ADC08131CIWM

ADC08131/ADC08134/ADC08138 8-Bit High-Speed Serial I/O A/D Converters with Multiplexer Options, Voltage Reference, and Track/Hold Function June 1999 ADC08131/ADC08134/ADC08138 8-Bit High-Speed Serial I/O A/D Converters with Multiplexer Options, Voltage Reference, and Track/Hold Function General Description The ADC08131/ADC08134/ADC08138 are 8-bit successive approximation A/D converters with serial I/O and configurable input multiplexers with up to 8 channels. The serial I/O is configured to comply with the NSC MICROWIRE™ serial data exchange standard for easy interface to the COPS™ family of controllers, and can easily interface with standard shift registers or microprocessors. All three devices provide a 2.5V band-gap derived reference with guaranteed performance over temperature. A track/hold function allows the analog voltage at the positive input to vary during the actual A/D conversion. The analog inputs can be configured to operate in various combinations of single-ended, differential, or pseudo-differential modes. In addition, input voltage spans as small as 1V can be accommodated. Applications n n n n Digitizing automotive sensors Process control/monitoring Remote sensing in noisy environments Embedded diagnostics Features n Serial digital data link requires few I/O pins n Analog input track/hold function n 4- or 8-channel input multiplexer options with address logic n On-chip 2.5V band-gap reference ( ± 2% over temperature guaranteed) n No zero or full scale adjustment required n TTL/CMOS input/output compatible n 0V to 5V analog input range with single 5V power supply Key Specifications n n n n n n n n Resolution 8 Bits Conversion time (fC = 1 MHz) 8 µs (Max) Power dissipation 20 mW (Max) Single supply 5 VDC ( ± 5%) ± 1⁄2 LSB and ± 1 LSB Total unadjusted error ± 1⁄2 LSB Linearity Error (VREF = 2.5V) No missing codes (over temperature) On-board Reference +2.5V ± 1.5% (Max) Ordering Information Industrial (−40˚C ≤ TA ≤ +85˚C) ADC08131CIWM ADC08134CIWM ADC08138CIWM M14B M14B M20B Package TRI-STATE ® is a registered trademark of National Semiconductor Corporation. COPS™ microcontrollers and MICROWIRE™ are trademarks of National Semiconductor Corporation. © 1999 National Semiconductor Corporation DS010749 www.national.com Connection Diagrams ADC08138CIWM Small Outline Packages DS010749-2 ADC08134CIWM Small Outline Packages DS010749-3 ADC08131CIWM Small Outline Package DS010749-4 www.national.com 2 Absolute Maximum Ratings (Notes 1, 3) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (VCC) Voltage at Inputs and Outputs Input Current at Any Pin (Note 4) Package Input Current (Note 4) Power Dissipation at TA = 25˚C (Note 5) ESD Susceptibility (Note 6) 6.5V −0.3V to VCC + 0.3V ± 5 mA ± 20 mA 800 mW 1500V Soldering Information N Package (10 sec.) SO Package: Vapor Phase (60 sec.) Infrared (15 sec.) (Note 7) Storage Temperature 260˚C 215˚C 220˚C −65˚C to +150˚C (Notes 2, 3) TMIN ≤ TA ≤ TMAX −40˚C ≤ TA ≤ +85˚C 4.5 VDC to 6.3 VDC Operating Ratings Temperature Range Supply Voltage (VCC) Electrical Characteristics The following specifications apply for VCC = +5 VDC, VREF = +2.5 VDC and fCLK = 1 MHz unless otherwise specified. Boldface limits apply for TA = TJ = TMIN to TMAX; all other limits TA = TJ = 25˚C. Symbol Parameter Conditions Typical (Note 8) Limits (Note 9) Units (Limits) LSB (max) LSB (max) LSB (max) LSB (max) Bits (min) kΩ 1.3 6.0 VIN Analog Input Voltage DC Common-Mode Error Power Supply Sensitivity (Note 12) VREF = 2.5 VDC VCC = +5V ± 5%, VREF = +2.5 VDC On Channel = 5V, Off Channel = 0V On Channel = 0V, Off Channel = 5V On Channel = 5V, Off Channel = 0V On Channel = 0V, Off Channel = 5V VCC = 5.25V VCC = 4.75V VIN = 5.0V VIN = 0V VCC = 4.75V: IOUT = −360 µA IOUT = −10 µA VCC = 4.75V IOUT = 1.6 mA VOUT = 0V VOUT = 5V VOUT = 0V (VCC + 0.05) (GND − 0.05) kΩ (min) kΩ (max) V (max) V (min) LSB (max) LSB (max) µA (max) µA (max) µA (max) µA (max) CONVERTER AND MULTIPLEXER CHARACTERISTICS Linearity Error VREF = +2.5 VDC Full Scale Error VREF = +2.5 VDC Zero Error VREF = +2.5 VDC Total Unadjusted Error Differential Linearity RREF Reference Input Resistance VREF = +5 VDC (Note 