54ACTQ574DMQB

MICROCIRCUIT DATA SHEET MN54ACTQ574-X REV 2A0 Original Creation Date: 07/16/96 Last Update Date: 05/25/99 Last Major Revision Date: 03/12/99 Octal D Flip-Flop with TRI-STATE Outputs General Description The ACTQ574 is a high-speed, low-power octal D-type flip-flop with a buffered Common Clock (CP) and a buffered common Output Enable(OE). The information presented to the D inputs is stored in the flip-flops on the LOW-to-HIGH clock (CP) transition. The ACTQ574 utilizes Quiet Series technology to guarantee quiet output switching and improve dynamic threshold performance. FACT Quiet Series TM features G TO TM output control and undershoot corrector in addition to a split ground bus for superior performance. The ACTQ574 is functionally identical to the ACTQ374 but with different pin-out. Industry Part Number 54ACTQ574 NS Part Numbers 54ACTQ574DMQB 54ACTQ574FMQB 54ACTQ574LMQB Prime Die D574 Processing MIL-STD-883, Method 5004 Subgrp Description 1 2 3 4 5 6 7 8A 8B 9 10 11 Static tests at Static tests at Static tests at Dynamic tests at Dynamic tests at Dynamic tests at Functional tests at Functional tests at Functional tests at Switching tests at Switching tests at Switching tests at Temp ( oC) +25 C +125 C -55 C +25 C +125 C -55 C +25 C +125 C -55 C +25 C +125 C -55 C Quality Conformance Inspection MIL-STD-883 5005 1 MN54ACTQ574-X REV 2A0 MICROCIRCUIT DATA SHEET Features Icc and Ioz reduced by 50% Guaranteed simultaneous switching noise level and dynamic threshold performance Guaranteed pin-to-pin skew AC performance Inputs and outputs on opposite sides of the package allowing easy interface with microprocessors. Functionally identical to the ACQ/ACTQ374 TRI-STATE outputs drive bus lines or buffer memory address registers Outputs source/sink 24 mA 4 kV minimum ESD immunity 2 MN54ACTQ574-X REV 2A0 MICROCIRCUIT DATA SHEET (Absolute Maximum Ratings) (Note 1) Supply Voltage (Vcc) -0.5V to +7.0V DC Input Vi = Vi = DC Input Diode Current (Iik) -0.5V Vcc +0.5V Voltage (Vi) -20 mA +20 mA -0.5V to Vcc +0.5V DC Output Diode Current (Iok) Vo = -0.5V Vo = Vcc +0.5V DC Output Voltage (Vo) DC Output Source or Sink Current (Io) +50 mA DC Vcc or Ground Current per Output Pin (Icc or Ignd) +50 mA Storage Temperature (Tstg) -65 C to + 150 C DC Latch-Up Source or Sink Current +300 mA Junction Temperature (Tj) CDIP Note 1: 175 C -20 mA +20 mA -0.5 to Vcc +0.5V Absolute maximum ratings are those values beyond which damage to the device may occur. The databook specifications should be met, without exception, to ensure that the system design is reliable over its power supply, temperature, and output/input loading variables. National does not recommend operation of FACT TM circuits outside databook specifications. Recommended Operating Conditions (Note 1) Supply Voltage (Vcc) 4.5V to 5.5V Input Voltage (Vi) 0V to Vcc Output Voltage (Vo) 0V to Vcc Operating