Series LP01
Toggles
Short Body Pushbuttons
Rockers
General Specifications
Electrical Capacity (Resistive Load)
Power Level (silver): 3A @ 125V AC or 3A @ 250V AC or 3A @ 30V DC
Pushbuttons
Other Ratings
Programmable Illuminated PB
D
Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life:
Nominal Operating Force: Contact Timing: Travel:
50 milliohms maximum 200 megohms minimum @ 500V DC 1,000V AC minimum between contacts for 1 minute minimum 1,500V AC minimum between contacts and case for 1 minute minimum 500,000 operations minimum 50,000 operations minimum for 3A @ 125V/250V AC & 3A @ 30V DC 100,000 operations minimum for 1A @ 125V/250V AC & 1A @ 30V DC 1.5N for Single Pole; 3.0N for Double Pole Nonshorting (break-before-make) Total Travel .118” (3.0mm)
Keylocks
Materials & Finishes
Actuator: Housing:
Base: Movable Contact: Stationary Contacts: Lamp Terminals:
Slides
Polycarbonate Bushing mount: Glass fiber reinforced polyamide (UL94V-0); Snap in mount: Polyphenylene ether (UL94V-0) Diallyl phthalate (UL94V-0) Phosphor bronze & silver with silver plating Common terminal: Phosphor bronze with silver plating; Contact terminals: Phosphor bronze with tin & copper plating Phospher bronze with tin and copper plating
Rotaries
Environmental Data
Tactiles
Operating Temperature Range: Humidity: Vibration: Shock:
Tilt
–10°C through +50°C (+14°F through +122°F) for Illuminated –25°C through +70°C (+13°F through +158°F) for Nonilluminated 90 ~ 95% humidity for 240 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Installation
Touch
Mounting Torque: Soldering Time & Temperature: Cleaning:
0.8Nm (7.08 lb • in) Manual Soldering: See Profile A in Supplement section. Hand clean locally with alcohol based solution
Indicators
Standards & Certifications
Flammability Standards: UL:
Supplement
Accessories
UL94V-0 housing & base File No. E44145 All single & double pole models recognized at 3A @ 125V/250V AC or 3A @ 30V DC. Add “/U” to end of part number to order UL mark on switch. Add “/CUL” to end of part number to order cULus mark on switch.
D66
www.nkk.com
Short Body Pushbuttons
Series LP01
Toggles
Smooth, slightly concave surface of cap designed to fit fingertip. Unique design and construction of cap prevents its removal and limits tampering.
D
Bright LED illumination in choice of red, green, or amber through translucent white cap.
Short body of .551” (14.0mm) conserves behind-panel space.
Combination solder lug and .110” quick connect terminals.
Actual Size
www.nkk.com
D67
Supplement
Accessories
Indicators
Touch
Tilt
Tactiles
Crisp actuation and clear circuit status provided by snap-action contact mechanism. Arc barrier between movable contacts protects against crossover.
Slides
Rotaries
Keylocks
Programmable Illuminated PB
Pushbuttons
Environmentally friendly components and packaging materials meet RoHS Directive restricting use of hazardous materials. Suited for lead-free soldering because of heat resistant resin materials.
Rockers
Distinctive Characteristics
Series LP01
Toggles
Short Body Pushbuttons
TYPICAL SWITCH ORDERING EXAMPLE
Pushbuttons
Rockers
LP01
Poles
1 2 SPDT DPDT
1
C M
5
Bushing Snap-in
C
C
K
W01
5C
B
Mounting Types
Contacts & Terminals
Silver Rated 3A @ 125V AC/250V AC W01 Solder Lug/ Quick Connect Terminals*
Programmable Illuminated PB
D
Circuit
5 ON (ON) K ( ) = Momentary
Housing
Black 5C 5D 5F
LEDs
Red Amber Green B
Cap Color
White
Keylocks
IMPORTANT:
Switches are supplied without UL & cULus markings unless specified. Specific models & ratings noted on General Specifications page.
Nonilluminated No Nonilluminated Code
Nonilluminated Cap Colors A C F Black Red Green
Rotaries
Slides
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
* Wire harness & cable assemblies offered only in Americas
LP0115CCKW015CB
White Cap SPDT ON-(ON) Circuit Silver Contacts Rated 3A @ 125/250V AC; Solder Lug/Quick Connect Terminals Red LED Bushing Mount Black Housing
Tilt
Tactiles
Touch
P OLES & CIRCUIT
Plunger Position ( ) = Momentary Connected Terminals Normal Down Throw & Power/Lamp Schematics Note: Terminal markings “COM, NO, NC, L, + and – ” are actually on the switch; terminal numbers are not on the switch.
1 (COM)
Indicators
Normal Pole Model
Down
Accessories
SP
LP0115
ON
(ON)
1-3
1-2
SPDT
L (+) 3 1 (COM) 3 2 6 2 4 L (+) 5
(-) L
Supplement
DP
LP0125
ON
(ON)
1-3
4-6
1-2
4-5
DPDT
(-) L
D68
www.nkk.com
Short Body Pushbuttons
MOUNTING TYPES C
Bushing .630” (16.0mm) Diameter This mounting option is supplied with a brass hexagon nut with nickel plating.
