TL22SFAG016G

Series TL Toggles Fully Illuminated Toggles A Rockers General Specifications Electrical Capacity (Resistive Load) Power Level (silver): Logic Level (gold): 6A @ 125V AC or 3A @ 250V AC or 6A @ 12V DC for silver 0.4VA maximum @ 28V AC/DC maximum for gold (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Note: See Supplement Index for explanation of operating range. Programmable Illuminated PB Pushbuttons Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Keylocks Mechanical Life: Electrical Life: Static Capability: Nominal Operating Force: Angle of Throw: 10 milliohms maximum for silver; 20 milliohms maximum for gold 1,000 megohms minimum @ 500V DC 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts & case for 1 minute minimum 50,000 operations minimum 25,000 operations minimum for silver; 50,000 operations minimum for gold Withstands 20 kilovolts ESD minimum 1.9N for .689” (17.5mm) toggle; 2.5N for .433” (11.0mm) toggle 25° Rotaries Materials & Finishes Tactiles Toggle: Housing: Sealing Ring: Base: Movable Contactor: Movable Contacts: Stationary Contact: Lamp Contacts: Power Terminals: Lamp Terminals: Polycarbonate Glass fiber reinforced polyamide Nitrile butadiene rubber Diallyl phthalate (UL94V-0) Phosphor bronze with silver or gold plating Silver alloy or copper with gold plating Silver plus copper with silver plating or copper with gold plating Beryllium copper with silver plating Copper with silver or gold plating Brass with silver plating Slides Tilt Environmental Data Operating Temperature Range: Humidity: Vibration: Shock: Touch –10°C through +55°C (+14°F through +131°F) 90 ~ 95% humidity for 240 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 1.75 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Indicators Installation Mounting Torque: Soldering Time & Temperature: .98Nm (8.67 lb • in) maximum Manual Soldering: See Profile B in Supplement section. Accessories Standards & Certifications Flammability Standards: UL94V-0 base Supplement A118 www.nkk.com Fully Illuminated Toggles Series TL A Toggles Supplement Accessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers Distinctive Characteristics Choice of long or short toggles in translucent colors combine with bright LEDs available in red, amber, and green, plus super bright LEDs available in white, green, and blue. Black face nut enhances front panel appearance. Antistatic material used for toggle withstands 20 kilovolts electrostatic discharge. Panel seal, achieved with use of optional exterior o-ring, conforms to IP65 of IEC60529 Standards. Interior o-ring protects contacts from oil, dust, water, and other contaminants. UL94V-0 flammability rated for base. High insulating barriers protect against crossover. Terminals are molded in and epoxy sealed to lock out flux, dust, and other contaminants. Actual Size www.nkk.com A119 Series TL Toggles Fully Illuminated Toggles TYPICAL SWITCH ORDERING EXAMPLE A Pushbuttons Rockers TL Pole 2 DPDT 2 2 D N Toggle Colors For Bright A W01 Housing 6G LED Colors Bright 5C 5D 5F 6B 6F 6G Red Amber Green White Green Blue Programmable Illuminated PB A Black C D F ON N Red Amber Green Circuit 2 ON NONE For Super Bright No Color Super Bright Keylocks Toggle Lengths D .689” (17.5mm) (combines with silver contacts only) .433” (11.0mm) (combines with gold contacts only) W01 Terminals, Contacts & Ratings Solder Lug Terminals * Silver 6A @ 125V AC for .689” (17.5mm) Toggle only Solder Lug Terminals * Gold 0.4VA @ 28V AC/DC for .433” (11.0mm) Toggle only Rotaries S Tactiles Slides G01 * Wire harness & cable assemblies offered only in Americas Tilt DESCRIPTION FOR TYPICAL ORDERING EXAMPLE TL22DNAW016G Touch Indicators .689” (17.5mm) Toggle Length; No Color (matte finish of clear material) Blue, Super Bright LED DPDT ON-NONE-ON Circuit Solder Lug Terminals Black Housing Silver Contacts with 6-amp Rating Supplement Accessories A120 www.nkk.com Fully Illuminated