ND3KC10P-R

8mm Process Sealed SMT DIP Rotaries Series ND3 Distinctive Characteristics Sealed construction prevents contact contamination and allows vapor phase and IR reflow soldering. Sealed design accomplished with seals between the actuator and housing and between housing and base. Highly visible legends and choice of screwdriver or shaft actuation to provide trouble-free code setting. Detent mechanism designed for crisp, positive action for accurate switch setting. Bifurcated, spring loaded contacts give unmatched logic-level reliability. Heat tolerant resin used for body meets UL flammability rating of 94V-0 and maintains switch reliability through vapor phase and infrared convection reflow soldering. Gull-winged terminals ensure mechanical stability during soldering and simplified solder joint inspection. .100” (2.54mm) terminal grid spacing between pin centers, plus 3-by-3 terminal arrangement for pad layout pattern equivalent to industry standard. Epoxy sealed terminals lock out flux, solvents, and other contaminants. Packaging in tape-reel or partitioned tray. Tape-reel packaging meets EIA-481-2 Standard. Coplanarity: all considered surfaces must lie between two parallel planes that are a maximum distance apart of .0059” (0.15mm). (Additional coplanarity details in Terms and Acronyms in the Supplement section.) Actual Size N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 11-07 8mm Process Sealed SMT DIP Rotaries Series ND3 General Specifications Electrical Capacity (Resistive Load) Switching Rating: Nonswitching Rating: 100mA @ 5V DC 100mA @ 50V DC Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Torque: Contact Timing: 80 milliohms maximum for circuit; 30 milliohms maximum for contact point 1,000 megohms minimum @ 250V DC 250V AC minimum for 1 minute minimum 20,000 detent operations minimum 20,000 detent operations minimum Note: A detent operation is one actuator position operation or stepping. 20,000 detent operations = 1,250 cycles for hexadecimal devices or 2,000 cycles for decimal devices. A cycle is one 360° rotation. .061 kgf/cm (.846 oz/in) Nonshorting (break-before-make) Materials & Finishes Actuator: Housing: O-ring: Base: Movable Contact: Stationary Contacts: Terminals: Glass fiber reinforced polyamide Glass fiber reinforced polyamide (UL94V-0) Nitrile butadiene rubber Glass fiber reinforced polyamide (UL94V-0) Beryllium copper with gold plating Brass with gold plating Brass with gold plating) Environmental Data Operating Temperature Range: Humidity: Vibration: Shock: –25°C through +85°C (–13°F through +185°F) 90 ~ 95% humidity for 100 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Processing Soldering: Cleaning: Reflow Soldering: See Profile B in Supplement section. Manual Soldering: See Profile B in Supplement section. Automated cleaning. See Cleaning Specifications in Supplement section. Standards & Certifications Flammability Standards: UL Recognition or CSA Certification: UL94V-0 rated housing & base The ND3 Series rotaries have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy. N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 