LB26SGG01-12-BJ

Series LB Toggles Standard Size Pushbuttons Rockers General Specifications Electrical Capacity (Resistive Load) Power Level (silver): Logic Level (gold): 3A @ 125V AC or 3A @ 250V AC or 3A @ 30V DC 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Note: Find additional explanation of operating range in Supplement section. Pushbuttons Programmable Illuminated PB Other Ratings D Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Keylocks Electrical Life: Nominal Operating Force: Contact Timing: Travel: 50 milliohms maximum for silver; 100 milliohms maximum for gold 200 megohms minimum @ 500V DC 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts & case for 1 minute minimum 1,000,000 operations minimum for momentary circuit 200,000 operations minimum for maintained circuit 100,000 operations minimum 4.41N Nonshorting (break-before-make) Pretravel .059” (1.5mm); Overtravel .059” (1.5mm); Total Travel .118” (3.0mm) Materials & Finishes Slides Housing: Snap-in Frame: Movable Contact: Stationary Contacts: Base: Switch Terminals: Lamp Terminals: Glass fiber reinforced polyamide (UL94V-0) Stainless steel Silver alloy or copper with gold plating Silver alloy or copper with gold plating Liquid crystal polymer (UL94V-0) Phosphor bronze with silver or gold plating Brass with silver plating Rotaries Environmental Data Tactiles Operating Temperature Range: Humidity: Vibration: Shock: Sealing: –25°C through +50°C (–13°F through +122°F) for Illuminated –25°C through +70°C (–13°F through +158°F) for Nonilluminated Note: When used with a polyvinyl chloride splash cover, the lowest limit is 0°C (32°F) 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Not available for snap-in; see next section for panel seal. Tilt Touch Installation Cap Installation Force: Quick Connect Force: Soldering Time & Temperature: 3.92N maximum downward force on cap 52.95N maximum downward force on connector Manual Soldering: See Profile A in Supplement section. Indicators Standards & Certifications Flammability Standards: UL: CSA: Supplement UL94V-0 housing & base File No. E44145 All models recognized at 3A @ 125V or 250V AC or 0.4VA @ 28V AC/DC maximum. Add “/U” to end of part number to order UL mark on switch. Add “/CUL” to end of part number to order cULus mark on switch. File Nos. 023535_0_000 All models certified at 3A @ 125V or 250V AC or 0.4VA @ 28V AC/DC maximum. Add “/C” to end of part number to order CSA mark on switch. Accessories D46 www.nkk.com Standard Size Pushbuttons Series LB Toggles Spot illumination available in single and bicolor LEDs. Choice of super bright LEDs in white, green, and blue in addition to standard or bright red, amber, and green LEDs. Stainless steel clips provide secure mounting with a wide range of panel thicknesses. Latchdown feature gives indication of circuit status. Audible and tactile feedback with smooth and responsive operation. Snap-action contact mechanism gives long electrical life and sensitivity of actuation. Combination solder lug and .110” quick connect terminals are epoxy sealed to prevent entry of flux, dust, and other contaminants. Panel sealed model meets