LM140JAN Three Terminal Positive Regulators
February 2006
LM140JAN Three Terminal Positive Regulators
General Description
The monolithic 3-terminal positive voltage regulators employ internal current-limiting, thermal shutdown and safe-area compensation, making them essentially indestructible. If adequate heat sinking is provided, they can deliver over 0.5A and 1.0A output current. They are intended as fixed voltage regulators in a wide range of applications including local (on-card) regulation for elimination of noise and distribution problems associated with single-point regulation. In addition to use as fixed voltage regulators, these devices can be used with external components to obtain adjustable output voltages and currents. Considerable effort was expended to make the entire series of regulators easy to use and minimize the number of external components. It is not necessary to bypass the output, although this does improve transient response. Input bypassing is needed only if the regulator is located far from the filter capacitor of the power supply.
Features
n n n n n Complete specifications at 0.5A and 1.0A loads No external components Internal thermal overload protection Internal short circuit current-limiting Output transistor safe-area compensation
Ordering Information
NS Part Number JL140-5BXA JL140-5BYA JL140-5SXA JL140-5SYA JL140-12BXA JL140-12BYA JL140-12SXA JL140-15BXA JL140-15BYA JL140-15SYA SMD Part Number JM38510/10702BXA JM38510/10706BYA JM38510/10702SXA JM38510/10706SYA JM38510/10703BXA JM38510/10707BYA JM38510/10703SXA JM38510/10704BXA JM38510/10708BYA JM38510/10708SYA NS Package Number H03A K02C H03A K02C H03A K02C H03A H03A K02C K02C Package Description 3LD TO-39 Metal Can 2LD TO-3 Metal Can 3LD TO-39 Metal Can 2LD TO-3 Metal Can 3LD TO-39 Metal Can 2LD TO-3 Metal Can 3LD TO-39 Metal Can 3LD TO-39 Metal Can 2LD TO-3 Metal Can 2LD TO-3 Metal Can
Connection Diagrams
Steel Metal Can TO-39 Package (H) TO-3 Metal Can (K)
20164602 20164601
Bottom View See NS Package Number H03A
Bottom View See NS Package Number K02C
© 2006 National Semiconductor Corporation
DS201646
www.national.com
LM140JAN
Absolute Maximum Ratings (Note 1)
DC Input Voltage Internal Power Dissipation (Note 2) Maximum Junction Temperature (TJmax) Storage Temperature Range Operating Temperature Range Lead Temperature (Soldering 10 seconds) Thermal Resistance θJA T0−5 (Still Air) T0−5 (500 LF/Min Air Flow) T0−3 (Still Air) T0−3 (500 LF/Min Air Flow) θJC T0−5 T0−3 ESD Susceptibility (Note 3) 15˚C/W 4˚C/W 2KV 232˚C/W 77˚C/W 35˚C/W TBD 35V Internally Limited 150˚C -65˚C ≤ TA ≤ +150˚C -55˚C ≤ TA ≤ +125˚C 300˚C
Quality Conformance Inspection
MIL-Std-883, Method 5005 - Group A Subgroup 1 2 3 4 5 6 7 8A 8B 9 10 11 12 13 14 Description Static tests at Static tests at Static tests at Dynamic tests at Dynamic tests at Dynamic tests at Functional tests at Functional tests at Functional tests at Switching tests at Switching tests at Switching tests at Settling time at Settling time at Settling time at Temp ˚C 25 125 -55 25 125 -55 25 125 -55 25 125 -55 25 125 -55
