M2013TXW25-GC

Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers Toggles Series M Miniature Rockers General Specifications B Electrical Capacity (Resistive Load) Power Level (silver): 6A @ 125V AC & 3A @ 250V AC 4A @ 30V DC for On-None-On; 3A @ 30V DC for all other circuits Logic Level (gold): 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Logic/Power Level (gold over silver): Combines silver & gold ratings Note: Find additional explanation of dual rating & operating range in Supplement section. Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Angle of Throw: 10 milliohms maximum for silver; 20 milliohms maximum for gold 1,000 megohms minimum @ 500V DC 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts and case for 1 minute minimum 50,000 operations minimum 25,000 operations minimum for silver; 50,000 operations minimum for gold; 50,000 operations minimum for silver at 3A @ 125V AC 25° Materials & Finishes Actuator Clip & Mounting Frame: Body Frame: Case: Movable Contactor: Movable Contacts: Stationary Contacts: Terminals: Stainless Steel Stainless steel Diallyl phthalate resin (UL94V–0) Phosphor bronze with silver or gold plating Silver alloy (code W); copper with gold plating (code G); or silver alloy with gold plating (code A) Silver with silver plating (code W); copper or brass with gold plating (code G); or silver with gold plating (code A) Copper or brass with silver plating; or copper or brass with gold plating Operating Temp Range: Humidity: Vibration: Shock: Processing Soldering: Cleaning: –30°C through +85°C (–22°F through +185°F) 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Wave Soldering (PC version) for Gold: See Profile A in Supplement section. Manual Soldering for Gold: See Profile A in Supplement section. Wave Soldering (PC version) for Silver: See Profile B in Supplement section. Manual Soldering for Silver: See Profile B in Supplement section. Note: Actuator must be in OFF (center) position while soldering. These devices are not process sealed. Hand clean locally using alcohol based solution. Standards & Certifications Flammability Standards: UL94V–0 for case UL: File No. E44145 - Recognized only when ordered with marking on switch. Add “/U” before first dash in part number to order UL recognized switch. All models recognized at 6A @ 125V AC, 3A @ 250V AC or 0.4VA maximum @ 28V DC maximum. CSA: File No. 023535_0_000 - Certified only when ordered with marking on switch. Add “/C” before first dash in part number to order CSA certified switch. All models certified at 6A @ 125V AC or 3A @ 250V AC or 0.4VA maximum @ 28V maximum. Supplement Accessories Indicators Touch Tilt Tactiles Environmental Data B62 www.nkk.com Distinctive Characteristics B Pushbuttons Three methods of panel mounting: flat frame for flush with face or subpanel, snap-in, and PCB. Rockers Toggles Series M Miniature Rockers Programmable Illuminated PB High insulating barriers increase