11-07 8mm Process Sealed SMT DIP Rotaries T YPICAL SWITCH ORDERING EXAMPLE Series ND3 ND3 K C 16 B PACKAGING ACTUATORS F K Screwdriver Actuated Shaft Actuated 10 16 POSITIONS Decimal Hexadecimal R No Code Tape-Reel 500 Pieces/Reel Partitioned Tray CIRCUITS R C Real Coded (White Actuator) Complement Coded (Red Actuator) P B H TERMINALS Gull Wing for Upright Mount Gull Wing for Upright with Bracket Mount Gull Wing for Right Angle Mount DESCRIPTION FOR TYPICAL ORDERING EXAMPLE ND3KC16B Shaft Actuated Gull Wing Terminals for Upright with Bracket Mount Complement Coded Hexadecimal Positions ACTUATION F Screwdriver Actuated K 34 Shaft Actuated ND3 - FC 10P ND3 - KC 10B Actuators are fully rotational in either direction. N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 11-07 89 89 Actuator colors: White for real coded Red for complement coded Actuator colors: White for real coded Red for complement coded 12 0 0 12 34 6 57 6 57 8mm Process Sealed SMT DIP Rotaries T RUTH TABLES (CIRCUITS & POSITIONS) Terminal No. (Output) Real Coded Model Numbers: ND3FR, ND3KR Actuator Position x = ON Series ND3 Hexadecimal 10 Decimal 16 01234567890123456789ABCDEF 1 R 2 4 8 C Complement Coded Model Numbers: ND3FC, ND3KC 1 2 4 8 TYPICAL SWITCH DIMENSIONS Screwdriver Actuated • Upright (0.6) .024 01 (2.6) Dia .102 (0.25) Typ .010 2 C 1 1 C 2 (1.7) Typ .067 (0.3) .012 (8.12) .320 ND3FR10P Shaft Actuated • Upright (0.6) .024 EF0 1 2 (0.3) .012 (8.12) .320 (3.2) .126 (5.6) .220 ND3KC16P Screwdriver Actuated • Upright with Bracket (0.6) .024 01 23 (0.3) .012 (8.12) .320 (5.6) .220 ND3FR10B N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 456 (7.92) .312 9 78 78 9 (7.92) .312 CD AB 456 (7.92) .312 9 78 (10.0) .394 8 C 4 4 C 8 (7.6) .300 23 (0.4) .016 (5.6) .220 (0.5) Typ .020 (2.54) Typ .100 (0.7) Typ .028 (5.08) .200 Terminal numbers are not on switch. (0.25) Typ .010 (2.6) Dia .102 (10.0) .394 8 C 4 34 56 2 C 1 1 C 2 (1.7) Typ .067 (7.6) .300 (0.5) Typ .020 (2.54) Typ .100 4 C 8 (0.4) .016 (0.7) Typ .028 (5.08) .200 Terminal numbers are not on switch. (2.6) Dia .102 (0.25) Typ .010 2 (10.0) .394 C 1 (0.9) Typ .035 (1.3) Typ .051 1 C 2 (1.7) Typ .067 (10.0) .394 8 C 4 (5.08) .200 (1.1) Typ .043 (2.54) Typ .100 4 C 8 (7.6) .300 (0.4) .016 (0.5) Typ .020 (2.54) Typ .100 (0.7) Typ .028 (5.08) .200 (7.8) .307 Terminal numbers are not on switch. 11-07 8mm Process Sealed SMT DIP Rotaries T YPICAL SWITCH DIMENSIONS Shaft Actuated • Upright with Bracket (0.6) .024 (2.6) Dia .102 (7.92) .312 CD EF0 1 2 Series ND3 (0.25) Typ .010 2 (10.0) .394 C 1 (0.9) Typ .035 (1.3) Typ .051 1 C 2 (1.7) Typ .067 (10.0) .394 8 C 4 (5.08) .200 (1.1) Typ .043 (2.54) Typ .100 4 C 8 (7.6) .300 34 56 (0.3) .012 (8.12) .320 (3.2) .126 (5.6) .220 ND3KC16B Screwdriver Actuated • Right Angle (1.3) .051 (0.7) Typ .028 (3.8) .150 2 8 C4 1 (0.6) .024 (8.02) .316 9 78 (3.8) .150 (8.12) .320 (10.0) .394 ND3FC10H Shaft Actuated • Right Angle (1.3) .051 (0.7) Typ .028 (3.8) .150 2 8 C4 1 (0.6) .024 (8.02) .316 EF0 1 2 BCD (3.8) .150 (8.12) .320 (10.0) .394 ND3KR16H