10) VREF = +2.5 VDC 3.5 (Note 11) ±1 ±1 ±1 ±1 8 ± 1⁄2 ± 1⁄4 0.2 1 −0.2 −1 −0.2 −1 0.2 1 2.0 0.8 1 −1 2.4 4.5 0.4 −3.0 3.0 −6.5 On Channel Leakage Current (Note 13) Off Channel Leakage Current (Note 13) DIGITAL AND DC CHARACTERISTICS VIN(1) VIN(0) IIN(1) IIN(0) VOUT(1) Logical “1” Input Voltage Logical “0” Input Voltage Logical “1” Input Current Logical “0” Input Current Logical “1” Output Voltage V (min) V (max) µA (max) µA (max) V (min) V (min) V (max) µA (max) µA (max) mA (min) VOUT(0) IOUT ISOURCE Logical “0” Output Voltage TRI-STATE ® Output Current Output Source Current 3 www.national.com Electrical Characteristics (Continued) The following specifications apply for VCC = +5 VDC, VREF = +2.5 VDC and fCLK = 1 MHz unless otherwise specified. Boldface limits apply for TA = TJ = TMIN to TMAX; all other limits TA = TJ = 25˚C. Symbol Parameter Conditions Typical (Note 8) Limits (Note 9) 8.0 3.0 6.0 Units (Limits) mA (min) mA (max) mA (max) DIGITAL AND DC CHARACTERISTICS ISINK ICC Output Sink Current Supply Current ADC08134, ADC08138 ADC08131 (Note 16) CS = HIGH VOUT = VCC Electrical Characteristics The following specifications apply for VCC = +5 VDC, and fCLK = 1 MHz unless otherwise specified. Boldface limits apply for TA = TJ = TMIN to TMAX; all other limits TA = TJ = 25˚C. Symbol Parameter Conditions Typical (Note 8) 2.5 Limits (Note 9) Units (Limits) REFERENCE CHARACTERISTICS VREFOUT ∆VREF/∆T Output Voltage Temperature Coefficient Sourcing (0 ≤ IL ≤ +4 mA) ADC08134, ADC08138 Sourcing (0 ≤ IL ≤ +2 mA) ADC08131 Sinking (−1 ≤ IL ≤ 0 mA) ADC08134, ADC08138 Sinking (−1 ≤ IL ≤ 0 mA) ADC08131 Line Regulation 4.75V ≤ VCC ≤ 5.25V VREF = 0V ADC08134, ISC Short Circuit Current ADC08138 VREF = 0V ADC08131 VCC: 0V → 5V CL = 100 µF DC08134, ADC08138 ± 2% 40 2.5 ± 1.5% V ppm/˚C 0.003 0.1 0.003 0.1 %/mA (max) ∆VREF/∆IL Load Regulation (Note 17) 0.2 0.5 0.2 0.5 8 0.5 6 25 mV (max) mA (max) 8 20 200 25 ms ppm/1 kHr TSU ∆VREF/∆t Start-Up Time Long Term Stability Electrical Characteristics The following specifications apply for VCC = +5 VDC, VREF = +2.5 VDC and tr = tf = 20 ns unless otherwise specified. Boldface limits apply for TA = TJ = TMIN to TMAX; all other limits TA = TJ = 25˚C. Symbol fCLK Parameter Clock Frequency Clock Duty Cycle (Note 14) Conditions Typical (Note 8) 10 1 40 60 Limits (Note 9) Units (Limits) kHz (min) MHz (max) % (min) % (max) www.national.com 4 Electrical Characteristics (Continued) The following specifications apply for VCC = +5 VDC, VREF = +2.5 VDC and tr = tf = 20 ns unless otherwise specified. Boldface limits apply for TA = TJ = TMIN to TMAX; all other limits TA = TJ = 25˚C. Symbol TC tCA tSELECT tSET-UP tHOLD Parameter Conversion Time (Not Including MUX Addressing Time) Acquisition Time CLK High while CS is High CS Falling Edge or Data Input Valid to CLK Rising Edge Data Input Valid after CLK Rising Edge CLK Falling Edge to Output Data Valid (Note 15) TRI-STATE Delay from Rising Edge of CS to Data Output and SARS Hi-Z Capacitance of Logic Inputs Capacitance of Logic Outputs CL = 100 pF: Data MSB First Data LSB First CL = 10 pF, RL = 10 kΩ (see TRI-STATE Test Circuits) CL = 100 pF, RL = 2 kΩ 250 200 50 180 5 5 ns (max) ns (max) ns ns (max) pF pF 50 25 20 Conditions fCLK = 1 MHz Typical (Note 8) Limits (Note 9) 8 8 12 Units (Limits) 1/fCLK (max) µs (max) 1/fCLK (max) ns ns (min) ns (min) ⁄ tpd1, tpd0 t1H, t0H CIN COUT Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Note 2: Operating Ratings indicate conditions for which the device is functional. These ratings do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. Note 3: All voltages are measured with respect to AGND = DGND = 0 VDC, unless otherwise specified. Note 4: When the input voltage (VIN) at any pin exceeds the power supplies (VIN < (AGND or DGND) or VIN > AVCC) the current at that pin should be limited to 5 mA. The 20 mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of 5 mA to four pins. Note 5: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, θJA and the ambient temperature, TA. The maximum allowable power dissipation at any temperature is PD = (TJMAX − TA)/θJA or the number given in the Absolute Maximum