isolation of circuits in multipole devices and provide added protection to contact points. The molded diallyl phthalate case has a UL 94V-0 flammability rating. Epoxy sealed terminals prevent entry of solder flux and other contaminants. Keylocks Prominent external insulating barriers increase insulation resistance and dielectric strength. Slides Rotaries Bias guard prevents misalignment of contacts; interlocking of actuator block with rocker and internal guide does not allow transmission of diagonal force on rocker to reach contact mechanism. Snap-in Mount Page B64 Flat Frame Mount www.nkk.com Page B83 B63 Supplement Accessories Bracket PC Mount Page B72 Indicators Actual Size Touch Tilt Tactiles Clinching of the frame to the case well above the base and terminals provides 1,500V dielectric strength. Keylocks 4PDT DP3T (used only with terminal code 41 & frame code TX) TZ 2 ON NONE ON 3 ON OFF ON 5 ON NONE (ON) 8 (ON) OFF (ON) 9 ON OFF (ON) *4 ON ON ON *6 (ON) ON (ON) *7 ON ON (ON) C Red E .365” (9.27mm) Wide Paddle E Yellow F Green F .450” (11.43mm) Wide Rocker G Blue H Gray G .450” (11.43mm) Wide Paddle .964” (24.5mm) Straight PC with 1.150” (29.2mm) Bracket W Silver; Rated 6A @ 125V AC & 3A @ 250V AC 23 G Gold; Rated 0.4VA max @ 28V AC/DC max .250” (6.35mm) Straight PC with .465” (11.8mm) Bracket 25 J .595” (15.11mm) Wide Rocker A Gold over Silver; Rated 6A @ 125V AC & 0.4VA max @ 28V AC/DC max .425” (10.8mm) Straight PC with .630” (16.0mm) Bracket 26 .750” (19.05mm) Straight PC with .953” (24.2mm) Bracket H .595” (15.11mm) Wide Paddle Large Actuators (TZ Frame) Terminals For TX Frame Only Switches are supplied without UL & CSA marking unless specified. UL & CSA recognized only when ordered with marking on the switch. Specific models, ratings, & ordering instructions are noted on General Specifications page. .150” (3.81mm) Right Angle PC Tilt Vertical PC with Support (1-4 Pole) DESCRIPTION FOR TYPICAL ORDERING EXAMPLE DESCRIPTION FOR TYPICAL ORDERING EXAMPLE M2013TXG41-DC M2022TZG23-JC SPDT ON-OFF-ON Circuit Accessories .150” (3.81mm) Vertical PC Gold Contacts with 0.4VA Rating TX Frame with .365” (9.27mm) Wide Red Rocker TZ Frame with .595” (15.11mm) Wide Red Rocker Gold Contacts with 0.4VA Rating DPDT ON-NONE-ON Circuit .250” (6.35mm) Straight PC Terminals with Reinforced Bracket Supplement .150” (3.81mm) Vertical PC Terminals with Support Indicators Indicators Touch 41 B1 www.nkk.com Rockers IMPORTANT: Right Angle PC with Support (1-3 Pole only) 30 Black White 17 * 3-ON circuits A B .425” (10.8mm) Straight PC with .630” (16.0mm) Bracket Straight PC with Reinforced Bracket (1-2 Pole only) Rocker & Paddle Colors .365” (9.27mm) Wide Rocker 15 Pushbuttons Small Actuators (TX Frame) D ( ) = Momentary Tactiles Straight PC with Bracket (1-2 Pole only) .250” (6.35mm) Straight PC with .465” (11.8mm) Bracket 13 Contact Materials & Ratings Circuits Rockers & Paddles Programmable Illuminated PB 3 3PDT (used