Series TL
Toggles
Fully Illuminated Toggles
A
Rockers
General Specifications
Electrical Capacity (Resistive Load)
Power Level (silver): Logic Level (gold): 6A @ 125V AC or 3A @ 250V AC or 6A @ 12V DC for silver 0.4VA maximum @ 28V AC/DC maximum for gold (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Note: See Supplement Index for explanation of operating range.
Programmable Illuminated PB
Pushbuttons
Other Ratings
Contact Resistance: Insulation Resistance: Dielectric Strength:
Keylocks
Mechanical Life: Electrical Life: Static Capability: Nominal Operating Force: Angle of Throw:
10 milliohms maximum for silver; 20 milliohms maximum for gold 1,000 megohms minimum @ 500V DC 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts & case for 1 minute minimum 50,000 operations minimum 25,000 operations minimum for silver; 50,000 operations minimum for gold Withstands 20 kilovolts ESD minimum 1.9N for .689” (17.5mm) toggle; 2.5N for .433” (11.0mm) toggle 25°
Rotaries
Materials & Finishes
Tactiles
Toggle: Housing: Sealing Ring: Base: Movable Contactor: Movable Contacts: Stationary Contact: Lamp Contacts: Power Terminals: Lamp Terminals:
Polycarbonate Glass fiber reinforced polyamide Nitrile butadiene rubber Diallyl phthalate (UL94V-0) Phosphor bronze with silver or gold plating Silver alloy or copper with gold plating Silver plus copper with silver plating or copper with gold plating Beryllium copper with silver plating Copper with silver or gold plating Brass with silver plating
Slides
Tilt
Environmental Data
Operating Temperature Range: Humidity: Vibration: Shock:
Touch
–10°C through +55°C (+14°F through +131°F) 90 ~ 95% humidity for 240 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 1.75 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Indicators
Installation
Mounting Torque: Soldering Time & Temperature:
.98Nm (8.67 lb • in) maximum Manual Soldering: See Profile B in Supplement section.
Accessories
Standards & Certifications
Flammability Standards:
UL94V-0 base
Supplement
A118
www.nkk.com
Fully Illuminated Toggles
Series TL
A
Toggles Supplement Accessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers
Distinctive Characteristics
Choice of long or short toggles in translucent colors combine with bright LEDs available in red, amber, and green, plus super bright LEDs available in white, green, and blue.
Black face nut enhances front panel appearance.
Antistatic material used for toggle withstands 20 kilovolts electrostatic discharge.
Panel seal, achieved with use of optional exterior o-ring, conforms to IP65 of IEC60529 Standards.
Interior o-ring protects contacts from oil, dust, water, and other contaminants.
UL94V-0 flammability rated for base.
High insulating barriers protect against crossover.
Terminals are molded in and epoxy sealed to lock out flux, dust, and other contaminants.
Actual Size
www.nkk.com
A119
Series TL
Toggles
Fully Illuminated Toggles
TYPICAL SWITCH ORDERING EXAMPLE
A
Pushbuttons
Rockers
TL
Pole
2 DPDT
2
2
D
N
Toggle Colors
For Bright
A
W01
Housing
6G
LED Colors
Bright 5C 5D 5F 6B 6F 6G Red Amber Green White Green Blue
Programmable Illuminated PB
A
Black
C D F ON N
Red Amber Green
Circuit
2 ON NONE
For Super Bright No Color
Super Bright
Keylocks
Toggle Lengths
D .689” (17.5mm) (combines with silver contacts only) .433” (11.0mm) (combines with gold contacts only) W01
Terminals, Contacts & Ratings
Solder Lug Terminals * Silver 6A @ 125V AC for .689” (17.5mm) Toggle only Solder Lug Terminals * Gold 0.4VA @ 28V AC/DC for .433” (11.0mm) Toggle only
Rotaries
S
Tactiles
Slides
G01
* Wire harness & cable assemblies offered only in Americas
Tilt
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
TL22DNAW016G
Touch
Indicators
.689” (17.5mm) Toggle Length; No Color (matte finish of clear material) Blue, Super Bright LED DPDT ON-NONE-ON Circuit Solder Lug Terminals Black Housing Silver Contacts with 6-amp Rating
Supplement
Accessories
A120
www.nkk.com
Fully Illuminated Toggles
POLE & CIRCUIT
Toggle Position
Down Pole Model
Keyway
Series TL
A
Throw & Power/Lamp Schematics
Notes: Terminal numbers are not actually on switch. Lamp circuit is isolated and requires an external power source. DPDT
1a 1 (COM) 1b 2a 2 2b
(+) (-)
Connected Terminals
Up Down
Keyway
DP
TL22
ON
NONE
ON
1-1b 2-2b
OPEN
1-1a 2-2a
D
.689” (17.5mm)
(17.5) .689
S
.433” (11.0mm)
(11.0) .433
Colors Available for Bright LED
Combines with Silver Contacts only Material: Polycarbonate
Combines with Gold Contacts only Material: Polycarbonate
C
Red
D
Amber
F
Green
Color Available for Super Bright LED
N
No Color (Appearance is matte finish of clear material)
HOUSING A
Black
The housing consists of the one-piece bushing/case of glass fiber reinforced polyamide in black color only. The diallyl phthalate material used for the base is UL flammability rated 94V-0; housing material is not.