Temperature (Ta) -55 C to + 125 C Minimum Input Edge Rate (Delta V/Delta t) ACTQ Devices Vin from 0.8V to 2.0V Vcc @ 4.5V, 5.5V Note 1: 125 mV/ns All commercial packaging is not recommended for applications requiring greater than 2000 temperature cycles from -40C to +125C. 3 MN54ACTQ574-X REV 2A0 MICROCIRCUIT DATA SHEET Electrical Characteristics DC PARAMETERS (The following conditions apply to all the following parameters, unless otherwise specified.) DC: VCC 4.5V to 5.5V, Temp. Range: -55C to 125C. NOTE: -55C TEMPERATURE, SUBGROUP 3 IS GUARANTEED BUT NOT TESTED. SYMBOL IIH PARAMETER High Level input Current Low Level input Current Low level output voltage CONDITIONS VCC=5.5V, VM=5.5V NOTES PINNAME MIN MAX 0.1 1.0 -0.1 -1.0 .36 .50 .10 .36 .50 .10 1.65 3.86 3.70 4.40 4.86 4.70 5.40 3.85 4.0 80 4.0 80 4.0 80 1.0 1.6 UNIT uA uA uA uA V V V V V V V V V V V V V V uA uA uA uA uA uA mA mA SUBGROUPS 1 2, 3 1 2, 3 1 2, 3 1, 2, 3 1 2, 3 1, 2, 3 1, 2, 3 1 2, 3 1, 2, 3 1 2, 3 1, 2, 3 1, 2, 3 1 2, 3 1 2, 3 1 2, 3 1 2, 3 1, 2 INPUT 1, 2 INPUT IIL VCC=5.5V, VM=0.0V 1, 2 INPUT 1, 2 INPUT VOL VCC=4.5V, VIL=0.8V, IOL=24.0mA, VIH=2.0V VCC=4.5V, VIL=0.8V, IOL=50.0uA, VIH=2.0V VCC=5.5V, VIL=0.8V, IOL=24.0mA, VIH=2.0V VCC=5.5V, VIL=0.8V, IOL=50.0uA, VIH=2.0V 1, 2 OUTPUT 1, 2 OUTPUT 1, 2 OUTPUT 1, 2 OUTPUT 1, 2 OUTPUT 1, 2 OUTPUT 1, OUTPUT 2, 5 1, 2 OUTPUT 1, 2 OUTPUT VIOL VOH Dynamic Output current LOW High Level Output Voltage VCC=5.5V, VIH=5.5V, VIL=0.0V, IOL=50.0mA VCC=4.5V, VIL=0.8V, IOH=-24.0mA, VIH=2.0V VCC=4.5V, VIL=0.8V, IOH=-50.0uA, VIH=2.0V VCC=5.5V, VIL=0.8V, IOH=-24.0mA, VIH=2.0V VCC=5.5V, VIL=0.8V, IOH=-50.0uA, VIH=2.0V 1, 2 OUTPUT 1, 2 OUTPUT 1, 2 OUTPUT 1, 2 OUTPUT 1, OUTPUT 2, 5 1, 2 VCC 1, 2 VCC VIOH ICCH Dynamic Output current HIGH Supply Current VCC=5.5V, VIH=5.5V, VIL=0.0V, IOH=-50.0mA VCC=5.5V ICCZ Supply Current VCC=5.5V 1, 2 VCC 1, 2 VCC ICCL Supply Current VCC=5.5V 1, 2 VCC 1, 2 VCC ICCT Supply Current VCC=5.5V, VIHT=VCC-2.1V 1, 2 VCC 1, 2 VCC 4 MN54ACTQ574-X REV 2A0 MICROCIRCUIT DATA SHEET Electrical Characteristics DC PARAMETERS(Continued) (The following conditions apply to all the following parameters, unless otherwise specified.) DC: VCC 4.5V to 5.5V, Temp. Range: -55C to 125C. NOTE: -55C TEMPERATURE, SUBGROUP 3 IS GUARANTEED BUT NOT TESTED. SYMBOL IOZH PARAMETER Maximum TRI-STATE Leakage current CONDITIONS VCC=4.5V, VM=4.5V, VIH=2.0V NOTES PINNAME MIN MAX 0.25 5.0 0.25 5.0 -0.25 -5.0 -0.25 -5.0 -1.2 5.7 0.8 UNIT uA uA uA uA uA uA uA uA V V V SUBGROUPS 1 2, 3 1 2, 3 1 2, 3 1 2, 3 1, 2, 3 1, 2, 3 4 1, 2 OUTPUT 1, 2 OUTPUT VCC=5.5V, VM=5.5V, VIH=2.0V 1, 2 OUTPUT 1, 2 OUTPUT IOZL Maximum TRI-STATE Leakage current VCC=4.5V, VM=0.0V, VIH=2.0V 1, 2 OUTPUT 1, 2 OUTPUT VCC=5.5V, VM=0.0V, VIH=2.0V 1, 2 OUTPUT 1, 2 OUTPUT VIKL VIKH VILD Maximum Low Level Dynamic Input Voltage Minimum High Level Dynamic Input Voltage Quiet Output Maximum