MRK112-BF

Toggles Series MR Rockers General Specifications Electrical Capacity (Resistive Load) For MRA: 250mA @ 125V AC Pushbuttons For MRF or MRK: Programmable Illuminated PB Other Ratings Slides Rotaries Keylocks Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Range of Operating Torque: Contact Timing: Indexing: Materials & Finishes G Shaft: Stopper Plate: Bushing/Housing: Movable Contacts: End Contacts & Terminals: Common Contacts & Terminals: Base: Tilt Tactiles Environmental Data Operating Temperature Range: Humidity: Vibration: Shock: Sealing: Touch Installation Mounting Torque: Cap Installation Force: Accessories Indicators Processing Supplement Half-Inch Diameter Process Sealed Rotaries Soldering Time & Temperature: Cleaning: Standards & Certifications G16 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Note: Find additional explanation of operating range in Supplement section. 10 milliohms maximum for MRA; 50 milliohms maximum for MRF & MRK 100 megohms minimum @ 500V DC 1,000V AC minimum for 1 minute minimum for MRA 500V AC minimum for 1 minute minimum for MRF & MRK 30,000 operations minimum 10,000 operations minimum 0.02 ~ 0.07Nm for MRA; 0.005 ~ 0.02Nm for MRF & MRK Nonshorting (break-before-make) MRA – self-cleaning, sliding contact; MRF & MRK – self-cleaning, rotary contactor disk 30° Brass with nickel plating Steel with zinc plating for MRA & MRK; polyamide cover with stopper for MRF Zinc alloy with zinc plating Copper with silver plating for MRA; phosphor bronze with gold plating for MRF & MRK Brass with silver plating for MRA; phosphor bronze with gold plating for MRF & MRK Brass with silver plating for MRA; phosphor bronze with gold plating for MRF & MRK Diallyl phthalate for MRA; fiberglass reinforced polyamide for MRF & MRK –10°C through +70°C (+14°F through +158°F) 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 3 right angled directions, with 3 shocks in each direction) MRK model meets IP67 of IEC60529 standards .686Nm (6.08 l b • in) 19.6 ~ 29.4N (4.41 ~ 6.61 lbf) for MRA & MRK Wave Soldering for MRA: See Profile A in Supplement section. Wave Soldering for MRF & MRK: See Profile B in Supplement section. Manual Soldering for MRA: See Profile A in Supplement section. Manual Soldering for MRF & MRK: See Profile B in Supplement section. Automated cleaning recommended. Stopper plate, as well as washers for MRA & MRK, must be in place to maintain automated cleaning. See Cleaning specifications in Supplement section. MRA, MRF, & MRK models have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy. www.nkkswitches.com Toggles Series MR Rockers Distinctive Characteristics Programmable Illuminated PB Pushbuttons Low profile body of MRF model accommodates space limitations required for PCB mounting. For the MRA and MRK bushing mount models, the range of behind panel body depths is .323” to .669” (8.2mm to 17.0mm). Positive detent mechanism for distinct feel and audible feedback. Metal