Ratings, whichever is lower. For these devices TJMAX = 125˚C. The typical thermal resistances (θJA) of these parts when board mounted for the ADC 08131 and the ADC08134 is 140˚C/W and 91˚C/W for the ADC08138. Note 6: Human body model, 100 pF capacitor discharged through a 1.5 kΩ resistor. Note 7: See AN450 “Surface Mounting Methods and Their Effect on Product Reliability” or Linear Data Book section “Surface Mount” for other methods of soldering surface mount devices. Note 8: Typicals are at TJ = 25˚C and represent the most likely parametric norm. Note 9: Guaranteed to National’s AOQL (Average Outgoing Quality Level). Note 10: Total unadjusted error includes zero, full-scale, linearity, and multiplexer error. Total unadjusted error with VREF = +5V only applies to the ADC08134 and ADC08138. See (Note 16). Note 11: Cannot be tested for the ADC08131. Note 12: For VIN(−) ≥ VIN(+) the digital code will be 0000 0000. Two on-chip diodes are tied to each analog input (see Block Diagram) which will forward-conduct for analog input voltages one diode drop below ground or one diode drop greater than VCC supply. During testing at low VCC levels (e.g., 4.5V), high level analog inputs (e.g., 5V) can cause an input diode to conduct, especially at elevated temperatures. This will cause errors for analog inputs near full-scale. The specification allows 50 mV forward bias of either diode; this means that as long as the analog VIN does not exceed the supply voltage by more than 50 mV, the output code will be correct. Exceeding this range on an unselected channel will corrupt the reading of a selected channel. Achievement of an absolute 0 VDC to 5 VDC input voltage range will therefore require a minimum supply voltage of 4.950 VDC over temperature variations, initial tolerance and loading. Note 13: Channel leakage current is measured after a single-ended channel is selected and the clock is turned off. For off channel leakage current the following two cases are considered: one, with the selected channel tied high (5 VDC) and the remaining seven off channels tied low (0 VDC), total current flow through the off channels is measured; two, with the selected channel tied low and the off channels tied high, total current flow through the off channels is again measured. The two cases considered for determining on channel leakage current are the same except total current flow through the selected channel is measured. Note 14: A 40% to 60% duty cycle range insures proper operation at all clock frequencies. In the case that an available clock has a duty cycle outside of these limits the minimum time the clock is high or low must be at least 450 ns. The maximum time the clock can be high or low is 100 µs. Note 15: Since data, MSB first, is the output of the comparator used in the successive approximation loop, an additional delay is built in (see Block Diagram) to allow for comparator response time. Note 16: For the ADC08131 VREFIN is internally tied to the on chip 2.5V band-gap reference output; therefore, the supply current is larger because it includes the reference current (700 µA typical, 2 mA maximum). Note 17: Load regulation test conditions and specifications for the ADC08131 differ from those of the ADC08134 and ADC08138 because the ADC08131 has the on-board reference as a permanent load. 5 www.national.com ADC08138 Simplified Block Diagram DS010749-1 www.national.com 6 Typical Converter Performance Characteristics Linearity Error vs Reference Voltage Linearity Error vs Temperature Linearity Error vs Clock Frequency DS010749-27 DS010749-28 DS010749-29 Power Supply Current vs Temperature (ADC08138, ADC08134) Output Current vs Temperature Power Supply Current vs Clock Frequency DS010749-31 DS010749-30 DS010749-32 Note: For ADC08131 add IREF Typical Reference Performance Characteristics Load Regulation Line Regulation (3 Typical Parts) Output Drift vs Temperature (3 Typical Parts) DS010749-34 DS010749-33 DS010749-35 7 www.national.com Typical Reference Performance Characteristics Available Output Current vs Supply Voltage (Continued) DS010749-36 TRI-STATE Test Circuits and Waveforms t1H t1H DS010749-39 DS010749-37 t0H