LM122

LM122 LM322 LM3905 Precision Timers February 1995 LM122 LM322 LM3905 Precision Timers General Description The LM122 series are precision timers that offer great versatility with high accuracy They operate with unregulated supplies from 4 5V to 40V while maintaining constant timing periods from microseconds to hours Internal logic and regulator circuits complement the basic timing function enabling the LM122 series to operate in many different applications with a minimum of external components The output of the timer is a floating transistor with built in current limiting It can drive either ground referred or supply referred loads up to 40V and 50 mA The floating nature of this output makes it ideal for interfacing lamp or relay driving and signal conditioning where an open collector or emitter is required A ‘‘logic reverse’’ circuit can be programmed by the user to make the output transistor either ‘‘on’’ or ‘‘off’’ during the timing period The trigger input to the LM122 series has a threshold of 1 6V independent of supply voltage but it is fully protected against inputs as high as g 40V even when using a 5V supply The circuitry reacts only to the rising edge of the trigger signal and is immune to any trigger voltage during the timing periods An internal 3 15V regulator is included in the timer to reject supply voltage changes and to provide the user with a convenient reference for applications other than a basic timer External loads up to 5 mA can be driven by the regulator An internal 2V divider between the reference and ground sets the timing period to 1 RC The timing period can be voltage controlled by driving this divider with an external source through the VADJ pin Timing ratios of 50 1 can be easily achieved The comparator used in the LM122 utilizes high gain PNP input transistors to achieve 300 pA typical input bias current over a common mode range of 0V to 3V A boost terminal allows the user to increase comparator operating current for timing periods less than 1 ms This lets the timer operate over a 3 ms to multi-hour timing range with excellent repeatability The LM122 operates over a temperature range of b55 C to a 125 C An electrically identical LM322 is specified from 0 C to a 70 C The LM3905 is identical to the LM122 series except that the boost and VADJ pin options are not available limiting minimum timing period to 1 ms Features Y Y Y Y Y Y Y Y Y Y Immune to changes in trigger voltage during timing interval Timing periods from microseconds to hours Internal logic reversal Immune to power supply ripple during the timing interval Operates from 4 5V to 40V supplies Input protected to g 40V Floating transistor output with internal current limiting Internal regulated reference Timing period can be voltage controlled TTL compatible input and output Connection Diagrams Metal Can Package Dual-In-Line Package Dual-In-Line Package TL H 7768–6 Top View Order Number LM122H See NS Package Number H10C TL H 7768 – 8 TL H 7768 – 7 Top View Order Number LM322N See NS Package Number N14A Top View Order Number LM3905N See NS Package Number N08E C1995 National Semiconductor Corporation TL H 7768 RRD-B30M115 Printed in U S A Absolute Maximum Ratings If Military Aerospace specified devices are required please contact the National Semiconductor Sales Office Distributors for availability and specifications Power Dissipation a V Voltage Collector Output Voltage VREF Current Trigger Voltage VADJ Voltage (Forced) 500 mW 40V 40V 5 mA g 40V 5V Logic Reverse Voltage Output Short Circuit Duration (Note 1) Lead Temperature (Soldering 10 sec ) Operating Temperature Range LM122 LM322 LM3905 260 C b 55 C s TA s a 125 C 0 C s TA s a 70 C 0 C s TA s a 70 C 5 5V Electrical Characteristics (Note 2) Parameter Timing Ratio Comparator Input Current Trigger Voltage Trigger Current Supply Current Timing Ratio Comparator Input Current Trigger Voltage Trigger Current Output Leakage Current Capacitor Saturation Voltage Reset Resistance Reference Voltage Reference Regulation Collector Saturation Voltage Emitter Saturation Voltage Average Temperature Coefficient of Timing Ratio Minimum Trigger Width VTRIG e 3V TA e 25 C 0 s IOUT s 3 mA 4 5V s V a s 40V IL e 8 mA IL e 50 mA TA e 25 C IL e 3 mA TA e 25 C IL e 50 mA 3 Conditions Min LM122 Typ Max Min LM322 Typ Max Min LM3905 Typ Max Units TA e 25 C 4 5V s V a s 40V 0 626 0 632 0 638 0 620 0 632 0 644 0 620 0 632 0 644 Boost Tied to V a (Note 3) 0 620 0 632 0 644 0 620 0 632 0 644 TA e 25 C 4 5V s V a s 40V Boost Tied to V a TA e 