www.national.com
2
LM140JAN
LM140H-5.0 (JL140-5BXA, SXA) JAN Electrical Characteristics DC Parameters
Symbol VO (1) Parameter Output Voltage Conditions VI = 8V, IL = -5mA VI = 8V, IL = -500mA VI = 20V, IL = -5mA VI = 20V, IL = -500mA VI = 35V, IL = -5mA VI = 35V, IL = -50mA VRLine VRLoad ISCD ∆ISCD Line IOL IOS Line Regulation Load Regulation Stand by Current Drain Stand by IDrain vs. VLine Overload Current Output Short Circuit Current 8V ≤ VI ≤ 35V, IL = -50mA 8V ≤ VI ≤ 25V, IL = -350mA VI = 10V, -500mA ≤ IL ≤ -5mA VI = 35V, -50mA ≤ IL ≤ -5mA VI = 10V, IL = -5mA VI = 35V, IL = -5mA 8V ≤ VI ≤ 35V, IL = -5mA VI = 10V, -500mA ≤ IL ≤ -5mA VI = 8V, Forced ∆VO = -0.48V VI = 10V VI = 25V VI = 35V VO (2) VO (3) ∆VO / ∆T Output Voltage Output Voltage Average Temperature Coefficient of Output Voltage VI = 10V, IL = -5mA VI = 10V, IL = -5mA VI = 10V, IL = -5mA, 25˚C ≤ TA ≤ 125˚C VI = 10V, IL = -5mA, -55˚C ≤ TA ≤ 25˚C (Note 4) (Note 5) (Note 6) (Note 6) ∆ISCD Load Stand by IDrain vs. ILoad Notes Min 4.75 4.75 4.75 4.75 4.75 4.75 -150 -50 -100 -150 -7.0 -8.0 -1.0 -0.5 -2.0 -2.0 -1.5 -1.0 4.7 4.75 -2.0 -2.0 Max 5.25 5.25 5.25 5.25 5.25 5.25 150 50 100 150 -0.5 -0.5 1.0 0.5 -0.5 -0.01 -0.01 -0.01 5.3 5.25 2.0 2.0 Unit V V V V V V mV mV mV mV mA mA mA mA A A A A V V mV/˚C mV/˚C Subgroups 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 2 7, 8A, 8B 8A 8B
AC Parameters
Symbol NO ∆VO / ∆VI ∆VO / ∆IL ∆VI / ∆VO Parameter Output Noise Voltage Transient Line Response Transient Load Response Ripple Rejection Conditions VI = 10V, IL = -50mA VI = 10V, IL = -5mA, VPulse = 3V VI = 10V, ∆IL = -200mA, IL = -50mA VI = 10V, IL = -125mA, eI = 1VRMS at ƒ = 2400Hz, 60 Notes Min Max 125 30 2.5 Unit µVRMS mV/V mV/mA dB Subgroups 7 7 7 4
DC Drift Parameters
Delta calculations performed on JAN S devices at group B, Subgroup 5, only. Symbol VO Parameter Output Voltage Conditions VI = 8V, IL = -5mA VI = 8V, IL = -500mA VI = 20V, IL = -5mA VI = 20V, IL = -500mA VI = 35V, IL = -5mA VI = 35V, IL = -50mA ISCD Stand by Current Drain VI = 10V, IL = -5mA
3
Notes
Min
Max
Unit V V V V V V %
Subgroups 1 1 1 1 1 1 1
www.national.com
-0.025 0.025 -0.025 0.025 -0.025 0.025 -0.025 0.025 -0.025 0.025 -0.025 0.025 -20 20
LM140JAN
LM140H-12 (JL140-12BXA, SXA) JAN Electrical Characteristics DC Parameters
Symbol VO (1) Parameter Output Voltage Conditions VI = 15V, IL = -5mA VI = 15V, IL = -0.5A VI = 27V, IL = -5mA VI = 27V, IL = -0.5A VI = 35V, IL = -5mA VI = 35V, IL = -50mA VRLine VRLoad ISCD ∆ISCD Line IOL IOS Line Regulation Load Regulation Stand by Current Drain Stand by IDrain vs. VLine Over Load Current Output Short Circuit Current 15V ≤ VI ≤ 35V, IL = -50mA 15V ≤ VI ≤ 32V, IL = -350mA VI = 17V, -500mA ≤ IL ≤ -5mA VI = 35V, -50mA ≤ IL ≤ -5mA VI = 17V, IL = -5mA VI = 35V, IL = -5mA 15V ≤ VI ≤ 35V, IL = -5mA VI = 17V, -500mA ≤ IL ≤ -5mA VI = 15V, ∆VO = -1.13V VI = 17V VI = 32V VI = 35V VO (2) VO (3) ∆VO / ∆T Output Voltage Output Voltage Average Temperature Coefficient Output Voltage VI = 17V, IL = -5mA VI = 17V, IL = -5mA 25˚C ≤ TA ≤ +125˚C, VI = 17V, IL = -5mA -55˚C ≤ TA ≤ 25˚C, VI = 17V, IL = -5mA (Note 4) (Note 5) (Note 7) (Note 7) ∆ISCD Load Stand by IDrain vs. ILoad Notes Min 11.4 11.4 11.4 11.4 11.4 11.4 -360 -120 -240 -360 -7.0 -8.0 -1.0 -0.5 -2.0 Max 12.6 12.6 12.6 12.6 12.6 12.6 360 120 240 360 -0.5 -0.5 1.0 0.5 -0.5 Unit V V V V V V mV mV mV mV mA mA mA mA A A A A V V mV/˚C mV/˚C Subgroups 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 2 7, 8A, 8B 8A 8B
-1.75 -0.01 -1.25 -0.01 -1.00 -0.01 11.28 12.72 11.4 -3.0 -3.0 12.6 3.0 3.0
AC Parameters
Symbol NO ∆VO / ∆IL ∆VO / ∆VI ∆VI / ∆VO Parameter Output Noise Voltage Transient Load Response Transient Line Response Ripple Rejection Conditions VI = 17V, IL = -50mA VI = 17V, IL = -50mA, ∆IL = -200mA VI = 17V, VPulse = 3V, IL = -5mA VI = 17V, IL = -125mA, eI = 1VRMS at ƒ = 2400Hz 55 Notes Min Max 250 2.5 30 Unit µVRMS mV/mA mV/V dB Subgroups 7 7 7 4
DC Drift Parameters
Delta calculations performed on JAN S devices at group B, Subgroup 5, only. Symbol VO Parameter Output Voltage Conditions VI = 15V, IL = -5mA VI = 15V, IL = -0.5A VI = 27V, IL = -5mA VI = 27V, IL = -0.5A VI = 35V, IL = -5mA VI = 35V, IL = -50mA ISCD Stand by Current Drain VI = 17V, IL = -5mA
4
Notes
Min -0.06 -0.06 -0.06 -0.06 -0.06 -0.06 -20
Max 0.06 0.06 0.06 0.06 0.06 0.06 20
Unit V V V V V V %
Subgroups 1 1 1 1 1 1 1
www.national.com
LM140JAN
LM140H-15 (JL140-15BXA) JAN Electrical Characteristics DC Parameters
Symbol VO (1) Parameter Output Voltage Conditions VI = 18.5V, IL = -5mA VI = 18.5V, IL = -500mA VI = 30V, IL = -5mA VI = 30V, IL = -500mA VI = 35V, IL = -5mA VI = 35V, IL = -50mA VRLine VRLOAD ISCD ∆ISCD Line IOL IOS VO (2) VO (3) ∆VO / ∆T Line Regulation Load Regulation Stand by Current Drain Stand by IDrain vs. VLine Overload Current Output Short Circuit Current Output Short Circuit Current Output Voltage Output Voltage Average Temperature Coefficient Output Voltage Average Temperature Coefficient Output Voltage 18.5V ≤ VI ≤ 35V, IL = -350mA -500mA ≤ IL ≤ -5mA, VI = 20V -50mA ≤ IL ≤ -5mA, VI = 35V VI = 20V, IL = -5mA VI = 35V, IL = -5mA 18.5V ≤ VI ≤ 35V, IL = -5mA -500mA ≤ IL ≤ -5mA, VI = 20V Forced ∆VO = -1.43V, VI = 18.5V VI = 20V VI = 35V VI = 20V, IL = -5mA VI = 20V, IL = -5mA 25˚C ≤ TA ≤ +125˚C, VI = 20V, IL = -5mA -55˚C ≤ TA ≤ 25˚C, VI = 20V, IL = -5mA (Note 4) (Note 5) (Note 7) (Note 7) ∆ISCD Load Stand by IDrain vs. ILoad Notes Min Max Unit V V V V V V mV mV mV mA mA mA mA A A A V V mV/˚C mV/˚C Subgroups 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 2 7, 8A, 8B 8A 8B
14.25 15.75 14.25 15.75 14.25 15.75 14.25 15.75 14.25 15.75 14.25 15.75 -150 -300 -450 -7.0 -8.0 -1.0 -0.5 -2.0 150 300 450 -0.5 -0.5 1.0 0.5 -0.5
-1.75 -0.01 -1.0 14.1 -3.75 -3.75 -0.01 15.9 3.75 3.75
14.25 15.75
AC Parameters