t0H DS010749-40 DS010749-38 Timing Diagrams Data Input Timing DS010749-9 standards ADC0831/4/8. *To reset these devices, CLK and CS must be simultaneously high for a period of tSELECT or greater. Otherwise these devices are compatible with industry www.national.com 8 Timing Diagrams (Continued) Data Output Timing DS010749-10 ADC08131 Start Conversion Timing DS010749-11 ADC08131 Timing DS010749-12 *LSB first output not available on ADC08131. LSB information is maintained for remainder of clock periods until CS goes high. ADC08134 Timing DS010749-13 9 www.national.com www.national.com Timing Diagrams ADC08138 Timing (Continued) 10 DS010749-14 *Make sure clock edge #18 clocks in the LSB before SE is taken low ADC08138 Functional Block Diagram 11 DS010749-15 *Some of these functions/pins are not available with other options. www.national.com Note 18: For the ADC08134, the “SEL 1” Flip-Flop is bypassed. For the ADC08131, VREFOUT and VREFIN are internally tied together. Functional Description MULTIPLEXER ADDRESSING The design of these converters utilizes a comparator structure with built-in sample-and-hold which provides for a differential analog input to be converted by a successiveapproximation routine. The actual voltage converted is always the difference between an assigned “+” input terminal and a “−” input terminal. The polarity of each input terminal of the pair indicates which line the converter expects to be the most positive. If the assigned “+” input voltage is less than the “−” input voltage the converter responds with an all zeros output code. A unique input multiplexing scheme has been utilized to provide multiple analog channels with software-configurable single-ended, differential, or pseudo-differential (which will convert the difference between the voltage at any analog input and a common terminal) operation. The analog signal conditioning required in transducer-based data acquisition systems is significantly simplified with this type of input flexibility. One converter package can now handle ground referenced inputs and true differential inputs as well as signals with some arbitrary reference voltage. A particular input configuration is assigned during the MUX addressing sequence, prior to the start of a conversion. The MUX address selects which of the analog inputs are to be enabled and whether this input is single-ended or differential. Differential inputs are restricted to adjacent channel pairs. For example, channel 0 and channel 1 may be selected as a differential pair but channel 0 or 1 cannot act differentially with any other channel. In addition to selecting differential mode the polarity may also be selected. Channel 0 may be selected as the positive input and channel 1 as the negative input or vice versa. This programmability is best illustrated by the MUX addressing codes shown in the following tables for the various product options. The MUX address is shifted into the converter via the DI line. Because the ADC08131 contains only one differential input channel with a fixed polarity assignment, it does not require addressing. The common input line (COM) on the ADC08138 can be used as a pseudo-differential input. In this mode the voltage on this pin is treated as the “−” input for any of the other input channels. This voltage does not have to be analog ground; it can be any reference potential which is common to all of the inputs. This feature is most useful in single-supply applications where the analog circuity may be biased up to a potential other than ground and the output signals are all referred to this potential. TABLE 1. Multiplexer/Package Options Part Number ADC08131 ADC08134 ADC08138 Number of Analog Channels Single-Ended 1 4 8 Differential 1 2 4 Number of Package Pins 8 14 20 TABLE 2. MUX Addressing: ADC08138 Single-Ended MUX Mode MUX Address START 1 1 1 1 1 1 1 1 SGL/ DIF 1 1 1 1 1 1 1 1 ODD/ SIGN 0 0 0 0 1 1 1 1 SELECT 1 0 0 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 + + + + + + + + − − − − − − − − 0 1 2 Analog Single-Ended Channel # 3 4 5 6 7 COM TABLE 3. MUX Addressing: ADC08138 Differential MUX Mode MUX Address START 1 1 1 1 1 1 SGL/ DIF 0 0 0 