bushing and housing construction increases durability. Keylocks Adjustable stopper plate allows 2–12 position settings. High contact reliability achieved by the self-cleaning contact mechanism. G Slides Break-before-make contact timing with sliding contacts in MRA and rotary contactor disk in MRF and MRK models. Rotaries Half-Inch Diameter Process Sealed Rotaries Tactiles Interior housing seal and molded-in PC terminals, plus shaft rubber o-ring on MRA and MRK and polyamide cover on MRF model, allow cleaning after automated soldering. Tilt MRK model meets IP67 of IEC60529 specifications (similar to NEMA 4 & 13). Supplement Accessories Indicators Touch Actual Size www.nkkswitches.com G17 Series MR Toggles Half-Inch Diameter Process Sealed Rotaries TYPICAL SWITCH ORDERING EXAMPLE Pushbuttons Rockers MR A 206 Poles & Circuits Rotaries Knobs Colors A Shaft Actuated with PC Terminals 112 SP with 2-12 Positions A Plain Black F Low Profile Screwdriver Actuated with PC Terminals 206 DP with 2-6 Positions B Small Color Tipped 4P with 2-3 Positions C Large Color Tipped K Low Profile Shaft Actuated with PC Terminals 403 For Plain Knob No Code Black For Color Tipped A Black B White C Red DESCRIPTION FOR TYPICAL ORDERING EXAMPLE E Yellow MRA206-A F Green G Blue H Gray Keylocks Programmable Illuminated PB Actuators & Terminals A Shaft Actuated with Plain Black Knob G Slides DP with 2-6 Adjustable Positions Tactiles PC Terminals Tilt ACTUATORS & TERMINALS Shaft Actuated with PC Terminals Low Profile Screwdriver Actuated with PC Terminals F Low Profile Shaft Actuated with PC Terminals K 10 12 11 10 Accessories 1 Supplement (10.0) .394 G18 Shaft 6 4 5 1 23 (3.1) .122 (2.28) .090 2 (3.5) .138 (0.5) .020 Thk = (0.25) .010 Terminal 1C 89 2 12 11 10 11 9 12 7 Indicators Touch A M R- 12 2 12 11 10 (3.5) .138 (0.8) .031 (3.15) Dia .124 (1.0) .039 Slotted for Screwdriver www.nkkswitches.com (0.5) .020 Thk = (0.25) .010 Terminal 11 10 9 M R - K 1 1 29 1 C 12 11 10 (3.1) .122 (2.28) .090 (10.0) .394 Shaft (3.5) .138 (0.5) .020 Thk = (0.25) .010 Terminal Series MR Toggles Half-Inch Diameter Process Sealed Rotaries POLES & CIRCUITS 4P Number of Terminals MRA112 2–12 2, 3, 4, . . . 12 1 COM, 12 LOAD MRF112 2–12 2, 3, 4, . . . 12 1 COM, 12 LOAD MRK112 2–12 2, 3, 4, . . . 12 1 COM, 12 LOAD MRA206 2–6 2, 3, 4, 5, 6 2 COM, 12 LOAD MRF206 2–6 2, 3, 4, 5, 6 2 COM, 12 LOAD MRK206 2–6 2, 3, 4, 5, 6 2 COM, 12 LOAD MRA403 2–3 2, 3 4 COM, 12 LOAD MRF403 2–3 2, 3 4 COM, 12 LOAD MRK403 2–3 2, 3 4 COM, 12 LOAD Schematics A Rockers Stopper Settings 1 2 3 4 5 6 7 8 9 10 11 12 A 1 B 2 3 4 5 6 A 1 1 2 3 4 5 C B 2 3 1 2 3 1 Pushbuttons DP Number of Positions 6 Programmable Illuminated PB SP Model D 2 3 1 2 3 POSITION SETTING FOR MRA, MRF, & MRK MODELS MRF Models Protective Cover Remove the protective cover from the switch body. Turn the shaft counterclockwise to the extreme left by using a screwdriver. Inside the cover is a magnifying lens which would