LP0125CMKW015CB

Series LP01 Toggles Short Body Pushbuttons Rockers General Specifications Electrical Capacity (Resistive Load) Power Level (silver): 3A @ 125V AC or 3A @ 250V AC or 3A @ 30V DC Pushbuttons Other Ratings Programmable Illuminated PB D Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Contact Timing: Travel: 50 milliohms maximum 200 megohms minimum @ 500V DC 1,000V AC minimum between contacts for 1 minute minimum 1,500V AC minimum between contacts and case for 1 minute minimum 500,000 operations minimum 50,000 operations minimum for 3A @ 125V/250V AC & 3A @ 30V DC 100,000 operations minimum for 1A @ 125V/250V AC & 1A @ 30V DC 1.5N for Single Pole; 3.0N for Double Pole Nonshorting (break-before-make) Total Travel .118” (3.0mm) Keylocks Materials & Finishes Actuator: Housing: Base: Movable Contact: Stationary Contacts: Lamp Terminals: Slides Polycarbonate Bushing mount: Glass fiber reinforced polyamide (UL94V-0); Snap in mount: Polyphenylene ether (UL94V-0) Diallyl phthalate (UL94V-0) Phosphor bronze & silver with silver plating Common terminal: Phosphor bronze with silver plating; Contact terminals: Phosphor bronze with tin & copper plating Phospher bronze with tin and copper plating Rotaries Environmental Data Tactiles Operating Temperature Range: Humidity: Vibration: Shock: Tilt –10°C through +50°C (+14°F through +122°F) for Illuminated –25°C through +70°C (+13°F through +158°F) for Nonilluminated 90 ~ 95% humidity for 240 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Installation Touch Mounting Torque: Soldering Time & Temperature: Cleaning: 0.8Nm (7.08 lb • in) Manual Soldering: See Profile A in Supplement section. Hand clean locally with alcohol based solution Indicators Standards & Certifications Flammability Standards: UL: Supplement Accessories UL94V-0 housing & base File No. E44145 All single & double pole models recognized at 3A @ 125V/250V AC or 3A @ 30V DC. Add “/U” to end of part number to order UL mark on switch. Add “/CUL” to end of part number to order cULus mark on switch. D66 www.nkk.com Short Body Pushbuttons Series LP01 Toggles Smooth, slightly concave surface of cap designed to fit fingertip. Unique design and construction of cap prevents its removal and limits tampering. D Bright LED illumination in choice of red, green, or amber through translucent white cap. Short body of .551” (14.0mm) conserves behind-panel space. Combination solder lug and .110” quick connect terminals. Actual Size www.nkk.com D67 Supplement Accessories Indicators Touch Tilt Tactiles Crisp actuation and clear circuit status provided by snap-action contact mechanism. Arc barrier between movable contacts protects against crossover. Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Environmentally friendly components and packaging materials meet RoHS Directive restricting use of hazardous materials. Suited for lead-free soldering because of heat resistant resin materials. Rockers Distinctive Characteristics Series LP01 Toggles Short Body Pushbuttons TYPICAL SWITCH ORDERING EXAMPLE Pushbuttons Rockers LP01 Poles 1 2 SPDT DPDT 1 C M 5 Bushing Snap-in C C K W01 5C B Mounting Types Contacts & Terminals Silver Rated 3A @ 125V AC/250V AC W01 Solder Lug/ Quick Connect Terminals* Programmable Illuminated PB D Circuit 5 ON (ON) K ( ) = Momentary Housing Black 5C 5D 5F LEDs Red Amber Green B Cap Color White Keylocks IMPORTANT: Switches are supplied without UL & cULus markings unless specified. Specific models & ratings noted on General Specifications page. Nonilluminated No Nonilluminated Code Nonilluminated Cap Colors A C F Black Red Green Rotaries Slides DESCRIPTION FOR TYPICAL ORDERING EXAMPLE * Wire harness & cable assemblies offered only in Americas LP0115CCKW015CB White Cap SPDT ON-(ON) Circuit Silver Contacts Rated 3A @ 125/250V AC; Solder Lug/Quick Connect Terminals Red LED Bushing Mount Black Housing Tilt Tactiles Touch P OLES & CIRCUIT Plunger Position ( ) = Momentary Connected Terminals Normal Down Throw & Power/Lamp Schematics Note: Terminal markings “COM, NO, NC, L, + and – ” are actually on the switch; terminal numbers are not on the switch. 