MB2411E1W13-FA

Series MB2400 Toggles Electrical Capacity (Resistive Load) Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons General Specifications Rockers Snap-Action Pushbuttons C Power Level (silver): Logic Level (gold): Logic/Power Level: (gold over silver) Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Travel Materials & Finishes Plunger: Bushing: Frame: Case: Base: Movable Contactor: Movable Contacts: Stationary Contacts: Terminals: Supplement Accessories Indicators Touch Tilt Tactiles Environmental Data Operating Temp Range: Humidity: Vibration: Shock: Installation Mounting Torque: Cap Installation Force: Soldering: Cleaning: 3A @ 125V AC 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Combines silver & gold ratings Note: Find additional explanation of dual rating & operating range in Supplement section. 20 milliohms maximum for silver; 30 milliohms maximum for gold 1,000 megohms minimum @ 500V DC 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts & case for 1 minute minimum 200,000 operations minimum 25,000 operations minimum for silver; 100,000 operations minimum for gold Single pole 2.45N; double pole 3.92N Pretravel .024” (0.6mm); Overtravel .016” (0.4mm); Total Travel .039” (1.0mm) Brass with nickel plating Brass with nickel plating Stainless steel Polybutylene terephthalate (PBT) (UL94V-0) Diallyl phthalate resin (UL94V-0) Phosphor bronze with silver or gold plating Silver alloy (code W); copper with gold plating (code G); or silver alloy with gold plating (code A) Silver alloy with silver plating (code W); copper or brass with gold plating (code G); or silver with gold plating (code A) Copper or brass with silver plating; copper or brass with gold plating –30°C through +85°C (–22°F through +185°F) 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 3 shocks in each direction) 1.5Nm (13.0 lb • in) for double nut; 0.7Nm (6.0 lb • in) for single nut 80.0N (18.0 lbf) maximum downward force on actuator Wave Soldering (PC version): See Profile B in Supplement section. Manual Soldering: See Profile B in Supplement section. These devices are not process sealed. Hand clean locally using alcohol based solution. See Cleaning Specifications in Supplement section. Standards & Certifications Flammability Standards: UL94V-0 case & base UL: File No. E44145 - Recognized only when ordered with marking on switch. Add “/U” or “/CUL” before dash in part number to order UL recognized switch. All single and double pole models recognized at 3A @ 125V AC or 0.4VA max. @ 28V DC max. CSA: File No. 023535_0_000 - Certified only when ordered with marking on switch. Add “/C” before dash in part number to order CSA certified switch. Single pole models with PC, solder lug, or Wirewrap terminals & double pole with PC or Wirewrap terminals certified at 3A @ 125V AC or 0.4VA @ 28V maximum. C96 www.nkkswitches.com Toggles Series MB2400 Rockers Distinctive Characteristics Snap-acting mechanism gives smooth actuation, short stroke, light touch, and audible feedback. This mechanism also provides long mechanical life. C Programmable Illuminated PB High torque bushing construction prevents rotation or separation from frame during installation. Pushbuttons Snap-Action Pushbuttons Antijamming design protects contacts from damage due to excessive downward force on the actuator. Keylocks