25 C 4 5V s V a s 40V TA e 25 C VTRIG e 2V TA t 25 C 4 5V s V a s 40V 4 5V s V a s 40V Boost Tied to V a 4 5V s V a s 40V Boost Tied to V a (Note 4) 4 5V s V a s 40V VTRIG e 2 5V VCE e 40V Rt t 1 MX Rt e 10 kX 25 25 150 3 15 20 6 0 25 07 18 21 0 003 0 25 33 50 25 04 14 22 3 3 0 62 0 62 b5 03 30 12 16 25 25 10 100 2 12 03 30 16 25 15 100 2 12 05 16 25 15 2 nA nA V mA 4 0 644 0 644 5 100 25 200 1 0 61 0 61 b2 25 45 0 654 0 654 2 150 25 200 5 0 61 b2 5 25 45 0 654 25 25 200 5 mA nA nA V mA mA mV mV X 08 08 08 25 25 150 3 15 20 6 0 25 07 18 21 0 003 0 25 33 50 25 04 14 22 3 3 25 25 150 3 15 20 6 0 25 07 18 21 0 003 0 25 33 50 25 04 14 22 3 V mV mV V V V V %C ms Note 1 Continuous output shorts are not allowed Short circuit duration at ambient temperatures up to 40 C may be calculated from t e 120 VCE seconds where VCE is the collector to emitter voltage across the output transistor during the short Note 2 These specifications apply for TAMIN s TA s TAMAX unless otherwise noted Note 3 Output pulse width can be calculated from the following equation t e (Rt) (Ct) 1 b 2(0 632 b r) b VC VREF) where r is timing ratio and VC is capacitor saturation voltage This reduces to t e (Rt) (Ct) for all but the most critical applications Note 4 Sign reversal may occur at high temperatures ( l 100 C) where comparator input current is predominately leakage See typcial curves Note 5 Refer to RETS122X drawing of military LM122H version for specifications 2 Typical Performance Characteristics Comparator Bias Current Comparator Bias Current Comparator Bias Current (LM122 LM322) TL H 7768 – 3 Supply Current Trigger Input Characteristics Trigger Threshold Output Transistor Saturation Characteristics at Low Currents Collector Output Saturation Characteristics at High Current Timing Error Due to Comparator Bias Current Reference Regulation Reference Regulation Suggested Timing Components Short Output Pulse (LM122 LM322) Short Output Pulse (LM122 LM322) Logic Pin Characteristics TL H 7768 – 4 3 4 TL H 7768 – 5 Schematic Diagram Functional Diagram TL H 7768 – 9 Timing Diagram TL H 7768 – 10 Pin Function Description One of the main features of the LM122 is its great versatility Since this device is unique a description of the functions and limitations of each pin is in order This will make it much easier to follow the discussion of the various applications presented in this note V a is the positive supply terminal of the LM122 When using a single supply this terminal may be driven by any voltage between 4 5V and 40V The effect of supply variations on timing period is less than 0 005% V so supplies with high ripple content may be used without causing pulse width changes Supply bypassing on V a is not generally needed but may be necessary when driving highly reactive loads Quiescent current drawn from the V a terminal is typically 2 5 mA independent of the supply voltage Of course additional current will be drawn if the reference is externally loaded The VREF pin is the output of a 3 15V series regulator referenced to the ground pin Up to 5 0 mA can be drawn from this pin for driving external networks In most applications the timing resistor is tied to VREF but it need not be in situations where a more linear charging current is required The regulated voltage is very useful in applications where the LM122 is not used as a timer such as switching regulators variable reference comparators and temperature con- 5 Pin Function Description (Continued) trollers Typical temperature drift of the reference is less than 0 01% C The trigger terminal is used to start a timing cycle (see functional diagram) Initially Q1 is saturated Ct is discharged and the latching buffer output (V1) is latched high A trigger pulse unlatches the buffer V1 goes low and turns Q1 off The timing capacitor Ct connected from R C to GND will begin to charge When the voltage at the R C terminal reaches the 2 0V threshold of the comparator the comparator toggles latching the buffer output (V1) in the high state This turns on Q1 discharges the capacitor Ct and the cycle is ready to begin again If the trigger is held high as the timing period ends the comparator will toggle and V1 will go high exactly as before However V1 will not be latched and the capacitor will not discharge until the trigger again goes low When the trigger goes low V1 remains high but is now latched Trigger threshold is typically 1 6V at 25 C and has a temperature dependence of b5 0 mV C Current drawn from the trigger source is typically 20 mA at threshold