be positioned over the number which is to be the maximum position used; when the cover is then snapped into the switch, the projection beside the lens fits into the correct hole for setting the stop. 23 12 1C MR - 12 11 10 Slides 2 Projection 10 11 1 6 4 5 89 MRK & MRA Models G Lens 7 Using the actuator knob, turn the shaft counterclockwise to the extreme left. If the shaft is not turned counterclockwise to the extreme left, proper setting cannot be achieved. At this extreme position, the white line on the knob points to the number 1 position shown on the side of the switch. 2. Remove the knob from the shaft and loosen the nut far enough to allow raising the stopper plate, plus washer(s), for resetting to the desired position. Factory Assembled: 3. Note the position numbers on the side of the switch; these correspond to the terminal numbers and stopper holes. Insert the stopper in the hole numbered for the maximum desired number of stop settings. Satisfactory switch functioning cannot be assured if the stopper plate is not properly positioned. Metal Washer (MRA) Tactiles Standard Mounting Hardware Packaged Loose with Each Switch: 1. Hex Face Nut Tilt Locking Ring Lockwasher Touch Rubber Ring (MRK) Hex Nut Indicators Stopper Plate 12 2 11 10 9 9 12 M R - K 1 1 29 1 C Accessories Rubber Washer 11 10 12 11 10 2 1 4. Tighten the nut (beveled side up) firmly against the stopper plate. www.nkkswitches.com 12 11 10 Supplement 1. 2. 3. Keylocks Each switch is supplied with the stopper set for the maximum number of positions allowed for that model. Prior to installation, the desired position setting should be made. Contact factory for continuous rotation. Rotaries Pole G19 Series MR Toggles Half-Inch Diameter Process Sealed Rotaries TYPICAL SWITCH DIMENSIONS 3 3 2 3 2 1 C A 3 4 5 6 7 8 4 5 2 Pushbuttons 1 2 1 (6.0) .236 (10.0) .394 (16.0) Dia .630 (17.0) .669 (5.0) .197 p 30° Ty (9.5) Dia .374 (10.0) .394 30° Ty (9.5) Dia .374 p 30° Ty (9.5) Dia .374 p MRA112 MRF • PC Terminals 3 B D C 4 3 5 6 3 3 21 21 4 21 21 5 1 10 6 30° B 3 21 30° 3 3 21 1 A 2 1 A 12 1 2 (8.2) .323 (14.0) Dia .551 6 yp 15° T (0.5) Typ .020 (3.5) .138 (4.2) .165 7 30° 8 ° 15 ° 15 ° 15 9 (12.0) Dia .472 5 3 4 5 4 Pole (0.25) Typ .010 Cover 6 7 8 G 2 Pole 4 Keylocks (0.8) .031 1 Pole A 2 1 yp 15° T yp 15° T (12.6) Dia .496 (12.6) Dia .496 (12.6) Dia .496 1 Pole 3 D 2 1 4 65 1 10 21 3 A 2 1 A 2 1 Tactiles 3 C 2 1 p B 2 1 Typ 3 4 1 Tilt 15° 30° 5 y 15° T yp 15° T yp 15° T (12.6) Dia .496 (12.6) Dia .496 (3.5) .138 6 (10.1) .398 B 2 1 3 (5.5) .217 (10.0) .394 6 4 (0.5) Typ .020 (3.1) .122 7 5 (2.28) .090 Keyway 8 30° 9 (12.0) Dia .472 4 Pole ° 15 ° 15 (0.25) Typ .010 M6 P0.75 2 Pole 3 MRK • PC Terminals 1 A Slides MRF403 32 Programmable Illuminated PB 6 (1.0) .039 (3.1) .122 9 10 11 Rotaries 2 D 2 5 1 1 4 1 10 11 2 B 3 B 6 A (2.28) .090 Keyway (3.0) Dia .118 (3.0) Dia .118 3 9 12 A 1 Touch (3.0) Dia .118 (0.8) Dia Typ .031 M6 P0.75 3 Rockers MRA • PC