only with terminal codes 30 & 41 & frame code TX) Wide Frame for Large Actuator Terminals For TX & TZ Frames B Keylocks DPDT SP3T Narrow Frame for Small Actuator C Rotaries 2 TX D Slides SPDT Rotaries Slides 41 Mounting Frames 1 4 G Tactiles Programmable Illuminated PB Poles TX Tilt 3 Touch 1 Accessories M20 B ORDERING EXAMPLE www.nkk.com Supplement TYPICAL SWITCH Toggles Bracket PC Mount Miniature Rockers Pushbuttons Rockers Toggles Series M B1 Series M Toggles Bracket PC Mount Miniature Rockers POLES & CIRCUITS Rocker Position ) = Momentary B Programmable Illuminated PB Down Center Up Down Model SP M2012 M2013 *M2015 M2018 *M2019 ON ON ON (ON) ON NONE OFF NONE OFF OFF ON ON (ON) (ON) (ON) M2022 M2023 *M2025 M2028 *M2029 ON ON ON (ON) ON NONE OFF NONE OFF OFF ON ON (ON) (ON) (ON) M2022 M2023 *M2025 M2028 *M2029 ON ON ON (ON) ON NONE OFF NONE OFF OFF ON ON (ON) (ON) (ON) 2-3 5-6 8-9 M2042 M2043 *M2045 M2048 *M2049 ON ON ON (ON) ON NONE OFF NONE OFF OFF ON ON (ON) (ON) (ON) 2-3 5-6 8-9 11-12 DP 3P Rotaries Keylocks Connected Terminals Pole Pushbuttons Rockers ( Slides 4P Center Throw & Schematics Up Note: Terminal numbers are not actually on the switch. * Reverse circuits available for vertical mount SP & DP upon request. SPDT 2-3 OPEN 2 (COM) 2-1 3 1 DPDT 2-3 5-6 OPEN 2 2-1 5-4 (COM) 3 5 1 6 4 3PDT 2-1 5-4 8-7 OPEN 2 3 5 1 (COM) 6 4 8 9 7 8 11 4PDT 2-1 5-4 8-7 11-10 OPEN 5 2 3 1 (COM) 9 4 6 7 12 10 Tilt Tactiles For 3 Throw (3-On) Connected Terminals & Schematics Pole SP Model M2024 M2026 M2027 Down Center ON (ON) ON ON ON ON Up ON (ON) (ON) ON ON ON ON (ON) (ON) Accessories B74 3 4 (out) 6 (out) 2-3 5-6 8-9 11-12 6 3 5 2 4 1 (out) External Connection 2 (in) 5 1 (out) 2-1 5-4 External Connection 8 (in) 11 External Connection 2 (in) 5 3 4 (out) 6 (out) 7 (out) 9 10 (out) 12 (out) 1 (out) 3 4 (out) 6 (out) 7 (out) 9 10 (out) 12 (out) 2-3 5-4 8-9 11-10 External connection must be made during field installation. 3 4 (out) 6 (out) 1 (out) External Connection 8 (in) 11 Common (in) www.nkk.com External Connection 2 (in) 5 3 4 (out) 6 (out) The DP3T model utilizes a four pole base. (out) Up 2-3 5-4 External Connection 8 (in) 11 (out) External Conn 1 (out) 1 (out) 3 4 (out) 6 (out) 7 (out) 9 10 (out) 12 (out) External connection must be made during field installation. External Connection 2 (in) 5 External Connection 2 (in) 5 The SP3T model utilizes a double pole base. External Connection 2 (in) 5 2-3 5-6 Touch ON (ON) ON Supplement Indicators M2044 M2046 M2047 Center 1 (out) DP Down 2-1 5-4 8-7 11-10 (out) External Conn Common (in) (out) (out) 12 9 11 8 5 2 10 7 4 1 (out) 6 3 (out) Common (in) (out) Series M MOUNTING FRAMES Narrow Mounting Frame for Small Actuators with Straight PC Terminals (codes 13, 15, 17, 23, 25, & 26) or with Angle PC Terminals (codes 30 & 41) (2.54) Dia .100 (8.0) .315 (1.4) Typ .055 (3.5) .138 25° 25° (2.54) Dia .100 (2.54) Dia .100 (4.37) .172 (0.4) Typ .016 (5.08) .200 (2.75) .108 