IP65 of IEC60529 specifications (similar to NEMA 4 & 13). Compact switch design minimizes behind panel depth. Matching indicators available. D Actual Size Snap-in Mount Page D46 www.nkk.com D47 Supplement Panel Seal Page D57 Accessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Carefully designed light diffusion and filtering system produces bright, full surface illumination with front panel relamping. Rockers Distinctive Characteristics Series LB Toggles Standard Size Snap-in Pushbuttons TYPICAL SWITCH ORDERING EXAMPLE Toggles Rockers Pushbuttons P oles 1 SPDT DPDT 6 5 2 Circuits ON ON (ON) ON S C R ( ) = Momentary Alternate Action with Latchdown Shapes Square Round Rectangular K G Housing Black Gray Incandescent Lamp Used with Solid Cap 05 12 No Code 5-volt 12-volt Nonilluminated BJ CJ EJ FJ GJ Solid Cap: Lens/Filter Colors White/Clear Red/Clear Yellow/Clear Green/Clear Blue/Clear Insert Cap: Lens/Filter Colors JB JC JE *JF *JG Clear/White Clear/Red Clear/Yellow Clear/Green *JF & JG not suitable with neon. Clear/Blue Programmable Illuminated PB D D Contacts & Terminals W01 Silver Contacts Rated 3A @ 125/250V AC Solder Lug/Quick Connect Terminals* Gold Contacts Rated 0.4VA @ 28V AC/DC Solder Lug/Quick Connect Terminals* Incandescent or Neon Used with Insert Cap 01 05 12 No Code 110-volt Neon 5-volt Incandescent 12-volt Incandescent Nonilluminated Keylocks G01 IMPORTANT: Rotaries Switches are supplied without UL, cULus, & CSA markings unless specified. Specific models & ratings noted on General Specifications page. * Wire harness & cable assemblies offered only in Americas 5C 5D 5F DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Bright LED Used with LED Cap Colors Red Amber Green 05 12 24 Resistor No Code No Resistor 5-volt 12-volt 24-volt JB JC JD JF LED Cap: Lens/Diffuser Colors Clear/Red Clear/Amber Tactiles Slides Slides Clear/White Tactiles Clear/Green Tilt 6F 6G Red, 12-volt, Bright LED with Resistor Touch Green Blue LED in Spot Illuminated Cap Spot Illuminated Cap Colors A B C F Black Red Green Nonilluminated Cap Colors A B C E Black White Red Yellow D49 Indicators Supplement Accessories Touch Clear Cap with Red Diffuser 1C 1D Square Shape Black Housing 1F CF Red Single Color Amber Single Color Green Single Color Red/Green Bicolor Nonilluminated Indicators SPDT ON-(ON) Circuit Silver Contacts Rated 3A @ 125/250V AC; Solder Lug/Quick Connect Terminals White Available in Square and Round only. Accessories No Code Nonilluminated F G H Green Blue Gray Supplement D48 www.nkk.com w ww.nkk.com Tilt LB15SKW01-5C12-JC Super Bright LED Used with LED Cap 6B White JB LED Cap: Lens/Diffuser Colors Clear/White Rotaries Keylocks Programmable Illuminated PB Pushbuttons Lamps Cap Types & Colors Rockers LB 1 5 S K W01 5C 12 JC Series LB Toggles Standard Size Snap-in Pushbuttons P OLES & CIRCUITS Plunger Position ( ) = Momentary Rockers Connected Terminals Normal Down Throw & Switch/Lamp Schematics Notes: Switch is marked with NC, NO, COM, L+, L–. Lamp circuit is isolated and requires an external power source. 