CF5020ALC

CF5020 series High-Frequency, 3rd Overtone Crystal Oscillator Module ICs OVERVIEW The CF5020 series are high-frequency, 3rd overtone crystal oscillator module ICs. They incorporate an oscillator circuit and an output buffer that operate at high frequency on a single chip. The oscillator circuit employs CMOS inverters and a built-in damping resistor RD, reducing the crystal current compared with existing devices. The damping resistor RD is fabricated using NPC’s unique high-precision thin-film resistor technology, which suppresses oscillator characteristic variations due to changes in temperature and voltage to a minimum. The CF5020 series can be utilized to construct stable, high-frequency, 3rd overtone crystal oscillators. FEATURES I I I I I I RD built-in to reduce crystal current in the oscillator circuit 2.25 to 3.6V operating supply voltage range Recommended operating frequency range (varies with version) • 2.5V operation: 60 to 155MHz • 3.0V operation: 60 to 170MHz – 40 to 85°C operating temperature range Oscillator capacitors with excellent frequency response built-in Feedback resistors with good temperature characteristics built-in I I I I I I I I Standby function • High impedance in standby mode, oscillator stops Low standby current • Power-saving pull-up resistor built-in Oscillation detector function CMOS output duty level (1/2VDD) 50 ± 5% output duty (at 1/2VDD) 30pF output load (3.3V operation) Molybdenum-gate CMOS process Chip form (CF5020AL×) APPLICATIONS I Crystal oscillator modules (3rd overtone oscillation) SERIES CONFIGURATION Recommended operating frequency range*1 [MHz] gm ratio 2.5V operation 3.0V operation CF5020ALA CF5020ALB CF5020ALC CF5020ALD 60 to 80 70 to 115 105 to 135 110 to 155 60 to 90 80 to 125 115 to 145 135 to 170 0.6 0.8 1.0 1.0 Oscillator circuit constants Built-in capacitance Feedback Damping resistance resistance CG [pF] CD [pF] Rf [kΩ] RD [Ω] 4 3 1 1 7 3 3 5 2.5 4.5 3.3 2.2 200 57 CMOS 57 57 Yes High impedance INHN input level Standby mode Oscillator stop function Output state Version *1. The recommended operating frequency is a yardstick value derived from the crystal used for NPC characteristics authentication. However, the oscillator frequency band is not guaranteed. Specifically, the characteristics can vary greatly due to crystal characteristics and mounting conditions, so the oscillation characteristics of components must be carefully evaluated. ORDERING INFORMATION Device CF5020AL×–2 Package Chip form NIPPON PRECISION CIRCUITS INC.—1 CF5020 series PAD LAYOUT (Unit: µm) (900,1050) VDD Q Y HA5020 NPC VSS INHN (0,0) XT XTN X Chip size: 0.9 × 1.05mm Chip thickness: 220µm ± 30µm PAD size: 90µm Chip base: VDD level PIN DESCRIPTION and PAD DIMENSIONS Pad dimensions [µm] Name I/O Description X INHN XT XTN VSS Q VDD I I O – O – Output state control input. High impedance when LOW (oscillator stops). Power-saving pull-up resistor built-in. Amplifier input Amplifier output (–) ground Output (+) supply voltage Crystal connection pins. Crystal is connected between XT and XTN. 144.6 347.8 560.6 755.4 755.4 151.4 Y 190.6 171 171 497.8 905.4 918.2 BLOCK DIAGRAM VDD VSS XTN CG Rf 1 Cf CD RD XT Rf 2 Q INHN INHN = LOW active NIPPON PRECISION CIRCUITS INC.