CF5006AKA-1

SM5006 series Crystal Oscillator Module ICs OVERVIEW The SM5006 series are crystal oscillator module ICs, that incorporate high-frequency, low current consumption oscillator and output buffer circuits. Highly accurate thin-film feedback resistors and high-frequency capacitors are built-in, eliminating the need for external components to make a stable 3rd overtone oscillator. FEATURES I I I I I I Up to 107MHz operation Capacitors CG, CD built-in Inverter amplifier feedback resistor built-in TTL input level 16mA (VDD = 4.5V) drive capability 4mA (VDD = 4.5V) drive capability (5006AH×) I I I I I Output three-state function 2.7 to 5.5V supply voltage Oscillator frequency output 8-pin SOP (SM5006×××S) Chip form (CF5006×××) SERIES CONFIGURATION 3V operating Version*1 gm ratio Output load (max) [pF] − − 15 15 15 − 15 15 15 15 15 15 15 − − − − − − − − − − − Recommended operating frequency range*2 [MHz] − − 22 to 30 30 to 50 50 to 70 − 22 to 30 30 to 40 50 to 70 22 to 70 22 to 70 22 to 40 22 to 70 − − − − − − − − − − − Output load (max) [pF] 50 50 50 50 30 (15)*4 30 (15)*4 15 50 15 15 15 50 30 (15)*4 15 50 15 50 15 15 15 15 15 15 15 15 15 15 15 5V operating Recommended operating frequency range*2 [MHz] 22 to 30 30 to 40 40 to 60 50 to 70 70 to 100 80 to 107 40 to 60 40 to 50 50 to 70 70 to 100 22 to 100 22 to 70 70 to 107 22 to 70 22 to 50 22 to 100 22 to 70 22 to 30 30 to 40 40 to 60 50 to 70 50 to 70 22 to 70 22 to 70 22 to 30 30 to 40 40 to 60 50 to 70 Output waveform*3 tr /tf [ns] 8/8 8/8 7/7 7/7 6/6 6/6 8/8 8/8 7/7 7/7 6/6 8/8 7/7 4/4 4/4 4/4 4/4 4/4 4/4 4/4 7/7 7/7 7/7 7/7 Built-in capacitance CG [pF] 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 CD [pF] 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 Rf [kΩ] 8.2 5.6 4.9 2.6 2.6 2.6 4.9 2.6 2.6 No No No No 8.2 5.6 4.9 2.6 2.6 No No 8.2 5.6 4.9 2.6 Input level Output duty level CMOS CMOS CMOS CMOS CMOS CMOS CMOS CMOS CMOS CMOS CMOS CMOS CMOS TTL TTL TTL TTL TTL TTL TTL CMOS CMOS CMOS CMOS SM5006ANAS SM5006ANBS SM5006ANCS SM5006ANDS SM5006ANES SM5006ANFS SM5006CNCS SM5006CNDS SM5006CNES SM5006BNCS SM5006BNES SM5006DNCS SM5006DNES SM5006AKAS SM5006AKBS SM5006AKCS SM5006AKDS SM5006CKDS SM5006BKCS SM5006DKCS SM5006AHAS SM5006AHBS SM5006AHCS SM5006AHDS 0.5 1 2 2 3 4 2 2 3 2 3 2 3 0.5 1 2 2 2 2 2 0.5 1 2 2 TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL *1. Chip form devices have designation CF5006×××. *2. The recommended operating frequency is a yardstick value derived from the crystal used for NPC characteristics authentication. However, the oscillator frequency band is not guaranteed. Specifically, the characteristics can vary greatly due to crystal characteristics and mounting conditions, so the oscillation characteristics of components must be carefully evaluated. *3. 5006×N×: CL = 50pF, CMOS load, 5006×K×: CL = 15pF, 10TTL load, 5006AH×: CL = 15pF, CMOS load *4. SOP package only SEIKO NPC CORPORATION —1 SM5006 series ORDERING INFORMATION Device SM5006×××S CF5006×××–1 Package 8-pin SOP Chip form PACKAGE DIMENSIONS (Unit: mm) • 8-pin SOP 0.15 + 0.1 − 0.05 4.4 0.2 6.2 0.3 0.695typ 5.2 0.3 0.05 0.05 1.5 0.1 1.27 0.4 0.2 0.10 0.4 0.1 0.12 M 0 to 10 SEIKO NPC CORPORATION —2 SM5006 series PAD LAYOUT (Unit: µm) PINOUT (Top view) VDD Q (920,1310) Y (0,0) INHN XT XTN VSS X Chip size: 0.92 × 