COP8ACC520N8

COP8ACC Family 8-Bit CMOS ROM Based and OTP Microcontrollers with 4k or 16k Memory and High Resolution A/D July 2000 COP8ACC Family 8-Bit CMOS ROM Based and OTP Microcontrollers with 4k or 16k Memory and High Resolution A/D General Description The COP8ACC Family ROM based microcontrollers are highly integrated COP8™ Feature core devices with 4k memory and advanced features including a High-Resolution A/D. These single-chip CMOS devices are suited for applications requiring a full featured, low EMI controller with an A/D (only one external capacitor required). COP8ACC7 devices are pin and software compatible (different VCC range) 16k OTP EPROM versions for pre-production. Erasable windowed versions are available for use with a range of COP8 software and hardware development tools. Device COP8ACC5xxx9 COP8ACC5xxx8 COP8ACC7xxx9 COP8ACC7xxx8 Memory (bytes) 4k ROM 4k ROM 16k OTP EPROM 16k OTP EPROM RAM (bytes) 128 128 128 128 Family features include an 8-bit memory mapped architecture, 4 MHz CKI with 2.5µs instruction cycle, 6 channel A/D with 12-bit resolution, analog capture timer, analog current source and VCC/2 reference, one multi-function 16-bit timer/ counter, MICROWIRE/PLUS serial I/O, two power saving HALT/IDLE modes, MIWU, high current outputs, software selectable I/O options, WATCHDOG™ timer and Clock Monitor, Low EMI 2.5V to 5.5V operation and 20/28 pin packages. Devices included in this datasheet are: I/O Pins 15/23 15/23 15/23 15/23 Packages 20 SOIC, 28 DIP/SOIC 20 SOIC, 28 DIP/SOIC 20 SOIC, 28 DIP/SOIC 20 SOIC, 28 DIP/SOIC Temperature 0 to +70˚C -40 to +85˚C 0 to +70˚C -40 to +85˚C Key Features n Analog Function Block with 12-bit A/D including — Analog comparator with seven input mux — Constant Current Source and VCC/2 Reference — 16-bit capture timer (upcounter) clocked from CKI with auto reset on timer startup n Quiet design (reduced radiated emissions) n 4096 bytes on-board ROM or 16,384 OTP EPROM with security feature n 128 bytes on-board RAM CPU/Instruction Set Features n 2.5 µs instruction cycle time n Eight multi-source vectored interrupt servicing — External Interrupt — Idle Timer T0 — Timer T1 associated Interrupts — MICROWIRE/PLUS — Multi-Input Wake Up — Software Trap — Default VIS — A/D (Capture Timer) n 8-bit Stack Pointer (SP) — stack in RAM n Two 8-bit Registers Indirect Data Memory Pointers (B and X) Additional Peripheral Features n Idle Timer n One 16-bit timer with two 16-bit registers supporting: — Processor Independent PWM mode — External Event counter mode — Input Capture mode n Multi-Input Wake-Up (MIWU) with optional interrupts n WATCHDOG and clock monitor logic n MICROWIRE/PLUS™ serial I/O with programmable shift clock-polarity Fully Static CMOS n n n n Two power saving modes: HALT and IDLE Single supply operation: 2.5V to 5.5V for COP8ACC5 Single supply operation: 2.7V to 5.5V for COP8ACC7 Temperature ranges: 0˚C to +70˚C, −40˚C to +85˚C I/O Features n Software selectable I/O options (Push-Pull Output, Weak Pull-Up Input, High Impedance Input) n High current outputs n Schmitt Trigger inputs on ports G and L n Packages: 28 DIP/SO with 23 I/O pins, 20 SO with 15 I/O pins Development System n Emulation and OTP devices n Real time emulation and full program debug offered by MetaLink development system Applications n Battery Chargers n Appliances n Data Acquisition systems COP8™, MICROWIRE™, MICROWIRE/PLUS™, and WATCHDOG™ are trademarks of National Semiconductor Corporation. TRI-STATE ® is a registered trademark of National Semiconductor Corporation. iceMASTER ® is a registered trademark of MetaLink Corporation. © 2001 National Semiconductor Corporation DS012865 www.national.com COP8ACC Family Block Diagram DS012865-1 FIGURE 1. Block Diagram Connection Diagrams DS012865-3 DS012865-2 Note: -X Crystal Oscillator Note: -E Halt Enable Top View Order Number COP8ACC528N9 or COP8ACC528N8 See NS Molded Package Number N28A Order Number COP8ACC528M9 or COP8ACC528M8 Order Number COP8ACC728N9-XE or COP8ACC728N8-XE Order Number COP8ACC728M9-XE or COP8ACC728M8-XE See NS Molded Package Number M28B Top View Order Number COP8ACC520M9 or COP8ACC520N8 Order Number COP8ACC720M9-XE or COP8ACC720N8-XE See NS Molded Package Number M20B FIGURE 2. Connection Diagrams