1 COM L (+) 3 1 COM NO 6 NC 2 NO 4 NC COM L (+) 3 NC 2 5 NO (-) L (-) L Pole Model LB15 *LB16 LB25 *LB26 Normal Down Pushbuttons SP ON ON ON ON (ON) ON (ON) ON 1-3 1-2 SPDT Programmable Illuminated PB DP 1-3 4-6 1-2 4-5 DPDT D * When in latchdown position for the alternate circuit, cap position is .039” (1.0mm) above the built-in bezel. SHAPES & PANEL CUTOUTS S .622” (15.8mm) Square C .854” (21.7mm) Round R (22.0) Dia .866 .622” x .866” (15.8mm x 22.0mm) Rectangular Keylocks (16.2) .638 (11.5) .453 (16.2) Sq .638 (1.5) R .059 (22.4) .882 Rotaries Slides Cutout for 1 switch: .638” x .638” (16.2mm x 16.2mm) Cutout for 1 switch with barriers: .638” x .815” (16.2mm x 20.7mm) Cutout for 1 switch: .638” x .882” (16.2mm x 22.4mm) Cutout for 1 switch with barriers: .638” x 1.059” (16.2mm x 26.9mm) Panel Thickness for Switches & Barriers: .039” ~ .157” (1.0 ~ 4.0mm) Panel Thickness for Protective Guards & Splash Covers: .039” ~ .138” (1.0 ~ 3.5mm) Tactiles HOUSING Housing Colors Available: K Black G Gray C ONTACT MATERIALS, RATINGS & TERMINALS W01 Silver Contacts Gold Contacts Power Level 3A @ 125V AC & 250V AC Logic Level 0.4VA max. @ 28V AC/DC max. Solder Lug/Quick Connect Optional PCB adaptors (2.0) AT711 & AT712 available; .079 illustrated in “Optional Accessories” immediately following “Typical Switch Dimensions.” Epoxy Seal (7.5) .295 (2.8) .110 (1.2) .047 Touch Tilt G01 Thk = (0.5) .020 Indicators Complete explanation of operating range in Supplement section. INCANDESCENT & NEON LAMP CODES & SPECIFICATIONS AT607 & AT607N AT607 Incandescent 5-volt or 12-volt; AT607N Neon 110-volt Accessories 05 V I 5V AC 115mA 12 12V AC 60mA 01 * 110V AC 1.5mA 10,000 Voltage Current Endurance T-1 Bi-pin The electrical specifications shown are determined at a basic temperature of 25°C. Lamp circuit is isolated and requires external power source. Supplement Avg. Hours 10,000 –25°C ~ +50°C www.nkk.com * Recommended Resistors for Neon: 33K ohms for 110V AC; 100K ohms for 220V AC Ambient Temp. Range D50 Standard Size Snap-in Pushbuttons LED COLORS & SPECIFICATIONS Series LB Toggles The electrical specifications shown are determined at a basic temperature of 25°C. LED circuit is isolated and requires external power source. Polarity marks are on the switch. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement section. Additional lamp detail is shown in the Accessories & Hardware section. Bright LED without Resistor AT635 LEDs are colored in OFF state. Color Codes Red Amber Green Forward Peak Current Continuous Forward Current Forward Voltage Reverse Peak Voltage IFM IF VF VRM ∆IF 30mA 20mA 1.9V 5V 30mA 20mA 2.0V 5V 0.42mA/°C –25° ~ +50°C 30mA 20mA 2.1V 5V D (+) (-) Current Reduction Rate Above 25°C Ambient Temperature Range Bright LED with Resistor T-1 ⁄ Bi-pin 12 AT627 with Resistor Red Color Codes: Amber Green Resistor Codes Forward Peak Current Continuous Forward Current Forward Voltage Reverse Peak Voltage Current Reduction Rate Above 25°C T-1 Bi-pin IFM IF VF VRM ∆IF — 52mA 5V 4V — 26mA 12V 8V 0.50mA/°C –25° ~ +50°C — 13mA 16V 24V Super Bright Single Element LED AT625G Blue AT631B White AT632F Green ELECTROSTATIC SENSITIVE DEVICES ATTENTION 6B Color White 30mA 20mA 3.6V 5V IFM IF VF VRM ∆IF 6F Green 