0 0 0 ODD/ SIGN 0 0 0 0 1 1 SELECT 1 0 0 1 1 0 0 0 0 1 0 1 0 1 − + − + 0 + 0 1 − + − + − + − 2 Analog Differential Channel-Pair # 1 3 4 2 5 6 3 7 www.national.com 12 Functional Description Differential MUX Mode MUX Address START 1 1 SGL/ DIF 0 0 ODD/ SIGN 1 1 (Continued) TABLE 3. MUX Addressing: ADC08138 (Continued) Analog Differential Channel-Pair # SELECT 1 1 1 0 0 1 0 0 1 2 1 3 4 − 2 5 + − + 6 3 7 TABLE 4. MUX Addressing: ADC08134 Single-Ended MUX Mode MUX Address START 1 1 1 1 SGL/ DIF 1 1 1 1 ODD/ SIGN 0 0 1 1 SELECT 1 0 1 0 1 + + + + 0 Channel # 1 2 3 COM is internally tied to AGND Differential MUX Mode MUX Address START 1 1 1 1 SGL/ DIF 0 0 0 0 ODD/ SIGN 0 0 1 1 SELECT 1 0 1 0 1 − + − + + − + − 0 Channel # 1 2 3 Since the input configuration is under software control, it can be modified as required before each conversion. A channel can be treated as a single-ended, ground referenced input for one conversion; then it can be reconfigured as part of a differential channel for another conversion. Figure 1 illustrates the input flexibility which can be achieved. The analog input voltages for each channel can range from 50 mV below ground to 50 mV above VCC (typically 5V) without degrading conversion accuracy. THE DIGITAL INTERFACE A most important characteristic of these converters is their serial data link with the controlling processor. Using a serial communication format offers two very significant system improvements; it allows many functions to be included in a small package and it can eliminate the transmission of low level analog signals by locating the converter right at the analog sensor; transmitting highly noise immune digital data back to the host processor. To understand the operation of these converters it is best to refer to the Timing Diagrams and Functional Block Diagram and to follow a complete conversion sequence. For clarity a separate timing diagram is shown for each device. 1. A conversion is initiated by pulling the CS (chip select) line low. This line must be held low for the entire conversion. The converter is now waiting for a start bit and its MUX assignment word. 2. On each rising edge of the clock the status of the data in (DI) line is clocked into the MUX address shift register. 13 The start bit is the first logic “1” that appears on this line (all leading zeros are ignored). Following the start bit the converter expects the next 2 to 4 bits to be the MUX assignment word. 3. When the start bit has been shifted into the start location of the MUX register, the input channel has been assigned and a conversion is about to begin. An interval of 1⁄2 clock period is automatically inserted to allow for sampling the analog input. The SARS line goes high at the end of this time to signal that a conversion is now in progress and the DI line is disabled (it no longer accepts data). 4. The data out (DO) line now comes out of TRI-STATE and provides a leading zero. 5. During the conversion the output of the SAR comparator indicates whether the analog input is greater than (high) or less than (low) a series of successive voltages generated internally from a ratioed capacitor array (first 5 bits) and a resistor ladder (last 3 bits). After each comparison the comparator’s output is shipped to the DO line on the falling edge of CLK. This data is the result of the conversion being shifted out (with the MSB first) and can be read by the processor immediately. 6. After 8 clock periods the conversion is completed. The SARS line returns low to indicate this 1⁄2 clock cycle later. www.national.com Functional Description 7. (Continued) 8. is an exception in that its data is only output in MSB first format. All internal registers are cleared when the CS line is high and the tSELECT requirement is met. See Data Input Timing under Timing Diagrams. If another conversion is desired CS must make a high to low transition followed by address information. The DI and DO lines can be tied together and controlled through a bidirectional processor I/O bit with one wire. This is possible because the DI input is only “looked-at” during the MUX addressing interval while the DO line is still in a high