MB2185SD1A

Miniature Pushbuttons Series MB2000 Distinctive Characteristics Guide interlocked with actuator block prevents window locking and maintains correct plunger alignment to assure contact stability. Employs an over-center actuator mechanism, which diminishes sparking and increases operating life in AC circuits. High torque bushing construction prevents rotation or separation from frame during installation. Splashproof option (D3 and B3 bushing codes) features an o-ring within the bushing and one under the face nut to protect from splashed, sprayed, or spilled liquids. High insulating barriers, formed in the molded diallyl phthalate case, increase isolation of circuits in multipole devices. Prominent external insulating barriers increase insulation resistance and dielectric strength. Epoxy sealed terminals prevent entry of solder flux and other contaminants. Clinching of the frame to the case well above the base and terminals provides 1,500V dielectric strength. Actual Size N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Miniature Pushbuttons Series MB2000 General Specifications Electrical Capacity (Resistive Load) Power Level (code W): Logic Level (code G): Logic/Power Level (code A): 6A @ 125V AC & 3A @ 250V AC or 3A @ 30V DC 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Combines W & G ratings Note: Find additional explanation dual rating & operating range in Supplement section. 10 milliohms maximum for silver; 20 milliohms maximum for gold 1,000 megohms minimum @ 500V DC 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts & case for 1 minute minimum 50,000 operations minimum for splashproof models; 100,000 for all other models 25,000 operations minimum for silver; 50,000 operations minimum for gold 50,000 operations minimum for silver at 3A @ 125V AC Momentary Action: 1-pole 9.32N; 2-pole 16.18N; 4-pole 25.54N; Alternate Action: 1-pole 4.41N; 2-pole 7.06N; 4-pole 11.77N Slow make, slow break Screw-on Cap (Mom.) Screw-on Cap (Alt.) Snap-on Cap (Mom. & Alt.) .028” (0.71mm) .110” (2.80mm) .125” (3.19mm) .043” (1.09mm) .043” (1.10mm) .050” (1.26mm) .071” (1.80mm) .153” (3.90mm) .175” (4.45mm) Brass w/nickel plating; polyacetal w/B1 bushing Bushing: Brass with nickel plating Stainless steel Case: Diallyl phthalate resin (UL94V-0) Phosphor bronze with silver or gold plating Silver alloy (code W); copper with gold plating (code G); or silver alloy with gold plating (code A) Silver with silver plating (code W); copper or brass with gold plating (code G); or silver with gold plating (code A) Copper or brass with silver plating; copper or brass with gold plating –30°C through +85°C (–22°F through +185°F) 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) B3 & D3 bushing options equivalent to IP67 1.5Nm (13.0 lb • in) for double nut; .7Nm (6.0 lb • in) for single nut 80.0N (18.0 lbf) maximum downward force on actuator Wave Soldering (PC version): See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section. These devices are not process sealed. Hand clean locally using alcohol based solution. UL94V-0 case All models recognized at 6A @ 125V AC or 3A @ 250V AC or 0.4VA max. @ 28V DC max; UL File No. WOYR2.E44145; add “/U” to end of part number to order UL mark on switch C-UL File No. WOYR8.E44145; add “/C-UL” to end of part number to order C-UL mark on switch All models certified at 6A @ 125V AC or 3A @ 250V AC or 0.4VA max. @ 28V max; CSA File No. 023535-0-000; add “/C” to end of part number to order CSA mark on switch. Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Contact Timing: Plunger Travel: Pretravel: Overtravel: Total Travel Materials & Finishes Plunger: Frame: Movable Contactor: Movable Contacts: Stationary Contacts: Terminals: Environmental Data Operating Temp Range: Humidity: Vibration: Shock: Sealing: Installation Mounting Torque: Cap Installation Force: Soldering Time & Temp: Process Seal: Standards & Certifications Flammability Standards: UL & C-UL Recognized: R CSA Certified: N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Bushing Mount Miniature Pushbuttons Series MB2000 C CAPS B C .315” (8.0mm) Dia. .394” (10.0mm) Dia. TYPICAL SWITCH ORDERING EXAMPLE MB 2011 S S1 W 01 A POLES & CIRCUITS 2011 2065 2061 2085 2181 2185 SPDT SPDT DPDT DPDT 4PDT 4PDT ON ON ON ON ON ON (ON) ON (ON) ON (ON) ON C ONTACT MATERIALS & R ATINGS W Silver Rated 6A @ 125V AC & 3A @ 250V AC Gold Rated 0.4VA max @ 28V AC/DC max Gold over Silver Rated 6A @ 125V AC & 0.4VA max @ 28V AC/DC max G CAP COLORS A B C E F G H Black White Red Yellow Green Blue Gray ( ) = Momentary A PLUNGER TYPES S L Plunger for Screw-on Caps Plunger for Snap-on Caps S1 S2 S4 D1 D3 B USHINGS .335” (8.5mm) Threaded with Keyway .335” (8.5mm) Smooth with Keyway .335” (8.5mm) Metric Threaded with Keyway .335” (8.5mm) Threaded with D-Flat .335” (8.5mm) Threaded Splashproof without Keyway 01 02 03 05 06 07 08 TERMINALS Solder Lug Quick Connect .250” (6.35mm) Straight PC .425” (10.8mm) Wirewrap .750” (19.05mm) Wirewrap .964” (24.5mm) Wirewrap 1.062” (27.0mm) Wirewrap IMPORTANT: Switches are supplied without UL, C-UL, & CSA markings unless specified. Specific models & ratings noted on General Specifications page. DESCRIPTION FOR TYPICAL ORDERING EXAMPLE MB2011SS1W01-CA Black .394” (10.0mm) Diameter Cap Plunger for Screw-on Caps .335” (8.5mm) Threaded Bushing with Keyway SPDT ON-(ON) Circuit Silver Contacts with 6-Amp Rating Solder Lug Terminals N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Bushing Mount Miniature Pushbuttons P OLES & CIRCUITS Plunger Position ( ) = Momentary Normal Pole Model MB2011 SP MB2065 ON ON Keyway Series MB2000 Throw & Switch Schematics Note: Terminal numbers are not actually on the switch. Connected Terminals Normal Keyway Down Down ON (ON) 2-3 2-1 SPDT 3 2 (COM) 1 MB2061 DP MB2085 ON ON (ON) 2-3 5-6 ON 4PDT 2-3 5-6 8-9 11-12 2-1 5-4 8-7 11-10 2 3 1 6 5 2 (COM) 1 6 5 4 2-1 5-4 DPDT 3 MB2181 4P MB2185 ON ON (ON) ON (COM) 4 9 8 7 12 11 10 PLUNGER TYPES On alternate action models, after transferring circuit, the plunger returns to its original position and does not latch down. S Plunger for Screw-on Caps (2.9) .114 (2.9) .114 (3.0) .118 (2.3) .091 (4.7) .185 (4.0) .157 Momentary Plunger Length Momentary Cap Location Alternate Plunger Length Alternate Cap Location L Plunger for Snap-on Caps (3.0) Dia .118 (10.4) .410 (3.6) .142 Momentary & Alternate Plunger Length Momentary & Alternate Cap Location N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Bushing