Dynamic Vol Quiet Output Minimum Dynamic Vol VCC=4.5V, IKL=-18mA VCC=4.5V, IKH=18mA VCC=5.0V, LOAD 50pF / 500 OHMS 1, 2 INPUT 1, 2 INPUT 6, 9 INPUT VIHD VCC=5.0V, LOAD 50pF / 500 OHMS 6, 9 INPUT 2.2 V 4 VOLP VCC=5.0V, LOAD 50pF / 500 OHMS 6, 8 OUTPUT 1.5 V 4 VOLV VCC=5.0V, LOAD 50pF / 500 OHMS 6, 8 OUTPUT -1.2 V 4 5 MN54ACTQ574-X REV 2A0 MICROCIRCUIT DATA SHEET Electrical Characteristics AC PARAMETERS (The following conditions apply to all the following parameters, unless otherwise specified.) AC: CL=50pf, RL=500 OHMS, TR/TF=3.0ns, Temp range: -55C to +125C. NOTE: -55C TEMPERATURE, SUBGROUP 11 IS GUARANTEED BUT NOT TESTED. SYMBOL tpLH PARAMETER Propagation Delay VCC=4.5V CONDITIONS NOTES PINNAME MIN 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 3.5 2.0 5.0 95 MAX 9.5 11.0 9.5 11.0 9.5 11.0 9.5 11.0 8.5 10.0 8.5 10.0 UNIT ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns MHz SUBGROUPS 9 10, 11 9 10, 11 9 10, 11 9 10, 11 9 10, 11 9 10, 11 9, 10, 11 9, 10, 11 9, 10, 11 9, 10, 11 3, CP to 4, 7 On 3, CP to 4, 7 On tpHL Propagation Delay VCC=4.5V 3, CP to 4, 7 On 3, CP to 4, 7 On tpZH Output Enable Time VCC=4.5V 3, OE to 4, 7 On 3, OE to 4, 7 On tpZL Output Enable Time VCC=4.5V 3, OE to 4, 7 On 3, OE to 4, 7 On tpHZ Output Disable Time VCC=4.5V 3, OE to 4, 7 On 3, OE to 4, 7 On tpLZ Output Disable Time VCC=4.5V 3, OE to 4, 7 On 3, OE to 4, 7 On ts(H/L) th(H/L) tw(H/L) fMAX Setup Time HIGH or LOW Hold Time HIGH or LOW Pulse Width Maximum Clock Frequency Note 1: Note 2: Note 3: Note 4: Note 5: Note 6: Note 7: VCC=4.5V VCC=4.5V VCC=4.5V VCC=4.5V 6 6 6 6 Dn to CP Dn to CP CP CP SCREEN TESTED 100% ON EACH DEVICE AT +25C & +125C TEMPERATURE, SUBGROUPS 1, 2, 7, & 8. SAMPLE TESTED (METHOD 5005, TABLE 1) ON EACH MFG. LOT AT +25C & +125C TEMPERATURE, SUBGROUPS A1, 2, 7, & 8. SCREEN TESTED 100% ON EACH DEVICE AT +25C TEMPERATURE ONLY SUBGROUP A9. SAMPLE TESTED (METHOD 5005, TABLE 1) ON EACH MFG. LOT AT +25C & +125C TEMPERATURE, SUBGROUPS A9 & 10. TRANSMISSION LINE DRIVING TEST, GUARDBANDED LIMITS SET FOR +25C, 2 MSEC DURATION MAX. GUARANTEED BUT NOT TESTED. (DESIGN CHARACTERIZATION DATA) +25C & +125C MIN LIMITS GUARANTEED FOR 5.5V BY GUARDBANDING 4.5V MIN. LIMITS. 6 MN54ACTQ574-X REV 2A0 MICROCIRCUIT DATA SHEET (Continued) Note 8: Note 9: MAX NUMBER OF OUTPUTS DEFINED AS (N). DATA INPUTS ARE DRIVEN 0V TO 3V. ONE OUTPUT @ VOL. MAX NUMBER OF DATA INPUTS (N) SWITCHING. (N-1) INPUTS SWITCHING 0V TO 3V. INPUT-UNDER-TEST SWITCHING 3V TO THRESHOLD (VILD), 0V TO THRESHOLD (VIHD), FREQ= 1 MHZ. 7 MN54ACTQ574-X REV 2A0 MICROCIRCUIT DATA SHEET Revision History Rev 2A0 ECN # Rel Date Originator Linda Collins Changes Removed the reference to SMD 5962-8960102 from the Features section. Changed the test condition from VIHT=VCC-2.0V to VIHT=VCC-2.1V for ICCT. Changed the test conditions from VM=4.5V to VM=0.0V and VM=5.5V to VM=0.0V for IOZL. M0003315 05/25/99 8