—2 CF5020 series SPECIFICATIONS Absolute Maximum Ratings VSS = 0V Parameter Supply voltage range Input voltage range Output voltage range Operating temperature range Storage temperature range Output current Symbol VDD VIN VOUT Topr TSTG IOUT Condition Rating −0.5 to +7.0 −0.5 to VDD + 0.5 −0.5 to VDD + 0.5 −40 to +85 −65 to +150 25 Unit V V V °C °C mA Recommended Operating Conditions CF5020ALA, CF5020ALB 3V Operation VSS = 0V Rating Parameter Symbol Condition min CL ≤ 15pF Operating supply voltage range VDD f ≤ 125MHz CL ≤ 30pF 2.7 3.0 2.7*1 VSS −40 typ – – – – – max 3.6 3.6 3.6*1 VDD +85 V V V V °C Unit Input voltage range Operating temperature range VIN TOPR *1. The output duty cycle variability increases than other conditions. 2.5V Operation VSS = 0V Rating Parameter Symbol f ≤ 106MHz Operating supply voltage range VDD f ≤ 70MHz f ≤ 125MHz Input voltage range Operating temperature range VIN TOPR Condition min CL ≤ 15pF CL ≤ 30pF CL ≤ 15pF 2.25 2.25 2.25*1 VSS −40 typ – – – – – max 2.75 2.75 2.75*1 VDD +85 V V V V °C Unit *1. The output duty cycle variability increases than other conditions. NIPPON PRECISION CIRCUITS INC.—3 CF5020 series CF5020ALC, CF5020ALD 3V Operation VSS = 0V Rating Parameter Symbol f ≤ 170MHz f ≤ 125MHz Condition min Operating supply voltage range Input voltage range Operating temperature range VDD VIN TOPR CL ≤ 15pF CL ≤ 30pF 2.7 2.7 VSS −40 typ – – – – max 3.6 3.6 VDD +85 V V V °C Unit 2.5V Operation VSS = 0V Rating Parameter Operating supply voltage range Input voltage range Operating temperature range Symbol VDD VIN TOPR f ≤ 155MHz Condition min CL ≤ 15pF 2.25 VSS −40 typ – – – max 2.75 VDD +85 V V °C Unit NIPPON PRECISION CIRCUITS INC.—4 CF5020 series Electrical Characteristics 2.5V operation VDD = 2.25 to 2.75V, VSS = 0V, Ta = −40 to +85°C unless otherwise noted. Rating Parameter HIGH-level output voltage LOW-level output voltage HIGH-level input voltage LOW-level input voltage Output leakage current Symbol VOH VOL VIH VIL IZ Condition min Q: Measurement cct 1, VDD = 2.25V, IOH = 8mA Q: Measurement cct 2, VDD = 2.25V, IOL = 8mA INHN INHN Q: Measurement cct 2, INHN = LOW VOH = VDD VOL = VSS CL = 15pF f = 80MHz CF5020ALA CL = 30pF f = 70MHz Measurement cct 3, load cct 1, INHN = open CL = 15pF f = 106MHz CF5020ALB CL = 30pF f = 70MHz CF5020ALC CF5020ALD Standby current INHN pull-up resistance IST RUP1 RUP2 CF5020ALA AC feedback resistance Rf1 Design value. A monitor pattern on a wafer is tested. CF5020ALB CF5020ALC CF5020ALD DC feedback resistance Rf2 Measurement cct 5 CF5020ALA Oscillator amplifier output resistance RD Design value. A monitor pattern on a wafer is tested. CF5020ALB CF5020ALC CF5020ALD AC feedback capacitance Cf Design value. A monitor pattern on a wafer is tested. CF5020ALA CG Design value. A monitor pattern on a wafer is tested. CF5020ALB CF5020ALC CF5020ALD Built-in capacitance CF5020ALA CD Design value. A monitor pattern on a wafer is tested. CF5020ALB CF5020ALC CF5020ALD 5.95 2.55 2.55 4.25 7 3 3 5 8.05 3.45 3.45 5.75 pF pF pF pF Measurement cct 3, INHN = LOW Measurement cct 4 50 2.12 3.82 2.80 1.87 50 170 48.4 48.4 48.4 8.5 3.40 2.55 0.85 0.85 100 2.5 4.5 3.3 2.2 100 200 57 57 57 10 4 3 1 1 150 2.88 5.18 3.80 2.53 150 230 65.6 65.6 65.6 11.5 4.60 3.45 1.15 1.15 CL = 15pF f = 135MHz CL = 15pF f = 155MHz – – – – 2 20 25 30 – 6 50 60 70 3 12 mA mA mA µA MΩ kΩ kΩ kΩ kΩ kΩ kΩ Ω Ω Ω Ω pF pF pF pF pF – – 20 20 50 50 mA mA 1.75 – 0.7VDD – – – – typ 1.95 0.3 – – – – 15 max – 0.4 – 0.3VDD 10 10 40 V V V V µA µA mA Unit Current consumption IDD NIPPON PRECISION CIRCUITS INC.