rising to 600 mA at 30V then leveling off due to FET action of the series resistor R5 For negative input trigger voltages the only current drawn is leakage in the nA region The trigger can be driven from supplies as high as g 40V even when device supply voltage is only 5V The R C pin is tied to the non-inverting side of the comparator and to the collector of Q1 Timing ends when the voltage on this pin reaches 2 0V (1 RC time constant referenced to the 3 15V regulator) Q1 turns on only if the trigger voltage has dropped below threshold In comparator or regulator applications of the timer the trigger is held permanently high and the R C pin acts just like the input to an ordinary comparator The maximum voltages which can be applied to this pin are a 5 5V and b0 7V Current from the R C pin is typically 300 pA when the voltage is negative with respect to the VADJ terminal For higher voltages the current drops to leakage levels In the boosted mode input current is typically 30 nA Gain of the comparator is very high 200 000 or more depending on the state of the logic reverse pin and the connection of the output transistor The ground pin of the LM122 need not necessarily be tied to system ground It can be connected to any positive or negative voltage as long as the supply is negative with respect to the V a terminal Level shifting may be necessary for the input trigger if the trigger voltage is referred to system ground This can be done by capacitive coupling or by actual resistive or active level shifting One point must be kept in mind the emitter output must not be held above the ground terminal with a low source impedance This could occur for instance if the emitter were grounded when the ground pin of the LM122 was tied to a negative supply The terminal labled VADJ is tied to one side of the comparator and to a voltage divider between VREF and ground The divider voltage is set at 63 2% of VREF with respect to ground exactly one RC time constant The impedance of the divider is increased to about 30k with a series resistor to present a minimum load on external signals tied to VADJ This resistor is a pinched type with a typical variation in nominal value of b50% a 100% and a TC of 0 7% C For this reason external signals (typically a pot between VREF and ground) connected to VADJ should have a source resistance as low as possible For small changes in VADJ up to several kX is all right but for large variations 250X or less should be maintained This can be accomplished with a 1k pot since the maximum impedance from the wiper is 250X If a voltage is forced on VADJ from a hard source voltage should be limited to b0 5 and a 5 0V or current limited to g 1 0 mA This includes capacitively coupled signals because even small values of capacitors contain enough energy to degrade the input stage if the capacitor is driven with a large fast slewing signal The VADJ pin may be used to abort the timing cycle Grounding this pin during the timing period causes the timer to react just as if the capacitor voltage had reached its normal RC trigger point the capacitor discharges and the output charges state An exception to this occurs if the trigger pin is held high when the VADJ pin is grounded In this case the output changes state but the capacitor does not discharge If the trigger drops while VADJ is being held low discharge will occur immediately and the cycle will be over If the trigger is still high when VADJ is released the output may or may not change state depending on the voltage across the timing capacitor For voltages below 2 0V across the timing capacitor the output will change state immediately then once more as the voltage rises past 2 0V For voltages above 2 0V no change will occur in the output This pin is not available on the LM2905 LM3905 In noisy environments or in comparator-type applications a bypass capacitor on the VADJ terminal may be needed to eliminate spurious outputs because it is high impedance point The size of the cap will depend on the frequency and energy content of the noise A 0 1 mF will generally suffice for spike suppression but several mF may be used if the timer is subjected to high level 60 Hz EMI The emitter and the collector outputs of the timer can be treated just as if they were an ordinary transistor with 40V minimum collector-emitter breakdown voltage Normally the emitter is tied to the ground pin and the signal is taken from the collector or the collector is tied to V a and the signal is taken from the emitter Variations on these basic