Pushbuttons (5.08) .200 25° B Vertical PC Mounting (6.0) .235 (1.27) .050 Small Actuators & Panel Cutouts for TX Frame (actuator details on the following pages) AT4150 (12.7) .500 (12.4) .490 (10.1) .398 TZ Wide Mounting Frame for Large Actuators with Straight PC Terminals (codes 13, 15, 17, 23, 25, & 26) Direction of Actuation Direction of Actuation (17.8) .701 AT4151 Rotaries AT4149 Large Actuators & Panel Cutouts for TZ Frame (actuator details on the following pages) AT4156 Slides AT4148 Programmable Illuminated PB Right Angle PC Mounting Keylocks Straight PC Mounting AT4157 (2.54) Dia .100 Tilt (3.5) .138 Direction of Actuation (28.5) 1.122 25° Tactiles TX Rockers Toggles Bracket PC Mount Miniature Rockers (16.0) .630 Silver over Silver Power Level 6A @ 125V AC & 3A @ 250V AC G Gold over Brass or Copper Logic Level 0.4VA maximum @ 28V AC/DC maximum Indicators W Touch CONTACT MATERIALS & RATINGS Gold over Silver Power Level or Logic Level 6A @ 125V AC or 0.4VA maximum @ 28V AC/DC maximum Supplement A Accessories Note: See Supplement section to find complete explanation of operating range. Note: This dual rated option is suitable when two or more identical switches are used in logic and in power circuits within the same application. See Supplement section to find complete explanation of dual rating and operating range. www.nkk.com B75 Series M TERMINALS For TX and TZ 1-2 Pole Straight PC Mount with Bracket B 13 15 .250” (6.35mm) Terminal with .465” (11.8mm) Bracket For TX and TZ 1-2 Pole Straight PC Mount with Reinforced Bracket 17 .425” (10.8mm) Terminal with .630” (16.0mm) Bracket 23 .964” (24.5mm) Terminal with 1.150” (29.2mm) Bracket 25 .250” (6.35mm) Terminal with .465” (11.8mm) Bracket 26 .425” (10.8mm) Terminal with .630” (16.0mm) Bracket .750” (19.05mm) Terminal with .953” (24.2mm) Bracket Keylocks Programmable Illuminated PB Pushbuttons Rockers Toggles Bracket PC Mount Miniature Rockers PCB footprints are on the following Typical Switch Dimension pages. For TX 1-3 Pole Right Angle PC Mount .150” (3.81mm) Right Angle PC 41 .150” (3.81mm) Vertical PC ROCKERS & PADDLES FOR TX MOUNTING FRAMES D AT4148 .365” (9.27mm) Wide Rocker Material: Polyamide Finish: Matte E (9.27) .365 Tilt Tactiles Slides Rotaries 30 For TX 1-4 Pole Vertical PC Mount AT4149 .365” (9.27mm) Wide Paddle (9.27) (16.87) .664 (13.49) .531 (2.13) .084 .365 Material: Polyamide Finish: Matte (3.96) .156 (18.8) .740 Touch (3.5) .138 Material: Polyamide Finish: Matte G (11.43) .450 AT4151 .450” (11.43mm) Wide Paddle (2.36) .093 (11.43) .450 Material: Polyamide Finish: Matte (11.8) .465 (9.19) .362 (3.18) .125 (16.36) .644 (7.7) .303 (8.1) (6.3) .319 .248 Supplement (3.5) .138 Cap Colors Available: B76 A Black B White C Red www.nkk.com (3.5) .138 (16.8) .661 AT4150 .450” (11.43mm) Wide Rocker Accessories Indicators F (8.43) R .332 (8.8) .346 (7.9) (6.15) .311 .242 (5.84) R .230 (11.8) .465 E Yellow F Green G Blue H Gray (3.5) .138 Series M ROCKERS & PADDLES FOR TZ MOUNTING FRAMES AT4156 .595” (15.11mm) Wide Rocker H (2.36) .093 (14.33) .564 (26.78) 1.054 (29.82) 1.174 (23.01) .906 (7.3) .287 (3.5) .138 A (13.5) R .531 (11.0) .433 (8.4) (6.5) .331 .256 Black B White Programmable Illuminated PB (4.75) .187 (15.11) .595 Cap Colors Available: B Material: Polyamide Finish: Matte Pushbuttons Material: Polyamide Finish: Matte AT4157 .595” (15.11mm) Wide Paddle C E Red Yellow (3.5) .138 (26.8) 1.055 (15.11) .595 F Green G Blue H Gray Keylocks J OPTIONAL SNAP-IN PANEL FRAMES Material: Polyamide Finish: Matte Color: Black (25.04) .986 (15.62) .615 Tactiles (6.68) .263 Mounted separately from switches A B Tilt Cutout Tolerances: Dimension A: .797” ~ .803” (20.24 ~ 20.4mm) Dimension B: .495” ~ .505” (12.57 ~ 12.83mm) (2.3) .090 (9.9) .390 (17.9) .705 Slides AT064-2 Accommodates .062” ~ .125” (1.57 ~ 3.18mm) panel thickness Rotaries Used with AT4148 Rocker and AT4149 Paddle AT064-1 Accommodates .047” ~ .090” (1.2 ~ 2.3mm) panel thickness Rockers Toggles Bracket PC Mount Miniature Rockers AT064–1 Enlarged Detail Material: Polyamide Finish: Matte Color: Black (15.62) .615 (12.0) .472 (2.3) .090 (19.43) .765 Accessories (6.68) .263 Mounted separately from switches Cutout Tolerances: Dimension A: .595” ~ .605” (15.11 ~ 15.37mm) Dimension B: .495” ~ .500” (12.57 ~ 12.7mm) (12.8) .504 Indicators AT065-2 Accommodates .062” ~ .125” (1.57 ~ 3.18mm) panel thickness A B AT065–1 Enlarged Detail www.nkk.com AT065–2 Enlarged Detail B77 Supplement AT065-1 Accommodates .047” ~ .090” (1.2 ~ 2.3mm) panel thickness Touch Used with AT4150 Rocker and AT4151 Paddle Series M Toggles Bracket PC Mount Miniature Rockers TYPICAL SWITCH DIMENSIONS Straight PC • Bracket B Programmable Illuminated PB TE RMI NAL LE NGTH Single Pole Double Pole Circuit Mark This Side (3.5) .138 B R AC KE T LE N GT H 2 1 (0.5) Typ .020 (0.8) Typ .031 (4.7) Typ .185 (4.8) Typ .189 3 (1.17) Typ .046 (1.17) Typ .046 (8.0) .315 (15.8) .622 (4.8) .189 (3.2) Typ .126 (12.7) .500 M2012TXG13-DC Keylocks Terminal Code: Rotaries Slides (8.8) .346 (6.15) .242 Pushbuttons Rockers 25° Terminal Length: Bracket Length: (1.6) Typ .063 (2.4) Typ .095 (1.6) Typ .063 13 .250” (6.35mm) .465” (11.8mm) 15 .425” (10.8mm) .630” (16.0mm) 17 .964” (24.5mm) 1.150” (29.2mm) (7.9) Typ .311 (4.7) Typ .185 3 (7.9) Typ .311 2 (4.7) Typ .185 1 (1.8) Dia Typ .073 (1.5) Dia Typ .059 (1.8) Dia Typ .073 (1.5) Dia Typ .059 3 6 2 5 1 4 CL Straight PC • Reinforced Bracket 25° (8.8) .346 Tactiles (6.15) .242 Tilt Touch (0.5) Typ .020 (0.8) Typ .031 (4.7) Typ .185 Double Pole Circuit Mark This Side (3.5) .138 TE RMI NAL LE NGTH Single Pole B R AC KE T LE N GT H 2 1 (4.8) Typ .189 3 (1.17) Typ .046 (1.17) Typ .046 (9.1) .358 (19.05) .750 (12.7) .500 (6.35) Typ .250 (4.8) .189 Terminal Code: Terminal Length: Bracket Length: Accessories 23 .250” (6.35mm) .465” (11.8mm) 25 .425” (10.8mm) .630” (16.0mm) Supplement Indicators M2012TXG23-DC 26 .750” (19.05mm) .953” (24.2mm) B78 (2.4) Typ .095 (3.18) Typ .125 (3.18) Typ .125 www.nkk.com (9.53) Typ .375 3 (9.53) Typ .375 2 (4.7) Typ .185 (1.8) Dia Typ .073 (1.5) Dia Typ .059 1 (4.7) Typ .185 (1.8) Dia Typ .073 (1.5) Dia Typ .059 3 6 2 5 1 4 CL Series M Toggles Bracket PC Mount Miniature Rockers TYPICAL SWITCH DIMENSIONS .150” (3.81mm) Right Angle PC B 1 2 3 (7.9) .311 (9.27) .365 (5.41) .213 3 2 (4.7) Typ .185 1 (4.3) .169 (0.4) .016 (2.85) .112 (1.4) Typ .055 (5.08) .200 (5.5) .217 (4.0) .157 (12.7) .500 (6.15) .242 (8.8) .346 (1.27) .050 (12.7) .500 (0.8) Typ .031 (4.7) Typ .185 (13.0) .512 Pushbuttons Pivot Programmable Illuminated PB Shown in Down Position (1.8) Dia Typ .073 (2.54) Typ .100 M2012TXG30-DC Double Pole Shown in Down Position (9.27) .365 5 6 1 2 3 (12.7) .500 6 5 4 3 2 1 (6.15) .242 (0.4) Typ .016 (4.0) .157 (12.7) .500 (0.8) Typ .031 (4.7) Typ .185 (13.0) .512 (3.81) .150 (2.54) Typ .100 (1.8) Dia Typ .073 Tactiles (8.8) .346 (1.27) Typ .050 (3.81) .150 (4.7) Typ .185 (12.7) .500 (4.3) .169 (2.85) .112 (1.4) Typ .055 (5.08) .200 Rotaries Pivot Slides (6.4) .252 .150” (3.81mm) Right Angle PC 4 Rockers Single Pole Keylocks Three Pole Shown in Down Position Pivot 9 4 5 6 1 2 9 (17.5) .689 (6.15) .242 (8.8) .346 (0.4) .016 (4.5) .177 (14.35) .565 (1.27) Typ .050 (3.81) Typ .150 7 6 5 4 3 2 1 (4.7) Typ .185 (3.81) Typ .150 3 (4.3) .169 (2.85) .112 (1.4) Typ .055 (5.08) .200 8 Indicators 8 (0.8) Typ .031 (4.7) Typ .185 (13.0) .512 (14.35) .565 Accessories (9.27) .365 7 (2.54) Typ .100 (1.8) Dia Typ .073 Supplement (8.8) .346 .150” (3.81mm) Right Angle PC Touch M2032TXG30-DC www.nkk.com Tilt M2022TXG30-DC B79 Series M Toggles Bracket PC Mount Miniature Rockers TYPICAL SWITCH DIMENSIONS Rockers .150” (3.81mm) Vertical PC B Single Pole (8.8) .346 (9.27) .365 (3.5) .138 3 Pushbuttons 25° (9.1) .360 (3.81) Typ .150 1 (3.18) .125 (12.7) .500 (1.27) .050 (12.7) .500 (2.74) .108 Shown in (6.15) (5.97) Down Position .242 .235 (0.4) Typ .016 (5.08) .200 (0.8) Typ .031 (3.81) Typ .150 (1.27) .050 (7.9) .311 (2.54) Typ .100 (1.8) Dia Typ .073 M2012TXG41-DC .150” (3.81mm) Vertical PC Double Pole (9.27) .365 (8.8) .346 Keylocks Programmable Illuminated PB 2 (13.0) .512 (3.5) .138 25° (9.1) .360 Rotaries (0.4) Typ .016 (5.08) .200 (1.27) .050 (12.7) .500 3 5 2 4 (3.18) .125 (2.74) .108 (6.15) (5.97) Shown in Down Position .242 .235 6 (0.8) Typ .031 (3.81) Typ .150 (13.0) .512 1 3 6 2 5 1 4 (2.4) Typ .094 (3.81) Typ .150 (12.7) .500 (1.27) Typ .050 (4.8) .189 (12.7) .500 (2.54) Typ .100 (1.8) Dia Typ .073 Slides M2022TXG41-DC .150” (3.81mm) Vertical PC Three Pole (9.27) .365 (8.8) .346 (3.5) .138 Tactiles 9 25° (9.1) .360 Tilt (0.4) Typ .016 (5.08) .200 6 3 8 5 2 7 4 1 (13.0) .512 3 6 9 2 5 8 1 4 7 (3.18) .125 (2.74) .108 Shown in Down Position (6.15) (5.97) .242 .235 (1.27) .050 (14.35) .565 (2.54) Typ .100 (1.8) Dia Typ .073 Four Pole (9.27) .365 Indicators Touch M2032TXG41-DC .150” (3.81mm) Vertical PC (8.8) .346 (3.5) .138 25° Accessories (9.1) .360 Supplement (0.4) Typ .016 (5.08) .200 12 9 6 3 11 8 5 2 10 7 4 (13.0) .512 1 (3.18) .125 (2.74) .108 (6.15) (5.97) Shown in Down Position .242 .235 (1.27) .050 (14.35) .565 M2042TXG41-DC B80 (3.81) Typ .150 (14.35) .565 (1.27) Typ .050 (4.8) Typ .189 (17.5) .689 (0.8) Typ .031 (3.81) Typ .150 (4.8) Typ .189 www.nkk.com (0.8) Typ .031 (3.81) Typ .150 3 6 9 12 2 5 8 11 1 4 7 10 (4.8) Typ .189 (3.81) Typ .150 (14.35) .565 (4.8) Typ .189 (22.3) .878 (1.27) Typ .050 (2.54) Typ .100 (1.8) Dia Typ .073 Series M Toggles Bracket PC Mount Miniature Rockers TYPICAL SWITCH DIMENSIONS 25° 2 Pushbuttons B R AC KE T LE N GT H (4.8) Typ .189 3 (1.17) Typ .046 (1.17) Typ .046 (15.8) .622 (8.0) .315 (12.7) .500 Programmable Illuminated PB 1 (0.6) Typ .024 (0.8) Typ .031 (4.7) Typ .185 B Double Pole Circuit Mark This Side (3.5) .138 T ERMIN A L LEN G T H Single Pole (4.8) .189 (3.2) Typ .126 3 (7.9) Typ .311 (7.9) Typ .311 2 (4.7) Typ .185 3 6 2 5 1 4 (4.7) Typ .185 1 (1.8) Dia Typ .073 (1.5) Dia Typ .059 (1.8) Dia Typ .073 (1.5) Dia Typ .059 CL Terminal Code: Terminal Length: Bracket Length: 13 .250” (6.35mm) .465” (11.8mm) 15 .425” (10.8mm) .630” (16.0mm) 17 .964” (24.5mm) 1.150” (29.2mm) Rotaries (1.6) Typ .063 (2.4) Typ .095 (1.6) Typ .063 Keylocks M2012TZG13-JC Straight PC • Reinforced Bracket Slides (11.0) .433 (6.6) .260 Rockers Straight PC • Bracket 25° Tactiles (4.8) Typ .189 3 (1.17) Typ .046 (1.17) Typ .046 (19.05) .750 (9.1) .358 (12.7) .500 (6.35) Typ .250 (4.8) .189 Touch 2 1 BRACKET LENGTH (9.53) Typ .375 3 (9.53) Typ .375 2 (4.7) Typ .185 (1.8) Dia Typ .073 (1.5) Dia Typ .059 1 (4.7) Typ .185 (1.8) Dia Typ .073 (1.5) Dia Typ .059 3 6 2 5 1 4 CL Terminal Code: Terminal Length: Bracket Length: 23 .250” (6.35mm) .465” (11.8mm) 25 .425” (10.8mm) .630” (16.0mm) 26 .750” (19.05mm) .953” (24.2mm) www.nkk.com Accessories (2.4) Typ .095 (3.18) Typ .125 (3.18) Typ .125 Indicators M2012TZG23-JC Supplement (0.5) Typ .020 (0.8) Typ .031 (4.7) Typ .185 Double Pole Circuit Mark This Side (3.5) .138 T E RMIN A L LENGTH Single Pole Tilt (11.0) .433 (6.6) .260 B81 Series M Toggles Bracket PC Mount Miniature Rockers LEGENDS Rockers NKK Switches can provide custom legends for caps. Contact factory for more information. B Pushbuttons Suggested Printable Area for Cap AT4148 AT4150 ON ON OF F F OF OF Programmable Illuminated PB ON AT4156 F Keylocks (0.38) Typ .015 (6.9) Typ .272 (0.76) Typ .030 (5.76) Typ .227 (7.75) .305 Rotaries (9.27) .365 (0.76) Typ .030 (0.38) Typ .015 (4.5) Typ .177 (0.76) Typ .030 (0.76) Typ .030 (3.36) Typ .132 Slides Recommended Print Method: Pad Print Epoxy based ink is recommended. Supplement Accessories Indicators Touch Tilt Tactiles (10.03) Typ .395 (11.18) Typ .440 (9.91) .390 (11.43) .450 Shaded areas are printable areas. B82 (0.38) Typ .015 www.nkk.com (0.76) Typ .030 (13.59) .535 (15.11) .595 (0.76) Typ .030