—5 CF5020 series 3V operation VDD = 2.7 to 3.6V, VSS = 0V, Ta = −40 to +85°C unless otherwise noted. Rating Parameter HIGH-level output voltage LOW-level output voltage HIGH-level input voltage LOW-level input voltage Output leakage current Symbol VOH VOL VIH VIL IZ Condition min Q: Measurement cct 1, VDD = 2.7V, IOH = 8mA Q: Measurement cct 2, VDD = 2.7V, IOL = 8mA INHN INHN Q: Measurement cct 2, INHN = LOW VOH = VDD VOL = VSS CL = 15pF f = 90MHz CF5020ALA CL = 30pF f = 90MHz CL = 15pF f = 125MHz Current consumption IDD Measurement cct 3, load cct 1, INHN = open CF5020ALB CL = 30pF f = 125MHz CL = 15pF f = 135MHz CF5020ALC CL = 30pF f = 125MHz CF5020ALD Standby current INHN pull-up resistance IST RUP1 RUP2 CF5020ALA AC feedback resistance Rf1 Design value. A monitor pattern on a wafer is tested. CF5020ALB CF5020ALC CF5020ALD DC feedback resistance Rf2 Measurement cct 5 CF5020ALA Oscillator amplifier output resistance RD Design value. A monitor pattern on a wafer is tested. CF5020ALB CF5020ALC CF5020ALD AC feedback capacitance Cf Design value. A monitor pattern on a wafer is tested. CF5020ALA CG Design value. A monitor pattern on a wafer is tested. CF5020ALB CF5020ALC CF5020ALD Built-in capacitance CF5020ALA CD Design value. A monitor pattern on a wafer is tested. CF5020ALB CF5020ALC CF5020ALD 5.95 2.55 2.55 4.25 7 3 3 5 8.05 3.45 3.45 5.75 pF pF pF pF Measurement cct 3, INHN = LOW Measurement cct 4 50 2.12 3.82 2.80 1.87 50 170 48.4 48.4 48.4 8.5 3.40 2.55 0.85 0.85 100 2.5 4.5 3.3 2.2 100 200 57 57 57 10 4 3 1 1 150 2.88 5.18 3.80 2.53 150 230 65.6 65.6 65.6 11.5 4.60 3.45 1.15 1.15 CL = 15pF f = 170MHz – – – 2 40 40 – 4 100 100 5 8 mA mA µA MΩ kΩ kΩ kΩ kΩ kΩ kΩ Ω Ω Ω Ω pF pF pF pF pF – – 40 30 100 70 mA mA – – 25 25 60 60 mA mA 2.2 – 0.7VDD – – – – typ 2.4 0.3 – – – – 20 max – 0.4 – 0.3VDD 10 10 50 V V V V µA µA mA Unit NIPPON PRECISION CIRCUITS INC.—6 CF5020 series Switching Characteristics CF5020ALA, CF5020ALB 2.5V operation VDD = 2.25 to 2.75V, VSS = 0V, Ta = −40 to +85°C unless otherwise noted. Rating Parameter Symbol tr1 tr2 Output fall time tf1 tf2 Duty1 Duty2 Output disable delay time*2 Output enable delay time*2 tPLZ tPZL Condition min Output rise time Measurement cct 3, load cct 1, 0.1VDD to 0.9VDD Measurement cct 3, load cct 1, 0.9VDD to 0.1VDD CL = 15pF CL = 30pF CL = 15pF CL = 30pF CL = 15pF, f = 106MHz Measurement cct 3, load cct 1, VDD = 2.5V, Ta = 25°C CL = 15pF, f = 125MHz CL = 30pF, f = 70MHz Measurement cct 6, load cct 1, VDD = 2.5V, Ta = 25°C, CL = 15pF – – – – 45 40 45 – – typ 1 2 1 2 – – – – – max 3 5.5 3 5.5 55 60 55 100 100 ns ns ns ns % % % ns ns Unit Output duty cycle*1 *1. The duty cycle characteristic is checked the sample chips of each production lot. *2. Oscillator stop function is built-in. When INHN goes LOW, normal output stops. When INHN goes HIGH, normal output is not resumed until after the oscillator start-up time has elapsed. 