connections are possible The collector can be tied to any positive voltage up to 40V when the signal is taken from the emitter However the emitter will not be pulled higher than the supply voltage on the V a pin Connecting the collector to a voltage less than the V a voltage is allowed The emitter should not be connected to a low impedance load other than that to which the ground pin is tied The transistor has built-in current limiting with a typical knee current of 120 mA Temporary short circuits are allowed even with collectoremitter voltages up to 40V The power x time product however must not exceed 15 watt-seconds for power levels above the maximum rating of the package A short to 30V 6 Pin Function Description (Continued) for instance cannot be held for more than 4 seconds These levels are based on 40 C maximum initial chip temperature When driving inductive loads always use a clamp diode to protect the transistor from inductive kick-back A boost pin is provided on the LM122 to increase the speed of the internal comparator The comparator is normally operated at low current levels for lowest possible input current For timing periods less than 1 ms where low input current is not needed comparator operating current can be increased several orders of magnitude Shorting the boost terminal to V a increases the emitter current of the vertical PNP drivers in the differential stage from 25 nA to 5 mA This pin is not available on the LM3905 With the timer in the unboosted state timing periods are accurate down to about 1 ms In the boosted mode loss of accuracy due to comparator speed is only about 800 ns so timing periods of several microseconds can be used The 800 ns error is relatively insensitive to temperature so temperature coefficient of pulse width is still good The Logic pin is used to reverse the signal appearing at the output transistor An open or ‘‘high’’ condition on the logic pin programs the output transistor to be ‘‘off’’ during the timing period and ‘‘on’’ all other times Grounding the logic pin reverses the sequence to make the transistor ‘‘on’’ during the timing period Threshold for the logic pin is typically 100 mV with 150 mA flowing out of the terminal If an active drive to the logic pin is desired a saturated transistor drive is recommended either with a discrete transistor or the open collector output of integrated logic A maximum VSAT of 25 mV at 200 mA is required Minimum and maximum voltages that may appear on the logic pin are 0 and a 5 0 respectively TL H 7768 – 11 FIGURE 1 Basic Timer-Collector Output and Timing Chart TL H 7768 – 12 FIGURE 2 Basic Timer-Emitter Output and Timing Chart Typical Applications Basic Timers Figure 1 is a basic timer using the collector output Rt and Ct set the time interval with RL as the load During the timing interval the output may be either high or low depending on the connection of the logic pin Timing waveforms are shown in the sketch along side Figure 1 Note that the trigger pulse may be either shorter or longer than the output pulse width Figure 2 is again a basic timer but with the output taken from the emitter of the output transistor As with the collector output either a high or low condition may be obtained during the timing period Simulating a Thermal Delay Relay Figure 3 is an application where the LM122 is used to simulate a thermal delay relay which prevents power from being applied to other circuitry until the supply has been on for some time The relay remains de-energized for Rt Ct seconds after VCC is applied then closes and stays energized until VCC is turned off Figure 4 is a similar circuit except that the relay is energized as soon as VCC is applied Rt Ct seconds later the relay is de-energized and stays off until the VCC supply is recycled TL H 7768 – 13 FIGURE 3 Time Out on Power Up (Relay Energized Rt Ct Seconds after VCC is Applied) a 5V Supply Driving 28V Relay Figure 5 shows the timer interfacing 5V logic to a high voltage relay Although the V a terminal could be tied to the a 28V supply this may be an unnecessary waste of power in the IC or require extra wiring if the LM122 is on a logic card In either case the threshold for the trigger is 1 6V 7 Typical Applications (Continued) mined by the time required to discharge Ct through the internal discharge transistor A conservative value for Cf can be chosen from the graph included with Figure 20 For frequencies below 1 kHz the frequency error introduced by Cf is a few tenths of one percent or less for Rt t 500k See Chart TL