1.31mm Chip thickness: 300 ± 30µm Chip base: VDD level PIN DESCRIPTION and PAD DIMENSIONS Number 1 2 3 4 5 6 7 8 Name INHN XT XTN VSS Q NC NC VDD I/O I I O – O – – – Description Output state control input. High impedance when LOW. Pull-up resistor built in Amplifier input. Amplifier output. Ground Output. Output frequency (fO) No connection No connection Supply voltage Crystal oscillator connection pins. Crystal oscillator connected between XT and XTN Pad dimensions [µm] X 195 385 575 766 765 – – 162 Y 212 212 212 212 1152 – – 1152 BLOCK DIAGRAM VDD VSS XTN RG CG Rf RD CD XT INHN HA5006 INHN XT XTN VSS 1 2 3 4 8 7 6 5 VDD NC NC Q Q SEIKO NPC CORPORATION —3 SM5006 series SPECIFICATIONS Absolute Maximum Ratings VSS = 0V Parameter Supply voltage range Input voltage range Output voltage range Operating temperature range Storage temperature range Symbol VDD VIN VOUT Topr Chip form Tstg 8-pin SOP 5006×N×, ×K× 5006AH× 8-pin SOP Condition Rating −0.5 to 7.0 −0.5 to VDD + 0.5 −0.5 to VDD + 0.5 −40 to 85 −65 to 150 −55 to 125 25 mA 10 500 mW Unit V V V °C °C Output current Power dissipation IOUT PD SEIKO NPC CORPORATION —4 SM5006 series Recommended Operating Conditions SM5006 series (package form) VSS = 0V Rating Parameter Symbol Series Condition min f ≤ 50MHz, CL = 50pF ANA, ANB, CNC, CND, DNC f ≤ 70MHz, CL = 15pF f ≤ 40MHz, CL = 15pF f ≤ 70MHz, CL = 50pF ANC, AND, BNC, CNE, DNE f ≤ 100MHz, CL = 15pF f ≤ 50MHz, CL = 15pF f ≤ 70MHz, CL = 15pF Supply voltage VDD ANE, ANF, BNE f ≤ 100MHz, CL = 15pF f ≤ 107MHz, CL = 15pF f ≤ 50MHz, CL = 15pF f ≤ 70MHz, CL = 15pF AKA, AKB, AKC, CKD, DKC AKD, BKC AHA, AHB, AHC, AHD Input voltage VIN All series f ≤ 50MHz, CL = 50pF, 4.5 ≤ VDD ≤ 5.5 ANA, ANB, CNC, CND, DNC f ≤ 70MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 f ≤ 40MHz, CL = 15pF, 2.7 ≤ VDD ≤ 3.6 f ≤ 50MHz, CL = 50pF, 4.5 ≤ VDD ≤ 5.5 f ≤ 70MHz, CL = 50pF, 4.5 ≤ VDD ≤ 5.5 ANC, AND, BNC, CNE, DNE f ≤ 70MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 f ≤ 100MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 f ≤ 50MHz, CL = 15pF, 2.7 ≤ VDD ≤ 3.6 f ≤ 70MHz, CL = 15pF, 3.0 ≤ VDD ≤ 3.6 Operating temperature TOPR ANE, ANF, BNE f ≤ 70MHz, CL = 50pF, 4.5 ≤ VDD ≤ 5.5 f ≤ 100MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 f ≤ 107MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 f ≤ 50MHz, CL = 15pF, 2.7 ≤ VDD ≤ 3.6 f ≤ 70MHz, CL = 15pF, 3.0 ≤ VDD ≤ 3.6 AKA, AKB, AKC, CKD, DKC AKD, BKC AHA, AHB, AHC, AHD f ≤ 50MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 f ≤ 70MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 f ≤ 50MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 f ≤ 70MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 f ≤ 50MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 f ≤ 70MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 f ≤ 70MHz, CL = 15pF f ≤ 70MHz, CL = 15pF f ≤ 70MHz, CL = 15pF 4.5 4.5 2.7 4.5 4.5 2.7 3.0 4.5 4.5 2.7 3.0 4.5 4.5 4.5 VSS − 40 0 − 10 − 40 − 20 − 40 0 − 20 − 20 − 20 − 40 − 20 − 20 − 20 − 40 0 − 40 − 20 − 40 − 15 typ – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – max 5.5 5.5 3.6 5.5 5.5 V 3.6 3.6 5.5 5.5 V 3.6 3.6 5.5 5.5 5.5 VDD + 85 + 70 + 70 + 80 + 80 + 85 + 70 + 80 + 80 + 80 + 85 + 80 + 80 + 80 + 85 + 70 + 85 + 80 + 85 + 75 °C °C °C °C V V V V V Unit °C °C SEIKO NPC CORPORATION —5 SM5006 