3V operation VDD = 2.7 to 3.6V, VSS = 0V, Ta = −40 to +85°C unless otherwise noted. Rating Parameter Symbol tr1 Output rise time tr2 tf1 Output fall time tf2 Output duty cycle*1 Output disable delay time*2 Output enable delay time*2 Duty2 tPLZ tPZL Condition min Measurement cct 3, load cct 1, 0.1VDD to 0.9VDD CL = 15pF VDD = 3.0 to 3.6V CL = 30pF CL = 15pF VDD = 3.0 to 3.6V CL = 30pF – – – – 45 – – typ 1 1.5 1 1.5 – – – max 2.5 3 2.5 3 55 100 100 ns ns ns ns % ns ns Unit Measurement cct 3, load cct 1, 0.9VDD to 0.1VDD Measurement cct 3, load cct 1, VDD = 3.0V, Ta = 25°C, CL = 30pF, f = 125MHz Measurement cct 6, load cct 1, VDD = 3.0V, Ta = 25°C, CL = 15pF *1. The duty cycle characteristic is checked the sample chips of each production lot. *2. Oscillator stop function is built-in. When INHN goes LOW, normal output stops. When INHN goes HIGH, normal output is not resumed until after the oscillator start-up time has elapsed. NIPPON PRECISION CIRCUITS INC.—7 CF5020 series CF5020ALC, CF5020ALD 2.5V operation VDD = 2.25 to 2.75V, VSS = 0V, Ta = −40 to +85°C unless otherwise noted. Rating Parameter Output rise time Output fall time Output duty cycle*1 Output disable delay time*2 Output enable delay time*2 Symbol tr1 tf1 Duty1 tPLZ tPZL Condition min Measurement cct 3, load cct 1, 0.1VDD to 0.9VDD, CL = 15pF Measurement cct 3, load cct 1, 0.9VDD to 0.1VDD, CL = 15pF Measurement cct 3, load cct 1, VDD = 2.5V, Ta = 25°C, CL = 15pF, f = 155MHz Measurement cct 6, load cct 1, VDD = 2.5V, Ta = 25°C, CL = 15pF – – 45 – – typ 1 1 – – – max 3 3 55 100 100 ns ns % ns ns Unit *1. The duty cycle characteristic is checked the sample chips of each production lot. *2. Oscillator stop function is built-in. When INHN goes LOW, normal output stops. When INHN goes HIGH, normal output is not resumed until after the oscillator start-up time has elapsed. 3V operation VDD = 2.7 to 3.6V, VSS = 0V, Ta = −40 to +85°C unless otherwise noted. Rating Parameter Symbol tr1 tr2 Output fall time tf1 tf2 Output duty cycle*1 Output disable delay time*2 Output enable delay time*2 Duty1 Duty2 tPLZ tPZL Condition min Output rise time Measurement cct 3, load cct 1, 0.1VDD to 0.9VDD Measurement cct 3, load cct 1, 0.9VDD to 0.1VDD Measurement cct 3, load cct 1, VDD = 3.0V, Ta = 25°C CL = 15pF CL = 30pF CL = 15pF CL = 30pF CL = 15pF, f = 170MHz CL = 30pF, f = 125MHz – – – – 45 45 – – typ 1 1.5 1 1.5 – – – – max 2.5 4 2.5 4 55 55 100 100 ns ns ns ns % % ns ns Unit Measurement cct 6, load cct 1, VDD = 3.0V, Ta = 25°C, CL = 15pF *1. The duty cycle characteristic is checked the sample chips of each production lot. *2. Oscillator stop function is built-in. When INHN goes LOW, normal output stops. When INHN goes HIGH, normal output is not resumed until after the oscillator start-up time has elapsed. NIPPON PRECISION CIRCUITS INC.—8 CF5020 series FUNCTIONAL DESCRIPTION Standby Function When INHN goes LOW, the oscillator stops and the oscillator output on Q becomes high impedance. INHN HIGH (or open) LOW Q fO output frequency High impedance Oscillator Normal operation Stopped Power-saving Pull-up Resistor The INHN pull-up resistance changes in response to the input level (HIGH or LOW). When INHN goes LOW (standby state), the pull-up resistance becomes large to reduce the current consumption during standby. NIPPON PRECISION CIRCUITS INC.