SK14EG30

Toggles Series SK Rockers General Specifications Electrical Capacity (Resistive Load) Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Torque: Contact Timing: Angle of Throw: Pushbuttons 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) See Supplement section to find explanation of operating range Programmable Illuminated PB Logic Level: 80 milliohms maximum 100 megohms minimum @ 500V DC 500V AC minimum for 1 minute minimum 30,000 cycles minimum 10,000 cycles minimum .026Nm (.234 lb•in) for momentary action models .020Nm (.182 lb•in) for maintained action models Break-before-make 90° for 2-position & 45° for 3-position F Keylocks Process Sealed Keylocks Materials & Finishes Tactiles Slides Rotaries Boot: Polyvinyl chloride Key: Brass alloy with bright nickel plating; brass alloy with bright nickel plating & ABS resin handle Tumbler Barrel: Polyacetal Bushing: Zinc alloy with nickel plating Bracket: Steel with tin plating Base: Glass fiber reinforced polyamide Movable Contactor: Beryllium copper with gold plating Stationary Contacts: Copper with gold plating Terminals: Brass with tin plating Standards & Certifications Indicators Wave Soldering recommended: See Profile B in Supplement section. Manual Soldering: See Profile B in Supplement section. Automated cleaning. Boot must be on switch during processing. See Cleaning specifications in Supplement section. Accessories Soldering: Cleaning: These SK Series devices have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy. www.nkkswitches.com Supplement PCB Processing Touch Operating Temperature Range: –25°C through +70°C (–13°F through +158°F) Humidity: 90 ~ 95% humidity for 240 hours @ 40°C (104°F) Vibration: 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours Shock: 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Tilt Environmental Data F19 Toggles Series SK Rockers Distinctive Characteristics Pushbuttons Sealed body construction plus disposable boot protect contacts and allow automated processing. Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Molded-in terminals seal out flux, solvents, and other contaminants. Short body size for space-saving, behind panel dimensions. F Detent mechanism, with its spring-operated steel ball, gives crisp, positive action for accurate switch setting. Bifurcated, self-wiping contact mechanism provides unequalled logic-level reliability and smoother, positive detent actuation. Crimped bracket legs ensure secure PCB mounting and prevent dislodging during automated wave soldering. .100” x .100” (2.54mm x 2.54mm) terminal spacing conforms to standard PC board grid spacing. Touch Tilt Process Sealed Keylocks Supplement Accessories Indicators Actual Size F20 www.nkkswitches.com Toggles Series SK 4E G Poles 1 SPDT SP3T 2 DPDT DP3T 30 Pushbuttons 2 Programmable Illuminated PB SK Rockers TYPICAL SWITCH ORDERING EXAMPLE Contact Material G Gold Rated 0.4VA @ 28V AC/DC Circuits & Key-Removable Positions PC Terminals Pos. 1 Pos. 2 Pos. 3 Key Removes 13 Straight with Bracket 2A ON NONE ON Positions 1 and 3 30 Right Angle 2B ON NONE ON Position 1 5B ON NONE (ON) Position 1 *4D ON ON ON Positions 1, 2, 3 *4E ON ON ON Position 2 F Rotaries Code Keylocks Process Sealed Keylocks Tactiles Slides ( ) = Momentary *Can be used as ON-OFF-ON circuit Tilt DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Touch SK24EG30 Gold Contacts Rated 0.4VA DP3T ON-ON-ON Circuit Key Removable in Position 2 Indicators Right Angle PC Terminals Supplement Accessories 2 Keys Supplied with each Switch www.nkkswitches.com F21 Series SK Toggles Process Sealed Keylocks Model Pos 1 Pos 2 Pos 3 Pos 1 SPDT SK12A ON NONE ON C1-1 Pos 2 ON ON NONE NONE ON (ON) C1-1 DPDT SK22A ON NONE ON C1-1 C2-4 ____ DPDT DPDT SK22B SK25B ON ON NONE NONE ON (ON) C1-1 C2-4 ____ ON ON ON C1 C1-2 3 POS 1 ____ C1-1 Schematic Pos 3 = Key Removable = Not Removable = Maximum Arc POS 1 ____ SK12B SK15B SK14D • (Terminal numbers are not on switch) SPDT SPDT C1-2 1 3 POS 1 C1-2 C2-5 C1 C2 3 POS 1 C1-2 C2-5 C1-2 2 1 2 4 5 3 POS 1 C1 C1-3 2 3 2 F SP3T SK14E ON ON ON C1-1 C1-2 C1-3 DP3T SK24D ON ON ON C1-1 C2-4 C1-2 C2-5 C1-3 C2-6 DP3T SK24E ON ON ON C1-1 C2-4 C1-2 C2-5 C1-3 C2-6 1 2 3 C1 3 POS 1 POS 1 C2 2 3 2 1 2 3 POS 1 4 5 6 3 Slides KEY REMOVABLE Positions 1 & 3 90° Angular Throw B Position 1 90° Angular