0) Typ .047 x .079 (0.5) Typ .020 NC NO 3 2 L (+) 6 5 (13.2) .520 (17.8) .701 (15.8) .622 (2.54) Typ .100 (19.4) .764 (1.0) .039 (24.0) .945 (3.2) .126 (22.5) .886 Latchdown Position (7.5) .295 COM 1 L (-) 4 (5.08) Typ .200 (22.0) .866 (2.8) Typ .110 LB26RGW01-C Single pole models do not have terminals 4, 5, & 6. 03-07 N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com Standard Size Snap-in Pushbuttons O PTIONAL ACCESSORIES Barriers AT497 End End Position Series LB AT498 Center (23.5) .925 (4.3) Typ .169 (5.2) .205 (19.2) .756 Cutouts for More Than 1 Switch A (20.0) .787 (15.0) .591 (16.2) .638 Center Position Square A = .752” (19.1mm) x Number of Switches + .051” (1.3mm) (1.19) .047 (1.19) .047 (19.2) .756 Material: Polyamide Rectangular A = .996” (25.3mm) x Number of Switches + .051” (1.3mm) Protective Guard AT499 Square Protective Guard Opens 90° Closes manually (10.0) .394 (21.0) .827 (17.0) .669 Cap Height When Assembled (20.0) .787 (8.0) .315 Materials: Cover: Clear Polycarbonate Base: Black GFR Polyamide (14.0) Sq .551 (17.9) Sq .705 Protective Guards reduce depth of switch behind panel by .020” (0.5mm). Spring Loaded Protective Guard AT4171 Square Protective Guard Opens 180° Closes automatically (10.5) .413 (20.5) .807 Cap Height When Assembled (17.9) .705 (7.1) .280 (18.4) .724 (20.4) .803 (7.5) .295 (14.2) .559 (17.9) .705 (16.2) Sq .638 (39.0) Min* 1.535 AT 4171 (10.5) .413 (20.5) .807 Materials: Cover: Clear Polycarbonate Base: Black GFR Polyamide Coil Spring: Stainless Steel 180° (20.4) .803 (20.4) .803 (N) * Minimum dimension allows opening of cover to 180° (N) = Number of switches Recommended Panel Thickness: .039” ~ .106” (1.0mm ~ 2.7mm) 03-07 N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com Standard Size Snap-in Pushbuttons O PTIONAL ACCESSORIES Protective Guard AT4057 Rectangular Protective Guard Opens 90° Closes manually (10.0) .394 Series LB (14.0) .551 (21.0) .827 Cap Height When Assembled (26.0) 1.024 (8.0) .315 (24.15) .951 Materials: Cover: Clear Polycarbonate Base: Black GFR Polyamide Protective Guards reduce depth of switch behind panel by .020” (0.5mm). Spring Loaded Protective Guard AT4172 Rectangular Protective Guard Opens 180° Closes automatically (10.5) .413 (20.5) .807 Cap Height When Assembled (17.9) .705 (7.1) .280 (24.6) .969 (26.6) 1.047 (7.5) .295 (20.4) .803 (24.1) .949 Materials: Cover: Clear Polycarbonate Base: Black GFR Polyamide Coil Spring: Stainless Steel Recommended Panel Thickness: .039” ~ .106” (1.0mm ~ 2.7mm) (16.2) .638 (22.4) .882 180° AT4172 (10.5) .413 (20.5) .807 (39.0) Min* 1.535 (26.6) 1.047 (N) = Number of switches (26.6) 1.047 (N) * Minimum dimension allows opening of cover to 180° N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Standard Size Snap-in Pushbuttons OPTIONAL ACCESSORIES Dust Covers AT4002 Round AT4001 Square AT4011 Rectangular Series LB Materials: Lid: Polyvinyl chloride Gasket: Polyethylene PVC loses pliability below 0°C (32°F. (21.0) Dia .827 (21.0) Dia .827 (16.5) .650 (16.5) .650 (24.0) .945 Cap Height When Assembled (7.3) .287 (2.5) .098 (21.8) Dia .858 (30.0) Dia 1.181 Cap Height When Assembled (7.3) .287 (2.5) .098 (22.7) .894 (24.0) Sq .945 (30.2) 1.189 Dust Covers reduce depth of switch behind panel by .020” (0.5mm). PCB Adaptors AT711 Single Pole • Straight PC Terminals (0.3) Typ .012 (5.08) .200 (15.8) Sq .622 AT712 Double Pole • Straight PC Terminals (0.3) Typ .012 (5.08) Typ .200 (15.8) Sq .622 NC NO COM L L (+) (-) NC NO COM NC NO L L (+) (-) NC NO COM (2.54) Typ .100 (1.0) Dia Typ .039 (0.5) .020 (15.0) (4.0) .591 .157 (2.54) Typ .100 (0.74) Typ .029 COM (2.54) Typ .100 (1.0) Dia Typ .039 (0.5) .020 (15.0) (4.0) .591 .157 (2.54) Typ .100 (0.74) Typ .029 (5.08) .200 (5.08) .200 Note: Order adaptors separately. N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Standard Size Snap-in Pushbuttons ASSEMBLY INSTRUCTIONS Round & Rectangular Match clip on cap assembly with receptacle inside switch. N .C . Series LB Cut Corner C Projection N .C . K S 5C -1 5V A C LB 12 0V A A 3 25 A 3 C Projection Notch Square Match projection (C) on cap assembly with groove (C) inside switch. Panel Seal Bushing Mount Insert switch from the front of the panel with the o-ring between the built-in bezel and the panel. Install mounting nut AT075 (supplied with switch) from the Bezel rear of the panel. O-ring Overtightening mounting nut may damage the switch housing. N .O . Rubber Seal Panel Seal Match projection on cap assembly with notch inside switch. Snap-in Mount Snap-in clip holds all switches firmly in place. To mount round switch, match the antirotation projection on switch with guide cut in panel. Snap Projection into panel cutout. Panel AT109 Cap Extractor Panel AT112 Socket Wrench Mounting Nut LEGENDS Easily create and submit your own legends using our new on-line Legend Maker. Visit www.nkkswitches.com For other legend support options, customers may either contact the factory and request the LB Legend Packet, or utilize the general information and basic specifications presented below. Suggested Printable Area for LB Lens (0.76) Typ .030 Recommended Methods: Laser Etch on clear lens; Screen Print or Pad Print on lens. Epoxy based ink is recommended. Additional method for legends is engraving the cap. Maximum depth for engraving is .012” (0.3mm) on the cap lens. Enamel paint is recommended to fill the engraved area. N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 LM T AR ST (11.68) Sq .460 (13.2) Sq .520 (0.76) Typ .030 (17.48) Dia .688 (19.0) Dia .748 (0.76) Typ .030 (17.88) .704 (19.4) .764 (11.68) .460 (13.2) .520 (0.76) Typ .030 Shaded areas are printable areas. Additional Method