H 7768–14 FIGURE 4 Time Out on Power Up (Relay Energized Until Rt Ct Seconds After VCC is Applied) TL H 7768 – 17 TL H 7768–15 FIGURE 5 5V Logic Supply Driving 28V Relay 30V Supply Interfacing with 5V Logic Figure 6 indicates the ability of the timer to interface to digital logic when operating off a high supply voltage VOUT swings between a 5V and ground with a minimum fanout of 5 for medium speed TTL If the logic is sensitive to rise fall time of the trailing edge of the output pulse the trigger pin should be low at that time TL H 7768 – 18 FIGURE 7 Oscillator One Hour Timer with Reset and Manual Cycle End Figure 8 shows the LM122 connected as a one hour timer with manual controls for start reset and cycle end S1 starts timing but has no effect after timing has started S2 is a center off switch which can either end the cycle prematurely with the appropriate change in output state and discharging of Ct or cause Ct to be reset to 0V without a change in output In the latter case a new timing period starts as soon as S2 is released TL H 7768–16 FIGURE 6 30V Supply Interfacing with 5V Logic Astable Operation The LM122 can be made into a self-starting oscillator by feeding the output back to the trigger input through a capacitor as shown in Figure 7 Operating frequency is 1 (Rt a R1)(Ct) The output is a narrow negative pulse whose width is approximately 2R2 Cf For optimum frequency stability Cf should be as small as possible The minimum value is deter8 Dearborn Electronics LP9A1A476K Polycarbonate TL H 7768 – 19 FIGURE 8 One Hour Timer with Reset and Manual Cycle End Typical Applications (Continued) The average charging current through Rt is about 30 nA so some attention must be paid to parts layout to prevent stray leakage paths The suggested timing capacitor has a typical self time constant of 300 hours and a guaranteed minimum of 25 hours at a 25 C Other capacitor types may be used if sufficient data is available on their leakage characteristics Two Terminal Time Delay Switch The LM122 can be used as a two terminal time delay switch if an ‘‘on’’ voltage drop of 2V to 3V can be tolerated In Figure 9 the timer is used to drive a relay ‘‘on’’ Rt  Ct seconds after application of power ‘‘Off’’ current of the switch is 4 mA maximum and ‘‘on’’ current can be as high as 50 mA Zero Power Dissipation Between Timing Intervals In some applications it is desirable to reduce supply current drain to zero between timing cycles In Figure 10 this is accomplished by using an external PNP as a latch to drive the V a pin of the timer Between timing periods Q1 is off and no supply current is drawn When a trigger pulse of 5V minimum amplitude is received the LM122 output transistor and Q1 latch for the duration of the timing period D1 prevents the step on the V a pin from coupling back into the trigger pin If the trigger input is a short pulse C1 and R2 may be eliminated RL must have a minimum value of (VCC) (2 5 mA) TL H 7768 – 21 FIGURE 10 Zero Power Dissipation Between Timing Intervals TL H 7768 – 22 TL H 7768 – 20 FIGURE 11 Frequency to Voltage Converter (Tachometer) Output Independent of Supply Voltage FIGURE 9 2-Terminal Time Delay Switch Frequency to Voltage Converter An accurate frequency to voltage converter can be made with the LM122 by averaging output pulses with a simple one pole filter as shown in Figure 11 Pulse width is adjusted with R2 to provide initial calibration at 10 kHz The collector of the output transistor is tied to VREF giving constant amplitude pulses equal to VREF at the emitter output R4 and C1 filter the pulses to give a dc output equal to (Rt)(Ct)(VREF)(f) Linearity is about 0 2% for a 0V to 1V output If better linearity is desired R5 can be tied to the summing node of an op amp which has the filter in the feedback path If a low output impedance is desired a unity gain buffer such as the LM110 can be tied to the output An analog meter can be driven directly by placing it in series with R5 to ground A series RC network across the meter to provide damping will improve response at very low frequencies Pulse Width Detector By driving the logic terminal of the LM122 simultaneous to the trigger input a simple accurate pulse width detector can be made (Figure 12) TL H 7768 – 23 VOUT e 0 for W R1 C1 Pulse Out e W b R1 C1 for W R1 C1 FIGURE 12 Pulse Width Detector 9 Typical Applications (Continued) In this application the logic terminal is normally held high by R3 When a trigger pulse is received Q1 is turned on driving the logic terminal to ground The