0.2 (16.0) + 0.0 Dia – .630
Series LP01
M
Snap-in .669” (17.0mm) Diameter
Toggles
0.2 (18.1) + 0.0 – .713 0.2 (1.1) + 0.0 R – .043
(1.7) + 0.0 – 0.1 .067
+ 0.1 (7.5) – 0.0 .295
.079” ~ .256” (2.0mm ~ 6.5mm)
(25.0) Min .984
.039” ~ .126” (1.0mm ~ 3.2mm)
(21.0) Min .827
D
(17.3) .681
+ 0.2 – 0.0
Dia
Allow .984” (25.0mm) distance from center-to-center between switches when mounted side-by-side.
Allow .827” (21.0mm) distance from center-to-center between switches when mounted side-by-side.
K
Black
Housing available in black only. The one-piece body and bezel have a matte finish.
W01
Silver
Power Level
Solder Lug/ .110” (2.8mm) Quick Connect
Epoxy Seal (2.0) .079 (2.8) .110
(7.3) .287
3A @ 125V AC/250V AC; 3A @ 30V DC Note: If used at 1A @ 125V AC/250V AC or 1A @ 30V DC, electrical life will be 100,000 operations minimum.
(1.2) .047 Thk = (0.5) .020
LED COLORS & SPECIFICATIONS
The electrical specifications shown are determined at a basic temperature of 25°C. LED circuit is isolated and requires external power source. Polarity marks are on the switch. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement section. Single Color LED with 1 Element
(+) (-)
5C
Colors I FM IF VF VRM ∆I F Red 30mA 20mA 1.95V 5V 0.41mA/°C
5D
Amber 30mA 20mA 2.0V 5V 0.29mA/°C –10°C ~ +50°C
5F
Green 30mA
Indicators Touch
LEDs are an integral part of the switch and are not available separately.
Forward Peak Current Continuous Forward Current Forward Voltage Reverse Peak Voltage Current Reduction Rate Above 25°C Ambient Temperature Range
20mA 2.1V 5V 0.39mA/°C
No Code
No Lamp
www.nkk.com D69
Supplement
Accessories
Tilt
Tactiles
Slides
(0.6) R .024
Rotaries
CONTACT MATERIALS, RATINGS, & TERMINALS
Keylocks
HOUSING
Programmable Illuminated PB
Recommended Panel Thickness:
Recommended Panel Thickness:
Pushbuttons
Rockers
Series LP01
Toggles
Short Body Pushbuttons
CAP COLORS
Illuminated Cap
Rockers
Cap Color Available:
B
White
The translucent cap is an integral part of the switch and is not available separately. Material: Polycarbonate Finish: Matte
Pushbuttons
Programmable Illuminated PB
Nonilluminated Caps Cap Colors Available:
D
A
Black
C
Red
F
Green
The cap is an integral part of the switch and is not available separately. Material: Polycarbonate Finish: Matte
Keylocks
TYPICAL SWITCH DIMENSIONS
Bushing Mount • Single Pole
Rotaries
M16 P1
(1.2) x (2.0) Typ .047 x .079 (0.5) Typ .020
NO
(3.7) .146
3 2 1
NC
NO
Slides
(9.7) .382 (2.8) Typ .110
L –+
COM
Tactiles
(13.6) Dia .535 (20.0) Dia .787
(2.5) .098 (5.5) .217 (21.3) .838
(7.3) .287
(3.0) .118 (5.55) .219
LP0115CCKW015CB
Tilt
Bushing Mount • Double Pole
Touch
M16 P1
(1.2) x (2.0) Typ .047 x .079 (0.5) Typ .020
(3.7) .146
Indicators
NO
3 2
NC
6 5 4
NO
L –+ 1
COM
(9.7) .382
(2.8) Typ .110
Accessories
(13.6) Dia .535 (20.0) Dia .787
(2.5) .098 (5.5) .217 (21.3) .838
(7.3) .287
(6.0) .236 (11.1) .437
Supplement
LP0125CCKW015CB
D70
www.nkk.com
Short Body Pushbuttons
TYPICAL SWITCH DIMENSIONS
Series LP01
Snap-in • Single Pole
Rockers Toggles
(3.7) .146
NC
NO
(1.2) x (2.0) Typ .047 x .079 (0.5) Typ .020 (9.7) .382 (2.8) Typ .110
NO
3 2 1
L –+
COM
(13.6) Dia .535 (20.0) Dia .787
(2.5) .098 (5.5) .217 (21.3) .838
(7.3) .287
(3.0) .118 (5.55) .219
D
LP0115CMKW015CB
Snap-in • Double Pole
(1.2) x (2.0) Typ .047 x .079 (0.5) Typ .020
NO
(3.7) .146
3 2
6 L –+ 5 4
COM
(9.7) .382
(2.8) Typ .110
1
(13.6) Dia .535 (20.0) Dia .787
(5.5) .217
(21.3) .838
LP0125CMKW015DB
LEGENDS
NKK Switches can provide custom legends for caps. Contact factory for more information.
Tilt
Recommended Methods: Pad Print or Laser Etch on cap. Epoxy based ink is recommended.
(12.07) Dia .475 (13.6) Dia .535 (0.76) Typ .030
Shaded area is printable area
www.nkk.com
D71
Supplement
Accessories
Indicators
Touch
Suggested Printable Area for LP01 Cap
Tactiles
Slides
(2.5) .098
(7.3) .287
(6.0) .236 (11.1) .437
Rotaries
NC
NO
Keylocks
Programmable Illuminated PB
Pushbuttons
R PW
很抱歉,暂时无法提供与“LP0125CCKW015FB”相匹配的价格&库存,您可以联系我们找货
免费人工找货