series CF5006 series (chip form) VSS = 0V Rating Parameter Symbol Series Condition min f ≤ 50MHz, CL = 50pF ANA, ANB, CNC, CND, DNC f ≤ 70MHz, CL = 15pF f ≤ 40MHz, CL = 15pF f ≤ 70MHz, CL = 50pF ANC, AND, BNC, CNE, DNE f ≤ 100MHz, CL = 15pF f ≤ 50MHz, CL = 15pF f ≤ 70MHz, CL = 15pF Supply voltage VDD ANE, ANF, BNE f ≤ 70MHz, CL = 50pF f ≤ 107MHz, CL = 30pF f ≤ 50MHz, CL = 15pF f ≤ 70MHz, CL = 15pF AKA, AKB, AKC, CKD, DKC AKD, BKC AHA, AHB, AHC, AHD Input voltage VIN All series f ≤ 50MHz, CL = 50pF, 4.5 ≤ VDD ≤ 5.5 ANA, ANB, CNC, CND, DNC f ≤ 70MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 f ≤ 40MHz, CL = 15pF, 2.7 ≤ VDD ≤ 3.6 f ≤ 70MHz, CL = 50pF, 4.5 ≤ VDD ≤ 5.5 ANC, AND, BNC, CNE, DNE f ≤ 100MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 f ≤ 50MHz, CL = 15pF, 2.7 ≤ VDD ≤ 3.6 f ≤ 70MHz, CL = 15pF, 3.0 ≤ VDD ≤ 3.6 f ≤ 70MHz, CL = 50pF, 4.5 ≤ VDD ≤ 5.5 Operating temperature TOPR f ≤ 100MHz, CL = 30pF, 4.5 ≤ VDD ≤ 5.5 ANE, ANF, BNE f ≤ 107MHz, CL = 30pF, 4.5 ≤ VDD ≤ 5.5 f ≤ 50MHz, CL = 15pF, 2.7 ≤ VDD ≤ 3.6 f ≤ 70MHz, CL = 15pF, 3.0 ≤ VDD ≤ 3.6 AKA, AKB, AKC, CKD, DKC AKD, BKC AHA, AHB, AHC, AHD f ≤ 50MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 f ≤ 70MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 f ≤ 50MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 f ≤ 70MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 f ≤ 50MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 f ≤ 70MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 f ≤ 70MHz, CL = 15pF f ≤ 70MHz, CL = 15pF f ≤ 70MHz, CL = 15pF 4.5 4.5 2.7 4.5 4.5 2.7 3.0 4.5 4.5 2.7 3.0 4.5 4.5 4.5 VSS − 40 − 15 − 10 − 40 − 20 − 20 − 20 − 40 − 40 − 20 − 20 − 20 − 40 − 15 − 40 − 20 − 40 − 20 typ – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – max 5.5 5.5 3.6 5.5 5.5 V 3.6 3.6 5.5 5.5 V 3.6 3.6 5.5 5.5 5.5 VDD + 85 + 75 + 70 + 85 + 80 + 80 + 80 + 85 + 85 + 80 + 80 + 80 + 85 + 75 + 85 + 80 + 85 + 80 °C °C °C °C V V V V V Unit °C °C SEIKO NPC CORPORATION —6 SM5006 series Electrical Characteristics 5006×N series 3V operation: VDD = 2.7 to 3.6 V, VSS = 0 V, Ta = −20 to 80 °C unless otherwise noted. Rating Parameter HIGH-level output voltage LOW-level output voltage Output leakage current HIGH-level input voltage LOW-level input voltage Symbol VOH VOL IZ VIH VIL Condition min Q: Measurement cct 1, VDD = 2.7V, IOH = 8mA Q: Measurement cct 2, VDD = 2.7V, IOL = 8mA Q: Measurement cct 2, INHN = LOW, VDD = 5.5V INHN INHN SM5006ANCS CF5006ANC SM5006BNCS CF5006BNC SM5006CNCS CF5006CNC SM5006ANDS CF5006AND SM5006BNES CF5006BNE SM5006CNES CF5006CNE SM5006DNES CF5006DNE SM5006CNDS CF5006CND SM5006DNCS CF5006DNC SM5006ANES CF5006ANE SM5006ANFS CF5006ANF VOH = VDD VOL = VSS 2.2 – – – 2.0 – typ 2.4 0.3 – – – – max – 0.4 10 µA 10 – 0.5 V V V V Unit f = 30MHz – 8 16 f = 30MHz, Ta = –10 to 70°C f = 50MHz INHN = open, Measurement cct 3, load cct 1, VDD = 3.0 to 3.6V, CL = 15pF – – 8 13 16 26 Current consumption IDD f = 70MHz – 15 30 mA f = 40MHz, Ta = –10 to 70°C – 11 22 f = 70MHz – 20 40 kΩ INHN pull-up resistance RUP Measurement cct 4 SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006ANCS, CF5006ANC SM5006CNCS, CF5006CNC SM5006ANDS, CF5006AND SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF SM5006CNDS, CF5006CND SM5006CNES, CF5006CNE 50 6.97 4.76 4.16 – 8.2 5.6 4.9 150 9.43 6.44 5.64 Feedback resistance Rf Measurement cct 5 kΩ 2.21 2.6 2.99 Built-in resistance RG RD Design value, determined by the Rf value Design value, determined by the Rf value Design value. A monitor pattern on a wafer is tested. Design value. A monitor pattern on a wafer is tested. 