NP0115AG03ND-JB

Subminiature Smooth Actuation Pushbuttons Series NP01 Distinctive Characteristics Soft touch actuation achieved by mechanical silicon rubber structure (patent pending). Distinct, long stroke of 1.5mm (.059”). Entire cap is fully illuminated with single or bicolor LED. Compact design with dimension of 12.5mm (.492”) from PC board to top of cap. Alternating legend options (patent pending) with bicolor LED. Available in both high (2.5N) or standard (1.5N) operating force. Gold plated contacts provide high reliability. Crimped terminals ensure secure PC mounting and prevent dislodging during soldering. Molded-in terminals prevent entry of flux, solvents, and other contaminants. Nonilluminated models available. Actual Size w ww.nkkswitches.com • Toll Free 1.877.2BUYNKK • Tel 480.991.0942 • Fax 480.998.1435 • Email: sales@nkkswitches.com 109 Subminiature Smooth Actuation Pushbuttons Series NP01 General Specifications Electrical Capacity (Resistive Load) Logic Level: 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Stroke: 50 milliohms maximum 500 megohms minimum @ 250V DC 250V AC minimum between contacts for 1 minute minimum 500,000 operations minimum 500,000 operations minimum Standard: 1.5 ±0.5 Newtons High: 2.5N ±0.8 Newtons 1.5mm (.059”) Materials & Finishes Actuator: Case: Base: Movable Contact: Stationary Contacts: Switch Terminals: Silicon rubber Polycarbonate resin Glass fiber reinforced polyamide resin Silver over nickel with gold plating Brass with gold plating Brass with gold plating Environmental Data Operating Temperature Range: Humidity: Vibration: Shock: Illuminated: –25°C through +50°C (–13°F through +122°F) Nonilluminated: –25°C through +70°C (–13°F through +158°F) 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Installation Cap Installation Force: 5.0N maximum downward force on actuator PCB Processing Soldering: Cleaning: Wave Soldering: 270°C maximum @ 6 seconds maximum Manual Soldering: 390°C maximum @ 4 seconds maximum These devices are not process sealed. Hand clean locally using alcohol based solution. Standards & Certifications UL Recognition or CSA Certification: The NP01 Series pushbuttons have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy. w ww.nkkswitches.com • Toll Free 1.877.2BUYNKK • Tel 480.991.0942 • Fax 480.998.1435 • Email: sales@nkkswitches.com 109 Subminiature Smooth Actuation Pushbuttons T YPICAL SWITCH ORDERING EXAMPLE Series NP01 JF PACKAGING No Code Partitioned Tray, Any Quantity (With or without caps installed) Stick-Tube 50 Pieces/Stick (For switch body only; caps packaged separately) N P 01 POLE & CIRCUIT 15 SPST OFF 15 (ON) H G03 L N L Illuminated F CONTACTS & TERMINALS G03 Gold Contacts and PC Terminals, Rated 0.4VA @ 28V AC/DC ILLUMINATION Nonilluminated ( ) = Momentary Normally Open Contacts OPERATING FORCE A H Standard (1.5N) (Black Switch Body) High (2.5N) (Gray Switch Body) LEDS Single or Bicolor LED C D F CF Red Amber Green Bicolor Red/Green CAP TYPES & COLORS Cap Lens/Diffuser Colors JB JC JD JF Clear/White (Combine with any LED) Clear/Red Clear/Amber Clear/Green S Bicolor LED CF Red/Green Cap with A LTERNATING LEGENDS G REEN RED J01 J02 J04 ON START OPEN OFF STOP CLOSE Nonilluminated N No LED A B C H Solid Color Cap Black White Red Gray DESCRIPTION FOR TYPICAL ORDERING EXAMPLE NP0115HG03LF-JF High (2.5N) Operating Force SPST OFF-Momentary ON Circuit Normally Open Contacts Clear Lens with Green Diffuser Green LED Gold Contacts with 0.4VA Rating Straight PC Terminals w ww.nkkswitches.com • Toll Free 1.877.2BUYNKK • Tel 480.991.0942 • Fax 480.998.1435 • Email: sales@nkkswitches.com 109 Subminiature Smooth Actuation Pushbuttons P OLE & CIRCUIT Illuminated Models Plunger Position ( ) = Momentary Normal Pole Model Down Series NP01 Connected Terminals Throw & Switch Schematic Notes: Switch is marked with LC1, 1, L3, L4, L1, L2, 2, LC2. Lamp circuit is isolated and requires an external power source. SP NP0115AG03L NP0115HG03L OFF (ON) Normally Open 1-2 SPST 1 2 (+) (-) Nonilluminated Models Plunger Position ( ) = Momentary Normal Pole Model Down Note: Switch is marked with LC1, 1, L3, L4, L1, L2, 2, LC2. Connected Terminals Throw & Switch Schematic SP NP0115AG03N NP0115HG03N OFF (ON) Normally Open 1-2 SPST 1 2 OPERATING FORCE