Symbol NO ∆VO / ∆IL ∆VO / ∆VI ∆VI / ∆VO Parameter Output Noise Voltage Transient Load Response Transient Line Response Ripple Rejection Conditions VI = 20V, IL = -50mA ∆IL = -200mA, VI = 20V, IL = -50mA VI = 20V, IL = -5mA, VPulse = 3V VI = 20V, IL = -125mA, eI = 1VRMS at ƒ = 2400Hz 53 Notes Min Max 300 2.5 30 Unit µVRMS mV/mA mV/V dB Subgroups 7 7 7 4
DC Drift Parameters
Delta calculations performed on JAN S devices at group B, Subgroup 5, only. Symbol VO Parameter Output Voltage Conditions VI = 18.5V, IL = -5mA VI = 18.5V, IL = -500mA VI = 30V, IL = -5mA VI = 30V, IL = -500mA VI = 35V, IL = -5mA VI = 35V, IL = -50mA ISCD Stand by Current Drain VI = 20V, IL = -5mA Notes Min Max Unit V V V V V V % Subgroups 1 1 1 1 1 1 1
-0.075 0.075 -0.075 0.075 -0.075 0.075 -0.075 0.075 -0.075 0.075 -0.075 0.075 -20 20
5
www.national.com
LM140JAN
LM140K-5.0 (JL140-5BYA, SYA) JAN Electrical Characteristics DC Parameters
Symbol VO (1) Parameter Output Voltage Conditions VI = 8V, IL = -5mA VI = 8V, IL = -1A VI = 20V, IL = -5mA VI = 20V, IL = -1A VI = 35V, IL = -5mA VI = 35V, IL = -0.1A VRLine VRLoad ISCD ∆ISCD Line IOL IOS Line Regulation Load Regulation Stand by Current Drain Stand by IDrain vs. VLine Overload Current Output Short Circuit Current 8V ≤ VI ≤ 35V, IL = -0.1A 8V ≤ VI ≤ 25V, IL = -0.5A VI = 10V, -1A ≤ IL ≤ -5mA VI = 35V, -0.1A ≤ IL ≤ -5mA VI = 10V, IL = -5mA VI = 35V, IL = -5mA 8V ≤ VI ≤ 35V, IL = -5mA VI = 10V, -1A ≤ IL ≤ -5mA VI = 8V, Forced ∆VO = -0.48V VI = 10V VI = 25V VI = 35V VO (2) VO (3) ∆VO / ∆T Output Voltage Output Voltage Average Temperature Coefficient Output Voltage VI = 10V, IL = -5mA VI = 10V, IL = -5mA VI = 10V, IL = -5mA, 25˚C ≤ TA ≤ 125˚C VI = 10V, IL = -5mA, -55˚C ≤ TA ≤ 25˚C (Note 4) (Note 5) (Note 6) (Note 6) ∆ISCD Load Stand by IDrain vs. ILoad Notes Min 4.75 4.75 4.75 4.75 4.75 4.75 -150 -50 -100 -150 -7.0 -8.0 -1.0 -0.5 -4.0 -4.0 -3.0 -2.0 4.7 4.75 -2.0 -2.0 Max 5.25 5.25 5.25 5.25 5.25 5.25 150 50 100 150 -0.5 -0.5 1.0 0.5 -1.0 -0.02 -0.02 -0.02 5.3 5.25 2.0 2.0 Unit V V V V V V mV mV mV mV mA mA mA mA A A A A V V mV/˚C mV/˚C Subgroups 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 2 7, 8A, 8B 8A 8B
AC Parameters
Symbol NO ∆VO /∆ VI ∆VO /∆ IL ∆VI /∆ VO Parameter Output Noise Voltage Transient Line Response Transient Load Response Ripple Rejection Conditions VI = 10V, IL = -0.1A VI = 10V, VPulse = 3V, IL = -5mA VI = 10V, ∆IL = -400mA, IL = -100mA VI = 10V, IL = -350mA, eI = 1VRMS at ƒ = 2400Hz 60 Notes Min Max 125 30 2.5 Unit µVRMS mV/V mV/mA dB Subgroups 7 7 7 4
DC Drift Parameters
Delta calculations performed on JAN S devices at group B, Subgroup 5, only. Symbol VO Parameter Output Voltage Conditions VI = 8V, IL = -5mA VI = 8V, IL = -1A VI = 20V, IL = -5mA VI = 20V, IL = -1A VI = 35V, IL = -5mA VI = 35V, IL = -0.1A ISCD Stand by Current Drain VI = 10V, IL = -5mA
6
Notes
Min
Max
Unit V V V V V V %
Subgroups 1 1 1 1 1 1 1
-0.025 0.025 -0.025 0.025 -0.025 0.025 -0.025 0.025 -0.025 0.025 -0.025 0.025 -20 20
www.national.com
LM140JAN
LM140K-12 (JL140-12BYA) JAN Electrical Characteristics DC Parameters