17 17 7.44 14.88 20 20 8 16 23 23 8.56 Ω Built-in capacitance CG CD pF 17.12 SEIKO NPC CORPORATION —7 SM5006 series 5V operation: VDD = 4.5 to 5.5V, VSS = 0V, Ta = −40 to 85°C unless otherwise noted. Parameter HIGH-level output voltage LOW-level output voltage Output leakage current HIGH-level input voltage LOW-level input voltage Symbol VOH VOL IZ VIH VIL Condition Q: Measurement cct 1, VDD = 4.5V, IOH = 16mA Q: Measurement cct 2, VDD = 4.5V, IOL = 16mA Q: Measurement cct 2, INHN = LOW, VDD = 5.5V INHN INHN f = 30MHz f = 40MHz INHN = open, Measurement cct 3, load cct 1, VDD = 4.5 to 5.5V, CL = 50pF f = 60MHz f = 60MHz, Ta = –20 to 80°C f = 70MHz f = 70MHz, Ta = –20 to 80°C f = 60MHz, CL = 15pF, Ta = –15 to 75°C Current consumption IDD f = 60MHz, CL = 15pF, Ta = 0 to 70°C f = 70MHz, CL = 15pF, Ta = –15 to 75°C f = 70MHz, CL = 15pF, Ta = 0 to 70°C f = 100MHz, CL = 15pF, Ta = –20 to 80°C f = 100MHz, CL = 15pF, Ta = 0 to 70°C f = 100MHz, CL = 30pF f = 100MHz, CL = 15pF f = 107MHz, CL = 30pF, Ta = –20 to 80 °C f = 107MHz, CL = 15pF, Ta = –20 to 80°C INHN pull-up resistance RUP Measurement cct 4 SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006ANCS, CF5006ANC SM5006CNCS, CF5006CNC SM5006ANDS, CF5006AND SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF SM5006CNDS, CF5006CND SM5006CNES, CF5006CNE Design value, determined by the Rf value Design value, determined by the Rf value Design value. A monitor pattern on a wafer is tested. Design value. A monitor pattern on a wafer is tested. SM5006ANAS CF5006ANA SM5006ANBS CF5006ANB CF5006ANC SM5006ANCS CF5006AND CF5006BNC SM5006ANDS SM5006BNCS CF5006CNC SM5006CNCS CF5006CND CF5006DNC SM5006CNDS SM5006DNCS CF5006CNE CF5006DNE SM5006CNES SM5006DNES CF5006ANE SM5006ANES CF5006ANF CF5006BNE SM5006ANFS SM5006BNES VOH = VDD VOL = VSS Rating min 4.0 – – – 2.0 – – – – – – – – – – – – – – – – – 50 6.97 4.76 4.16 typ 4.2 0.3 – – – – 18 20 30 30 40 40 28 28 35 35 45 45 50 45 60 50 – 8.2 5.6 4.9 max – 0.4 10 10 – 0.8 35 40 60 50 80 70 50 50 65 65 80 80 100 90 100 90 150 9.43 6.44 5.64 kΩ 2.21 2.6 2.99 kΩ Unit V V µA V V mA INHN = open, Measurement cct 3, load cct 1, VDD = 4.5 to 5.5V Feedback resistance Rf Measurement cct 5 Built-in resistance RG RD CG CD 17 17 7.44 14.88 20 20 8 16 23 23 8.56 17.12 Ω pF Built-in capacitance SEIKO NPC CORPORATION —8 SM5006 series 5006×K series VDD = 4.5 to 5.5V, VSS = 0V, Ta = −40 to 85°C unless otherwise noted. Rating Parameter Symbol Condition min SM5006AKAS, CF5006AKA SM5006AKBS, CF5006AKB SM5006AKCS, CF5006AKC SM5006CKDS, CF5006CKD SM5006DKCS, CF5006DKC SM5006AKDS, CF5006AKD SM5006BKCS, CF5006BKC LOW-level output voltage Output leakage current HIGH-level input voltage LOW-level input voltage VOL IZ VIH VIL Q: Measurement cct 2, VDD = 4.5V, IOL = 16mA Q: Measurement cct 2, INHN = LOW, VDD = 5.5V INHN INHN f = 30MHz f = 40MHz f = 60MHz, Ta = –15 to 75°C f = 60MHz, Ta = 0 to 70°C f = 70MHz, Ta = –20 to 80°C f = 70MHz, Ta = –15 to 75°C f = 70MHz, Ta = 0 to 70°C INHN pull-up resistance RUP Measurement cct 4 