30mA 20mA 3.5V 5V 0.50mA/°C –25° ~ +50°C 6G Blue 20mA 3.6V 5V 30mA Continuous Forward Current Forward Voltage Reverse Peak Voltage (+) (-) Current Reduction Rate Above 25°C Ambient Temperature Range T-1 Bi-pin No Code No Lamp www.nkk.com D51 Supplement Accessories Indicators Forward Peak Current Touch Tilt AT627 5-volt 4-element (+) with Resistor (-) AT627 12-volt 4-element with Resistor (+) (-) AT627 24-volt (+) 4-element with Resistor (-) Tactiles Ambient Temperature Range Slides Rotaries 5C 5D 5F 05 12 24 Keylocks Programmable Illuminated PB 5C 5D 5F No Code Red No Resistor Green Amber Pushbuttons Rockers Series LB Toggles Standard Size Snap-in Pushbuttons CAP TYPES & COLOR COMBINATIONS Color Codes: Rockers B White C Red D Amber E Yellow F Green G Blue J Clear Solid Cap for Incandescent Lamp & Nonilluminated Lens/Filter Colors Available: AT476 Square (13.2) Sq .520 (3.5) .138 (19.0) Dia .748 AT4012 Round (4.5) .177 (5.5) .217 (13.2) .520 AT4026 Rectangular (19.4) .764 (5.0) .197 (6.0) .236 Pushbuttons Translucent Colored Lens BJ CJ FJ GJ (6.5) .256 Programmable Illuminated PB Transparent Clear Filter D EJ Material: Polycarbonate Finish: Glossy Lamp AT607 Insert Cap for Incandescent or Neon Lamp & Nonilluminated Lens/Filter Colors Available: AT477 Square (13.2) Sq .520 (3.5) .138 (19.0) Dia .748 AT4013 Round (4.5) .177 (5.5) .217 (13.2) .520 AT4027 Rectangular (19.4) .764 (5.0) .197 (6.0) .236 Keylocks JB JC JF JG Transparent Clear Lens Rotaries (6.5) .256 Translucent Colored Filter JE JF and JG not suitable with neon lamp. Material: Polycarbonate Finish: Glossy Lamp AT607 or 607N Slides Cap for Bright LED without Resistor Lens/Diffuser Colors Available: AT4176 Square (3.5) .138 (6.5) .256 Tactiles AT4178 Round (19.0) Dia .748 (4.5) .177 (13.2) .520 AT4177 Rectangular (19.4) .764 (5.0) .197 (5.5) .217 (6.0) .236 JB JC (13.2) Sq .520 Transparent Clear Lens Tilt JD JF Translucent Colored Diffuser Bright LED AT635 Touch Material: Polycarbonate Finish: Glossy Cap for Bright LED with Resistor Indicators Lens/Diffuser Colors Available: AT4162 Square (3.5) .138 (19.0) Dia .748 AT4164 Round (4.5) .177 (13.2) .520 AT4163 Rectangular Transparent Clear Lens (19.4) .764 (5.0) .197 (6.0) .236 JB JC JD JF Accessories (13.2) Sq .520 (6.5) .256 (5.5) .217 Translucent Colored Diffuser Bright LED AT627 Supplement Material: Polycarbonate D52 www.nkk.com Finish: Glossy Standard Size Snap-in Pushbuttons CAP TYPES & COLOR COMBINATIONS Color Codes: A Black B White C Red D Amber E Yellow F Green G Blue Series LB H Gray J Clear Rockers Toggles Cap for Super Bright LEDs JB Clear Lens White Diffuser (13.2) Sq .520 AT4129 Square (3.5) .138 (19.0) Dia .748 AT4128 Round (4.5) .177 (5.5) .217 (13.2) .520 AT4130 Rectangular (19.4) .764 (5.0) .197 (6.0) .236 Transparent Clear Lens Translucent White Diffuser LEDs AT625 AT631 AT632 (6.5) .256 Spot Illuminated Cap with LED The electrical specifications shown are determined at a basic temperature of 25°C. LED circuit is isolated and requires an external power source. Single color LEDs are colored in OFF state; bicolor LEDs are translucent white in OFF state. Polarity marks are on the switch. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement section. Additional lamp detail is shown in the Accessories & Hardware section. LED Specifications Single Color LED with 1 Element LED factory assembled in Spot Illuminated Caps Not Available Separately (+) (-) (+) D Bicolor LED with 2 Elements (-) Single Color Bicolor 1C Red 10mA 8mA 1.9V 5V 1D Amber 30mA 24mA 2.0V 5V 1F Green 30mA 24mA 2.1V 5V 0.40mA/°C –25° ~ +50°C CF 30/25mA 20mA — 0.43/0.38mA/°C Tactiles Slides Rotaries Supplement Accessories Indicators Touch Tilt Red/Green Forward Peak Current Continuous Forward Current Forward Voltage Reverse Peak Voltage Current Reduction Rate Above 25°C Ambient Temperature Range IFM IF VF VRM ∆IF 2.0/2.2V 0.13mA/°C 0.40mA/°C Cap Colors Available: A B C F (13.2) Sq .520 (4.0) .157 (2.0) .079 (5.0) .197 AT480 Square (3.5) .138 (19.0) Dia .748 (5.0) .197 AT4016 Round (4.5) .177 (5.5) .217 Cap with Window Material: Polycarbonate Finish: Glossy (6.5) .256 (2.0) (6.0) .079 .236 Factory Assembled LED; Not Available Separately When ordering spot illuminated cap separately, LED color must be specified. Examples: AT480CA (red LED, black cap); AT4016CFB (red/green bicolored LED, white cap) Cap Colors Available: Cap for Nonilluminated AT484 Square AT4017 Round (3.5) .138 (19.0) Dia .748 (4.5) .177 (13.2) .520 AT4030 Rectangular (19.4) .764 A B C E F G H (13.2) Sq .520 (6.5) .256 (5.5) .217 (5.0) .197 (6.0) .236 Cap No Lamp Material: Polycarbonate Finish: Glossy www.nkk.com D53 Keylocks Programmable Illuminated PB Pushbuttons Material: Polycarbonate Finish: Glossy Series LB Toggles Standard Size Snap-in Pushbuttons TYPICAL SWITCH DIMENSIONS Square Rockers Single & Double Pole (1.8) .071 (1.2) x (2.0) Typ .047 x .079 (0.5) Typ .020 (13.2) Sq .520 (2.54) Typ .100 (1.0) .039 NC NO 3 2 L (+) 6 5 Pushbuttons (15.8) Sq .622 COM 1 L (-) 4 Programmable Illuminated PB D LB15SKW01-12-CJ (17.8) Sq .701 (3.2) .126 (21.5) .846 Latchdown Position (7.5) .295 (2.8) Typ .110 (5.08) Typ .200 Single pole models do not have terminals 4, 5, & 6. Round Single & Double Pole (1.8) .071 (1.2) x (2.0) Typ .047 x .079 (0.5) Typ .020 L (+) NC NO 3 2 6 5 4 Keylocks (15.8) Sq .622 (21.7) Dia .854 (2.54) Typ .100 (19.0) Dia .748 (23.7) Dia .933 (1.0) .039 (3.2) .126 (21.5) .846 Latchdown Position (7.5) .295 COM 1 L (-) Rotaries (2.8) Typ .110 (5.08) Typ .200 LB16CKW01-12-CJ Slides Single pole models do not have terminals 4, 5, & 6. Rectangular Single & Double Pole (1.8) .071 (1.2) x (2.0) Typ .047 x .079 (0.5) Typ .020 NC NO 3 2 L (+) 6 5 Tactiles (13.2) .520 (17.8) .701 (15.8) .622 (2.54) Typ .100 COM 1 L (-) 4 Tilt (19.4) .764 (1.0) .039 (24.0) .945 (3.2) .126 (22.5) .886 Latchdown Position (7.5) .295 (5.08) Typ .200 (22.0) .866 (2.8) Typ .110 Touch LB26RGW01-12-CJ Single pole models do not have terminals 4, 5, & 6. OPTIONAL ACCESSORIES Indicators PCB Adaptors AT711 Single Pole • Straight PC Terminals (0.3) Typ .012 NC NO COM L L (+) (-) NC NO COM AT712 (5.08) .200 Double Pole • Straight PC Terminals (0.3) Typ .012 NC NO L L (+) (-) NC NO COM Accessories (5.08) Typ .200 (15.8) Sq .622 (15.8) Sq .622 (2.54) Typ .100 (1.0) Dia