impedance state. The stored data in the successive approximation register is loaded into an internal shift register. If the programmer prefers the data can be provided in an LSB first format [this makes use of the shift enable (SE) control line]. On the ADC08138 the SE line is brought out and if held high the value of the LSB remains valid on the DO line. When SE is forced low the data is clocked out LSB first. On devices which do not include the SE control line, the data, LSB first, is automatically shifted out the DO line after the MSB first data stream. The DO line then goes low and stays low until CS is returned high. The ADC08131 8 Single-Ended 4 Differential DS010749-43 DS010749-41 8 Psuedo-Differential Mixed Mode DS010749-42 DS010749-44 FIGURE 1. Analog Input Multiplexer Options for the ADC08138 REFERENCE CONSIDERATIONS The VREFIN pin on these converters is the top of a resistor divider string and capacitor array used for the successive approximation conversion. The voltage applied to this reference input defines the voltage span of the analog input (the difference between VIN(MAX) and VIN(MIN) over which the 256 possible output codes apply). The reference source must be capable of driving the reference input resistance, which can be as low as 1.3 kΩ. For absolute accuracy, where the analog input varies between specific voltage limits, the reference input must be biased with a stable voltage source. The ADC08134 and the ADC08138 provide the output of a 2.5V band-gap reference at VREFOUT. This voltage does not vary appreciably with www.national.com 14 temperature, supply voltage, or load current (see Reference Characteristics in the Electrical Characteristics tables) and can be tied directly to VREFIN for an analog input span of 0V to 2.5V. This output can also be used to bias external circuits and can therefore be used as the reference in ratiometric applications. Bypassing VREFOUT with a 100 µF capacitor is recommended. For the ADC08131, the output of the on-board reference is internally tied to the reference input. Consequently, the analog input span for this device is set at 0V to 2.5V. The pin VREFC is provided for bypassing purposes and biasing external circuits as suggested above. The maximum value of the reference is limited to the VCC supply voltage. The minimum value, however, can be quite Functional Description (Continued) small (see Typical Performance Characteristics) to allow direct conversions of transducer outputs providing less than a 5V output span. Particular care must be taken with regard to noise pickup, circuit layout and system error voltage sources when operating with a reduced span due to the increased sensitivity of the converter (1 LSB equals VREF/256). DS010749-18 DS010749-17 b) Absolute a) Ratiometric FIGURE 2. Reference Examples THE ANALOG INPUTS The most important feature of these converters is that they can be located right at the analog signal source and through just a few wires can communicate with a controlling processor with a highly noise immune serial bit stream. This in itself greatly minimizes circuitry to maintain analog signal accuracy which otherwise is most susceptible to noise pickup. However, a few words are in order with regard to the analog inputs should the input be noisy to begin with or possibly riding on a large common-mode voltage. The differential input of these converters actually reduces the effects of common-mode input noise, a signal common to both selected “+” and “−” inputs for a conversion (60 Hz is most typical). The time interval between sampling the “+” input and then the “−” input is 1⁄2 of a clock period. The change in the common-mode voltage during this short time interval can cause conversion errors. For a sinusoidal common-mode signal this error is: amp RC active low pass filter can provide both impedance buffering and noise filtering should a high impedance signal source be required. OPTIONAL ADJUSTMENTS Zero Error The zero of the A/D does not require adjustment. If the minimum analog input voltage value, VIN(MIN), is not ground a zero offset can be done. The converter can be made to output 0000 0000 digital code for this