SM5006AKAS, CF5006AKA SM5006AKBS, CF5006AKB Feedback resistance Rf Measurement cct 5 SM5006AKCS, CF5006AKC SM5006AKDS, CF5006AKD SM5006CKDS, CF5006CKD Built-in resistance RG RD Built-in capacitance CG CD Design value, determined by the Rf value Design value, determined by the Rf value Design value. A monitor pattern on a wafer is tested. Design value. A monitor pattern on a wafer is tested. SM5006AKAS CF5006AKA SM5006AKBS CF5006AKB CF5006AKC CF5006DKC SM5006AKCS SM5006DKCS CF5006AKD CF5006BKC CF5006CKD SM5006AKDS SM5006BKCS SM5006CKDS VOH = VDD VOL = VSS typ max Unit HIGH-level output voltage VOH Q: Measurement cct 1, VDD = 4.5V, IOH = 16mA 3.9 4.2 – V 4.0 – – – 2.0 – – – – – – – 4.2 0.3 – – – – 16 18 25 25 35 35 – 0.4 10 µA 10 – 0.8 32 36 50 50 70 70 V V V Current consumption IDD INHN = open, Measurement cct 3, load cct 1, VDD = 4.5 to 5.5V, CL = 15pF mA – 50 6.97 4.76 4.16 2.21 17 17 7.44 14.88 35 – 8.2 5.6 4.9 2.6 20 20 8 16 70 150 9.43 6.44 5.64 2.99 23 23 8.56 pF 17.12 Ω kΩ kΩ SEIKO NPC CORPORATION —9 SM5006 series 5006AH series VDD = 4.5 to 5.5V, VSS = 0V, Ta = −40 to 85°C unless otherwise noted. Rating Parameter HIGH-level output voltage LOW-level output voltage Output leakage current HIGH-level input voltage LOW-level input voltage Symbol VOH VOL IZ VIH VIL Condition min Q: Measurement cct 1, VDD = 4.5V, IOH = 4mA Q: Measurement cct 2, VDD = 4.5V, IOL = 4mA Q: Measurement cct 2, INHN = LOW, VDD = 5.5V INHN INHN f = 30MHz f = 40MHz INHN = open, Measurement cct 3, load cct 1, VDD = 4.5 to 5.5V, CL = 15pF f = 60MHz, Ta = –20 to 80°C f = 60MHz, Ta = –15 to 75°C f = 70MHz, Ta = –20 to 80°C f = 70MHz, Ta = –15 to 75°C INHN pull-up resistance RUP Measurement cct 4 SM5006AHAS, CF5006AHA SM5006AHBS, CF5006AHB Feedback resistance Rf Measurement cct 5 SM5006AHCS, CF5006AHC SM5006AHDS, CF5006AHD Built-in resistance RG RD Built-in capacitance CG CD Design value, determined by the Rf value Design value, determined by the Rf value Design value. A monitor pattern on a wafer is tested. Design value. A monitor pattern on a wafer is tested. 4.16 2.21 17 17 7.44 14.88 4.9 2.6 20 20 8 16 5.64 2.99 23 23 8.56 pF 17.12 Ω SM5006AHAS CF5006AHA SM5006AHBS CF5006AHB CF5006AHC SM5006AHCS CF5006AHD SM5006AHDS VOH = VDD VOL = VSS 3.9 – – – 2.0 – – – – – – – 50 6.97 4.76 typ 4.2 0.3 – – – – 15 18 25 25 32 32 – 8.2 5.6 max – 0.5 10 µA 10 – 0.8 30 36 50 mA 50 65 65 150 9.43 6.44 kΩ kΩ V V V V Unit Current consumption IDD SEIKO NPC CORPORATION —10 SM5006 series Switching Characteristics 5006×N series 3V operation: VDD = 2.7 to 3.6V, VSS = 0V, Ta = −20 to 80°C unless otherwise noted. Parameter Symbol Measurement cct 3, load cct 1, 0.1VDD to 0.9VDD , CL = 15pF, Ta = –10 to 70°C Condition SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006CNCS, CF5006CNC SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC SM5006ANCS, CF5006ANC SM5006ANDS, CF5006AND SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF SM5006BNCS, CF5006BNC SM5006BNES, CF5006BNE SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006CNCS, CF5006CNC SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC SM5006ANCS, CF5006ANC SM5006ANDS, CF5006AND SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF SM5006BNCS, CF5006BNC SM5006BNES, CF5006BNE SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006ANCS, CF5006ANC