Throw Tactiles A D Positions 1, 2 & 3 45° Angular Throw E Position 2 45° Angular Throw CONTACT MATERIAL & RATING Tilt G Gold over Copper Logic Level 0.4VA maximum @ 28V AC/DC maximum Touch TERMINALS 13 Straight PC Terminals with Bracket Double Throw Model 30 Three Throw Model Supplement Accessories Indicators Connected Terminals Key Positions Pole & Throw SP3T Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers POLES, CIRCUITS & KEY-REMOVABLE POSITIONS F22 www.nkkswitches.com Right Angle PC Terminals Double Throw Model Three Throw Model Series SK Toggles Process Sealed Keylocks KEYS Brass Alloy with Bright Nickel Plating & ABS Resin Handle PCB (10.1) .398 Suitable for all Straight PCB mount and for Right Angle PCB mount where clearance for key is obtainable. Programmable Illuminated PB AT4079 for Right Angle Mid-board Mounting (Optional) All Metal Pushbuttons (14.5) .571 (1.5) .059 2 keys supplied with each switch Rockers (20.0) .787 (5.0) .197 (16.0) .630 Brass Alloy with Bright Nickel Plating (14.0) .551 Contact factory if metal keys needed (1.5) .059 (2.0) .079 (8.8) .346 PCB Disposable Boot Each switch is supplied with a boot that provides protection from automated soldering and the cleaning process. Attach the boot without the key installed in the switch. F Keylocks AT4080 Standard Antistatic Plastic Handle Polyvinyl Chloride TYPICAL SWITCH DIMENSIONS Straight PC with Bracket • Double Throw (20.0) .787 (5.08) Typ .200 (3.0) .118 (14.5) .571 (14.8) .583 (0.3) .012 (10.5) .413 (10.5) .413 (1.0) .039 (5.08) Typ .200 (3.0) .118 (14.8) .583 (0.3) .012 (10.5) .413 Straight PC with Bracket • Three Throw (0.7) Dia Typ .028 4 2 5 3 6 C1 C2 (2.54) Typ .100 (10.5) .413 (3.5) .138 Single Pole models have only terminals 1, 2, 3 & C1 www.nkkswitches.com Tactiles SK12AG13 1 (20.0) .787 (10.16) .400 (0.5) Typ .020 (2.54) .100 POS 3 (14.5) .571 (0.7) Typ .028 (3.5) .138 Single & Double Pole 45° (12.0) Dia .472 C2 (2.54) Typ .100 POS 2 POS 1 C1 (15.74) .620 Single Pole models have only terminals 1, 2 & C1 45° 5 Tilt POS 3 4 1 2 Touch (1.0) .039 Indicators 90° (12.0) Dia .472 (0.7) Dia Typ .028 (0.5) Typ .020 (2.54) .100 POS 1 (15.74) .620 Accessories Single & Double Pole (0.7) Typ .028 (10.16) .400 Supplement Slides Rotaries The boot is not reusable; discard after the washing procedure. SK24DG13 F23 Series SK Toggles Process Sealed Keylocks TYPICAL SWITCH DIMENSIONS Rockers Right Angle Key in Position 1 Single Pole PC Terminals Double Throw (5.0) Pushbuttons .197 Programmable Illuminated PB (10.5) .413 (0.7) Typ .028 POS 1 (12.0) Dia .472 (14.8) .583 (7.62) .300 (2.54) .100 C1 (2.54) Typ .100 (2.54) .100 (5.08) .200 5 4 (3.5) .138 C2 (1.0) .039 POS 3 (15.24) .600 (20.0) .787 (9.0) .354 2 1 Key in Position 3 (3.5) (0.7) Dia Typ .138 .028 (5.08) .200 Double Pole Right Angle Key in Position 2 Single Pole PC Terminals Three Throw (16.3) .642 (5.0) .197 Rotaries (16.3) .642 C1 (2.54) Typ .100 (2.54) .100 SK15BG30 Keylocks (12.4) .488 (3.0) .118 F 2 1 (0.7) Dia .028 90° (0.5) Typ .020 (16.3) .642 (9.0) .354 (9.0) .354 POS 1 45° Slides (12.0) Dia .472 POS 2 (14.8) .583 45° (10.5) .413 (0.7) Typ .028 (12.4) .488 1 (0.7) Dia .028 (2.54) .100 (7.62) .300 2 3 C1 (2.54) Typ .100 (2.54) .100 (5.08) .200 6 5 4 (3.5) .138 C2 POS 3 Tactiles (0.5) Typ .020 (9.0) .354 (15.24) .600 Tilt (3.0) .118 SK24EG30 1 Key in Position 1 Touch 2 (15.24) .600 (5.08) .200 4 1 5 2 (15.24) .600 C1 C2 (0.8) Dia Typ .031 (10.16) .400 (5.08) .200 SPDT (5.08) .200 (2.54) .100 2 C1 1 (2.54) Typ .100 (2.54) .100 (5.08) .200 DPDT C2 5 4 C1 2 1 (7.62) .300 CL F24 (0.8) Dia Typ .031 (2.54) .100 C1 (5.08) .200 5 2 6 3 C2 C1 (5.08) .200 (0.8) Dia Typ .031 (10.16) .400 (0.8) Dia Typ .031 (10.16) .400 Right Angle PC Footprints SP3T (5.08) .200 (2.54) .100 3 C1 (7.62) .300 CL 1 4 DP3T 3 (2.54) Typ .100 (2.54) .100 (2.54) Typ .100 1 2 SP3T (0.8) Dia Typ .031 (10.16) .400 (3.5) (0.7) Dia Typ .138 .028 (5.08) .200 (2.54) Typ .100 Supplement Accessories Indicators C1 DPDT C1 Straight PC Footprints (2.54) Typ .100 1 SPDT 3 Double Pole (2.54) Typ .100 2 (2.54) Typ .100 (2.54) .100 (16.3) .642 (0.8) Dia Typ .031 www.nkkswitches.com 2 1 (2.54) Typ .100 (2.54) .100 (5.08) .200 DP3T (2.54) Typ .100 (2.54) .100 C2 6 5 4 C1 3 2 1 (7.62) .300 (7.62) .300 CL (0.8) Dia Typ .031 (2.54) .100 CL (0.8) Dia Typ .031