minimum input voltage by biasing any VIN (−) input at this VIN(MIN) value. This utilizes the differential mode operation of the A/D. The zero error of the A/D converter relates to the location of the first riser of the transfer function and can be measured by grounding the VIN (−) input and applying a small magnitude positive voltage to the VIN (+) input. Zero error is the difference between the actual DC input voltage which is necessary to just cause an output digital code transition from 0000 0000 to 0000 0001 and the ideal 1⁄2 LSB value (1⁄2 LSB = 9.8mV for VREF = 5.000VDC). Full Scale A full-scale adjustment can be made by applying a differential input voltage which is 11⁄2 LSB down from the desired analog full-scale voltage range and then adjusting the magnitude of the VREFIN input for a digital output code which is just changing from 1111 1110 to 1111 1111 (See figure entitled “Span Adjust; 0V ≤ VIN ≤ 3V”). This is possible only with the ADC08134 and ADC08138. (The reference is internally connected to VREFIN of the ADC08131). where fCM is the frequency of the common-mode signal, VPEAK is its peak voltage value and fCLK is the A/D clock frequency. For a 60Hz common-mode signal to generate a 1⁄4 LSB error (≈5 mV) with the converter running at 250kHz, its peak value would have to be 6.63V which would be larger than allowed as it exceeds the maximum analog input limits. Source resistance limitation is important with regard to the DC leakage currents of the input multiplexer. While operating near or at maximum speed bypass capacitors should not be used if the source resistance is greater than 1kΩ. The worst-case leakage current of ± 1µA over temperature will create a 1mV input error with a 1kΩ source resistance. An op 15 www.national.com Functional Description (Continued) Adjusting for an Arbitrary Analog Input Voltage Range If the analog zero voltage of the A/D is shifted away from ground (for example, to accommodate an analog input signal which does not go to ground), this new zero reference should be properly adjusted first. A VIN (+) voltage which equals this desired zero reference plus 1⁄2 LSB (where the LSB is calculated for the desired analog span, using 1 LSB = analog span/256) is applied to selected “+” input and the zero reference voltage at the corresponding “−” input should then be adjusted to just obtain the 00HEX to 01HEX code transition. The full-scale adjustment should be made [with the proper VIN (−) voltage applied] by forcing a voltage to the VIN (+) input which is given by: where: VMAX = the high end of the analog input range and VMIN = the low end (the offset zero) of the analog range. (Both are ground referenced.) The VREFIN (or VCC) voltage is then adjusted to provide a code change from FEHEX to FFHEX. This completes the adjustment procedure. Applications A “Stand-Alone” Hook-Up for ADC08138 Evaluation DS010749-45 *Pinouts shown for ADC08138. For all other products tie to pin functions as shown. www.national.com 16 Applications (Continued) Low-Cost Remote Temperature Sensor DS010749-46 Protecting the Input DS010749-22 Diodes are 1N914 17 www.national.com Applications (Continued) Operating with Ratiometric Transducers DS010749-23 *VIN(−) = 0.15 VREF 15% of VREF ≤ VXDR ≤ 85% of VREF Span Adjust; 0V ≤ VIN ≤ 3V DS010749-24 www.national.com 18 Applications (Continued) Zero-Shift and Span Adjust: 2V ≤ VIN ≤ 5V DS010749-25 19 www.national.com Physical Dimensions inches (millimeters) unless otherwise noted Order Number ADC08134CIWM NS Package Number M14B www.national.com 20 ADC08131/ADC08134/ADC08138 8-Bit High-Speed Serial I/O A/D Converters with Multiplexer Options, Voltage Reference, and Track/Hold Function Physical Dimensions inches (millimeters) unless otherwise noted (Continued) Order Number ADC08138CIWM NS Package Number M20B LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 1 80-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 1 80-530 85 85 English Tel: +49 (0) 1 80-532 78 32 Français Tel: +49 (0) 1 80-532 93 58 Italiano Tel: +49 (0) 1 80-534 16 80 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: sea.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.