UB216SKW015D-1JB

Series UB2 Toggles Low Profile Pushbuttons Rockers General Specifications Electrical Capacity (Resistive Load) Power Level (silver): Logic Level (gold): 5A @ 125/250V AC or 5A @ 30V DC 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Note: Find additional explanation of operating range in Supplement section. Pushbuttons Programmable Illuminated PB Other Ratings D Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Keylocks Nominal Operating Force: Contact Timing: Travel: 50 milliohms maximum for silver; 100 milliohms maximum for gold 200 megohms minimum @ 500V DC 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts & case for 1 minute minimum 1,000,000 operations minimum for momentary; 200,000 operations minimum for alternate action 10,000 operations minimum for silver; 200,000 operations minimum for gold Single Pole: 1.90N Double Pole: 2.55N Break before make Pretravel .067” (1.7mm); Overtravel .024” (0.6mm); Total Travel .091” (2.3mm) Glass fiber reinforced polyamide (UL94V-0) Stainless steel Phosphor bronze Silver alloy or copper with gold plating Silver alloy or copper with gold plating Phosphor bronze with silver or gold plating Brass with tin plating Glass fiber reinforced liquid crystal polymer (UL94V-0) –25°C through +50°C (–13°F through +122°F) for Illuminated –25°C through +70°C (–13°F through +158°F) for Nonilluminated 90 ~ 95% humidity for 240 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) 15.0N maximum downward force on cap Wave Soldering (PC version): See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section. These devices are not process sealed. Hand clean locally using alcohol based solution. UL94V-0 housing/bezel & base File No. E44145 All single & double pole models recognized at 5A @ 125/250V AC or 0.014A @ 28V DC. Add “/U” to end of part number to order UL mark on switch. Add “/CUL” to end of part number to order cULus mark on switch. UL recognized only when ordered switch body with cap assembled. Rotaries Materials & Finishes Housing/Bezel: Snap-in Frame: Movable Contactor: Movable Contacts: Stationary Contacts: Switch Terminals: Lamp Terminals: Base: Slides Tactiles Environmental Data Operating Temperature Range: Humidity: Vibration: Tilt Shock: Installation Touch Cap Installation Force: Soldering: Cleaning: Processing Indicators Standards & Certifications Flammability Standards: UL: Supplement Accessories D88 www.nkk.com Low Profile Pushbuttons Series UB2 Toggles Alternating legends (patent pending) in choice of sculptured or flat caps, combined with super bright bicolor LED. Combination of PCB mountability and short body allows use in compact applications. Small behind panel dimension for snap-in mounting in tight spaces. Snap-acting contact mechanism provides sensitive actuation with audible feedback; quick-make, quick-break characteristic limits arcing and prolongs electrical life. Latchdown mechanism, independent of switching mechanism, gives outstanding stability and reliability plus visible and tactile indication of circuit status. Terminals are epoxy sealed to lock out flux, solvents, and other contaminants. Momentary and alternate action circuits available in the same space-saving body size. Matching indicators available. D