Environmentally Sealed Pushbuttons
Series WB
Distinctive Characteristics
Single unit construction of the bushing and case gives added protection from environmental elements. Specially designed contact mechanism for breaking light welds.
Minimal contact bounce is achieved with specially designed interlocked switching mechanism.
Outer housing of heat resistant resin meets UL 94V-0 flammability standard and provides high arc and tracking resistance.
Solder lug and screw terminal models meet IP67 of IEC60529 Standards at front panel (dust tight and water protected for temporary immersion). Behind panel standard is IP60 (dust tight but not water protected).
Wire lead models conform fully to IP67 of IEC60529 Standards at front and behind panel (dust tight and water protected for temporary immersion). These models are epoxy sealed at the switch base and covered by an outer case for further protection from dust and water (not operable under water).
Actual Size
N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
02-08
Environmentally Sealed Pushbuttons
Series WB
General Specifications
Electrical Capacity (Resistive Load)
Power Level: 6A @ 125V AC & 3A @ 250V AC or 6A @ 30V DC
Other Ratings
Contact Resistance:
Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Contact Timing: Total Travel:
10 milliohms maximum for solder lug & screw terminal models 30 milliohms maximum for wire lead terminal models 200 megohms minimum @ 500V DC 1,500V AC minimum for 1 minute minimum 30,000 operations minimum 15,000 operations minimum Break before make Alternate Action .177” (4.5mm); Momentary Action .110” (2.8mm)
Materials & Finishes
Plunger: Bushing & Outer Case: Inner Case: Inner Sealing Ring: Outer Sealing Ring: Movable Contactor: Movable Contacts: Stationary Contacts: Terminals: Wire Lead Covers:
Brass with nickel plating Fiberglass reinforced polyamide (UL94V-0 outer case) Melamine Silicone rubber Natural rubber Copper with silver plating Silver alloy with silver plating Silver alloy with silver plating Brass with silver plating for screw lug models; brass with tin plating for solder lug & wire lead models Heat resistant polyvinyl chloride (Leads are AWG 16.)
Environmental Data
Operating Temp Range: Humidity: Vibration: Shock:
–30°C through +70°C (–22°F through +158°F) 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Installation
Mounting Torque: Soldering Time & Temp:
1 .5Nm (13 lb • in) Manual Soldering: See Profile A in Supplement section.
Standards & Certifications
Flammability Standards: Wiring Material Standards:
UL94V-0 outer case UL AWM 1015 Recognized at Flammability VW-1; Temperature Range –20°C ~ +105°C; Maximum Load 600V; AWG 16 CSA TEW 105 Certified at Temperature Range –20°C ~ +105° C; Maximum Load 600V
N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
02-08
Environmentally Sealed Pushbuttons
TYPICAL SWITCH ORDERING EXAMPLE
Series WB A
CAP COLORS
A B C *D *E F *G Black White Red Amber Yellow Green Blue Gray
WB
POLES
1 SPDT
1
2
S T L
S
T ERMINALS
Solder Lug Screw Lug Wire Lead D E
D
CAPS
.520” (13.2mm) Dia. .748” (19.0mm) Dia.
CIRCUITS
2 5 ON ON ON (ON)
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
WB12S-DA
Black .520” (13.2mm) Dia. Cap SPDT ON-ON Circuit Solder Lug Terminals
( ) = Momentary
*H
* Not available with cap code E
POLES & CIRCUITS
Actuator Position ( ) = Momentary Pole Model Normal
Flat
Connected Terminals Normal
Flat
Throw & Schematics Note: Terminal numbers are not actually on wire lead models.
1 (COM)
Down
Down
SP SP
WB12 WB15
ON ON
ON (ON)
1-1b 1-1b
1-1a 1-1a
SPDT
1a
1b
STANDARD WIRE COLOR SCHEME
Wire leads are covered with heat resistant vinyl in accordance to UL 1015 and CSA TEW 105 Standards for Appliance Wiring Material (AWM). Terminal Numbers & Wire Colors Models WB12L, WB15L 1a White 1 Black 1b Red
TYPICAL SWITCH DIMENSIONS
Solder Lug
Flatted (0.8) Typ .031 (13.2) Dia .520
1b 1
(28.8) 1.134
(11.2) .441 (12.5) Dia .492
(2.4) Dia Typ .094 M12 P1 (11.0) .433 (15.8) .622
1a
(1.0) .039 (9.6) .378 (33.0) 1.299
(4.8) .189
(4.8) .189 (19.4) .764
Panel Thickness .157” (4.0mm)
WB15S-DA N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 02-08
Environmentally Sealed Pushbuttons
TYPICAL SWITCH DIMENSIONS
Screw Lug
M3.5 x 5 Flatted
Series WB
1b
(13.2) Dia .520
(6.6) .260
1 1a
(28.8) 1.134
(11.2) .441 (12.5) Dia .492
M12 P1 (11.0) .433 (15.8) .622
(1.0) .039 (9.6) .378 (36.5) 1.437
(8.3) .327
(1.0) .039 (19.4) .764
Panel Thickness .157” (4.0mm)
WB12T-DA
Wire Lead
Flatted
1b
(13.2) Dia .520
1
(30.2) 1.189
(11.2) .441 (12.5) Dia .492
1a
M12 P1 (11.0) .433 (15.8) .622
(9.6) .378
(1.0) .039
(38.0) 1.496
(10.0) .394 (200.0) + (20.0) 7.874
(20.8) .819
Panel Thickness .157” (4.0mm)
WB12L-DA
CAPS & CAP COLORS D
AT414 .520” (13.2mm) Diameter
(12.8) Dia .504
E
AT412 .748” (19.0mm) Diameter
Colors Available: ABCDEFGH Material: PBT Cap Color Codes: Finish: Glossy
M3.5 P0.6
(11.0) .433 (14.9) .587
Colors Available: ABCF Material: Polystyrene Finish: Glossy
M3.5 P0.6
(8.0) .315 (11.7) .461
(13.2) Dia .520
(19.0) Dia .748
A
Black
B
White
C
Red
D
Amber
E
Yellow
F
Green
G
Blue
H
Gray
STANDARD HARDWARE
AT503M Hex Face Nut Material: Brass with chrome plating 1 supplied with each switch
M12 P1
AT508 Internal Tooth Lockwasher
(14.3) .563
(12.1) .476
AT401P O-ring
(15.8) Dia .622
Material: Steel with zinc/chromate 1 supplied with each switch
Material: Natural rubber 1 supplied with each switch
(12.1) Dia .476 (17.5) Dia .689
(13.8) Dia .543
(16.0) .630
(2.4) .094
(1.0) .039
(0.5) .020
(1.5) .059
N KK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
02-08
很抱歉,暂时无法提供与“WB12S-DA”相匹配的价格&库存,您可以联系我们找货
免费人工找货