Toggles POLE & CIRCUIT Toggle Position Down Pole Model Keyway Series TL A Throw & Power/Lamp Schematics Notes: Terminal numbers are not actually on switch. Lamp circuit is isolated and requires an external power source. DPDT 1a 1 (COM) 1b 2a 2 2b (+) (-) Connected Terminals Up Down Keyway DP TL22 ON NONE ON 1-1b 2-2b OPEN 1-1a 2-2a D .689” (17.5mm) (17.5) .689 S .433” (11.0mm) (11.0) .433 Colors Available for Bright LED Combines with Silver Contacts only Material: Polycarbonate Combines with Gold Contacts only Material: Polycarbonate C Red D Amber F Green Color Available for Super Bright LED N No Color (Appearance is matte finish of clear material) HOUSING A Black The housing consists of the one-piece bushing/case of glass fiber reinforced polyamide in black color only. The diallyl phthalate material used for the base is UL flammability rated 94V-0; housing material is not. CONTACT MATERIALS, RATINGS, & TERMINALS W G Silver Contacts Power Level 6A @ 125V AC & 3A @ 250V AC & 6A @ 12V DC Gold Contacts Logic Level 0.4VA maximum @ 28V AC/DC See Supplement Index for complete explanation of operating range. (5.4) .213 Exopy Seal (1.17) .046 (5.0) .197 Turret LED Thk = (0.6) .024 Solder Lug Thk = (0.8) Typ .031 LED CODES & SPECIFICATIONS Electrical specifications are determined at a basic temperature of 25°C. Lamp circuit is independent of switch operation. If the source voltage is greater than rated voltage, a ballast resistor is required. The ballast resistor calculation and more lamp detail are shown in Supplement section. ATTENTION Colored Toggles Clear Toggles ELECTROSTATIC SENSITIVE DEVICES LED Factory Assembled Not Available Separately Forward Peak Current Continuous Forward Current Forward Voltage Reverse Peak Voltage Current Reduction Rate Above 25°C Ambient Temperature Range Color I FM IF VF VRM ∆I F C Red D Amber F Green B White F Green G Blue 20mA 2.0V 4V 20mA 2.1V 4V –10°C ~ +55°C www.nkk.com 20mA 2.27V 4V 20mA 3.6V 5V 20mA 3.5V 5V –10°C ~ +55°C 20mA 3.6V 5V 0.32mA/°C 0.32mA/°C 0.50mA/°C 0.50mA/°C 0.50mA/°C 0.50mA/°C A121 Supplement Accessories 30mA 30mA 50mA 30mA 30mA 30mA Indicators 5 Bright 6 Super Bright Touch Tilt Tactiles (2.0) .079 (3.0) (3.5) .118 .138 (2.0) Typ .079 (1.1) Typ .043 Slides 01 Terminals Solder Lug Rotaries Keylocks Programmable Illuminated PB TOGGLE LENGTHS & COLORS Pushbuttons Rockers Center Center Up Toggles Series TL Toggles Fully Illuminated Toggles TYPICAL SWITCH DIMENSIONS A 17.5mm Toggle Rockers Keyway M12 P1 (3.5) .138 (1.1) x (2.0) Typ .043 x .079 (0.6) Typ .024 (4.7) Typ (13.5) .185 .531 (0.8) Typ .031 (1.17) Typ .046 2b L( )I I v 1a 1b Pushbuttons 25° I L( )v 2a Programmable Illuminated PB (4.5) .177 (18.0) Sq .709 (2.5) .098 (6.0) Dia .236 (17.5) .689 (10.0) .394 (21.0) .827 (5.4) .213 (0.5) Typ .020 (2.0) Typ .079 (5.0) Typ .197 TL22DNAW016G 11.0mm Toggle Keyway M12 P1 (3.5) .138 (1.1) x (2.0) Typ .043 x .079 (0.6) Typ .024 (4.7) Typ (13.5) .185 .531 (0.8) Typ .031 2a Keylocks (1.17) Typ .046 2b L( )I I v 1a 1b 25° Rotaries I L( )v (2.5) .098 (6.0) .236 (18.0) Sq .709 (21.0) .827 (5.4) .213 (0.5) Typ .020 (11.0) .433 (10.0) .394 Slides (2.0) Typ .079 (5.0) Typ .197 TL22SCAG015C STANDARD HARDWARE Tactiles OPTIONAL HARDWARE AT508 Lockwasher Not to use with Panel Seal Steel with Chromate/Zinc (12.1) .476 (12.1) Dia .476 (17.5) Dia .689 AT527MA Black Hex Nut Use as Face Nut Chrome/Steel M12 P1 AT527M Hex Nut Use as Backup Nut Nickel/Steel M12 P1 AT401P O-ring Use for Panel Seal Natural Rubber Tilt (14.0) .551 (14.0) .551 (15.8) Dia .622 Touch (13.8) Dia .543 (16.0) .630 (2.0) .079 (16.0) .630 (2.0) .079 (1.0) .039 (0.5) .020 (1.5) .059 Indicators Hardware details in Accessories & Hardware section. Accessories Panel Cutouts (12.5) Dia .492 Supplement Maximum Panel Thickness with Standard Hardware .157” (4.0mm) (11.5) .453 (12.5) Dia .492 (1.5) .060 Maximum Panel Thickness with Standard Hardware & AT401P O-ring .236” (6.0mm) A122 www.nkk.com