Compatible companions with M series toggles. Body, bushing, and footprint dimensions ideal for mounting MB2400 pushbuttons and M toggles next to one another. Stainless steel frame resists corrosion. Rotaries Longer center solder lug terminal simplifies wiring and soldering. Slides Silver contacts of specially composed alloy for hardness. Tactiles Epoxy sealed terminals prevent entry of solder flux and other contaminants. Tilt Prominent external insulating barriers increase insulation resistance and dielectric strength. Page C98 Bracket PC Mount Page C102 Snap-in Mount Page C108 Accessories Indicators Touch Bushing Mount www.nkkswitches.com C97 Supplement Actual Size Toggles Series MB2400 TYPICAL SWITCH ORDERING EXAMPLE Rockers Pushbuttons Programmable Illuminated PB Keylocks Rotaries 11 MB24 C A2 Poles & Circuits 11 61 SPDT DPDT ON ON G 40 Contact Materials & Ratings (ON) (ON) Bushings F Caps W Silver Rated 3A @ 125V AC G Gold Rated 0.4VA max @ 28V AC/DC max A Gold over Silver Rated 3A @ 125V AC & 0.4VA max @ 28V AC/DC max ( ) = Momentary F .201” (5.1mm) Dia. H .295” (7.5mm) Dia. Cap Colors A Black B White C Red A2 .280” (7.1mm) Smooth with Keyway A1 .280” (7.1mm) Threaded with Keyway E2 .285” (7.24mm) Smooth with D Flat E1 .285” (7.24mm) Threaded with D Flat 13 .250” (6.35mm) Straight PC with .465” (11.8mm) Bracket .350” (8.9mm) Smooth with Keyway 15 .425” (10.8mm) Straight PC with .630” (16.0mm) Bracket S2 17 .964” (24.5mm) Straight PC with 1.150” (29.2mm) Bracket S1 .350” (8.9mm) Threaded with Keyway Terminals With Bracket With Reinforced Bracket Tactiles Slides Snap-Action Bracket PC Mount Pushbuttons 23 .250” (6.35mm) Straight PC with .465” (11.8mm) Bracket 25 .425” (10.8mm) Straight PC with .630” (16.0mm) Bracket 26 .750” (19.05mm) Straight PC with .953” (24.2mm) Bracket 30 Right Angle PC 40 Vertical PC Tilt With Terminal Support IMPORTANT: Indicators Touch Switches are supplied without UL, cULus & CSA marking unless specified. UL, cULus & CSA recognized only when ordered with marking on the switch. Specific models, ratings, & ordering instructions are noted on the General Specifications page. DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Accessories MB2411A2G40-FA SPDT ON-(ON) Circuit Supplement .280” (7.1mm) Smooth Bushing with Keyway Black .201” (5.1mm) Diameter Cap C102 Vertical PC Terminals Gold Contacts with 0.4VA Rating www.nkkswitches.com A Series MB2400 Toggles Snap-Action Bracket PC Mount Pushbuttons POLES & CIRCUITS Down Note: Terminal numbers are not actually on the switch. Pole Model SP MB2411 ON (ON) 1-3 1-2 SPDT DP MB2461 ON (ON) 1-3 4-6 1-2 4-5 DPDT Keyway Keyway C 1 (COM) 2 3 2 Programmable Illuminated PB 3 1 (COM) 4 5 6 BUSHINGS (0.8) .031 (8.0) Dia .315 (0.9) .035 .280” (7.1mm) Threaded with Keyway (5.54) (7.24) .218 .285 E1 (8.0) Dia .315 Maximum Panel Thickness with Standard Hardware: .068” (1.74mm) Rotaries (2.5) .098 (0.9) .035 Maximum Panel Thickness with Standard Hardware: .068” (1.74mm) (0.9) .035 1/4-40 Thd (2.84) Dia .112 (8.0) Dia .315 (5.54) (7.24) .218 .285 (8.9) .350 .350” (8.9mm) Threaded with Keyway (0.8) .031 (2.5) .098 (0.9) .035 (5.54) .218 S1 1/4-40 Thd (2.84) Dia .112 (2.5) .098 (2.5) .098 (0.9) .035 .285” (7.24mm) Threaded with D Flat 1/4-40 Thd (2.84) Dia .112 (5.54) (7.1) .218 .280 (8.0) Dia .315 (2.5) .098 Tactiles (5.54) (7.1) .218 .280 (6.2) Dia .244 (2.84) Dia .112 (0.8) .031 Tilt (8.0) Dia .315 .350” (8.9mm) Smooth with Keyway S2 (6.2) Dia .244 (2.84) Dia .112 (2.5) .098 A1 .285” (7.24mm) Smooth with D Flat (6.2) Dia .244 (2.84) Dia .112 (0.8) .031 (8.0) Dia .315 E2 (5.54) .218 (8.9) .350 (0.9) .035 Maximum Panel Thickness with Standard Hardware: .134” (3.40mm) Indicators .280” (7.1mm) Smooth with Keyway Keylocks Note: Plunger selection is not required for MB2400 pushbuttons. The plunger can be used with or without a cap. A2 Panel Cutouts (5.8) .228 (0.6) .024 (6.5) Dia .256 With Optional Locking Ring (5.8) .228 Standard hardware includes 2 hex nuts & 1 lockwasher. Hardware is illustrated following the Typical Switch Dimension drawings. www.nkkswitches.com (6.5) Dia .256 (2.2) Dia .087 Accessories (6.5) Dia .256 For E1 or E2 Bushing with D Flat (6.1) .240 Supplement For A1, A2, S1, or S2 Bushing with Keyway Rockers Normal Pushbuttons Down Throw & Switch Schematics Slides Normal Connected Terminals Touch Plunger Position ( ) = Momentary C103 Toggles Series MB2400 Keylocks Programmable Illuminated PB Pushbuttons Rockers CONTACT MATERIALS & RATINGS W Silver over Silver Power Level 3A @ 125V AC G Gold over Brass or Copper Logic Level 0.4VA maximum @ 28V AC/DC maximum Note: Complete explanation of operating range in Supplement section. C A Power Level or Logic Level Gold over Silver 3A @ 125V AC or 0.4VA maximum @ 28V AC/DC maximum Note: This dual rated option is suitable when two or more identical switches are used in logic and in power circuits within the same application. See Supplement section for complete explanation of dual rating and operating range. TERMINALS Straight PC Mount with Bracket 13 Straight PC Mount with Reinforced Bracket 15 .250” (6.35mm) Terminal with .465” (11.8mm) Bracket 17 .425” (10.8mm) Terminal with .630” (16.0mm) Bracket 23 .964” (24.5mm) Terminal with 1.150” (29.2mm) Bracket 25 .250” (6.35mm) Terminal with .465” (11.8mm) Bracket 26 .750” (19.05mm) Terminal with .953” (24.2mm) Bracket .425” (10.8mm) Terminal with .630” (16.0mm) Bracket Tactiles Slides Rotaries Snap-Action Bracket PC Mount Pushbuttons 40 Right Angle PC Vertical PC Tilt 30 CAPS & CAP COLORS F AT475 .201” (5.1mm) Diameter Cap (5.1) Dia .201 (6.4) .253 H (4.0) .157 AT496 .295” (7.5mm) Diameter Cap Material: Polyamide Material: Polyamide Finish: Glossy Finish: Glossy Supplement Accessories Indicators Touch PCB footprints are on the following Typical Switch Dimension pages. Cap Colors Available: C104 A Black B www.nkkswitches.com White (7.5) Dia .295 (6.4) .253 C Red (4.0) .157 Toggles Series MB2400 Snap-Action Bracket PC Mount Pushbuttons TYPICAL SWITCH DIMENSIONS (0.9) .035 Double Pole B R AC KE T LE N GT H (0.5) Typ .020 (0.8) Typ .031 (4.7) Typ .185 (4.5) Typ .177 (1.17) Typ .046 (1.17) Typ .046 (4.8) Typ .189 (3.2) Typ .126 MB2411A2G13-FA (12.7) .500 (8.0) .315 (15.8) .622 (1.6) Typ .063 (2.4) Typ .095 (1.6) Typ .063 3 (7.9) Typ .311 (7.9) Typ .311 2 (4.7) Typ .185 (4.7) Typ .185 1 (1.8) Dia Typ .073 (1.5) Dia Typ .059 (1.8) Dia Typ .073 (1.5) Dia Typ .059 C (4.8) Typ .189 3 6 2 5 1 4 CL Terminal Code: Terminal Length: Bracket Length: 13 .250 (6.35mm) .465 (11.8mm) 15 .425 (10.8mm) .630 (16.0mm) 17 .964 (24.5mm) 1.150 (29.2mm) (6.4) .253 (5.1) Dia Typ .201 (2.8) Dia Typ .112 (6.2) Dia Typ .244 