UB215SKW01N-5C

Low Profile Pushbuttons Series UB2 Distinctive Characteristics Combination of PCB mountability and short body allows use in compact applications. Small behind panel dimension for snap-in mounting in tight spaces. Snap-acting contact mechanism provides sensitive actuation with audible feedback. Latchdown mechanism, independent of switching mechanism, gives visible, audible, and tactile indication of circuit status. Terminals are epoxy sealed to lock out flux, solvents, and other contaminants. Momentary and alternate action circuits available in the same space-saving body size. Illuminated models available and shown in Illuminated Pushbutton section. Matching indicators available and shown at the end of Section M. Actual Size N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Low Profile Pushbuttons Series UB2 General Specifications Electrical Capacity (Resistive Load) Power Level (code W): Logic Level (code G): 5A @ 125/250V AC or 5A @ 30V DC 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Note: Find additional explanation in Supplement section. Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Contact Timing: Travel: 50 milliohms maximum for silver; 100 milliohms maximum for gold 200 megohms minimum @ 500V DC 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts & case for 1 minute minimum 1,000,000 operations minimum for momentary; 200,000 operations minimum for alternate action 10,000 operations minimum for silver; 200,000 operations minimum for gold Single Pole: 1.90N Double Pole: 2.55N Break before make Pretravel .067” (1.7mm); Overtravel .024” (0.6mm); Total Travel .091” (2.3mm) Materials & Finishes Housing/Bezel: Snap-in Frame: Movable Contactor: Movable Contacts: Stationary Contacts: Terminals: Base: Glass fiber reinforced polyamide (UL94V-0) Stainless steel Phosphor bronze Silver alloy or copper with gold plating Silver alloy or copper with gold plating Phosphor bronze with silver or gold plating Glass fiber reinforced liquid crystal polymer (UL94V-0) Environmental Data Operating Temp Range: Humidity: Vibration: Shock: –25°C through +70°C (–4°F through +158°F) 90 ~ 95% humidity for 240 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Installation Processing Cap Installation Force: 15.0N maximum downward force on cap Soldering: Cleaning: Wave Soldering (PC version): See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section. These devices are not process sealed. Hand clean locally using alcohol based solution. Standards & Certifications Flammability Standards: UL & C-UL Recognized: UL94V-0 housing/bezel & base All single & double pole models recognized at 5A @ 125/250V AC or 0.014A @ 28V DC; UL File No. WOYR2.E44145 & C-UL File No. WOYR8.E44145; add “/U” to end of part number to order UL mark on switch & add “/U-C” to end of part number to order C-UL mark on switch (equivalent to CSA certification). R N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Low Profile Pushbuttons TYPICAL SWITCH ORDERING EXAMPLE Series UB2 N 5C CAP TYPES & COLORS Sculptured Cap Lens/Insert Colors 4JA 4JB 4JC 4JD 4JF Clear/Black Clear/White Clear/Red Clear/Amber Clear/Green Beveled Cap & Colors 5A 5B 5C 5D 5F Black White Red Amber Green UB2 POLES 1 2 SPDT DPDT 1 5 CIRCUITS 5 6 ON ON (ON) ON ( ) = Momentary Alternate