—9 CF5020 series MEASUREMENT CIRCUITS Measurement cct 1 Measurement cct 4 Signal Generator C1 XT R1 XTN INHN VDD Q VSS R2 XT XTN INHN VDD Q VSS RUP1 = VDD IPR (VPR = V SS) V VPR VDD VOH 0V IPR RUP2 = VDD VPR IPR (VPR = 0.7VDD) A Q output 2Vp-p, 10MHz sine wave input signal C1: 0.001µF R1: 50Ω R2: 219Ω (2.5V operation) 275Ω (3.0V operation) Measurement cct 5 Measurement cct 2 XT IZ, IOL XT XTN INHN VDD Q VSS IZ XTN INHN VSS VDD Q Rf = VDD IRf A A V VOH VOL IRf Measurement cct 6 Measurement cct 3 Signal Generator A XT X'tal XTN INHN VSS VDD Q IDD IST C1 XT R1 XTN INHN VDD Q VSS 2Vp-p, 10MHz sine wave input signal C1: 0.001µF R1: 50Ω Load cct 1 Q output CL (Including probe capacitance) NIPPON PRECISION CIRCUITS INC.—10 CF5020 series Switching Time Measurement Waveform Output duty level, tr, tf Q output 0.9VDD 0.1VDD TW 0.9VDD 0.1VDD DUTY measurement voltage (0.5V DD ) tr Output duty cycle tf Q output TW T DUTY measurement voltage (0.5V DD) DUTY= TW/ T 100 (%) Output Enable/Disable Delay when the device is in standby, the oscillator stops. When standby is released, the oscillator starts and stable oscillator output occurs after a short delay. INHN VIL VIH tPLZ Q output INHN input waveform tr = tf tPZL 10ns NIPPON PRECISION CIRCUITS INC.—11 CF5020 series Please pay your attention to the following points at time of using the products shown in this document. The products shown in this document (hereinafter “Products”) are not intended to be used for the apparatus that exerts harmful influence on human lives due to the defects, failure or malfunction of the Products. Customers are requested to obtain prior written agreement for such use from NIPPON PRECISION CIRCUITS INC. (hereinafter “NPC”). Customers shall be solely responsible for, and indemnify and hold NPC free and harmless from, any and all claims, damages, losses, expenses or lawsuits, due to such use without such agreement. NPC reserves the right to change the specifications of the Products in order to improve the characteristic or reliability thereof. NPC makes no claim or warranty that the contents described in this document dose not infringe any intellectual property right or other similar right owned by third parties. Therefore, NPC shall not be responsible for such problems, even if the use is in accordance with the descriptions provided in this document. Any descriptions including applications, circuits, and the parameters of the Products in this document are for reference to use the Products, and shall not be guaranteed free from defect, inapplicability to the design for the mass-production products without further testing or modification. Customers are requested not to export or re-export, directly or indirectly, the Products to any country or any entity not in compliance with or in violation of the national export administration laws, treaties, orders and regulations. Customers are requested appropriately take steps to obtain required permissions or approvals from appropriate government agencies. NIPPON PRECISION CIRCUITS INC. 4-3, Fukuzumi 2-chome, Koto-ku, Tokyo 135-8430, Japan Telephone: +81-3-3642-6661 Facsimile: +81-3-3642-6698 http://www.npc.co.jp/ Email: sales@npc.co.jp NC0305CE 2004.11 NIPPON PRECISION CIRCUITS INC.—12