www.nkk.com D89 Supplement Accessories Indicators Actual Size Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Wide selection of illumination effects is achieved with single and bicolor, 1- or 6-element LEDs in flat, beveled, or sculptured caps. Rockers Distinctive Characteristics Series UB2 Toggles Low Profile Pushbuttons T YPICAL SWITCH Rockers UB2 Poles 1 2 SPDT DPDT 1 5 SK SK Mounting Types PCB Mounting Square Square G 03 Terminals Solder Lug* 01 (for Snap-in Mounting) 03 Straight PC Pushbuttons Circuits 5 ON ON (ON) ON * Snap-in Mounting KK * Standard with Solder Lug terminals Programmable Illuminated PB D ( ) = Momentary 6 Alternate Action with Latchdown Contacts & Ratings W G Silver Rated 5A @ 125/250V AC Gold Rated 0.4VA max @ 28V AC/DC max Rotaries Keylocks I MPORTANT: Switches are supplied without UL & cULus marking unless specified. Specific models & ratings noted on General Specifications page. Tilt Tactiles Slides * Wire harness & cable assemblies offered only in Americas Touch DESCRIPTION FOR TYPICAL ORDERING EXAMPLE UB215SKG035C-1JC Indicators Gold Contacts with 0.4VA Rating Square with PCB Mounting Straight PC Terminals Accessories Red, Bright LED and Sculptured Cap with Clear Lens and Red Diffuser SPDT ON-(ON) Circuit Supplement D90 www.nkk.com Low Profile Pushbuttons ORDERING EXAMPLE Series UB2 1JC Cap Types & Colors Sculptured Cap Lens/Diffuser Colors 1JB 1JC 1JD 1JF 2B 2C 2D 2F 3JB 3JC 3JD 3JF Clear/White Clear/Red Clear/Amber Clear/Green Beveled Cap & Colors White Red Amber Green Clear/White Clear/Red Clear/Amber Rotaries Pushbuttons Toggles LEDS Bright LED 5C 5D 5F Red Amber Green D Clear/Green Super Bright LED 6B 6F 6G White Green Blue Sculptured Cap Lens/Diffuser Color 1JB 2B 3JB Clear/White White Clear/White Beveled Cap & Color Flat Cap Lens/Diffuser Color Super Bright Bicolor LED 6CF Red/Green Sculptured Cap Lens/Diffuser Color 1JB 2B 3JB 4J 5J Clear/White Beveled Cap & Color Flat Cap Lens/Diffuser Color Clear/White Clear Lens Clear Lens 01 02 04 ON/OFF START/STOP OPEN/CLOSE Sculptured Cap with Alternating Legend Flat Cap with Alternating Legend Nonilluminated N Nonilluminated Sculptured Cap Lens/Insert Colors 4JA Clear/Black 4JD Clear/Amber 4JB Clear/White 4JF Clear/Green 4JC Clear/Red Beveled Cap & Colors 5A 5B 5C Black White Red www.nkk.com D91 5F Green Supplement 5D Amber Accessories Indicators Touch Alternating Legends Tilt White Tactiles Slides Keylocks Flat Cap Lens/Diffuser Colors Programmable Illuminated PB Rockers 5C Series UB2 Toggles Low Profile Pushbuttons POLES & CIRCUITS Plunger Position ( ) = Momentary Pole Model Normal Down Connected Terminals Normal Down Throw & Switch/Lamp Schematics Notes: Switch is marked with NC, NO, COM, L+ & L–. Lamp circuit is isolated and requires an external power source. 