Mount Miniature Pushbuttons BUSHINGS S1 (0.8) .031 (9.0) Dia .354 Series MB2000 S4 .335” (8.5mm) Metric Threaded with Keyway (0.8) .031 (9.0) Dia .354 .335” (8.5mm) Threaded with Keyway S2 .335” (8.5mm) Smooth with Keyway 1/4-40 Thd (0.8) .031 (9.0) Dia .354 (6.2) Dia .244 M6P0.75 (2.5) .098 (8.5) .335 (3.5) .138 (2.5) .098 (8.5) .335 (3.5) .138 (2.5) .098 (8.5) .335 (3.5) .138 Maximum Panel Thickness with Standard Hardware: .154” (3.9mm) Maximum Panel Thickness with Standard Hardware: .154” (3.9mm) D1 .335” (8.5mm) Threaded with D Flat D3 1/4-40 Thd .335” (8.5mm) Threaded Splashproof without Keyway 1/4-40 Thd (10.0) Dia .394 (8.5) .335 (3.5) .138 (9.0) Dia .354 (2.5) .098 (8.5) .335 (3.5) .138 Maximum Panel Thickness with Standard Hardware: .154” (3.9mm) Panel Cutouts For S1, S2, or S4 Bushing with Keyway (5.6) .220 (6.5) Dia .256 (0.6) .024 Maximum Panel Thickness with Standard Hardware: .240” (6.1mm) For S1 or S4 Bushing with Optional Locking Ring For D1 Bushing with D Flat (5.8) .228 For D3 Bushing without Keyway (6.5) Dia .256 (2.2) Dia .087 (6.5) .256 (6.5) Dia .256 (6.5) Dia .256 Standard hardware for bushings S1, S4, & D1 includes 2 hex nuts & 1 lockwasher; D3 bushing has 1 hex nut & 1 o-ring. Standard & optional hardware are illustrated following the Typical Switch Dimension drawings. CONTACT MATERIALS & RATINGS W G Silver over Silver Power Level 6A @ 125V AC & 3A @ 250V AC Gold over Brass or Copper Logic Level 0.4VA maximum @ 28V AC/DC maximum Note: Complete explanation of operating range in Supplement section. A Gold over Silver Power Level or Logic Level 6A @ 125V AC & 3A @ 250V AC or 0.4VA maximum @ 28V AC/DC maximum Note: This dual rated option is suitable when two or more identical switches are used in logic and in power circuits within the same application. See Supplement section for complete explanation of dual rating and operating range. N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Bushing Mount Miniature Pushbuttons TERMINALS 01 Solder Lug Epoxy Seal (2.0) .079 Series MB2000 02 (4.0) .157 (2.0) (1.1) .079 .043 Thk = (0.8) .031 .062” (1.57mm) Wide Quick Connect Epoxy Seal (6.35) .250 (1.57) .062 Thk = (0.8) .031 03 .250” (6.35mm) Straight PC 3 3 (4.8) .189 6 5 4 3 6 5 4 9 8 7 12 11 10 (4.8) Typ .189 (4.7) Typ .185 Epoxy Seal (6.35) (4.8) .250 .189 2 1 (4.7) Typ .185 (1.8) Dia Typ .073 2 1 (4.7) Typ .185 2 1 (1.17) .046 Thk = (0.8) .031 (1.8) Dia Typ .073 (1.8) Dia Typ .073 Single Pole Double Pole Four Pole 05 06 07 08 .425” (10.8mm) Wirewrap or Extended PC .750” (19.05mm) Wirewrap or Extended PC .964” (24.5mm) Wirewrap or Extended PC 1.062” (27.0mm) Wirewrap or Extended PC Epoxy Seal If using as extended PC terminal, refer to the above footprints. A (1.27) .050 Dimension A = terminal lengths as shown beside the terminal codes at the left. Thk = (0.8) .031 CAPS & CAP COLORS B AT413 .315” (8.0mm) Dia. Screw-on Cap AT443 .315” (8.0mm) Dia. Snap-on Cap For use with Plunger Code L Cap Material: Polycarbonate Finish: Glossy C AT407 .394” (10.0mm) Dia. Screw-on Cap AT442 .394” (10.0mm) Dia. Snap-on Cap For use with Plunger Code L Cap Material: Polycarbonate Finish: Glossy For use with Plunger Code S Cap Material: PBT Finish: Glossy For use with Plunger Code S Cap