result of triggering the timer and reversing the logic at the same time is that the output does not change from its initial low condition The only time the output will change states is when the trigger input stays high longer than one time period set by Rt and Ct The output pulse width is equal to the input trigger width minus Rt  Ct C2 insures no output pulse for short (kRC) trigger pulses by prematurely resetting the timing capacitor when the trigger pulse drops CL filters the narrow spikes which would occur at the output due to propagation delays during switching 5V Switching Regulator Figure 13 is an application where the LM122 does not use its timing function A switching regulator is made using the internal reference and comparator to drive a PNP transistor switch Features of this circuit include a 5 5V minimum input voltage at 1A output current low part count and good efficiency (l 75%) for input voltages to 10V Line and load regulation are less than 0 5% and output ripple at the switching frequency is only 30 mV Q1 is an inexpensive plastic device which does not need a heatsink for ambient temperature up to 50 C D1 should be a fast switching diode Output voltage can be adjusted between 1V and 30V by choosing proper values for R2 R3 R4 and R5 For outputs less than 2V a divider with 250X Thevinin resistance must be connected between VREF and ground with its tap point tied to VADJ Grounding VADJ will end the timing cycle just as if the timing capacitor had reached its normal discharge point A new timing cycle can be started by the trigger terminal as soon as the ground is released A switching transistor is best for driving VADJ to as near ground as possible Worst case sink current is about 300 mA A timing cycle may also be ended by a positive pulse to a resistor (R s Rt 100) in series with the timing capacitor The pulse amplitude must be at least equal to VADJ (2 0V) but should not exceed 5 0V When the timing capacitor discharges a negative spike of up to 2 0V will occur across the resistor so some caution must be used if the drive pulse is used for other circuitry TL H 7768 – 25 FIGURE 14 Cycle Interrupt The output of the timer can be wire ORed with a discrete transistor or an open collector logic gate output This allows overriding of the timer output but does not cause the timer to be reset until its normal cycle time has elapsed Using the LM122 as a Comparator A built-in reference and zero volt common mode limit make the LM122 very useful as a comparator Threshold may be adjusted from zero to three volts by driving the VADJ terminal with a divider tied to VREF Stability of the reference voltage is typically g 1% over a temperature range of b 55 C to a 125 C Offset voltage drift in the comparator is typically 25 mV C in the boosted mode and 50 mV C unboosted A resistor can be inserted in series with the input to allow overdrives up to g 50V as shown in Figure 15 There is actually no limit on input voltage as long as current is limited to g 1 mA The resistor shown contributes a worst case of 5 mV to initial offset In the unboosted mode the error drops to 0 25 mV maximum The capability of operating off a single 5V supply with internal reference should make this comparator very useful No 22 Wire Wound on Molybdenum Permalloy Core TL H 7768–24 FIGURE 13 5V Switching Regulator with 1 Amp Output and 5 5V Minimum Input Application Hints Aborting a Timing Cycle The LM122 does not have an input specifically allocated to a stop-timing function If such a function is desired it may be accomplished several ways  Ground VADJ  Raise R C more positive than VADJ  Wire ‘‘OR’’ the output 10 Application Hints (Continued) ‘‘high’’ is 2 5V R2 may be calculated from the divider equation with R1 to give these levels Timer Protected Against Damage for up to 50V TL H 7768 – 26 FIGURE 15 Comparator with 0V to 3V Threshold Eliminating Timing Cycle Upon Initial Application of Power The LM122 will normally start a timing cycle (with no trigger input) when V a is first turned on If this characteristic is undesirable it can be defeated by tying the timing capacitor to VREF instead of ground as shown in Figure 16 This connection does not affect operation of the timer in any other way If an electrolytic timing capacitor is used be sure the negative end is tied to the R C pin and the positive end to VREF A 1 0 kX resistor should be included in series with the timing capacitor to limit the surge current load on VREF when the capacitor is discharged TL H 7768 – 28 Select for Proper