MRB14B-AA

Miniature PCB Process Sealed Rotaries Series MRB Distinctive Characteristics Double flatted bushing prevents rotation in panel and increases stability. Totally sealed construction, achieved with combination of an interior o-ring, a seal between the frame and base, plus insert molded terminals, prevents contact contamination and allows automated soldering and cleaning. Positive detent mechanism for distinct feel and audible feedback. Break-before-make contact timing with sliding contact mechanism. Metal bushing and frame/bracket provide durability. Panel seal, achieved with use of optional exterior o-ring, conforms to IP67 of IEC60529 Standards. High contact reliability achieved by the self-cleaning contact mechanism. .100” x .100” (2.54mm x 2.54mm) terminal spacing conforms to standard PC board grid spacing for straight and right angle mounting. Actual Size Insert molded terminals lock out flux and other contaminants. N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Miniature PCB Process Sealed Rotaries Series MRB General Specifications Electrical Capacity (Resistive Load) Logic Level: 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Note: See Supplement Index to find explanation of operating range. Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Operating Torque: Contact Timing: Indexing: 80 milliohms maximum 100 megohms minimum @ 500V DC 500V AC minimum for 1 minute minimum 30,000 operations minimum 10,000 operations minimum 0.04Nm average Nonshorting (break-before-make) 45° for On-On-On & 90° for On-None-On Materials & Finishes Shaft: Bushing: Frame/Bracket: Movable Contacts: Stationary Contacts: Terminals: Base: Brass with nickel plating Zinc alloy with nickel plating Steel with tin plating Beryllium copper spring with gold plating Copper with gold plating Brass with tin plating Polyamide Environmental Data Operating Temperature Range: Humidity: Vibration: Shock: –10°C through +70°C (+14°F through +158°F) 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 3 right angled directions, with 5 shocks in each direction) Installation Mounting Torque: Cap Installation Force: .686Nm (6.08 l b • in) 19.6 ~ 29.4N (4.41 ~ 6.61 lbf) PCB Processing Soldering: Cleaning: Wave Soldering Recommended: See Profile B in Supplement section Manual Soldering: See Profile B in Supplement section Automated cleaning. See Cleaning specifications in Supplement section. Standards & Certifications UL Recognition or CSA Certification: The MRB Series rotaries have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy. N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Miniature PCB Process Sealed Rotaries TYPICAL SWITCH ORDERING EXAMPLE Series MRB MRB POLES 1 2 SPDT SP3T DPDT DP3T 1 B H 2 TERMINALS Straight with Bracket Right Angle with Bracket B KNOBS A B C Plain Black A COLORS For Plain Knob No Code A B C E F G H Black Small Color Tipped Large Color Tipped For Color Tipped Black White Red Yellow Green Blue Gray CIRCUITS & INDEXING 2 4 ON ON NONE ON ON ON 90° 45° DESCRIPTION FOR TYPICAL ORDERING EXAMPLE MRB12B-A Plain Black Knob SPDT with ON-NONE-ON Circuit & 90° Indexing Straight PC Terminals with Bracket P OLES & CIRCUITS Actuator Positions Pole Model MRB12 SP MRB14 ON ON ON C1-1 C1-2 C1-3 SP3T 123 Connected Terminals Position 1 C1-1 Position 2 OPEN Position 3 C1-2 Throw & Schematics Note: Terminal numbers are not actually on switch C1 Position 1 ON Position 2 NONE Position 3 ON SPDT 1 2 C1 C1 C2 MRB22 DP MRB24 ON NONE ON C1-1 C2-4 OPEN C1-2 C2-5 DPDT 1 2 C1 4 5 C2 ON ON ON C1-1 C2-4 C1-2 C2-5 C1-3 C2-6 DP3T 123 456 TERMINALS B Straight PC Terminals with Bracket H Right Angle PC Terminals with Bracket SPDT DPDT N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Miniature PCB Process Sealed Rotaries TYPICAL SWITCH DIMENSIONS 90° Indexing • SPDT & DPDT • Straight PC 90° POS 1 POS 3 M6 P0.75 (0.5) Typ .020 (2.54) .100 Series MRB (0.7) Dia Typ .028 1 2 4 5 4 1 2 (2.54) Typ .100 5 (2.28) .090 (3.1) Dia .122 Keyway (14.5) .571 (10.0) .394 (7.0) .276 (11.0) .433 (5.08) .200 (15.74) .620 C1 C2 C2 C1 (5.08) .200 (1.0) Dia Typ .039 (2.54) Typ .100 (3.5) .138 (0.7) Typ .028 (10.16) .400 (10.16) .400 MRB12B Actuator shown in Position 1 Single pole model does not have terminals 4, 5 & C2 90° Indexing • SPDT • Right Angle PC (2.28) .090 POS 1 Double Flat with M6 P0.75 (15.74) .620 (2.54) .100 C1 2 1 90° Keyway POS 3 (3.1) Dia .122 (0.5) Typ .020 (10.0) .394 (7.0) .276 (0.7) Typ .028 (9.4) .370 1 2 C1 (9.0) .354 (16.3) .642 (5.08) .200 (2.54) Typ .100 (2.54) .100 (7.62) .300 (15.24) .600 (7.62) .300 (2.54) .100 (2.54) Typ .100 (2.54) .100 (3.5) (0.7) Dia Typ .138 .028 (5.08) .200 C L (1.0) Dia Typ .039 MRB12H Actuator shown in Position 1 90° Indexing • DPDT • Right Angle PC (2.28) .090 POS 1 Double Flat with M6 P0.75 (15.74) .620 4 5 C2 90° Keyway POS 3 (3.1) Dia .122 (0.5) Typ .020 (10.0) .394 (7.0) .276 (0.7) Typ .028 (9.4) .370 1 2 C1 (9.0) .354 (16.3) .642 (5.08) .200 (2.54) .100 C2 C1 5 2 4 1 (2.54) Typ .100 (2.54) .100 (7.62) .300 C L (1.0) Dia Typ .039 (15.24) .600 (7.62) .300 (2.54) .100 (2.54) .100 (2.54) Typ .100 (2.54) .100 (3.5) (0.7) Dia Typ .138 .028 (5.08) .200 MRB22H Actuator shown in Position 1 45° Indexing • SP3T & DP3T • Straight PC POS 2 POS 1 45° 45° POS 3 M6 P0.75 (0.5) Typ .020 (2.54) Typ .100 1 2 (0.7) Dia Typ .028 4 5 6 C2 4 5 1 2 3 C1 (2.54) Typ .100 (2.28) .090 (3.1) Dia .122 Keyway (14.5) .571 (10.0) .394 (7.0) .276 (11.0) .433 (5.08) .200 3 C1 (15.74) .620 6 C2 (5.08) .200 (1.0) Dia Typ .039 (2.54) Typ .100 (3.5) .138 (10.16) .400 (0.7) Typ .028 (10.16) .400 MRB14B Actuator shown in Position 1 Single pole model does not have terminals 4, 5, 6 & C2 03-07 N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com Miniature PCB Process Sealed Rotaries TYPICAL SWITCH DIMENSIONS 45° Indexing • SP3T • Right Angle PC (2.28) .090 POS 1 45° POS 2 45° Keyway POS 3 (3.1) Dia .122 (0.5) Typ .020 (7.0) .276 (0.7) Typ .028 (9.4) .370 1 2 3 C1 Series MRB Double Flat with M6 P0.75 (15.74) .620 (9.0) .354 (16.3) .642 (2.54) Typ .100 (5.08) .200 C1 3 2 1 (2.54) Typ .100 (2.54) .100 (7.62) .300 (15.24) .600 (10.0) .394 (7.62) .300 (2.54) Typ .100 (2.54) (2.54) Typ .100 .100 (3.5) (0.7) Dia Typ .138 .028 (5.08) .200 C L (1.0) Dia Typ .039 MRB14H Actuator shown in Position 1 45° Indexing • DP3T • Right Angle PC (2.28) .090 POS 1 45° POS 2 45° Keyway POS 3 (3.1) Dia .122 (0.5) Typ .020 (7.0) .276 (0.7) Typ .028 (9.4) .370 1 2 3 C1 Double Flat with M6 P0.75 (15.74) .620 4 5 6 C2 (9.0) .354 (16.3) .642 (2.54) Typ .100 (5.08) .200 C2 C1 (2.54) Typ .100 6 3 5 2 4 1 (2.54) .100 (7.62) .300 (15.24) .600 (10.0) .394 (7.62) .300 (2.54) (2.54) Typ .100 .100 (2.54) Typ (2.54) .100 .100 (3.5) (0.7) Dia Typ .138 .028 (5.08) .200 C L (1.0) Dia Typ .039 MRB24H Actuator shown in Position 1 KNOBS A AT433 Plain Black B (19.0) Dia .748 (11.0) Dia .433 AT4103 Small Color Tipped Material: Polyacetal Color: Black (13.0) .512 Polyester Base: Black (9.5) .374 (16.0) Dia .630 (9.5) Dia .374 C AT4104 Large Color Tipped (18.0) Dia .709 (11.0) Dia .433 (0.5) .020 Polyamide Tip Colors: A, B, C, E, F, G, H (14.3) .563 Polyester Base: Black (9.5) .374 (15.8) .622 (0.5) .020 Polyamide Tip Colors: A, B, C, E, F, G, H (9.5) .374 (0.5) .020 Color Codes: Shaft Detail (2.28) .090 (10.0) .394 (3.1) Dia .122 (1.0) .039 A Black B White C Red E Yellow F Green G Blue H Gray Mounting Precaution for Cap Clearance on Right Angle Models When mounting a right angle switch, a cap clearrance of .035” (0.9mm) is recommended. Interruption by end of PCB (0.9) .035 PCB Standard Hardware Supplied AT513M Hex Nut AT507M Locking Ring AT509 Lockwasher Optional Hardware AT535 O-ring for Panel Seal See Supplement for details PANEL CUTOUTS & MAXIMUM EFFECTIVE PANEL THICKNESS With Standard Hardware .087” (2.2mm) (6.5) .256 (6.35) Dia .250 (2.2) Dia .087 Without Locking Ring .118” (3.0mm) (6.35) Dia .250 (5.6) .220 (0.6) .024 Sealed Panel with 2 Hex Nuts & 1 Rubber O-ring .165” (4.2mm) (6.2) Dia .244 (5.4) .213 N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07