CONTACT MATERIALS, RATINGS, & TERMINALS W G
Silver Contacts Power Level 6A @ 125V AC & 3A @ 250V AC & 6A @ 12V DC Gold Contacts Logic Level 0.4VA maximum @ 28V AC/DC
See Supplement Index for complete explanation of operating range.
(5.4) .213 Exopy Seal (1.17) .046 (5.0) .197
Turret LED Thk = (0.6) .024
Solder Lug Thk = (0.8) Typ .031
LED CODES & SPECIFICATIONS
Electrical specifications are determined at a basic temperature of 25°C. Lamp circuit is independent of switch operation. If the source voltage is greater than rated voltage, a ballast resistor is required. The ballast resistor calculation and more lamp detail are shown in Supplement section.
ATTENTION
Colored Toggles
Clear Toggles
ELECTROSTATIC SENSITIVE DEVICES
LED Factory Assembled Not Available Separately Forward Peak Current Continuous Forward Current Forward Voltage Reverse Peak Voltage Current Reduction Rate Above 25°C Ambient Temperature Range
Color I FM IF VF VRM ∆I F
C
Red
D
Amber
F
Green
B
White
F
Green
G
Blue
20mA 2.0V 4V
20mA 2.1V 4V –10°C ~ +55°C
www.nkk.com
20mA 2.27V 4V
20mA 3.6V 5V
20mA 3.5V 5V –10°C ~ +55°C
20mA 3.6V 5V
0.32mA/°C 0.32mA/°C 0.50mA/°C 0.50mA/°C 0.50mA/°C 0.50mA/°C
A121
Supplement
Accessories
30mA
30mA
50mA
30mA
30mA
30mA
Indicators
5 Bright
6 Super Bright
Touch
Tilt
Tactiles
(2.0) .079 (3.0) (3.5) .118 .138 (2.0) Typ .079 (1.1) Typ .043
Slides
01 Terminals
Solder Lug
Rotaries
Keylocks
Programmable Illuminated PB
TOGGLE LENGTHS & COLORS
Pushbuttons
Rockers
Center
Center
Up
Toggles
Series TL
Toggles
Fully Illuminated Toggles
TYPICAL SWITCH DIMENSIONS
A
17.5mm Toggle
Rockers
Keyway
M12 P1
(3.5) .138
(1.1) x (2.0) Typ .043 x .079 (0.6) Typ .024 (4.7) Typ (13.5) .185 .531 (0.8) Typ .031
(1.17) Typ .046
2b L( )I I v 1a 1b
Pushbuttons
25°
I L( )v 2a
Programmable Illuminated PB
(4.5) .177 (18.0) Sq .709
(2.5) .098
(6.0) Dia .236 (17.5) .689 (10.0) .394 (21.0) .827
(5.4) .213
(0.5) Typ .020
(2.0) Typ .079 (5.0) Typ .197
TL22DNAW016G
11.0mm Toggle
Keyway M12 P1 (3.5) .138 (1.1) x (2.0) Typ .043 x .079 (0.6) Typ .024 (4.7) Typ (13.5) .185 .531 (0.8) Typ .031
2a
Keylocks
(1.17) Typ .046
2b L( )I I v 1a 1b
25°
Rotaries
I L( )v
(2.5) .098 (6.0) .236 (18.0) Sq .709 (21.0) .827 (5.4) .213
(0.5) Typ .020
(11.0) .433
(10.0) .394
Slides
(2.0) Typ .079 (5.0) Typ .197
TL22SCAG015C
STANDARD HARDWARE
Tactiles
OPTIONAL HARDWARE
AT508 Lockwasher Not to use with Panel Seal Steel with Chromate/Zinc
(12.1) .476 (12.1) Dia .476 (17.5) Dia .689
AT527MA Black Hex Nut Use as Face Nut Chrome/Steel
M12 P1
AT527M Hex Nut Use as Backup Nut Nickel/Steel
M12 P1
AT401P O-ring Use for Panel Seal Natural Rubber
Tilt
(14.0) .551
(14.0) .551
(15.8) Dia .622
Touch
(13.8) Dia .543 (16.0) .630 (2.0) .079 (16.0) .630 (2.0) .079 (1.0) .039 (0.5) .020 (1.5) .059
Indicators
Hardware details in Accessories & Hardware section.
Accessories
Panel Cutouts
(12.5) Dia .492
Supplement
Maximum Panel Thickness with Standard Hardware .157” (4.0mm)
(11.5) .453 (12.5) Dia .492 (1.5) .060
Maximum Panel Thickness with Standard Hardware & AT401P O-ring .236” (6.0mm)
A122
www.nkk.com
很抱歉,暂时无法提供与“TL22SNAG015F”相匹配的价格&库存,您可以联系我们找货
免费人工找货