SM5006CNCS, CF5006CNC SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC Rating min typ max Unit tr1 – 3.5 7.0 Output rise time tr2 Measurement cct 3, load cct 1, 0.1VDD to 0.9VDD , CL = 15pF ns – 3.5 7.0 tf1 Measurement cct 3, load cct 1, 0.9VDD to 0.1VDD , CL = 15pF, Ta = –10 to 70°C – 3.5 7.0 Output fall time tf2 Measurement cct 3, load cct 1, 0.9VDD to 0.1VDD , CL = 15pF ns – 3.5 7.0 Measurement cct 3, load cct 1, Ta = 25°C, VDD = 3.3V, CL = 15pF, f = 30MHz Measurement cct 3, load cct 1, Ta = 25°C, VDD = 3.3V, CL = 15pF, f = 40MHz Output duty cycle*1 Duty Measurement cct 3, load cct 1, Ta = 25°C, VDD = 3.3V, CL = 15pF, f = 50MHz Measurement cct 3, load cct 1, Ta = 25°C, VDD = 3.3V, CL = 15pF, f = 70MHz Output disable delay time Output enable delay time tPLZ tPZL 40 – 60 40 – 60 % SM5006ANDS, CF5006AND SM5006BNCS, CF5006BNC SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF SM5006BNES, CF5006BNE SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE 40 – 60 40 – 60 Measurement cct 3, load cct 1, Ta = 25°C, VDD = 5V, CL ≤ 15pF – – – – 100 100 ns ns *1. The duty cycle characteristic is checked the sample chips of each production lot. SEIKO NPC CORPORATION —11 SM5006 series 5V operation: VDD = 4.5 to 5.5V, VSS = 0V, Ta = −40 to 85°C unless otherwise noted. Parameter Symbol Condition SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006CNCS, CF5006CNC SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC SM5006ANCS, CF5006ANC SM5006ANDS, CF5006AND SM5006BNCS, CF5006BNC SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE CF5006ANE CF5006ANF CF5006BNE SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006CNCS, CF5006CNC SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC tr3 Measurement cct 3, load cct 1, 0.1VDD to 0.9VDD , CL = 50pF SM5006ANCS, CF5006ANC SM5006ANDS, CF5006AND SM5006BNCS, CF5006BNC SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF SM5006BNES, CF5006BNE SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006CNCS, CF5006CNC SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC SM5006ANCS, CF5006ANC SM5006ANDS, CF5006AND SM5006BNCS, CF5006BNC SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE CF5006ANE CF5006ANF CF5006BNE SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006CNCS, CF5006CNC SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC tf3 Measurement cct 3, load cct 1, 0.9VDD to 0.1VDD , CL = 50pF SM5006ANCS, CF5006ANC SM5006ANDS, CF5006AND SM5006BNCS, CF5006BNC SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF SM5006BNES, CF5006BNE Rating min typ max Unit – 2.0 4.0 tr1 Measurement cct 3, load cct 1, 0.1VDD to 0.9VDD , CL = 15pF – 1.5 3.0 tr2 Output rise time Measurement cct 3, load cct 1, 0.1VDD to 0.9VDD , CL = 30pF – 2.0 4.0 ns – 4.0 8.0 – 3.5 7.0 – 3.0 6.0 – 2.0 4.0 tf1 Measurement cct 3, load cct 1, 0.9VDD to 0.1VDD , CL = 15pF – 1.5 3.0 tf2 Output fall time Measurement cct 3, load cct 1, 0.9VDD to 0.1VDD , CL = 30pF – 2.0 4.0 ns – 4.0 8.0 – 3.5 7.0 – 3.0 6.0 SEIKO NPC CORPORATION —12 SM5006 series Rating min SM5006ANAS CF5006ANA SM5006ANBS CF5006ANB SM5006ANCS CF5006ANC SM5006ANDS CF5006AND SM5006BNCS CF5006BNC CF5006ANE SM5006ANES CF5006ANF CF5006BNE SM5006ANFS SM5006BNES SM5006CNCS CF5006CNC SM5006DNCS CF5006DNC SM5006CNES CF5006CNE SM5006DNES CF5006DNE SM5006CNCS CF5006CNC SM5006CNDS CF5006CND SM5006DNCS CF5006DNC 45 45 45 typ – – – max 55 55 55 Parameter Symbol Condition f = 30MHz, CL = 50pF f = 40MHz, CL = 50pF f = 60MHz, CL = 50pF f = 70MHz, CL = 50pF f = 100MHz, CL = 30pF f = 100MHz, CL = 15pF Unit 45 – 55 45 45 45 45 – – – – 55 55 55 55 Output duty cycle*1 Duty Measurement cct 3, load cct 1, Ta = 25°C, VDD = 5.0V f = 107MHz, CL = 30pF f = 107MHz, CL = 15pF f = 50MHz, CL = 50pF % 45 – 55 f = 100MHz, CL = 15pF f = 60MHz, CL = 15pF f = 70MHz, CL = 15pF Output disable delay time Output enable delay time tPLZ tPZL 45 – 55 40 – 60 40 – 60 Measurement cct 3, load cct 1, Ta = 25°C, VDD = 5V, CL ≤ 15pF – – – – 100 100 ns ns *1. The duty cycle characteristic is checked the sample chips of each production lot. SEIKO NPC CORPORATION —13 SM5006 series 5006×K series VSS = 0V, Ta = −40 to 85°C unless otherwise noted. Parameter Symbol Condition Measurement cct 3, load cct 1, 0.4V to 2.4V, VDD = 4.5 to 5.5V Measurement cct 3, load cct 1, 2.4V to 0.4V, VDD = 4.5 to 5.5V f = 30MHz f = 40MHz f = 60MHz Output duty cycle*1 Measurement cct 3, load cct 1, Ta = 25°C, VDD = 5.0V, CL = 15pF CL = 15pF CL = 50pF CL = 15pF CL = 50pF SM5006AKAS CF5006AKA SM5006AKBS CF5006AKB SM5006AKCS CF5006AKC SM5006AKDS CF5006AKD SM5006BKCS CF5006BKC SM5006DKCS CF5006DKC SM5006CKDS CF5006CKD SM5006DKCS CF5006DKC Rating min – – – – 45 45 40 typ 2 – 2 – – – – max 4 7 4 7 55 55 60 Unit Output rise time tr tf ns Output fall time ns Duty f = 70MHz 45 – 55 % f = 50MHz 45 – 55 f = 70MHz Output disable delay time Output enable delay time tPLZ tPZL 40 – 60 Measurement cct 3, load cct 1, Ta = 25°C, VDD = 5V, CL ≤ 15pF – – – – 100 100 ns ns *1. The duty cycle characteristic is checked the sample chips of each production lot. 5006AH series VDD = 4.5 to 5.5V, VSS = 0V, Ta = −40 to 85°C unless otherwise noted. Parameter Symbol tr1 tr2 tf1 tf2 Condition Measurement cct 3, load cct 1, 0.1VDD to 0.9VDD Measurement cct 3, load cct 1, 0.9VDD to 0.1VDD f = 30MHz f = 40MHz f = 50MHz Output duty cycle*1 Duty Measurement cct 3, load cct 1, Ta = 25°C, VDD = 5.0V, CL = 15pF f = 60MHz, Ta = –20 to 80°C f = 60MHz, Ta = –15 to 75°C f = 70MHz, Ta = –20 to 80°C f = 70MHz, Ta = –15 to 75°C Output disable delay time Output enable delay time tPLZ tPZL CL = 15pF CL = 50pF CL = 15pF CL = 50pF SM5006AHAS CF5006AHA SM5006AHBS CF5006AHB SM5006AHCS CF5006AHC CF5006AHC SM5006AHCS CF5006AHD SM5006AHDS Rating min – – – – 45 45 45 40 40 40 40 – – typ 5.0 13 5.0 13 – – – – – – – – – max 7.0 21 7.0 21 55 55 55 60 60 60 60 100 100 ns ns % Unit Output rise time ns Output fall time ns Measurement cct 3, load cct 1, Ta = 25°C, VDD = 5V, CL ≤ 15pF *1. The duty cycle characteristic is checked the sample chips of each production lot. SEIKO NPC CORPORATION —14 SM5006 series Current consumption and Output waveform with NPC’s standard crystal R [ Ω] 18.62 20.53 22.17 25.42 16.60 35.83 f [MHz] L [mH] 16.24 11.34 7.40 4.18 3.56 2.98 Ca [fF] 1.733 1.396 1.370 1.254 0.726 0.732 Cb [pF] 5.337 3.989 4.105 5.170 5.394 2.265 Cb 30 40 50 70 100 107 L Ca R FUNCTIONAL DESCRIPTION Standby Function When INHN goes LOW, the oscillator output on Q goes high impedance. INHN HIGH (or open) LOW Q fO output frequency High impedance Oscillator Normal operation Normal operation SEIKO NPC CORPORATION —15 SM5006 series MEASUREMENT CIRCUITS Measurement cct 1 