A Standard Nominal Operating Force 1.5 ±0.5N Switch base is Black H High Nominal Operating Force 2.5 ±0.8N Switch base is Gray CONTACTS, TERMINALS, & RATING G03 Gold Contacts Straight PC Terminals 0.4VA maximum @ 28V AC/DC maximum ILLUMINATION L Illuminated N Nonilluminated w ww.nkkswitches.com • Toll Free 1.877.2BUYNKK • Tel 480.991.0942 • Fax 480.998.1435 • Email: sales@nkkswitches.com 109 Subminiature Smooth Actuation Pushbuttons LED COLORS & SPECIFICATIONS LEDs are an integral part of the switch and not available separately. The electrical specifications shown are determined at a basic temperature of 25°C. If the source voltage exceeds the forward voltage, a ballast resistor is required. Single Color LED R Series NP01 R= Where: R = E= VF = IF = E – VF IF Resistor Value (Ohms) Source Voltage (V) Forward Voltage (V) Forward Current (A) + IF Anode E VF Cathode – Bicolor LED Electrostatic Sensitive Devices Attention C Color IFM VF VRM ∆IF Red 50mA 20mA 2.0V 5V D Amber 50mA 20mA 2.1V 5V F Green 30mA 20mA 3.5V 5V Electrostatic Sensitive Devices Attention CF Color IFM VF VRM ∆IF Red 50mA 20mA 2.0V 5V Green 30mA 20mA 3.5V 5V Forward Peak Current Forward Voltage Reverse Peak Voltage Current Reduction Rate Ambient Temperature Range Forward Peak Current Forward Voltage Reverse Peak Voltage Continuous Forward Current IF Continuous Forward Current IF 0.88mA/°C 0.88mA/°C 0.48mA/°C Current Reduction Rate above 40°C above 40°C above 30°C –25° ~ +50°C Ambient Temperature Range 0.88mA/°C 0.48mA/°C above 40°C above 30°C –25° ~ +50°C The electrical specifications shown are determined at a basic temperature of 25°C. Amber LED LC2 (+) LC1 (+) L4 (-) L3 (-) L2 (-) L1 (-) LC1 (+) L2 (-) L1 (-) LC1 (+) Red or Green LEDs Red/Green Bicolor LED LC2 (+) L4 (-) Green L3 (-) Red L2 (-) Red L1 (-) Green C AP TYPES & COLORS AT3022 12mm Square Cap Material: Polycarbonate Resin (12.0) Sq .472 (10.2) .402 Cap for Single or Bicolor LED JB JC Clear Lens/White Diffuser Clear Lens/Red Diffuser JD JF Clear Lens/Amber Diffuser Clear Lens/Green Diffuser Alternating Legend Cap for Bicolor LED AT3023 12mm Square Cap Material: Polycarbonate Resin (12.0) Sq .472 (10.2) .402 Clear Lens Alternating Legend Filter Standard Alternating Legend Pairs J01 ON Green OFF Red J02 START Green STOP Red J04 OPEN Green CLOSE Red Cap illumination is alternating Green/Red; legend text is black. Contact factory for other Alternating Legends. Legend illustrations are approximate representations of the actual characters on the filters. w ww.nkkswitches.com • Toll Free 1.877.2BUYNKK • Tel 480.991.0942 • Fax 480.998.1435 • Email: sales@nkkswitches.com 109 Subminiature Smooth Actuation Pushbuttons CAP TYPES & COLORS (CONTINUED) Solid Color Cap for Nonilluminated AT3024 12mm Square Cap Material: Polycarbonate Resin (12.0) Sq .472 (10.2) .402 Series NP01 A B Black White C H Red Gray T YPICAL SWITCH DIMENSIONS Illuminated • Straight PC (2.1) .083 L4 L3 1 LC1 (2.0) Typ .079 LC1 1 L3 L4 LC2 2 C L L2 L1 (7.0) .276 (0.3) Typ .012 (3.3) .130 (2.0) Typ .079 L1 L2 2 LC2 (7.0) .276 (1.0) Dia Typ .039 (12.0) Sq .472 (10.2) .402 (12.5) .492 (0.5) Typ .020 NP0115HG03LF-JF PACKAGING No Code Partitioned Tray Any quantity. No code is required. Switches may be packaged with or without caps installed. S Stick-Tube Packaging 50 pieces per stick Switches must be ordered in 50-piece increments when stick-tube packaging is selected. This packaging is for the switch body only. Caps will be packaged separately. (15.3) .602 (11.85) .467 (470.0) 18.504 PRECAUTIONS FOR HANDLING & STORAGE 1. NP01 Pushbuttons are electrostatically sensitive. To prevent damage to LED, devices must be properly isolated from static electricity. 2. Once the cap is installed onto the switch body, it cannot be removed. 3. When assembling cap, align projection on switch body to slot on inside of cap. (Refer to illustration at right.) 4. Legends may be printed on the lens with laser etch, screen print or pad print methods. Epoxy based ink is recommended. 5. Do not use excessive force during installation on PC board or for cap installation. w ww.nkkswitches.com • Toll Free 1.877.2BUYNKK • Tel 480.991.0942 • Fax 480.998.1435 • Email: sales@nkkswitches.com 109 Slot Electrostatic Sensitive Devices Attention Projection