CF5016AL2-2

CF5016 series 1.8V Operation Fundamental Frequency Crystal Oscillator Module ICs OVERVIEW The CF5016 series are 1.8V operation crystal oscillator ICs. They are available for frequencies up to 50MHz. They employ a recently developed low-voltage process optimized for operation at 1.8V, resulting in stable operation at low voltages while maintaining the same output duty stability of existing devices. They are ideally suited for battery-operated electronic equipment applications where small size, low-voltage operation, and low power dissipation are essential. FEATURES I I I I I I 1.6 to 2.0V operating supply voltage range Up to 50MHz oscillation frequency range – 40 to 85°C operating temperature range Oscillation capacitors built-in • CG = 18pF, CD = 18pF Inverter amplifier feedback resistor built-in Standby function • High impedance in standby mode, oscillator stops I I I I I Low standby current • Power-saving pull-up resistor built-in fO, fO/2, fO/4, fO/8, or fO/16 output frequency, determined by internal connection CMOS output duty level (1/2VDD) Molybdenum-gate CMOS process Chip form (CF5016AL×) SERIES CONFIGURATION Recommended operating frequency range1 [MHz] CL = 15pF CF5016AL1 CF5016AL2 CF5016AL3 CF5016AL4 CF5016AL5 4 to 50 4 to 30 18 18 CL = 30pF Built-in capacitance [pF] CG CD fO fO/2 fO/4 fO/8 fO/16 Yes Yes Yes Yes Yes Output frequency Standby function Version 1. The recommended operating frequency is a yardstick value derived from the crystal used for NPC characteristics authentication. However, the oscillator frequency band is not guaranteed. Specifically, the characteristics can vary greatly due to crystal characteristics and mounting conditions, so the oscillation characteristics of components must be carefully evaluated. ORDERING INFORMATION Device CF5016AL×–2 Package Chip form SEIKO NPC CORPORATION —1 CF5016 series PAD LAYOUT (Unit: µm) (720,680) NPC VDD Y HA 5016 Q VSS INHN (0,0) XT X XTN Chip size: 0.72 × 0.68mm Chip thickness: 220 ± 30µm PAD size: 90µm Chip base: VDD level PIN DESCRIPTION and PAD DIMENSIONS Pad dimensions [µm] Name I/O Description X INHN XT XTN VSS Q VDD I I O – O – Output state control input. High impedance when LOW (oscillator stops). Power-saving pull-up resistor built-in. Amplifier input Amplifier output Ground Output. Output frequency (fO, fO/2, fO/4, fO/8, fO/16) determined by internal connection Supply voltage Crystal connection pins. Crystal is connected between XT and XTN. 151 238 512 588 588 131 Y 277 131 131 345 548 548 BLOCK DIAGRAM VDD VSS XTN CG CD XT Rf 1/2 1/2 1/2 1/2 Q INHN INHN = LOW active SEIKO NPC CORPORATION —2 CF5016 series SPECIFICATIONS Absolute Maximum Ratings VSS = 0V Parameter Supply voltage range Input voltage range Output voltage range Operating temperature range Storage temperature range Output current Symbol VDD VIN VOUT Topr TSTG IOUT Condition Rating −0.5 to +3.6 −0.5 to VDD + 0.5 −0.5 to VDD + 0.5 −40 to +85 −65 to +150 12 Unit V V V °C °C mA Recommended Operating Conditions VSS = 0V Parameter Supply voltage range Input voltage range Operating temperature range Operating frequency range Symbol VDD VIN TOPR fOSC CL ≤ 15pF CL ≤ 30pF Condition Rating 1.6 to 2.0 VSS to VDD −40 to +85 4 to 50*1 4 to 30 Unit V V °C MHz MHz *1. When the operating frequency is over 45MHz, the duty variation tends to increase. SEIKO NPC CORPORATION —3 CF5016 series Electrical Characteristics VDD = 1.6 to 2.0V, VSS = 0V, Ta = −40 to +85°C unless otherwise noted. Rating Parameter HIGH-level output voltage LOW-level output voltage HIGH-level input voltage LOW-level input voltage Output leakage current Symbol VOH VOL VIH VIL IZ Condition min Q: Measurement cct 1, VDD = 1.6V, IOH = 2.8mA Q: Measurement cct 1, VDD = 1.6V, IOL = 2.8mA INHN INHN Q: Measurement cct 2, INHN = LOW VOH = VDD VOL = VSS CF5016AL1 CF5016AL2 Current consumption IDD Measurement cct 3, load cct 1, INHN = open, CL = 15pF, f = 50MHz CF5016AL3 CF5016AL4 CF5016AL5 Standby current INHN pull-up resistance Feedback resistance Built-in capacitance IST RUP1 RUP2 Rf CG CD Measurement cct 5 Design value. A monitor pattern on a wafer is tested. 