Measurement cct 4 VDD 5.0V Q R2 Signal Generator R1 C1 XT Rfo XTN VSS VDD RUP = VSS INHN VDD IPR Q out monitor VOH 0V VIH A IPR 3.5VP−P , 10MHz sine wave input signal (5V operation) 2.0VP−P , 10MHz sine wave input signal (3V operation) C1 : 0.001µF R1 : 50Ω R2 : 250Ω (5006×N×/5V operation) 275Ω (5006×N×/3V operation) 245Ω (5006AKA, AKB, AKC, CKD, DKC) 250Ω (5006AKD, BKC) 975Ω (5006AH×) Rfo : 2.7kΩ (5006B××, D××) Measurement cct 2 Measurement cct 5 IOL, IZ VDD XT INHN VSS Q IZ XT VDD A XTN Rf = VSS VDD IRf V VOL A IRf Measurement cct 3 A XT Rfo X'tal XTN INHN VDD IDD IST Q VSS Rfo : 2.7kΩ (5006B××, D××) SEIKO NPC CORPORATION —16 SM5006 series Load cct 1 Load cct 2 Q output CL (Including probe capacitance) 400Ω Q output CL (Including probe capacitance) Switching Time Measurement Waveform Output duty level (CMOS) Q output 0.9VDD 0.1VDD TW 0.9VDD 0.1VDD DUTY measurement voltage (0.5V DD ) tr Output duty level (TTL) tf Q output 2.4V DD 0.4V DD TW 2.4V DD 0.4V DD DUTY measurement voltage (1.4V DD ) tr Output duty cycle (CMOS) tf Q output TW T DUTY measurement voltage (0.5V DD) DUTY= TW/ T 100 (%) Output duty cycle (TTL) Q output TW T DUTY measurement voltage (1.4V DD) DUTY= TW/ T 100 (%) SEIKO NPC CORPORATION —17 SM5006 series Output Enable/Disable Delay INHN VIH VIL tPLZ Q output INHN input waveform tr = tf tPZL 10ns SEIKO NPC CORPORATION —18 SM5006 series Please pay your attention to the following points at time of using the products shown in this document. The products shown in this document (hereinafter “Products”) are not intended to be used for the apparatus that exerts harmful influence on human lives due to the defects, failure or malfunction of the Products. Customers are requested to obtain prior written agreement for such use from SEIKO NPC CORPORATION (hereinafter “NPC”). Customers shall be solely responsible for, and indemnify and hold NPC free and harmless from, any and all claims, damages, losses, expenses or lawsuits, due to such use without such agreement. NPC reserves the right to change the specifications of the Products in order to improve the characteristic or reliability thereof. NPC makes no claim or warranty that the contents described in this document dose not infringe any intellectual property right or other similar right owned by third parties. Therefore, NPC shall not be responsible for such problems, even if the use is in accordance with the descriptions provided in this document. Any descriptions including applications, circuits, and the parameters of the Products in this document are for reference to use the Products, and shall not be guaranteed free from defect, inapplicability to the design for the mass-production products without further testing or modification. Customers are requested not to export or re-export, directly or indirectly, the Products to any country or any entity not in compliance with or in violation of the national export administration laws, treaties, orders and regulations. Customers are requested appropriately take steps to obtain required permissions or approvals from appropriate government agencies. SEIKO NPC CORPORATION 15-6, Nihombashi-kabutocho, Chuo-ku, Tokyo 103-0026, Japan Telephone: +81-3-6667-6601 Facsimile: +81-3-6667-6611 http://www.npc.co.jp/ Email: sales@npc.co.jp NC9713FE 2006.04 SEIKO NPC CORPORATION —19