1 COM (+) (-) Pushbuttons Rockers SP UB215 *UB216 UB225 *UB226 ON ON ON ON (ON) ON (ON) ON 1-3 1-2 SPDT 1 3 COM NC 2 NO 4 COM (+) (-) Programmable Illuminated PB DP 1-3 4-6 1-2 4-5 DPDT D 3 NC 2 NO 6 NC 5 NO * When in latchdown position for the alternate circuit, cap positions above the housing are: .059” (1.5mm) for snap-in models & .276” (7.0mm) for PCB models. MOUNTING TYPES & SHAPES PCB Mounting SK Keylocks Square SP, Single Color LED (5.08) .200 L (+) DP, Single Color LED (5.08) Typ .200 6 L (+) SP, Bicolor LED (5.08) .200 LC+ DP, Bicolor LED (5.08) Typ .200 6 LC+ 3 (2.54) Typ .100 (10.16) .400 (1.2) Dia Typ .047 3 (2.54) Typ .100 (10.16) .400 (1.2) Dia Typ .047 3 (2.54) Typ .100 (10.16) .400 (1.2) Dia Typ .047 3 (2.54) Typ .100 (10.16) .400 (1.2) Dia Typ .047 (5.08) .200 2 L (–) 1 (5.08) .200 5 L (–) 4 2 1 (5.08) .200 (2.54) .100 2 L2L11 (5.08) .200 5 L24 L1- 2 1 Rotaries C L C L C L (2.54) .100 C L Slides Snap-in Mounting (Solder Lug) KK Square with Built-in Bezel (17.4) Sq .685 Tactiles Panel Thickness: .039 ~ .126” (1.0 ~ 3.2mm) CONTACT MATERIALS & RATINGS Tilt W G Silver Contacts Power Level 5A @ 125V AC & 250V AC Touch Gold Contacts Logic Level 0.4VA maximum @ 28V AC/DC maximum Complete explanation of operating range in Supplement section. Indicators S WITCH & LAMP TERMINALS 01 Solder Lug For Switch & Bright LED (0.2) .008 (1.6) .063 (5.0) .197 (1.0) .039 Thk = (0.5) .020 Accessories For Super Bright & Bicolor LED (0.2) .008 (4.0) .157 03 Straight PC For Switch & Bright LED (0.2) .008 (4.0) .157 (1.0) .039 Thk = (0.5) .020 For Super Bright & Bicolor LED (0.2) .008 (4.0) .157 (1.0) .039 Thk = (0.5) .020 Supplement (2.0) .079 (0.8) .032 Thk = (0.5) .020 D92 www.nkk.com Low Profile Pushbuttons BRIGHT LED & CAPS Series UB2 Toggles The electrical specifications shown are determined at a basic temperature of 25°C. LED circuit is isolated and requires an external power source. Polarity marks are on the bottom of the switch. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement section. The LED is an integral part of the switch and not available separately. Electrical Specifications for Bright LED Color Forward Peak Current Continuous Forward Current Forward Voltage Reverse Peak Voltage Current Reduction Rate Above 25°C Ambient Temperature Range IFM IF VF VRM ∆IF Red 30 20 1.85 5 0.40 Amber 30 20 2.0 5 0.42 –25° ~ +50° Green 25 20 2.1 5 0.46 Unit mA mA V V mA/°C °C D Bright Single Color LED with 1 element Caps for Bright LED (+) (-) 1 AT3074 Sculptured (6.1) .240 2 AT3075 Beveled (5.6) .220 3 AT3076 Flat (5.6) .220 (15.0) Sq .591 (15.0) Sq .591 (15.0) Sq .591 Clear Lens Translucent Colored Diffuser Lens/Diffuser Colors Available: Translucent Colored Cap Cap Colors Available: Clear Lens Translucent Colored Diffuser Lens/Diffuser Colors Available: JB JC JD JF Clear/White Clear/Red Clear/Amber Clear/Green B C D F White Red Amber Green Finish: Glossy JB JC JD JF Clear/White Clear/Red Clear/Amber Clear/Green Material: Polycarbonate www.nkk.com D93 Supplement Accessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB 5C 5D 5F Pushbuttons Rockers Series UB2 Toggles Low Profile Pushbuttons SUPER BRIGHT LEDS & CAPS Rockers The electrical specifications shown are determined at a basic temperature of 25°C. LED circuit is isolated and requires an external power source. Polarity marks are on the bottom of the switch. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement section. The LED is an integral part of the switch and not available separately. Pushbuttons Electrical Specifications for Super Bright LEDS Super Bright LEDs are Electrostatic Sensitive ATTENTION Programmable Illuminated PB ELECTROSTATIC SENSITIVE DEVICES 6B Color IFM IF VF VRM ∆I F White 25 20 3.6 5 0.40 6F Green 25 20 3.5 5 0.40 –25° ~ +50° 6G Blue 25 20 3.6 5 0.40 Unit mA mA V V mA/°C °C D Forward Peak Current Continuous Forward Current Forward Voltage Reverse Peak Voltage Current Reduction Rate Above 25°C Ambient Temperature Range Keylocks Super Bright Single Color LED with 1 element Caps for Super Bright LED (+) (-) Rotaries 1JB AT3074JB Sculptured Clear Lens/White Diffuser (6.1) .240 2B AT3075B Beveled White Cap (5.6) .220 3JB AT3076JB Flat Clear Lens/White Diffuser (5.6) .220 Slides (15.0) Sq .591 (15.0) Sq .591 (15.0) Sq .591 Tactiles Clear Lens Translucent White Diffuser Material: Polycarbonate Translucent White Cap Finish: Glossy Clear Lens Translucent White Diffuser Tilt S UPER BRIGHT BICOLOR LED & CAPS Electrical Specifications for Super Bright Bicolor LED Touch The electrical specifications shown are determined at a basic temperature of 25°C. LED circuit is isolated and requires an external power source. Polarity marks are on bottom of switch. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in Supplement Section. The LED is an integral part of the switch and not available separately. Super Bright LEDs are Electrostatic Sensitive ELECTROSTATIC SENSITIVE DEVICES ATTENTION 6CF Color I FM IF VF VRM ∆I F Red/Green 30/25 (25/22 for Amber) 20/20 2.1/3.5 4/4 0.40/0.33 –25° ~ +50° Unit mA mA V V mA/°C °C Indicators Forward Peak Current Continuous Forward Current Forward Voltage Reverse Peak Voltage Current Reduction Rate Above 25°C Ambient Temperature Range L1 (-) Red L2 (-) Green Supplement Accessories Super Bright Bicolor LED with 2 elements D94 LC (+) Amber color is achieved by lighting red and green simultaneously, but is not suitable for Alternating Legends. www.nkk.com Low Profile Pushbuttons Caps for Super Bright Bicolor LED AT3074JB Sculptured Clear Lens/White Diffuser AT3075B Beveled White Cap Series UB2 2B (6.1) .240 1JB 3JB (5.6) .220 AT3076JB Flat Clear Lens/White Diffuser (5.6) .220 Clear Lens Translucent White Diffuser (15.0) Sq .591 (15.0) Sq .591 Clear Lens Translucent White Diffuser (15.0) Sq .591 Material: Polycarbonate Finish: Glossy D Alternating Legend Caps for Super Bright Bicolor LED 4J AT3069J Sculptured Cap with Alternating Legend (6.1) .240 5J AT3070J Flat Cap with Alternating Legend (5.6) .220 Clear Lens Alternating Legend Filter (15.0) Sq .591 Clear Lens Alternating Legend Filter Finish: Glossy (15.0) Sq .591 Material: Polycarbonate Standard Alternating Legend Pairs 01 Green Red Green Red Green Red Cap illumination is alternating green/red; legend text is black. Contact factory for other Alternating Legends. Legend illustrations are approximate representations of the actual characters on the filters. Tactiles (5.6) .220 (15.0) Sq .591 CAP TYPES & COLOR COMBINATIONS FOR NONILLUMINATED AT3073 Sculptured (6.1) .240 AT3077 Beveled JA JB JC JD JF (15.0) Sq .591 Clear/Black Clear/White Clear/Red Clear/Amber Clear/Green Material: Polycarbonate Finish: Glossy Clear Lens Opaque Colored Insert A B C D F Black White Red Amber Green Material: Polycarbonate Finish: Glossy D95 Opaque Colored Cap www.nkk.com Supplement Accessories Indicators Lens/Insert Colors Available: Cap Colors Available: Touch 4 5 Tilt No Code No Lamp Slides ON OFF 02 