Symbol VO (1) Parameter Output Voltage Conditions VI = 15V, IL = -5mA VI = 15V, IL = -1A VI = 27V, IL = -5mA VI = 27V, IL = -1A VI = 35V, IL = -5mA VI = 35V, IL = -0.1A VRLine VRLoad ISCD Line Regulation Load Regulation Stand by Current Drain 15V ≤ VI ≤ 35V, IL = -0.1A 15V ≤ VI ≤ 32V, IL = -0.5A VI = 17V, -1A ≤ IL ≤ -5mA VI = 35V, -0.1A ≤ IL ≤ -5mA VI = 17V, IL = -5mA VI = 35V, IL = -5mA ∆ISCD Line Stand by IDrain vs. VLine ∆ISCD Load Stand by IDrain vs. ILoad IOL IOS Over Load Current Output Short Circuit Current 15V ≤ VI ≤ 35V, IL = -5mA VI = 17V, -1A ≤ IL ≤ -5mA Forced ∆VO = -1.13V, VI = 15V VI = 17V VI = 32V VI = 35V VO (2) VO (3) ∆VO / ∆T Output Voltage Output Voltage Average Temperature Coefficient Output Voltage VI = 17V, IL = -5mA VI = 17V, IL = -5mA 25˚C ≤ TA ≤ +125˚C, VI = 17V, IL = -5mA -55˚C ≤ TA ≤ 25˚C, VI = 17V, IL = -5mA (Note 4) (Note 5) (Note 7) (Note 7) Notes Min 11.4 11.4 11.4 11.4 11.4 11.4 -360 -120 -240 -360 -7.0 -8.0 -1.0 -0.5 -4.0 -3.5 -2.5 -2.0 11.4 -3.0 -3.0 Max 12.6 12.6 12.6 12.6 12.6 12.6 360 120 240 360 -0.5 -0.5 1.0 0.5 -1.0 -0.02 -0.02 -0.02 12.6 3.0 3.0 Unit V V V V V V mV mV mV mV mA mA mA mA A A A A V V mV/˚C mV/˚C Subgroups 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 2 7, 8A, 8B 8A 8B
11.28 12.72
AC Parameters
Symbol NO ∆VO / ∆IL ∆VO / ∆VI ∆VI / ∆VO Parameter Output Noise Voltage Transient Load Response Transient Line Response Ripple Rejection Conditions VI = 17V, IL = -0.1A VI = 17V, IL = -100mA, ∆IL = -400mA VI = 17V, VPulse = 3V, IL = -5mA VI = 17V, eI = 1VRMS at ƒ = 2400Hz, IL = -350mA 55 Notes Min Max 250 2.5 30 Unit µVRMS mV/mA mV/V dB Sup groups 7 7 7 4
DC Drift Parameters
Delta calculations performed on JAN S devices at group B, Subgroup 5, only. Symbol VO Parameter Output Voltage Conditions VI = 15V, IL = -5mA VI = 15V, IL = -1A VI = 27V, IL = -5mA VI = 27V, IL = -1A VI = 35V, IL = -5mA VI = 35V, IL = -0.1A ISCD Stand by Current Drain VI = 17V, IL = -5mA
7
Notes
Min -0.06 -0.06 -0.06 -0.06 -0.06 -0.06 -20
Max 0.06 0.06 0.06 0.06 0.06 0.06 20
Unit V V V V V V %
Subgroups 1 1 1 1 1 1 1
www.national.com
LM140JAN
LM140K-15 (JL140-15BYA, SYA) JAN Electrical Characteristics DC Parameters
Symbol VO (1) Parameter Output Voltage Conditions VI = 18.5V, IL = -5mA VI = 18.5V, IL = -1A VI = 30V, IL = -5mA VI = 30V, IL = -1A VI = 35V, IL = -5mA VI = 35V, IL = -0.1A VRLine VRLoad ISCD ∆ISCD Line IOL IOS VO (2) VO (3) ∆VO / ∆T Line Regulation Load Regulation Stand by Current Drain Stand by IDrain vs. VLine Overload Current Output Short Circuit Current Output Voltage Output Voltage Average Temperature Coefficient Output Voltage 18.5V ≤ VI ≤ 35V, IL = -0.5A VI = 20V, -1A ≤ IL ≤ -5mA VI = 35V, -0.1A ≤ IL ≤ -5mA VI = 20V, IL = -5mA VI = 35V, IL = -5mA 18.5V ≤ VI ≤ 35V, IL = -5mA VI = 20V, -1A ≤ IL ≤ -5mA Forced ∆VO = -1.43V, VI = 18.5V VI = 20V VI = 35V VI = 20V, IL = -5mA VI = 20V, IL = -5mA 25˚C ≤ TA ≤ +125˚C, VI = 20V, IL = -5mA -55˚C ≤ TA ≤ 25˚C, VI = 20V, IL = -5mA (Note 4) (Note 5) (Note 8) (Note 8) ∆ISCD Load Stand by IDrain vs. ILoad Notes Min Max Unit V V V V V V mV mV mV mA mA mA mA A A A V V mV/˚C mV/˚C Subgroups 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 2 7, 8A, 8B 8A 8B