15.3 18 20.7 pF Measurement cct 3, INHN = LOW Measurement cct 4 30 100 15.3 150 300 18 300 600 20.7 1.1 – 0.7VDD – – – – – – – – – 2 typ 1.4 0.3 – – – – 3.5 2.5 2 1.5 1 – 6 max – 0.4 – 0.3VDD 10 10 7 5 4 3 2 10 12 V V V V µA µA mA mA mA mA mA µA MΩ kΩ kΩ pF Unit SEIKO NPC CORPORATION —4 CF5016 series Switching Characteristics VDD = 1.6 to 2.0V, VSS = 0V, Ta = −40 to +85°C unless otherwise noted. Rating Parameter Symbol tr1 tr2 Output fall time tf1 tf2 Duty1 Output duty cycle1 Duty2 Duty3 Output disable delay time2 Output enable delay time2 tPLZ tPZL Measurement cct 3, load cct 1, VDD = 1.8V, Ta = 25°C Condition min Output rise time Measurement cct 3, load cct 1, 0.2VDD to 0.8VDD Measurement cct 3, load cct 1, 0.8VDD to 0.2VDD CL = 15pF CL = 30pF CL = 15pF CL = 30pF CL = 15pF f = 45MHz CL = 15pF f = 50MHz CL = 30pF f = 30MHz Measurement cct 6, load cct 1, VDD = 1.8V, Ta = 25°C, CL = 15pF – – – – 45 40 45 – – typ 2.5 4.0 2.5 4.0 – – – – – max 5.0 ns 8.0 5.0 ns 8.0 55 60 55 200 200 % % % ns ns Unit 1. The duty cycle characteristic is checked the sample chips of each production lot. 2. Oscillator stop function is built-in. When INHN goes LOW, normal output stops. When INHN goes HIGH, normal output is not resumed until after the oscillator start-up time has elapsed. Current consumption and Output waveform with NPC’s standard crystal Cb f [MHz] 30 40 50 R [Ω] 5.26 8.24 16.12 L [mH] 2.82 5.72 6.88 Ca [fF] 9.99 2.77 1.43 Cb [pF] 2.68 2.22 1.18 L Ca R FUNCTIONAL DESCRIPTION Standby Function When INHN goes LOW, the oscillator stops and the oscillator output on Q becomes high impedance. INHN HIGH (or open) LOW Q Any fO, fO/2, fO/4, fO/8 or fO/16 output frequency High impedance Oscillator Normal operation Stopped Power-saving Pull-up Resistor The INHN pull-up resistance changes in response to the input level (HIGH or LOW). When INHN goes LOW (standby state), the pull-up resistance becomes large to reduce the current consumption during standby. SEIKO NPC CORPORATION —5 CF5016 series MEASUREMENT CIRCUITS Measurement cct 1 Measurement cct 4 Signal Generator C1 XT R1 XTN INHN R3 VDD Q VSS R2 When measuring VOL XT XTN INHN VDD Q RUP1 = VDD IPR (VPR = V SS) When measuring VOH VSS V Q output VDD VOH 0V VDD VOL 0V VPR IPR RUP2 = VDD VPR IPR (VPR = 0.7VDD) A Q output 1Vp-p, 10MHz sine wave input signal C1: 0.001µF R1: 50Ω R2: 393Ω R3: 429Ω Measurement cct 5 Measurement cct 2 XT IZ XT XTN INHN VDD Q VSS IZ XTN INHN VSS VDD Q Rf = VDD IRf A A V VOH VOL IRf Measurement cct 6 Measurement cct 3 Signal Generator A XT X'tal XTN INHN VSS VDD Q IDD IST C1 XT R1 XTN INHN VDD Q VSS 1Vp-p, 10MHz sine wave input signal C1: 0.001µF R1: 50Ω Load cct 1 Q output CL (Including probe capacitance) SEIKO NPC CORPORATION —6 CF5016 series Switching Time Measurement Waveform Output duty level Q output 0.8VDD 0.2VDD TW 0.8VDD 0.2VDD DUTY measurement voltage (0.5V DD ) tr Output duty cycle tf Q output TW T DUTY measurement voltage (0.5V DD) DUTY= TW/ T 100 (%) Output Enable/Disable Delay when the device is in standby, the oscillator stops. When standby is released, the oscillator starts and stable oscillator output occurs after a short delay. INHN VIL VIH tPLZ Q output INHN input waveform tr = tf tPZL 10ns SEIKO NPC CORPORATION —7 CF5016 series Please pay your attention to the following points at time of using the products shown in this document. The products shown in this document (hereinafter “Products”) are not intended to be used for the apparatus that exerts harmful influence on human lives due to the defects, failure or malfunction of the Products. Customers are requested to obtain prior written agreement for such use from SEIKO NPC CORPORATION (hereinafter “NPC”). Customers shall be solely responsible for, and indemnify and hold NPC free and harmless from, any and all claims, damages, losses, expenses or lawsuits, due to such use without such agreement. NPC reserves the right to change the specifications of the Products in order to improve the characteristic or reliability thereof. NPC makes no claim or warranty that the contents described in this document dose not infringe any intellectual property right or other similar right owned by third parties. Therefore, NPC shall not be responsible for such problems, even if the use is in accordance with the descriptions provided in this document. Any descriptions including applications, circuits, and the parameters of the Products in this document are for reference to use the Products, and shall not be guaranteed free from defect, inapplicability to the design for the mass-production products without further testing or modification. Customers are requested not to export or re-export, directly or indirectly, the Products to any country or any entity not in compliance with or in violation of the national export administration laws, treaties, orders and regulations. Customers are requested appropriately take steps to obtain required permissions or approvals from appropriate government agencies. SEIKO NPC CORPORATION 15-6, Nihombashi-kabutocho, Chuo-ku, Tokyo 103-0026, Japan Telephone: +81-3-6667-6601 Facsimile: +81-3-6667-6611 http://www.npc.co.jp/ Email: sales@npc.co.jp NC0207BE 2006.04 SEIKO NPC CORPORATION —8