LB25WGG01-BJ

Standard Size Panel Seal Pushbuttons Series LB Distinctive Characteristics Square, round, rectangular, and round panel seal models available. Stainless steel clips provide secure mounting with a wide range of panel thicknesses. Latchdown feature gives indication of circuit status. Audible and tactile feedback with smooth and responsive operation. Snap-action contact mechanism gives long electrical life and sensitivity of actuation. Combination solder lug and .110” quick connect terminals are epoxy sealed to prevent entry of flux, dust, and other contaminants. Panel sealed model meets IP65 of IEC60529 specifications (similar to NEMA 4 & 13). Compact switch design minimizes behind panel depth. Matching illuminated models available and shown in the Illuminated Pushbutton section. Matching indicators available and shown at the end of Section M. Actual Size N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Standard Size Panel Seal Pushbuttons Series LB General Specifications Electrical Capacity (Resistive Load) Power Level (silver): Logic Level (gold): 3A @ 125V AC or 3A @ 250V AC 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Note: Find additional explanation of operating range in Supplement section. Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Contact Timing: Travel: 50 milliohms maximum for silver; 100 milliohms maximum for gold 200 megohms minimum @ 500V DC 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts & case for 1 minute minimum 1,000,000 operations minimum for momentary circuit 200,000 operations minimum for maintained circuit 100,000 operations minimum 5.39N Nonshorting (break-before-make) Momentary: Pretravel .059” (1.5mm); Overtravel .059” (1.5mm); Total Travel .118” (3.0mm) Maintained: Pretravel .087” (2.2mm); Overtravel .031” (0.8mm); Total Travel .118” (3.0mm) Materials & Finishes Housing: O-ring: Inner Seal: Movable Contact: Stationary Contacts: Base: Terminals: Glass fiber reinforced polyamide (UL94V-0) Nitrile butadiene rubber Silicone rubber Silver alloy or copper with gold plating Silver alloy or copper with gold plating Liquid crystal polymer (UL94V-0) Phosphor bronze with silver or gold plating Environmental Data Operating Temp Range: Humidity: Vibration: Shock: Sealing: –25°C through +70°C (–13°F through +158°F) Note: When used with a polyvinyl chloride splash cover, the lowest limit is 0°C (32°F) 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) IP65 of IEC60529 standard (similar to NEMA 4 & 13) Installation Mounting Torque: Cap Installation Force: Quick Connect Force: Soldering Time & Temperature: 1.96Nm (17.35 lb•in) maximum 3.92N maximum downward force on cap 52.95N maximum downward force on connector Manual Soldering: See Profile A in Supplement section. Standards & Certifications Flammability Standards: UL & C-UL Recognized: R CSA Certified: UL94V-0 housing & base All models recognized at 3A @ 125V or 250V AC or 0.4VA @ 28V AC/DC maximum; UL File No. WOYR2.E44145; add “/U” to end of part number to order UL mark on switch; C-UL File No. WOYR8.E44145; add “/C-UL” to end of part number to order C-UL mark on switch. All models certified at 3A @ 125V or 250V AC or 0.4VA @ 28V AC/DC maximum; CSA File Nos. 023535-0-000; add “/C” to end of part number to order CSA mark on switch. N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Standard Size Panel Seal Pushbuttons TYPICAL SWITCH ORDERING EXAMPLE Series LB CJ LB POLES 1 2 SPDT DPDT 1 6 SHAPE W Round W K W01 CONTACTS & TERMINALS W01 Silver Contacts Rated 3A @ 125/250V AC and Solder Lug/Quick Connect Terminals Gold Contacts Rated 0.4VA @ 28V AC/DC and Solder Lug/Quick Connect Terminals G01 CIRCUITS 5 6 ON ON (ON) ON ( ) = Momentary Alternate Action with Latchdown K G H OUSING Black Gray BJ CJ EJ FJ GJ CAP COLORS White Red Yellow Green Blue IMPORTANT: Switches are supplied without UL, C-UL & CSA markings unless specified. Specific models & ratings noted on General Specifications page. Note: Insert Cap with clear lens and colored filter available; see Illuminated Pushbuttons section DESCRIPTION FOR TYPICAL ORDERING EXAMPLE LB16WKW01-CJ Red Cap Round Shape Black Housing SPDT ON-ON Circuit Silver Contacts Rated 3A @ 125/250V AC; Solder Lug/Quick Connect Terminals N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Standard Size Panel Seal Pushbuttons POLES & CIRCUITS Plunger Position ( ) = Momentary Normal Pole SP DP Model LB15 *LB16 LB25 *LB26 ON ON ON ON (ON) ON (ON) ON 1-3 1-3 4-6 1-2 1-2 4-5 Down Connected Terminals Normal Down Note: Series LB Throw & Switch/Lamp Schematics Switch is marked with NC, NO, COM, L+, L–. 1 COM L (+) 3 1 COM NO 6 NC 2 NO 4 NC COM L (+) 3 NC 2 5 NO (-) L (-) L SPDT DPDT * When in latchdown position for the alternate circuit, cap position is .039” (1.0mm) above the built-in bezel. SHAPE & PANEL CUTOUT W .866” (22.0mm) Round (1.7) .067 (10.5) .413 Recommended Panel Thickness: .039” ~ .157” (1 ~ 4mm) Recommended Panel Thickness with Splash Cover: .039” ~ .138” (1 ~ 3.5mm) Overtightening the mounting nut AT074 may damage the switch housing. (22.0) Dia .866 HOUSING Housing Colors Available: K Black G Gray CONTACT MATERIALS, RATINGS & TERMINALS W01 G01 Silver Contacts Gold Contacts Power Level 3A @ 125V AC & 250V AC Logic Level 0.4VA max. @ 28V AC/DC max. Solder Lug/Quick Connect Epoxy Seal (2.0) .079 (7.5) .295 (2.8) .110 (1.2) .047 Thk = (0.5) .020 Complete explanation of operating range in Supplement section. CAP COLORS Lens/Filter Colors Available: (19.0) Dia .748 BJ CJ White Red EJ FJ Yellow Green GJ Blue AT4054 (5.1) .201 Material: Polycarbonate Finish: Glossy 03-07 N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com Standard Size Panel Seal Pushbuttons TYPICAL SWITCH DIMENSIONS Panel Seal Single & Double Pole (5.5) .217 M22 P1 (1.2) x (2.0) Typ .047 x .079 (0.5) Typ .020 NC NO Series LB 3 2 L (+) 6 5 4 (15.8) Sq .622 COM (2.54) Typ .100 (1.8) .071 (1.0) .039 (3.2) .126 1 L (-) Keyway (12.0) .472 (21.5) .846 Latchdown Position (7.5) .295 (2.8) Typ .110 (19.0) Dia .748 (25.0) Dia .984 (5.08) Typ .200 LB25WKW01-CJ Single pole models do not have terminals 4, 5, & 6. O PTIONAL ACCESSORIES PCB Adaptors AT711 Single Pole • Straight PC Terminals (0.3) Typ .012 NC NO COM L L (+) (-) NC NO COM AT712 (5.08) .200 Double Pole • Straight PC Terminals (0.3) Typ .012 NC NO L L (+) (-) NC NO COM (5.08) Typ .200 (15.8) Sq .622 (15.8) Sq .622 (2.54) Typ .100 (1.0) Dia Typ .039 (0.5) .020 (15.0) (4.0) .591 .157 (2.54) Typ .100 (0.74) Typ .029 COM (2.54) Typ .100 (1.0) Dia Typ .039 (0.5) .020 (15.0) (4.0) .591 .157 (2.54) Typ .100 (0.74) Typ .029 (5.08) .200 (5.08) .200 Note: Order adaptors separately. AT9410 Splash Cover for Panel Seal Lid Materials: Lid: Polyvinyl chloride (PVC loses pliability below 0°C/32°F) Base: Polyethylene O-ring: NBR Recommended Panel Thickness: .039” ~ .138” (1.0mm ~ 3.5mm) Base O-ring Supplied with Panel Seal Switch O-ring Supplied with AT9410 Splash Cover (21.0) Dia .827 (10.6) .417 (31.3) Dia 1.232 (7.8) .307 (3.0) .118 (1.6) .063 (23.0) Dia .906 (22.0) Dia .866 (31.3) Dia 1.232 (0.5) .020 N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Standard Size Pushbuttons ASSEMBLY INSTRUCTIONS Round & Rectangular Match clip on cap assembly with receptacle inside switch. N .C . Series LB Cut Corner C Projection N .C . K S 5C -1 5V A C LB 12 0V A A 3 25 A 3 C Projection Notch Square Match projection (C) on cap assembly with groove (C) inside switch. Panel Seal Bushing Mount Insert switch from the front of the panel with the o-ring between the built-in bezel and the panel. Install mounting nut AT075 (supplied with switch) from the Bezel rear of the panel. O-ring Overtightening mounting nut may damage the switch housing. N .O . Rubber Seal Panel Seal Match projection on cap assembly with notch inside switch. Snap-in Mount Snap-in clip holds all switches firmly in place. To mount round switch, match the antirotation projection on switch with guide cut in panel. Snap Projection into panel cutout. Panel AT109 Cap Extractor Panel AT112 Socket Wrench Mounting Nut LEGENDS Easily create and submit your own legends using our new on-line Legend Maker. Visit www.nkkswitches.com For other legend support options, customers may either contact the factory and request the LB Legend Packet, or utilize the general information and basic specifications presented below. Suggested Printable Area for LB Lens (0.76) Typ .030 Recommended Methods: Laser Etch on clear lens; Screen Print or Pad Print on lens. Epoxy based ink is recommended. Additional method for legends is engraving the cap. Maximum depth for engraving is .012” (0.3mm) on the cap lens. Enamel paint is recommended to fill the engraved area. N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 LM T AR ST (11.68) Sq .460 (13.2) Sq .520 (0.76) Typ .030 (17.48) Dia .688 (19.0) Dia .748 (0.76) Typ .030 (17.88) .704 (19.4) .764 (11.68) .460 (13.2) .520 (0.76) Typ .030 Shaded areas are printable areas. Additional Method