Material: PBT Finish: Glossy (6.5) .256 (7.6) .299 (8.0) .315 (8.0) .315 (8.0) Dia .315 M2.3 P0.4 (8.0) Dia .315 (10.0) Dia .394 M2.3 P0.4 (10.0) Dia .394 Cap Colors Available: A Black B White C Red E Yellow F Green G Blue H Gray 03-07 N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com Bushing Mount Miniature Pushbuttons TYPICAL SWITCH DIMENSIONS Solder Lug Single Pole Series MB2000 1/4-40 Thd Keyway (1.1) x (2.0) Typ .043 x .079 (0.8) Typ .031 3 (10.0) Dia .394 (4.7) Typ .185 (0.5) .020 (4.5) .177 COM 2 1 (13.0) .512 (2.3) .091 (7.9) .311 (8.0) .315 (8.5) .335 (3.5) .138 (21.0) .827 (2.0) .079 MB2011SS1W01-CA Solder Lug Double Pole 1/4-40 Thd Keyway (10.0) Dia .394 (1.1) x (2.0) Typ .043 x .079 (0.8) Typ .031 6 3 2 1 (4.7) Typ .185 (0.5) .020 (4.5) .177 COM 5 4 (13.0) .512 (2.3) .091 (12.7) .500 (8.0) .315 (8.5) .335 (3.5) .138 (21.0) .827 (2.0) Typ .079 (4.8) .189 MB2061SS1W01-CA Solder Lug Four Pole 1/4-40 Thd Keyway (10.0) Dia .394 (1.1) x (2.0) Typ .043 x .079 (0.8) Typ .031 12 9 8 7 6 5 4 3 2 1 (4.7) Typ .185 (0.5) .020 COM 11 10 (13.0) .512 (2.3) .091 (22.3) .878 (8.0) .315 (3.5) .138 (8.5) .335 (4.5) .177 (21.0) .827 (2.0) Typ .079 (4.8) Typ .189 MB2181SS1W01-CA N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Bushing Mount Miniature Pushbuttons HARDWARE Standard Hardware AT513H for Inch AT513M for Metric Hexagon Nut 2 included with each switch (1 with splashproof models) Material: Brass with Nickel plating M6 P0.75 (8.0) .315 (6.4) Dia (10.2) Dia .252 .402 Series MB2000 Optional Hardware AT509 Lockwasher 1 included with each switch (not with splashproof models) Material: Steel with Zinc/Chromate AT516 O-ring for Splashproof Bushing 1 included with each splashproof model Material: Nitrile butadiene rubber AT507H for Inch AT507M for Metric Locking Ring Material: Steel with Zinc/Chromate (6.0) Dia .236 (6.07) Dia (9.63) Dia .239 .379 (2.0) .079 (5.5) .217 (12.0) Dia .472 (9.0) .354 (1.5) .059 (0.5) .020 (1.78) .070 (1.7) .067 (0.8) .031 Optional Mounting Collars/Conical Nuts AT512H for Inch AT512M for Metric Conical Nut Used with .315” (8.0mm) Dia. Cap (cap code B) Material: Brass with chrome plating AT512CH for Inch AT512CM for Metric Conical nut Used with .394” (10.0mm) Dia. Cap (cap code C) Material: Brass with chrome plating Optional Splashproof Boots for S Plunger AT4041H for Inch AT4041M for Metric Boot for Momentary Material: Silicone rubber AT4042H for Inch AT4042M for Metric Boot for Alternate Material: Silicone rubber M6 P0.75 or 1/4-40 Thd M2.3 P0.4 (13.0) Dia .512 (10.5) Dia .413 (14.0) Dia .551 (12.2) Dia .480 (10.8) .425 (4.9) Dia .193 (6.0) Dia .236 (8.5) .335 (10.0) .394 (8.5) .335 (10.0) .394 (10.8) .425 (4.9) Dia .193 (6.0) Dia .236 A (8.5) .335 (10.0) .394 A (10.0) .394 (4.0) Max .157 (10.0) .394 (4.0) Max .157 (4.0) Max .157 (3.5) Min .138 (4.0) Max .157 (3.5) Min .138 Dimension A = Cap Height .091” (2.3mm) for Momentary with Plunger Code S .157” (4.0mm) for Alternate with Plunger Code S .142” (3.6mm) for Momentary & Alternate with Plunger Code L Operating Life 100,000 Boots for momentary devices are accompanied by a threaded adaptor which extends the length of the plunger. Operating Life 30,000 N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07