Action with Latchdown SK G 03 CONTACTS & RATINGS W G Silver Rated 5A @ 125/250V AC Gold Rated 0.4VA max @ 28V AC/DC max MOUNTING TYPES PCB Mounting SK KK Square * Snap-in Mounting Square * Standard with Solder Lug terminals TERMINALS Solder Lug (for 01 Snap-in Mounting) IMPORTANT: Switches are supplied without UL & C-UL marking unless specified. Specific models & ratings noted on General Specifications page. 03 Straight PC DESCRIPTION FOR TYPICAL ORDERING EXAMPLE UB215SKG03N-5C Red Beveled Cap Note: Flat Cap with clear lens and colored diffuser available; see Illuminated Pushbuttons section Gold Contacts with 0.4VA Rating Square with PCB Mounting SPDT ON-(ON) Circuit Straight PC Terminals POLES & CIRCUITS Plunger Position ( ) = Momentary Normal Pole SP DP Model UB215 *UB216 UB225 *UB226 ON ON ON ON (ON) ON (ON) ON 1-3 1-3 4-6 1-2 1-2 4-5 Down Connected Terminals Normal Down Note: Throw & Schematics Switch is marked with NC, NO, COM, L+ & L–. 1 3 1 3 COM NO 6 NC COM 2 NO 4 NC COM 5 NO SPDT DPDT NC 2 * When in latchdown position for the alternate circuit, cap positions above the housing are: .059” (1.5mm) for snap-in models & .276” (7.0mm) for PCB models. N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Low Profile Pushbuttons MOUNTING TYPES & SHAPES PCB Mounting Series UB2 SK Square Single Pole (5.08) .200 3 Double Pole (5.08) Typ .200 6 3 2 1 (5.08) Typ .200 5 4 2 1 (5.08) Typ .200 C L (1.2) Dia Typ .047 C L (1.2) Dia Typ .047 Snap-in Mounting (Solder Lug) KK Square with Built-in Bezel (17.4) Sq .685 Panel Thickness: .039 ~ .126” (1.0 ~ 3.2mm) CONTACT MATERIALS & RATINGS W G Silver Contacts Power Level 5A @ 125V AC & 250V AC Gold Contacts Logic Level 0.4VA maximum @ 28V AC/DC maximum Complete explanation of operating range in Supplement section. T ERMINALS 01 Solder Lug (1.6) .063 (0.2) .008 (5.0) .197 03 Straight PC (2.0) .079 (0.8) .032 Thk = (0.5) .020 (0.2) .008 (4.0) .157 (1.0) .039 Thk = (0.5) .020 CAP TYPES & COLOR COMBINATIONS 4 AT3073 Sculptured (6.1) .240 5 AT3077 Beveled (5.6) .220 Lens/Insert Colors Available: Cap Colors Available: JA JB JC Clear/ Black Clear/ White Clear/ Red (15.0) Sq .591 A B Clear Lens Black White Red (15.0) Sq .591 JD JF Clear/ Amber Clear/ Green Opaque Colored Insert D F Amber Green Opaque Colored Cap 03-07 C Material: Polycarbonate Finish: Glossy Material: Polycarbonate Finish: Glossy N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com Low Profile Pushbuttons TYPICAL SWITCH DIMENSIONS Single Pole • PCB Mount (6.1) .240 Series UB2 3 (15.0) Sq .591 (0.5) Typ .020 (5.08) Typ .200 L+ N.C. 2 1 N.O. COM L– (15.24) Sq .600 (1.5) .059 (0.5) .020 (7.0) (10.0) (4.0) .276 .157 .394 Latchdown Position (1.0) .039 (5.08) .200 UB215SKG03N-4JC Double Pole • PCB Mount (6.1) .240 3 N.C. L+ N.C. 6 5 (15.0) Sq .591 2 1 N.O. COM. L– (5.08) Typ .200 N.O. COM. 4 (15.24) Sq .600 (1.5) .059 (0.5) .020 (7.0) (10.0) (4.0) .276 .157 .394 Latchdown Position (0.5) Typ .020 (1.0) Typ .039 (5.08) Typ .200 UB225SKG03N-4JC Single Pole • Snap-in Mount • Solder Lug (3.0) .118 (0.8) x (1.6) Typ .032 x .063 3 (15.0) Sq .591 (5.08) Typ .200 L+ N.C. 2 N.O. COM L– 1 (19.0) Sq .748 (1.5) .059 (1.4) .055 (15.5) (5.0) .610 .197 Latchdown Position (0.5) Typ .020 (2.0) .079 (5.08) .200 UB216KKW01N-4JC Double Pole • Snap-in Mount • Solder