Single Pole (2.4) .096 Straight PC • Reinforced Bracket (0.9) .035 Double Pole 2 NO (0.5) Typ .020 (0.8) Typ .031 (4.7) Typ .185 3 NC (4.5) Typ .177 (4.8) Typ .189 (1.27) Typ .050 (1.17) Typ .046 (6.35) Typ .250 (4.8) Typ .189 (19.05) .750 (2.4) Typ .095 (3.18) Typ .125 (3.18) Typ .125 (9.53) Typ .375 3 (9.53) Typ .375 2 (4.7) Typ .185 (1.8) Dia Typ .073 (1.5) Dia Typ .059 (12.7) .500 (9.1) .358 1 (4.7) Typ .185 (1.8) Dia Typ .073 (1.5) Dia Typ .059 Touch 1 C MB2411A2G23-FA Indicators TERMIN A L LEN G T H Tilt B R AC KE T LE N GT H 3 6 2 5 1 4 CL Terminal Code: Terminal Length: Bracket Length: 23 .250 (6.35mm) .465 (11.8mm) 25 .425 (10.8mm) .630 (16.0mm) 26 .750 (19.05mm) .953 (24.2mm) www.nkkswitches.com Accessories (7.1) .280 Programmable Illuminated PB 3 NC Keylocks 2 NO Rotaries 1 C Tactiles T ERMIN A L LEN G T H Pushbuttons Single Pole (2.4) .096 Supplement (7.1) .280 Slides (6.4) .253 Straight PC • Bracket (5.1) Dia Typ .201 (2.8) Dia Typ .112 (6.2) Dia Typ .244 Rockers C105 Toggles Series MB2400 Snap-Action Bracket PC Mount Pushbuttons TYPICAL SWITCH DIMENSIONS Single Pole (4.7) Typ .185 COM NO NC C (2.9) .114 (5.08) .200 (1.4) Typ .055 (7.9) .311 (6.22) .245 (2.4) .096 (13.0) .512 (6.4) .253 (7.32) .288 1 2 (12.7) .500 (4.3) .169 (0.4) .016 (12.7) .500 1 3 (0.8) Typ .031 (4.7) Typ .185 (1.27) .050 (1.8) Dia Typ .073 (2.54) Typ .100 MB2411A2G30-FA Right Angle PC Double Pole (2.84) Dia .112 (6.2) Dia .244 Keyway COM NO NC (2.9) .114 (5.08) .200 (1.4) Typ .055 (6.2) .245 (2.4) .096 (6.4) .253 (13.0) .512 4 (12.7) .500 (5.1) Dia .201 (7.32) .288 5 (4.7) Typ (3.81) .185 6 .150 6 3 1 2 4 2 1 (12.7) .500 (4.3) .169 (0.4) .016 (12.7) .500 5 3 (0.8) Typ .031 (4.7) Typ .185 (1.27) Typ .050 (3.8) .150 (1.8) Dia Typ .073 (2.54) Typ .100 MB2461A2G30-FA Vertical PC Single Pole 3 Tilt NC (2.84) Dia .112 (6.2) Dia .244 Keyway Touch Indicators (1.4) Typ .055 (5.08) .200 (2.4) .096 (6.2) .245 (6.4) .253 (7.32) .288 (0.4) .016 (12.7) .500 2 COM 1 Supplement www.nkkswitches.com (1.27) .050 (2.7) .106 (0.8) Typ .031 (3.8) Typ .150 (1.8) Dia Typ .073 (2.54) Typ .100 (2.4) Typ .094 6 3 NO 5 2 COM 4 1 MB2411A2G40-FA C106 (12.7) .500 (8.0) .315 Double Pole 2 1 (13.0) .512 (5.1) Dia .201 (3.81) Typ .150 3 NO NC Accessories 2 3 (5.1) Dia .201 Rotaries Slides Tactiles (2.84) Dia .112 (6.2) Dia .244 Keyway Keylocks Programmable Illuminated PB Pushbuttons Rockers Right Angle PC (4.8) .189 (12.7) .500 (3.81) Typ .150 (1.27) Typ .050 (12.7) .500 (1.8) Dia Typ .073 (2.54) Typ .100 3 6 2 5 1 4 Series MB2400 Toggles Snap-Action Bracket PC Mount Pushbuttons HARDWARE Standard Hardware (6.4) Dia (10.2) Dia .252 .402 1 included with each switch Material: Brass with Nickel Plating (9.0) .354 (1.5) .059 Material: Steel with Zinc/Chromate C (0.5) .020 Programmable Illuminated PB 2 included with each switch AT509 Lockwasher Optional Hardware (12.0) Dia .472 Material: Steel with Zinc/Chromate (5.8) .229 (1.68) .066 (0.8) .031 Tilt Tactiles Slides Rotaries (0.8) .031 (12.0) Dia .472 Touch (1.7) .067 (2.0) .079 (5.5) .217 Indicators Material: Steel with Zinc/Chromate (6.2) Dia .244 Accessories (2.0) .079 AT515 Locking Ring for E1 Bushing Keylocks (6.35) Dia .250 Supplement AT507H Locking Ring for A1 or S1 Bushing Pushbuttons (8.0) .315 Rockers 1/4-40 Thd AT513H Inch Threaded Hexagon Nut www.nkkswitches.com C107