14.25 15.75 14.25 15.75 14.25 15.75 14.25 15.75 14.25 15.75 14.25 15.75 -150 -300 -450 -7.0 -8.0 -1.0 -0.5 -4.0 -3.5 -2.0 14.1 -3.75 -3.75 150 300 450 -0.5 -0.5 1.0 0.5 -1.0 -0.02 -0.02 15.9 3.75 3.75
14.25 15.75
AC Parameters
Symbol NO ∆VO / ∆IL ∆VO / ∆VI ∆VI / ∆VO Parameter Output Noise Voltage Transient Load Response Transient Line Response Ripple Rejection Conditions VI = 20V, IL = -0.1A ∆IL = -400mA, VI = 20V, IL = -100mA VI = 20V, VPulse = 3V, IL = -5mA VI = 20V, IL = -350mA, eI = 1VRMS at f = 2400Hz 53 Notes Min Max 300 2.5 30 Unit µVRMS mV/mA mV/V dB Subgroups 7 7 7 4
DC Drift Parameters
Delta calculations performed on JAN S devices at group B, Subgroup 5, only. Symbol VO Parameter Output Voltage Conditions VI = 18.5V, IL = -5mA VI = 18.5V, IL = -1A VI = 30V, IL = -5mA VI = 30V, IL = -1A VI = 35V, IL = -5mA VI = 35V, IL = -0.1A ISCD Stand by Current Drain VI = 20V, IL = -5mA Notes Min Max Unit V V V V V V % Subgroups 1 1 1 1 1 1 1
-0.075 0.075 -0.075 0.075 -0.075 0.075 -0.075 0.075 -0.075 0.075 -0.075 0.075 -20 20
www.national.com
8
LM140JAN
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. Note 2: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJmax (maximum junction temperature), θJA (package junction to ambient thermal resistance), and TA (ambient temperature). The maximum allowable power dissipation at any temperature is PDmax = (TJmax - TA)/θJA or the number given in the Absolute Maximum Ratings, whichever is lower. Note 3: Human body model, 100pF discharged through 1.5KΩ Note 4: Tested at TA = +125˚C, correlated to TA = +150˚C. Note 5: Tested at extremes as a set up for ∆VO/∆T tests. Note 6: Calculated parameter. For calculations use VO @ VI = 10V, IL = −5mA.(Note 5) Note 7: Calculated parameter. For calculations use VO @ VI = 17V, IL = −5mA.(Note 5) Note 8: Calculated parameter. For calculations use VO @ VI = 20V, IL = −5mA.(Note 5)
9
www.national.com
LM140JAN
Revision History
Released 02/07/06 Revision A Section New Release, Corporate format Originator L. Lytle Changes 6 MDS data sheets converted into one Corp. data sheet format. The drift tables were eliminated from the 883 section since it did not apply. MDS data sheets MJLM140-05-H Rev 0B0, MJLM140-05-K Rev. 0B0, MJLM140-12-H Rev 0B0, MJLM140-12-K Rev 0B0, MJLM140-15-H Rev 0B0, and MJLM140-15-K Rev 0B0 will be archived.
www.national.com
10
LM140JAN
Physical Dimensions
inches (millimeters) unless otherwise noted
Metal Can TO-39 (H) NS Package Number H03A
Steel Metal Can Package (K) NS Package Number K02C
11
www.national.com
LM140JAN Three Terminal Positive Regulators
Notes
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2. Leadfree products are RoHS compliant.
National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560
2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.