Typ .039 (0.5) .020 (15.0) (4.0) .591 .157 (2.54) Typ .100 (0.74) Typ .029 COM (2.54) Typ .100 (1.0) Dia Typ .039 Supplement (0.5) .020 (15.0) (4.0) .591 .157 (2.54) Typ .100 (0.74) Typ .029 (5.08) .200 (5.08) .200 Note: Order adaptors separately. D54 www.nkk.com Standard Size Snap-in Pushbuttons OPTIONAL ACCESSORIES Barriers (23.5) .925 (4.3) Typ .169 (5.2) .205 Series LB Toggles Cutouts for More Than 1 Switch (19.2) .756 A End Position (20.0) .787 (15.0) .591 (16.2) .638 Center Position Material: Polyamide (1.19) .047 (1.19) .047 (19.2) .756 Square A = .752” (19.1mm) x Number of Switches + .051” (1.3mm) Rectangular A = .996” (25.3mm) x Number of Switches + .051” (1.3mm) D Protective Guard AT499 Square Protective Guard Opens 90° Closes manually (10.0) .394 (21.0) .827 (17.0) .669 Cap Height When Assembled (20.0) .787 (8.0) .315 (14.0) Sq .551 (17.9) Sq .705 Material: Polyamide Protective Guards reduce depth of switch behind panel by .020” (0.5mm). Spring Loaded Protective Guard AT4171 Square Protective Guard Opens 180° Closes automatically (10.5) .413 (20.5) .807 Cap Height When Assembled (17.9) .705 (7.1) .280 (18.4) .724 (16.2) Sq .638 (39.0) Min* 1.535 AT4171 (10.5) .413 (20.5) .807 (20.4) .803 (20.4) .803 (N) * Minimum dimension allows opening of cover to 180° (N) = Number of switches Recommended Panel Thickness: .039” ~ .106” (1.0mm ~ 2.7mm) www.nkk.com D55 Supplement Accessories Materials: Cover: Clear Polycarbonate Base: Black GFR Polyamide Coil Spring: Stainless Steel 180° Indicators Touch (20.4) .803 (7.5) .295 (14.2) .559 (17.9) .705 Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers AT497 End AT498 Center Series LB Toggles Standard Size Snap-in Pushbuttons O PTIONAL ACCESSORIES Protective Guard AT4057 Rectangular Protective Guard Opens 90° Closes manually (26.0) 1.024 Rockers (10.0) .394 Pushbuttons (14.0) .551 (21.0) .827 Cap Height When Assembled (8.0) .315 (24.15) .951 Programmable Illuminated PB D Material: Polyamide Protective Guards reduce depth of switch behind panel by .020” (0.5mm). Spring Loaded Protective Guard AT4172 Rectangular Protective Guard (10.5) .413 (20.5) .807 Cap Height When Assembled (17.9) .705 (7.1) .280 Keylocks (22.4) .882 Rotaries (16.2) .638 (24.6) .969 (26.6) 1.047 (7.5) .295 (20.4) .803 (24.1) .949 AT4172 (10.5) .413 (20.5) .807 (39.0) Min* 1.535 Opens 180° Closes automatically Materials: Cover: Clear Polycarbonate Base: Black GFR Polyamide Coil Spring: Stainless Steel 180° Slides Tactiles (26.6) 1.047 (N) = Number of switches (26.6) 1.047 (N) * Minimum dimension allows opening of cover to 180° Recommended Panel Thickness: .039” ~ .106” (1.0mm ~ 2.7mm) Dust Covers Tilt AT4002 Round Touch AT4001 Square AT4011 Rectangular Indicators (21.0) Dia .827 (15.0) Sq .591 (16.5) .650 (16.5) .650 (24.0) .945 Accessories Supplement Cap Height When Assembled (7.3) .287 Cap Height When Assembled (2.5) .098 (21.8) Dia .858 (30.0) Dia 1.181 (7.3) .287 (2.5) .098 (24.0) Sq .945 (22.7) .894 (30.2) 1.189 Materials: PVC with polyethylene gasket; PVC loses pliability below 0°C (32°F). Dust Covers reduce depth of switch behind panel by .020” (0.5mm). D56 www.nkk.com