Lug (3.0) .118 (0.8) x (1.6) Typ .032 x .063 3 L+ N.C. N.C. 6 5 (15.0) Sq .591 2 1 N.O. COM. L– (5.08) Typ .200 N.O. COM. 4 (19.0) Sq .748 (1.5) .059 (1.4) .055 (15.5) (5.0) .610 .197 Latchdown Position (0.5) Typ .020 (2.0) Typ .079 (5.08) Typ .200 UB226KKW01N-4JC N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Low Profile Pushbuttons OPTIONAL ACCESSORIES Protective Guard for Snap-in Model AT4141 Opens 90° Closes manually Materials: Cover: Clear Polycarbonate Base: Black GFR Polyamide Recommended Panel Thickness: .039” ~ .106” (1.0mm ~ 2.7mm) Series UB2 (11.1) .437 (21.7) .854 Cap Height When Assembled (19.1) .752 (8.05) .317 (19.5) .768 (21.5) .846 (6.5) .256 (16.1) .634 (19.1) .752 Spring Loaded Protective Guard for Snap-in Mounting of PCB Model AT4170 Opens 180° Closes automatically Materials: Cover: Clear Polycarbonate Base: Black Polyamide Coil Spring: Stainless Steel Recommended Panel Thickness: .039” ~ .126” (1.0mm ~ 3.2mm) Recommended Panel-to-PCB Range: .531” ~ .622” (13.5mm ~ 15.8mm) (11.1) .437 (21.7) .854 (18.1) .713 (15.64) .616 (19.5) .768 (21.5) .846 (6.5) .256 (13.5) .531 (15.64) .616 (18.0) .709 180° (18.8) Sq .740 (40.0) Min* 1.575 AT4170 2 Protective Guard Panel (21.7) .854 Installation 1 Install switch onto PC board. 2 Snap protective guard into panel. 3 Join the two assemblies. 3 Switch PC Board 1 (13.5) ~ (15.8) .531 ~ .622 (21.5) .846 (21.5) .846 (N) (N) = Number of switches * Minimum dimension allows opening of cover to 180° Spring Loaded Protective Guard for Snap-in Model AT4142 Opens 180° Closes automatically Materials: Cover: Clear Polycarbonate Base: Black GFR Polyamide Coil Spring: Stainless Steel Recommended Panel Thickness: .039” ~ .106” (1.0mm ~ 2.7mm) (11.1) .437 (21.7) .854 (19.1) .752 (8.05) .317 Cap Height When Assembled (19.5) .768 (21.5) .846 (6.5) .256 (16.1) .634 (19.1) .752 N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Low Profile Pushbuttons OPTIONAL ACCESSORIES Dust Cover AT4145 Not for use with barriers. Series UB2 (17.1) .673 Materials: Lid: Clear PVC Operating temperature range: 0°C ~ +70°C (32°F ~ 158°C). Gasket: Polyethylene Recommended Panel Thickness .039” ~ .098” (1.0mm ~ 2.5mm) (17.0) Sq .669 (17.1) .673 (17.7) .697 Cap Height When Assembled (6.4) .252 (2.5) .098 (17.7) .697 (25.2) Sq .992 Barriers for Snap-in Mount AT4143 End AT4144 Center (4.1) Typ .161 (4.8) .189 (21.0) .827 (13.3) .524 (24.28) .956 A (20.07) .790 (17.4) .685 End Position Center Position (1.2) .047 (1.2) .047 Material: Polyamide (20.07) .790 Cutouts for more than 1 Switch: A = .799” (20.3mm) x Number of Switches + .051” (1.3mm) LEGENDS Easily create and submit your own legends using our new on-line Legend Maker. Visit www.nkkswitches.com For other legend support options, customers may either contact the factory and request the UB/UB2 Legend Packet, or utilize the general information and basic specifications presented below. Suggested Printable Area for UB Lens Recommended Methods: Laser Etch on clear lens; Screen Print or Pad Print on lens. Epoxy based ink is recommended. Beveled Cap Sculptured Cap N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com LM O O N (9.98) Sq .393 (11.5) Sq .453 (0.76) Typ .030 Shaded areas are printable areas. 03-07 N (12.96) Dia .510 (14.48) Dia .570 (0.76) Typ .030