1 (COM) Indicators Normal Pole Model Down Accessories SP LP0115 ON (ON) 1-3 1-2 SPDT L (+) 3 1 (COM) 3 2 6 2 4 L (+) 5 (-) L Supplement DP LP0125 ON (ON) 1-3 4-6 1-2 4-5 DPDT (-) L D68 www.nkk.com Short Body Pushbuttons MOUNTING TYPES C Bushing .630” (16.0mm) Diameter This mounting option is supplied with a brass hexagon nut with nickel plating. 0.2 (16.0) + 0.0 Dia – .630 Series LP01 M Snap-in .669” (17.0mm) Diameter Toggles 0.2 (18.1) + 0.0 – .713 0.2 (1.1) + 0.0 R – .043 (1.7) + 0.0 – 0.1 .067 + 0.1 (7.5) – 0.0 .295 .079” ~ .256” (2.0mm ~ 6.5mm) (25.0) Min .984 .039” ~ .126” (1.0mm ~ 3.2mm) (21.0) Min .827 D (17.3) .681 + 0.2 – 0.0 Dia Allow .984” (25.0mm) distance from center-to-center between switches when mounted side-by-side. Allow .827” (21.0mm) distance from center-to-center between switches when mounted side-by-side. K Black Housing available in black only. The one-piece body and bezel have a matte finish. W01 Silver Power Level Solder Lug/ .110” (2.8mm) Quick Connect Epoxy Seal (2.0) .079 (2.8) .110 (7.3) .287 3A @ 125V AC/250V AC; 3A @ 30V DC Note: If used at 1A @ 125V AC/250V AC or 1A @ 30V DC, electrical life will be 100,000 operations minimum. (1.2) .047 Thk = (0.5) .020 LED COLORS & SPECIFICATIONS The electrical specifications shown are determined at a basic temperature of 25°C. LED circuit is isolated and requires external power source. Polarity marks are on the switch. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement section. Single Color LED with 1 Element (+) (-) 5C Colors I FM IF VF VRM ∆I F Red 30mA 20mA 1.95V 5V 0.41mA/°C 5D Amber 30mA 20mA 2.0V 5V 0.29mA/°C –10°C ~ +50°C 5F Green 30mA Indicators Touch LEDs are an integral part of the switch and are not available separately. Forward Peak Current Continuous Forward Current Forward Voltage Reverse Peak Voltage Current Reduction Rate Above 25°C Ambient Temperature Range 20mA 2.1V 5V 0.39mA/°C No Code No Lamp www.nkk.com D69 Supplement Accessories Tilt Tactiles Slides (0.6) R .024 Rotaries CONTACT MATERIALS, RATINGS, & TERMINALS Keylocks HOUSING Programmable Illuminated PB Recommended Panel Thickness: Recommended Panel Thickness: Pushbuttons Rockers Series LP01 Toggles Short Body Pushbuttons CAP COLORS Illuminated Cap Rockers Cap Color Available: B White The translucent cap is an integral part of the switch and is not available separately. Material: Polycarbonate Finish: Matte Pushbuttons Programmable Illuminated PB Nonilluminated Caps Cap Colors Available: D A Black C Red F Green The cap is an integral part of the switch and is not available separately. Material: Polycarbonate Finish: Matte Keylocks TYPICAL SWITCH DIMENSIONS Bushing Mount • Single Pole Rotaries M16 P1 (1.2) x (2.0) Typ .047 x .079 (0.5) Typ .020 NO (3.7) .146 3 2 1 NC NO Slides (9.7) .382 (2.8) Typ .110 L –+ COM Tactiles (13.6) Dia .535 (20.0) Dia .787 (2.5) .098 (5.5) .217 (21.3) .838 (7.3) .287 (3.0) .118 (5.55) .219 LP0115CCKW015CB Tilt Bushing Mount • Double Pole Touch M16 P1 (1.2) x (2.0) Typ .047 x .079 (0.5) Typ .020 (3.7) .146 Indicators NO 3 2 NC 6 5 4 NO L –+ 1 COM (9.7) .382 (2.8) Typ .110 Accessories (13.6) Dia .535 (20.0) Dia .787 (2.5) .098 (5.5) .217 (21.3) .838 (7.3) .287 (6.0) .236 (11.1) .437 Supplement LP0125CCKW015CB D70 www.nkk.com Short Body Pushbuttons TYPICAL SWITCH DIMENSIONS Series LP01 Snap-in • Single Pole Rockers Toggles (3.7) .146 NC NO (1.2) x (2.0) Typ .047 x .079 (0.5) Typ .020 (9.7) .382 (2.8) Typ .110 NO 3 2 1 L –+ COM (13.6) Dia .535 (20.0) Dia .787 (2.5) .098 (5.5) .217 (21.3) .838 (7.3) .287 (3.0) .118 (5.55) .219 D LP0115CMKW015CB Snap-in • Double Pole (1.2) x (2.0) Typ .047 x .079 (0.5) Typ .020 NO (3.7) .146 3 2 6 L –+ 5 4 COM (9.7) .382 (2.8) Typ .110 1 (13.6) Dia .535 (20.0) Dia .787 (5.5) .217 (21.3) .838 LP0125CMKW015DB LEGENDS NKK Switches can provide custom legends for caps. Contact factory for more information. Tilt Recommended Methods: Pad Print or Laser Etch on cap. Epoxy based ink is recommended. (12.07) Dia .475 (13.6) Dia .535 (0.76) Typ .030 Shaded area is printable area www.nkk.com D71 Supplement Accessories Indicators Touch Suggested Printable Area for LP01 Cap Tactiles Slides (2.5) .098 (7.3) .287 (6.0) .236 (11.1) .437 Rotaries NC NO Keylocks Programmable Illuminated PB Pushbuttons R PW