Terminals 1 Pole 2 Pole 4 Pole (12.6) Dia .496 MRK devices are designed to be panel mounted. Installation without panel mounting will affect reliability. MRK112 9 10 11 2 30 ° Typ G20 1 12 (1.0) Dia Typ .039 B 4 4 A 5 3 2 30 ° Typ 1 1 3 3 5 (9.5) Dia .374 6 2 90° A 3 (9.5) Dia .374 6 2 2 3 B C 1 A 30° 1 D 3 2 (1.0) Dia Typ .039 (3.0) Typ .118 1 Typ 2 (9.5) Dia .374 7 6 5 8 B 9 10 4 3 (1.0) Dia Typ .039 (0.8) Dia Typ .031 3 11 12 2 1 A 15 ° Ty p www.nkkswitches.com (12.0) Dia .472 6 1 (0.8) Dia Typ .031 2 3 5 4 4 3 15 ° 6 2 1 A Typ Four Pole MRF403 MRK403 B p 8 1 (3.0) Typ .118 Double Pole MRF206 MRK206 Single Pole MRF112 MRK112 5 (12.0) Dia .472 15° Ty (3.0) Typ .118 Four Pole MRA403 30° Typ 6 5 4 Supplement 7 Double Pole MRA206 30° Typ Single Pole MRA112 180° Accessories Indicators FOOTPRINTS 2 1 C 3 (0.8) Dia Typ .031 1 2 3 D 1 2 3 3 15° 2 1 A Typ (12.0) Dia .472 Series MR Toggles Half-Inch Diameter Process Sealed Rotaries KNOBS Polyamide Tip Colors: A, B, C, E, F, G, H (9.5) .374 (0.5) .020 (0.5) .020 A Color Codes: B Black C White Rockers (15.8) .622 Pushbuttons (14.3) .563 (9.5) .374 Programmable Illuminated PB Polyamide Tip Colors: A, B, C, E, F, G, H (9.5) .374 (18.0) Dia .709 (11.0) Dia .433 (0.5) .020 E Red F Yellow Green G H Blue Gray MRA & MRK MRK Nonsealed Panel Sealed Panel Without Keyway With Keyway (6.35) Dia .250 (6.5) .256 (5.6) .220 (6.35) Dia .250 (2.2) Dia .087 With Standard Hardware on Nonsealed Panel: MRA .067” (1.7mm) MRK .087” (2.2mm) Without Locking Ring on Nonsealed Panel: MRA .098” (2.5mm) MRK .118” (3.0mm) (6.2) Dia .244 (0.6) .024 With AT513M & AT535 only on Sealed Panel: MRK .106” (2.7mm) (5.4) .213 AT513M Metric Hexagon Nut AT545 Locking Ring AT509 Lockwasher AT535 Rubber Ring Material: Brass, nickel plating 1 for MRA; 1 for MRK Material: Steel, chromate over zinc plating 1 for MRA; 1 for MRK Material: Steel, chromate over zinc plating 1 for MRA; 1 for MRK Material: Nitrile butadiene rubber 1 for MRK (6.0) .236 (8.0) .315 (6.2) Dia .244 (11.6) .457 (2.0) .079 (6.4) Dia (10.2) Dia .252 .402 Tilt M6 P0.75 (9.4) Dia .370 (1.7) .067 (0.5) .020 (0.8) .031 (1.3) .051 Indicators (1.5) .059 Touch (12.0) .472 (9.0) .354 OPTIONAL SUPPORT BRACKET AT543 Support Bracket for MRK Material: Steel with tin plating (18.0) .709 (18.0) .709 (17.5) .689 (14.9) .587 (3.8) Typ .150 (0.5) Typ .020 (14.0) .551 (0.8) Typ .031 G Slides STANDARD MOUNTING HARDWARE (5.5) .217 Keylocks PANEL CUTOUTS & MAXIMUM EFFECTIVE PANEL THICKNESS Rotaries (13.0) .512 Base Material: Polyester Base Color: Black (16.0) Dia .630 (9.5) Dia .374 Tactiles (19.0) Dia .748 (11.0) Dia .433 AT4104 Large Color Tipped C Base Material: Polyester Base Color: Black Material: Polyacetal Color: Black only AT4103 Small Color Tipped B (17.2) .677 (1.2) Dia Typ .047 www.nkkswitches.com A support bracket is needed when the MRK is mounted only to a PC board and does not have the bushing through a panel. G21 Accessories AT433 Plain Black Supplement A