N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 456 789 AB (0.4) .016 (0.5) Typ .020 (2.54) Typ .100 (0.7) Typ .028 (5.08) .200 (7.8) .307 Terminal numbers are not on switch. (2.6) Dia .102 01 (1.0) .039 (4.9) .193 (0.3) .012 (0.635) Typ .025 (0.7) Typ .028 (1.27) Typ .050 1 4 C 8 2 (8.0) .315 (0.7) .028 (1.4) .055 23 (0.5) Typ .020 (1.27) .050 (7.9) .311 (0.4) .016 (0.5) Typ .020 (1.27) Typ .050 (1.3) Typ .051 (1.8) .071 (5.7) .224 Terminal numbers are not on switch. (1.0) .039 (2.6) Dia .102 (4.9) .193 (0.3) .012 (0.635) Typ .025 (0.7) Typ .028 (1.27) Typ .050 1 4 C 8 2 (8.0) .315 (0.7) .028 (1.4) .055 34 56 78 9A (0.5) Typ .020 (1.27) .050 (3.2) .126 (7.9) .311 (0.4) .016 (0.5) Typ .020 (1.27) Typ .050 (1.3) Typ .051 (1.8) .071 (5.7) .224 Terminal numbers are not on switch. 11-07 8mm Process Sealed SMT DIP Rotaries PACKAGING R Tape-Reel Packaging for Upright & Right Angle Switches must be ordered in 500-piece increments when tape-reel packaging is selected. This packaging meets EIA-481-2 Standard for “16mm and 24mm Embossed Carrier Taping of Surface Mount Components for Automatic Handling.” Series ND3 No Code Partitioned Tray for Upright & Right Angle Any Quantity If the ND3 is ordered in less than 500-piece increments, the switches are packaged in a partitioned tray. No code is required. N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 11-07 8mm Process Sealed SMT DIP Rotaries PACKAGING (CONTINUED) For Upright & Upright with Bracket (Codes P & B with F Actuator) Series ND3 Each tape-reel of 550 pockets contains 500 switches Minimum Leader Length: 9.05” (230mm) Minimum Trailer Length: 6.30” (160mm) (1.75) .069 (78.49) Dia 3.090 (2.0) Typ .079 (16.0) Typ .630 (4.0) Typ .157 (10.35) Typ .4075 (1.5) Dia Typ .059 (6.1) .240 (5.5) .217 Overall Dia (330.0) 13.0 (21.0) Dia .827 (2.0) .079 (24.4) .961 Direction of Feed Reel Dimensions Tape Dimensions For Upright & Upright with Bracket (Codes P & B with K Actuator) Each tape-reel of 530 pockets contains 500 switches Minimum Leader Length: 9.05” (230mm) Minimum Trailer Length: 6.30” (160mm) (1.75) .069 (78.49) Dia 3.090 (2.0) Typ .079 (16.0) Typ .630 (4.0) Typ .157 (10.35) Typ .4075 Overall Dia (330.0) 13.0 (21.0) Dia .827 (2.0) .079 (24.4) .961 Direction of Feed Reel Dimensions For Right Angle (Code H with F or K Actuator) Tape Dimensions Each tape-reel of 550 pockets contains 500 switches Minimum Leader Length: 9.05” (230mm) Minimum Trailer Length: 6.30” (160mm) (4.0) Typ .157 (1.75) .069 (78.49) Dia 3.090 (16.0) Typ .630 (2.0) Typ .079 (10.9) Typ .429 (6.3) Typ .248 (13.0) Dia .512 (2.0) Typ .079 Overall Dia (330.0) 13.0 (21.0) Dia .827 (11.5) .453 (24.0) .945 (10.7) .421 (2.0) .079 (24.4) .961 Direction of Feed Reel Dimensions Tape Dimensions 11-07 N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com BC D (13.0) Dia .512 (2.0) Typ .079 (11.5) .453 (24.0) .945 E F 01 2 23 (13.0) Dia .512 (2.0) Typ .079 (11.5) .453 (24.0) .945 78 56 (10.6) .417 9 01 4 (0.5) .020 (1.5) Dia Typ .059 (9.3) .366 (8.6) .339 34 56 (10.6) .417 78 9A (0.5) .020 (1.5) Dia Typ .059 (8.7) .343 (8.1) .319 (0.5) .020