START STOP 04 OPEN CLOSE Rotaries Keylocks Programmable Illuminated PB Translucent White Cap Pushbuttons Rockers Toggles FFFFFFFFFFFFFFFFFFFFFFFFFFFFF N N N N N N N N N N O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O OFFFFFFFFFFFFFFFFFFFFFFFFFF EEEEEEEEEEEEEEEEE OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOEEEEEEESSSSSSSSSSSSSSSSSSSSNNNNNNN OOOOOOCCCCCCCCCCCCCCCCCCCCCCCCCCCCCLLLLLLLLLLLLLLLLLLLLLLLLLLLLLPPPPP Series UB2 Toggles Low Profile Pushbuttons TYPICAL SWITCH DIMENSIONS Bright & Super Bright LED Straight PC Rockers (15.0) Sq .591 (6.1) .240 3 (5.08) Typ .200 (5.08) Typ .200 L+ 3 L+ N.C. 6 5 N.O. COM N.C. 2 N.O. COM L– (5.08) .200 N.C. 2 N.O. COM L– (5.08) .200 1 1 4 Pushbuttons (15.24) Sq .600 (1.5) .059 (0.5) .020 (7.0) (10.0) (4.0) .157 .276 .394 Latchdown Position (2.54) Typ .100 (0.5) Typ .020 (4.0) .157 (2.54) Typ .100 (0.5) Typ (1.0) Typ .020 .039 (5.08) .200 (1.0) .039 (1.0) Typ .039 (5.08) Typ .200 Programmable Illuminated PB UB215SKG035C-1JC Bright Single Color LED (6.1) .240 Super Bright Single Color LED (1.0) .039 3 Single Pole Double Pole (1.0) .039 3 LC N.C. D Bicolor LED Straight PC (15.0) Sq .591 (5.08) Typ .200 (1.0) .039 (2.54) Typ .100 (0.5) Typ .020 LC N.C. L2 6 5 N.C. N.C. 2 N.O. COM L1 N.O. COM (5.08) .200 2 L2 N.O. COM L1 N.O. COM (5.08) .200 1 1 4 (15.24) Sq .600 Keylocks (1.5) .059 (0.5) .020 (7.0) (10.0) (4.0) .276 .394 .157 Latchdown Position (1.0) .039 (2.54) .100 (5.08) .200 (2.54) .100 (1.0) Typ .039 (5.08) Typ .200 UB225SKG03CF-1JB Bicolor LED Side View (3.0) .118 (0.8) x (1.6) Typ .032 x .063 Single Pole Double Pole Bright LED Solder Lug Rotaries (15.0) Sq .591 3 (5.08) Typ .200 L+ 3 L+ 6 N.C. N.C. 2 N.O. COM L– (5.08) .200 N.C. 2 N.O. COM L– 5 N.O. COM (5.08) .200 1 1 4 Slides (19.0) Sq .748 (1.5) .059 (1.4) .055 (15.5) (5.0) .610 .197 Latchdown Position (2.54) Typ .100 (0.5) Typ .020 (2.0) Typ .079 (5.08) .200 (2.0) Typ .079 (5.08) Typ .200 Tactiles UB216KKW015F-1JF Single Color LED Side View (3.0) .118 (0.8) x (1.6) Typ .032 x .063 Single Pole Double Pole Super Bright LED Solder Lug 3 (15.0) Sq .591 Tilt (5.08) Typ .200 L+ 3 N.C. L+ 6 N.C. N.C. 2 N.O. COM L– (5.08) .200 2 N.O. COM L– 5 N.O. COM (5.08) .200 1 1 4 (19.0) Sq .748 (1.5) .059 (1.4) (4.0) .055 .157 (15.5) (5.0) .610 .197 Latchdown Position Touch (2.54) Typ .100 (0.5) Typ .020 (2.0) .079 (1.0) .039 (5.08) .200 (2.0) Typ .079 (1.0) Typ .039 (5.08) Typ .200 UB226KKW016F-1JF Indicators Single Color LED Side View (3.0) .118 (0.8) x (1.6) Typ .032 x .063 Single Pole (1.0) .039 3 LC N.C. L2 Double Pole (1.0) .039 3 LC N.C. Bicolor LED Solder Lug 6 5 Accessories (15.0) Sq .591 (5.08) Typ .200 (1.0) .039 N.C. 2 N.O. COM L1 N.O. COM (5.08) .200 N.C. 2 L2 N.O. COM L1 N.O. COM (5.08) .200 1 1 4 Supplement (19.0) Sq .748 (1.5) .059 (1.4) (4.0) .055 .157 (15.5) (5.0) .610 .197 Latchdown Position (2.54) Typ .100 (0.5) Typ .020 (2.0) .079 (2.54) .100 (5.08) .200 (2.0) Typ .079 (2.54) .100 (5.08) .200 UB216KKW01CF-1JB D96 Bicolor LED Side View www.nkk.com Single Pole Double Pole Low Profile Pushbuttons OPTIONAL ACCESSORIES Protective Guard for Snap-in Model Opens 90° Closes manually (11.1) .437 Series UB2 Toggles (19.1) .752 (8.05) .317 Cap Height When Assembled (6.5) .256 (16.1) .634 (19.1) .752 Materials: Cover: Clear Polycarbonate Base: Black GFR Polyamide (21.7) .854 (19.5) .768 Recommended Panel Thickness: .039” ~ .106” (1.0mm ~ 2.7mm) (21.5) .846 D Spring Loaded Protective Guard for Snap-in Mounting of PCB Model AT4170 Opens 180° Closes automatically (11.1) .437 (21.7) .854 (18.1) .713 (15.64) .616 Materials: Base: Black Polyamide Coil Spring: Stainless Steel (19.5) .768 (21.5) .846 (6.5) .256 (13.5) .531 (15.64) .616 (18.0) .709 Recommended Panel Thickness: .039” ~ .126” (1.0mm ~ 3.2mm) Recommended Panel-to-PCB Range: .531” ~ .622” (13.5mm ~ 15.8mm) 180° (40.0) Min* 1.575 AT4170 2 Panel (21.7) .854 Installation 1 Install switch onto PC board. (21.5) .846 (N) 3 Switch 1 (21.5) .846 (N) = Number of switches * Minimum dimension allows opening of cover to 180° 3 Join the two assemblies. www.nkk.com D97 Supplement 2 Snap protective guard into panel. PC Board Accessories Indicators Protective Guard Touch (18.8) Sq .740 (13.5) ~ (15.8) .531 ~ .622 Tilt Tactiles Slides Cover: Clear Polycarbonate Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers AT4141 Series UB2 Toggles Low Profile Pushbuttons OPTIONAL ACCESSORIES Spring Loaded Protective Guard for Snap-in Model Rockers Pushbuttons AT4142 Opens 180° Closes automatically Programmable Illuminated PB Materials: D Cover: Clear Polycarbonate Base: Black GFR Polyamide Coil Spring: Stainless Steel (11.1) .437 (21.7) .854 (19.1) .752 (8.05) .317 Cap Height When Assembled Recommended Panel Thickness: .039” ~ .106” (1.0mm ~ 2.7mm) (19.5) .768 (21.5) .846 (6.5) .256 (16.1) .634 (19.1) .752 Keylocks Dust Cover AT4145 Materials: Lid: Clear PVC Operating temperature range: 0°C ~ +70°C (32°F ~ 158°C). Gasket: Polyethylene Not for use with barriers. (17.1) .673 Slides Rotaries (17.0) Sq .669 (17.1) .673 (17.7) .697 Tactiles Recommended Panel Thickness .039” ~ .098” (1.0mm ~ 2.5mm) Cap Height When Assembled (6.4) .252 (2.5) .098 (17.7) .697 (25.2) Sq .992 Tilt Barriers for Snap-in Mount AT4143 End AT4144 Center (4.1) Typ .161 Touch (24.28) .956 (20.07) .790 A Indicators (4.8) .189 (21.0) .827 (13.3) .524 (17.4) Min .685 Accessories End Position Center Position (1.2) .047 (20.07) .790 (1.2) .047 Cutouts for more than 1 Switch: A = .799” (20.3mm) x Number of Switches + .051” (1.3mm) Supplement Material: Polyamide D98 www.nkk.com Low Profile Pushbuttons LEGENDS Series UB2 Toggles Suggested Printable Area for UB2 Lens, Film Insert or Diffuser Recommended Methods: Laser Etch on clear lens, Screen Print or Pad Print on lens; Laser Print on film insert. Shaded areas are printable areas. Beveled Cap Flat Cap Sculptured Cap D Lens Lens Lens (13.5) Sq .531 (15.0) Sq .591 (0.76) Typ .030 Film Insert Diffuser Lens (12.96) Dia .510 (14.48) Dia .570 (0.76) Typ .030 (0.5) R .020 (0.5) R .020 (9.98) Sq .393 (11.5) Sq .453 Film Insert: Clear Polyester 4 mil maximum thickness www.nkk.com D99 Supplement Accessories Indicators Touch Tilt Tactiles (11.88) Sq .468 (13.4) Sq .528 (0.76) Typ .030 (11.88) Dia .468 (13.4) Sq .528 (0.76) Typ .030 Slides (0.76) Typ .030 Film Insert or Diffuser Film Insert or Diffuser Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers NKK Switches can provide custom legends for caps. Contact factory for more information. O N OF F