Level Shift Emitter Terminal or Emitter Load must be Tied to GND Pin of Timer FIGURE 17 Operating Off Dual Supplies Linearizing the Charging Sweep In some applications (such as a linear pulse width modulator) it may be desirable to have the timing capacitor charge from a constant current source A simple way to accomplish this is shown in Figure 18 TL H 7768 – 27 FIGURE 16 Eliminating Initial Timing Cycle Using Dual Supplies The LM122 can be operated off dual supplies as shown in Figure 17 The only limitation is that the emitter terminal cannot be tied to ground it must either drive a load referred to Vb or be actually tied to Vb as shown Although capacitive coupling is shown for the trigger input (to allow 5V triggering) a resistor can be substituted for C1 R2 must be chosen to give proper level shifting between the trigger signal and the trigger pin of the timer Worst case ‘‘lo’’ on the trigger pin (with respect to Vb) is 0 8V and worst case TL H 7768 – 29 FIGURE 18 Temperature Compensated Linear Charging Sweep Q1 converts the current through R1 to a current source independent of the voltage across Ct R2 R3 D1 and D2 are added to make the current through R1 independent of supply variations and temperature changes (D2 is a low TC type) D2 and R3 can be omitted if the V a supply is stable and D1 and R2 can be omitted also if temperature stability is not critical With D1 D2 R2 and R3 omitted the current through R1 will change about 0 015% C with a 15V supply and 0 1% C with a 5 0V supply 11 Application Hints (Continued) Triggering with Negative Edge Although the LM122 is triggered by a positive going trigger signal a differentiator tied to a normally ‘‘high’’ trigger will result in negative edge triggering In Figure 19 R1 serves the dual purpose of holding the trigger pin normally high and differentiating the input trigger pulse coupled through C1 The timing diagram included with Figure 21 shows that triggering actually occurs a short time after the negative going trigger while positive going triggers have no effect The delay time between a negative trigger signal and actual starts of timing is approximately (0 5 to 1 5) (R1  C1) depending on the trigger amplitude or about 2 5 to 7 5 ms with the values shown This time will have to be increased for Ct larger than 0 01 mF because Ct is charged to VREF whenever the trigger pin is kept high and must reset itself during the short time that the trigger pin voltage is low A conservative value for C1 is C1 t Ct 10 TL H 7768 – 30 Chain of Timers The LM122 can be connected as a chain of timers quite easily with no interface required In Figure 20A and 20B two FIGURE 19 Timer Triggered by Negative Edge of Input Pulse possible connections are shown In both cases the output of the timer is low during the timing period so that the positive going signal at the end of the timing period can trigger the next timer There is no limitation on the timing period of one timer with respect to any other timer before or after it because the trigger input to any timer can be high or low when that timer ends its timing period TL H 7768 – 31 (a) TL H 7768 – 32 TL H 7768 – 33 (b) FIGURE 20 Chain of Timers 12 Physical Dimensions inches (millimeters) Metal Can Package (H) Order Number LM122H NS Package Number H10C Dual-In-Line Package (N) Order Number LM322N NS Package Number N14A 13 LM122 LM322 LM3905 Precision Timers Physical Dimensions inches (millimeters) (Continued) Dual-In-Line Package (N) Order Number LM3905N NS Package Number N08E LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION As used herein 1 Life support devices or systems are devices or systems which (a) are intended for surgical implant into the body or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user National Semiconductor Corporation 1111 West Bardin Road Arlington TX 76017 Tel 1(800) 272-9959 Fax 1(800) 737-7018 2 A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness National Semiconductor Europe Fax (a49) 0-180-530 85 86 Email cnjwge tevm2 nsc com Deutsch Tel (a49) 0-180-530 85 85 English Tel (a49) 0-180-532 78 32 Fran ais Tel (a49) 0-180-532 93 58 Italiano Tel (a49) 0-180-534 16 80 National Semiconductor Hong Kong Ltd 13th Floor Straight Block Ocean Centre 5 Canton Rd Tsimshatsui Kowloon Hong Kong Tel (852) 2737-1600 Fax (852) 2736-9960 National Semiconductor Japan Ltd Tel 81-043-299-2309 Fax 81-043-299-2408 National does not assume any responsibility for use of any circuitry described no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications