P2021BP/CUL

Electrical Capacity Resistive Load: Motor Load: Lamp Load: Other Ratings Toggle Cap: Lever: Bushing: Frame: Case/Base: Movable Contacts: Stationary Contacts: Terminals: Tactiles Slides Rotaries Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Angle of Throw: Materials & Finishes Environmental Data Operating Temp Range: Humidity: Vibration: Shock: Indicators Touch Tilt Installation Soldering Time & Temp: Cleaning: Standards & Certifications 10A @ 125V AC or 6A @ 250V AC 400W @ 125V AC 2A @ 125V AC for On-Off-On circuit & 3A @ 125V AC for other circuits 10 milliohms maximum 1,000 megohms minimum @ 500V DC 2,000V AC minimum between contacts for 1 minute minimum; 4,000V AC minimum between contacts & case for 1 minute minimum 100,000 operations minimum 25,000 operations minimum 25° Polypropylene Brass with chrome plating Brass with nickel plating Stainless steel Diallyl phthalate resin (UL94V-0) Silver alloy with silver plating Pure silver with silver plating Copper with silver plating –10°C through +85°C (+14°F through +185°F) 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Wave Soldering Recommended (Straight PC): See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section. These devices are not process sealed. Hand clean locally using alcohol based solution. Flammability Standards: UL: UL94V-0 rated case/base File No. E44145 - Recognized only when ordered with marking on switch. Add “/U” or “/CUL” to end of part number to order UL recognized switch. All models recognized at 10A @ 125V AC & 6A @ 250V AC. CSA: File No. 023535_0_000 - Certified only when ordered with marking on switch. Add “/C” to end of part number to order CSA certified switch. All models certified at 10A @ 125V AC & 6A @ 250V AC. VDE: License No. 119174 All models approved at 10A @ 125V AC & 6A @ 250V AC. Marking on switch is standard. All models meet EN 61058-1 standard. Supplement Accessories Internationally Approved Toggles General Specifications Programmable Illuminated PB A Keylocks Pushbuttons Rockers Toggles Series P A96 www.nkkswitches.com A Rockers Distinctive Characteristics Toggles Series P Internationally Approved Toggles Pushbuttons Meets EN 61058-1 standard. Programmable Illuminated PB High torque bushing construction prevents rotation or separation from frame during installation. Stainless steel frame resists corrosion and increases environmental safety. Case/base of heat resistant resin meets UL94V-0 flammability standard. Keylocks Contacts of special silver alloy resist arcing and guarantee stable electrical contact and long life. Slides Rotaries High insulating barriers increase isolation of circuits in double pole devices and provide added protection to contact points. Tactiles Prominent external insulating barriers increase insulation resistance and dielectric strength. Actual Size Supplement Accessories Indicators Touch Clinching of the frame to the case well above the base and terminals provides 4,000V dielectric strength. Tilt Epoxy sealed terminals prevent entry of flux, solvents, and other contaminants. www.nkkswitches.com A97 TYPICAL SWITCH ORDERING EXAMPLE P20 Pushbuttons 22 Poles & Circuits B Toggles & Bushings 11 SPST ON NONE OFF 12 SPDT ON NONE ON 13 SPDT ON OFF ON 21 DPST ON NONE OFF 22 DPDT ON NONE ON 23 DPDT ON OFF ON Keylocks Programmable Illuminated PB Internationally Approved Toggles A Rockers Toggles Series P No Code Terminals .512” (13.0mm) White Cap with 6mm Bushing E .450” (11.4mm) Flatted with 6mm Bushing B .689” (17.5mm) Large Bat with 12mm Bushing D .748” (19.0mm) White Capped Column with 12mm Bushing No Code Solder Lug P Straight PC Z .187” (4.75mm) Quick Connect DESCRIPTION FOR TYPICAL ORDERING EXAMPLE P2022B Rotaries IMPORTANT: VDE is marked on all models. Switches are supplied without UL, cULus & CSA marking unless specified. UL, cULus & CSA recognized only when ordered with marking on the switch. Specific models, ratings, & ordering instructions are noted on the General Specifications page. .689” (17.5mm) Large Bat with 12mm Bushing Slides DPDT ON-NONE-ON Circuit Tactiles Solder Lug Terminals POLES & CIRCUITS Tilt Toggle Position Down Model SP P2011 Up Keyway Down Center Throw & Schematics Up Note: Terminal numbers are on the switch. Keyway Supplement Accessories Indicators Touch Pole Center Connected Terminals ON NONE OFF 1-1b OPEN OPEN 1 (COM) SPST 1b 1 (COM) SP P2012 P2013 ON ON NONE OFF ON ON 1-1b OPEN 1-1a SPDT DP P2021 ON NONE OFF 1-1b 2-2b OPEN OPEN DPST DP P2022 P2023 ON ON NONE OFF ON ON 1-1b 2-2b OPEN 1-1a 2-2a DPDT A98 1a 1 (COM) 2 1b 1 1a www.nkkswitches.com 1b 2b (COM) 1b 2a 2 2b (13.0) .512 (19.0) .748 (17.5) .689 (11.4) .450 Panel Cutouts Panel Thickness with Keyway .134” (3.4mm) maximum Panel Thickness with Locking Ring .102” (2.6mm) maximum (5.6) .220 (6.35) Dia .250 (0.6) .024 (12.5) Dia .492 Panel Thickness with Keyway .256” (6.5mm) maximum (6.5) .256 (6.35) Dia .250 (2.2) Dia .087 Pushbuttons (2.54) .100 25° (4.4) Dia .173 Panel Thickness with Locking Ring .217” (5.5mm) maximum (11.5) .453 (1.5) .060 (12.5) Dia .492 (9.0) .354 (3.0) Dia .118 Standard Hardware For 6mm Bushing: 1 Locking Ring AT507M, 1 Internal Tooth Lockwasher AT509, 2 Hex Nuts AT513M For 12mm Bushing: 1 Hex Face Nut AT503M, 1 Locking Ring AT506M, 1 Internal Tooth Lockwasher AT508, 1 Hex Mounting Nut AT527M Optional Splashproof Boot Assemblies (for code B): AT401 & AT4181 boots plus hex nut & o-ring; see Accessories & Hardware section. TERMINALS Epoxy Seal P Straight PC (4.8) .189 (2.6) .102 SPST 1 (1.17) .046 Thk = (1.0) .039 2b 1b (7.62) Typ .300 SPDT (1.8) Dia Typ .071 (7.62) Typ .300 1 DPST (7.62) Typ .300 1 DPDT (1.8) Dia Typ .071 (10.16) .400 (1.8) Dia Typ .071 (4.75) .187 Thk = (0.8) .031 1b 2 1a (9.0) .354 (6.35) .250 (1.3) Dia .051 1b (7.6) .299 .187” (4.75mm) Quick Connect Z (2.0) (4.5) .079 .177 (1.25) .049 Thk = (1.0) .039 Solder Lug Rotaries Epoxy Seal 2b 1b 2 1 2a (7.62) Typ .300 1a (10.16) .400 (1.8) Dia Typ .071 Tactiles No Code TYPICAL SWITCH DIMENSIONS P2011, P2012, P2013 Keyway M6 P0.75 (1.25) x (2.0) Typ .049 x .079 6mm Bushing (1.0) Typ .039 Tilt 1b (0.8) .031 (7.62) .300 (13.0) .512 (5.0) .197 (22.0) .866 Touch (0.9) .035 (8.0) .315 1a (0.5) .020 (2.6) .102 P2021B, P2022B, P2023B Keyway (1.25) x (2.0) Typ .049 x .079 M12 P1 12mm Bushing (1.0) Typ .039 2b (0.8) .031 (7.62) .300 25° (6.0) Dia .236 (20.0) .787 P2012 P2011 models do not have terminal 1a. (17.5) .689 (12.0) .472 (21.1) .831 (5.0) .197 1b 2 1 2a (0.5) .020 (20.5) .807 1a (10.16) .400 (2.6) Typ .102 P2021 models do not have terminals 1a & 2a. www.nkkswitches.com Accessories (4.2) Dia .165 (20.5) .807 1 Supplement 25° (11.0) .433 Programmable Illuminated PB (4.2) Dia .165 25° (6.0) Dia .236 (5.08) .200 25° .748” (19.0mm) White Capped Column with 12mm Bushing D Keylocks 25° .689” (17.5mm) Large Bat with 12mm Bushing B Slides .450” (11.4mm) Flatted with 6mm Bushing E Indicators .512” (13.0mm) White Cap with 6mm Bushing No Code Rockers A TOGGLES & BUSHINGS Toggles Series P Internationally Approved Toggles P2022B A99