www.national.com 2 COP8ACC Family Connection Diagrams Port L4 L5 L6 L7 G0 G1 G2 G3 G4 G5 G6 G7 D0 D1 D2 D3 I0 I1 I2 I3 I4 I5 I6 I7 VCC GND CKI RESET I/O I/O I/O I/O I/O WDOUT I/O I/O I/O I/O I I/CKO O O O O I I I I I I I I Type (Continued) Pinouts for 28-Pin, 20-Pin Packages Alt. Fun MIWU MIWU MIWU MIWU INT T1B T1A SO SK SI HALT Restart Alt. Fun Ext. Int. Ext. Int. Ext. Int. Ext. Int. 28-Pin DIP/SO 4 5 6 7 23 24 25 26 27 28 1 2 11 12 13 14 Analog CH1 ISRC Analog CH2 Analog CH3 Analog CH4 Analog CH5 Analog CH6 COUT 15 16 17 18 19 20 21 22 9 8 3 10 5 4 3 6 10 11 12 13 14 15 16 17 18 19 20 1 2 7 8 9 20-Pin SO Ordering Inforamtion DS012865-38 FIGURE 3. Part Numbering Scheme 3 www.national.com COP8ACC Family Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (VCC) Voltage at Any Pin 7V −0.3V to VCC +0.3V Total Current into VCC Pin (Source) Total Current out of GND Pin (Sink) Storage Temperature Range 100 mA 110 mA −65˚C to +140˚C Note 1: Absolute maximum ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications are not ensured when operating the device at absolute maximum ratings. DC Electrical Characteristics 0˚C ≤ TA ≤ +70˚C unless otherwise specified [OTP Value] Parameter Operating Voltage Power Supply Ripple (Note 2) Supply Current (Note 3) CKI = 4 MHz CKI = 4 MHz CKI = 1 MHz HALT Current (Note 4) IDLE Current CKI = 4 MHz CKI = 1 MHz Input Levels (VIH, VIL) RESET Logic High Logic Low CKI, All Other Inputs Logic High Logic Low Hi-Z Input Leakage Input Pullup Current G and L Port Input Hysteresis Output Current Levels D Outputs Source Sink All Others Source (Weak Pull-Up Mode) Source (Push-Pull Mode) Sink (Push-Pull Mode) TRI-STATE ® Leakage VCC = 4V, VOH = 2.7V VCC = 2.5V [2.7V], VOH = 1.8V VCC= 4V, VOH = 3.3V VCC = 2.5V [2.7V], VOH = 1.8V VCC = 4V, VOL = 0.4V VCC = 2.5V [2.7V], VOL = 0.4V VCC = 5.5V Allowable Sink/Source Current per Pin D Outputs (Sink) All others Maximum Input Current without Latchup (Note 5) RAM Retention Voltage, Vr www.national.com Conditions Peak-to-Peak Min 2.5 [2.7] Typ Max 5.5 0.1 VCC Units V V mA mA mA µA µA mA mA VCC = 5.5V, tC = 2.5 µs VCC = 4V, tC = 2.5 µs VCC = 4V, tC = 10 µs VCC = 5.5V, CKI = 0 MHz VCC = 4V, CKI = 0 MHz VCC = 5.5V, tC = 2.5 µs VCC = 4V, tC = 10 µs 5.5 [9.5] 2.5 [6.5] 1.4 [5.4] VCC (the pins do not have source current when biased at a voltage below VCC). The effective resistance to VCC is 750Ω (typical). These two pins will not latch up. The voltage at the pins must be limited to less than 14V. WARNING: Voltages in excess of 14V will cause damage to the pins. This warning excludes ESD transients. Note 6: The output propagation delay is referenced to the end of the instruction cycle where the output change occurs. Note 7: Parameter characterized but not tested. Note 8: tC = Instruction Cycle Time. 5 www.national.com COP8ACC Family Absolute Maximum Ratings (Note 9) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (VCC) Voltage at Any Pin 7V −0.3V to VCC +0.3V Total Current into VCC Pin (Source) Total Current out of GND Pin (Sink) Storage Temperature Range 100 mA 110 mA −65˚C to +140˚C Note 9: Absolute maximum ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications are not ensured when operating the device at absolute maximum ratings. DC Electrical Characteristics −40˚C ≤ TA ≤ +85˚C unless otherwise specified [OTP Value] Parameter Operating Voltage Power Supply Ripple (Note 10) Supply Current (Note 11) CKI = 4 MHz CKI = 4 MHz CKI = 1 MHz HALT Current (Note 12) IDLE Current CKI = 4 MHz CKI = 1 MHz Input Levels (VIH, VIL) RESET Logic High Logic Low CKI, All Other Inputs Logic High Logic Low Hi-Z Input Leakage Input Pullup Current G and L Port Input Hysteresis Output Current Levels D Outputs Source Sink All Others Source (Weak Pull-Up Mode) Source (Push-Pull Mode) Sink (Push-Pull Mode) TRI-STATE Leakage Allowable Sink/Source Current per Pin D Outputs (Sink) All others Maximum Input Current without Latchup (Note 13) RAM Retention Voltage, Vr www.national.com Conditions Peak-to-Peak VCC = 5.5V, tC = 2.5 µs VCC = 4V, tC = 2.5 µs VCC = 4V, tC = 10 µs VCC = 5.5V, CKI = 0 MHz VCC = 4V, CKI = 0 MHz VCC = 5.5V, tC = 2.5 µs VCC = 4V, tC = 10 µs Min 2.5 [2.7] Typ Max 5.5 0.1 VCC 5.5 [9.5] 2.5 [6.5] 1.4 [5.4] Units V V mA mA mA µA µA mA mA