LM2436

LM2436 Monolithic Triple 7.5 ns CRT Driver June 2002 LM2436 Monolithic Triple 7.5 ns CRT Driver General Description The LM2436 is an integrated high voltage CRT driver circuit designed for use in color monitor applications. The IC contains three high input impedance, wide band amplifiers which directly drive the RGB cathodes of a CRT. Each channel has its gain internally set to −14 and can drive CRT capacitive loads as well as resistive loads present in other applications, limited only by the package’s power dissipation. The IC is packaged in an industry standard 9-lead TO-220 molded plastic power package. See the Thermal Considerations section for more information. Features n Well matched with LM1279 video preamp n 0V to 5V input range n Stable with 0–20 pF capacitive loads and inductive peaking networks n Convenient TO-220 staggered lead package style n Standard LM243X Family Pinout which is designed for easy PCB layout Applications n 1024 x 768 displays up to 85 Hz refresh n Pixel clock frequencies up to 100 MHz n Monitors using video blanking Schematic Diagram 20043501 FIGURE 1. Simplified Schematic Diagram (One Channel) © 2002 National Semiconductor Corporation DS200435 www.national.com LM2436 Connection Diagram 20043502 Note: Tab is at GND Top View Order Number LM2436TA www.national.com 2 LM2436 Absolute Maximum Ratings 3) (Notes 1, Machine Model 250V If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (VCC) Bias Voltage (VBB) Input Voltage (VIN) Storage Temperature Range (TSTG) Lead Temperature (Soldering, < 10 sec.) ESD Tolerance, Human Body Model 300˚C 2 kV +90V +16V 0V to 6V −65˚C to +150˚C Operating Ranges (Note 2) VCC VBB VIN VOUT Case Temperature +60V to +85V +8V to +15V +0V to +5V +15V to +75V −20˚C to +100˚C Do not operate the part without a heat sink. Electrical Characteristics (See Figure 2 for Test Circuit) Unless otherwise noted: VCC = +80V, VBB = +12V, VIN = +2.7 VDC, CL = 8 pF, Output = 40 VPP at 1 MHz, TC = 50˚C. Symbol ICC IBB VOUT AV ∆A V LE tR tF OS Parameter Supply Current Bias Current DC Output Voltage DC Voltage Gain Gain Matching Linearity Error Rise Time Fall Time Overshoot Conditions All Three Channels, No Input Signal, No Output Load All Three Channels No AC Input Signal, VIN = 1.2V No AC Input Signal (Note 4), No AC Input Signal (Notes 4, 5), No AC Input Signal (Note 6), 10% to 90% (Note 6), 90% to 10% (Note 6) 62 −12 LM2436 Min Typical 30 12 65 −14 1.0 8 7.5 7.5 1 68 −16 dB % ns ns % Max Units mA mA VDC Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Note 2: Operating ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may change when the device is not operated under the listed test conditions. Note 3: All voltages are measured with respect to GND, unless otherwise specified. Note 4: Calculated value from Voltage Gain test on each channel. Note 5: Linearity Error is the variation in dc gain from VIN = 1.0V to VIN = 4.5V. Note 6: Input from signal generator: tr, tf < 1 ns. 3 www.national.com LM2436 AC Test Circuit 20043503 Note: 8 pF load includes parasitic capacitance. FIGURE 2. Test Circuit (One Channel) Figure 2 shows a typical test circuit for evaluation of the LM2436. This circuit is designed to allow testing of the LM2436 in a 50Ω environment without the use of an expensive FET probe. The two 2490Ω resistors form a 200:1 divider with the 50Ω resistor and the oscilloscope. A test point is included for easy use of an oscilloscope probe.The compensation capacitor is used to compensate the stray capacitance of the two 2490Ω resistors to achieve flat frequency response. www.national.com 4 LM2436 Typical Performance Characteristics (25V−65V), Test Circuit - Figure 2 unless otherwise specified) (VCC = +80 VDC, VBB = +12 VDC, CL = 8 pF, VOUT = 40 VPP 20043515 20043516 FIGURE 3. VOUT vs VIN FIGURE 6. Power Dissipation vs Frequency 20043517 20043518 FIGURE 4. Speed vs Temp. FIGURE 7. Speed vs Offset 20043519 20043520 FIGURE 5. LM2436 Pulse Response FIGURE 8. Speed vs Load Capacitance 5 www.national.com LM2436 Theory of Operation The LM2436 is a high voltage monolithic three channel CRT driver suitable for high resolution display applications. The LM2436 operates with 80V and 12V power supplies. The part is housed in the industry standard 9-lead TO-220 molded plastic power package. The circuit diagram of the LM2436 is shown in Figure 1. The PNP emitter follower, Q5, provides input buffering. Q1 and Q2 form a fixed gain cascode amplifier with resistors R1 and R2 setting the gain at −14. Emitter followers Q3 and Q4 isolate the high output impedance of the cascode stage from the capacitance of the CRT cathode which decreases the sensitivity of the device to load capacitance. Q6 provides biasing to the output emitter follower stage to reduce crossover distortion at low signal levels. Figure 2 shows a typical test circuit for evaluation of the LM2436. This circuit is designed to allow testing of the LM2436 in a 50Ω environment without the use of an expensive FET probe. In this test circuit, the two 2.49kΩ resistors form a 200:1 wideband, low capacitance probe when connected to a 50Ω coaxial cable and a 50Ω load (such as a 50Ω oscilloscope input). The input signal from the generator is ac coupled to the base of Q5. protect against damage from CRT arcover are designed specifically for the LM2436. If another member of the 243X family is used, please refer to its datasheet for device specific information. POWER SUPPLY BYPASS Since the LM2436 is a wide bandwidth amplifier, proper power supply bypassing is critical for optimum performance. Improper power supply bypassing can result in large overshoot, ringing or oscillation. 0.1 µF capacitors should be connected from the supply pins, VCC and VBB, to ground, as close to the LM2436 as is practical. Additionally, a 47 µF or larger electrolytic capacitor should be connected from both supply pins to ground reasonably close to the LM2436. ARC PROTECTION During normal CRT operation, internal arcing may occasionally occur. Spark gaps, in the range of 200V, connected from the CRT cathodes to CRT ground will limit the maximum voltage, but to a value that is much higher than allowable on the LM2436. This fast, high voltage, high energy pulse can damage the LM2436 output stage. The application circuit shown in Figure 9 is designed to help clamp the voltage at the output of the LM2436 to a safe level. The clamp diodes, D1 and D2, should have a fast transient response, high peak current rating, low series impedance and low shunt capacitance. FDH400 or equivalent diodes are recommended. Do not use 1N4148 diodes for the clamp diodes. D1 and D2 should have short, low impedance connections to VCC and ground respectively. The cathode of D1 should be located very close to a separately decoupled bypass capacitor (C3 in Figure 9). The ground connection of D2 and the decoupling capacitor should be very close to the LM2436 ground. This will significantly reduce the high frequency voltage transients that the LM2436 would be subjected to during an arcover condition. Resistor R2 limits the arcover current that is seen by the diodes while R1 limits the current into the LM2436 as well as the voltage stress at the outputs of the device. R2 should be a 1⁄2W solid carbon type resistor. R1 can be a 1⁄4W metal or carbon film type resistor. Having large value resistors for R1 and R2 would be desirable, but this has the effect of increasing rise and fall times. Inductor L1 is critical to reduce the initial high frequency voltage levels that the LM2436 would be subjected to. The inductor will not only help protect the device but it will also help minimize rise and fall times as well as minimize EMI. For proper arc protection, it is important to not omit any of the arc protection components shown in Figure 9. Application Hints INTRODUCTION National Semiconductor (NSC) is committed to provide application information that assists our customers in obtaining the best performance possible from our products. The following information is provided in order to support this commitment. The reader should be aware that the optimization of performance was done using a specific printed circuit board designed at NSC. Variations in performance can be realized due to physical changes in the printed circuit board and the application. Therefore, the designer should know that component value changes may be required in order to optimize performance in a given application. The values shown in this document can be used as a starting point for evaluation purposes. When working with high bandwidth circuits, good layout practices are also critical to achieving maximum performance. IMPORTANT INFORMATION The LM2436 performance is targeted for the XGA (1024 x 768, 85 Hz refresh) resolution market. The application circuits shown in this document to optimize performance and to www.national.com 6 LM2436 Application Hints (Continued) 20043510 FIGURE 9. One Channel of the LM2436 with the Recommended Application Circuit OPTIMIZING TRANSIENT RESPONSE Referring to Figure 9, there are three components (R1, R2 and L1) that can be adjusted to optimize the transient response of the application circuit. Increasing the values of R1 and R2 will slow the circuit down while decreasing overshoot. Increasing the value of L1 will speed up the circuit as well as increase overshoot. It is very important to use inductors with very high self-resonant frequencies, preferably above 300 MHz. Ferrite core inductors from J.W. Miller Magnetics (part # 78FR56M) were used for optimizing the performance of the device in the NSC application board. The values shown in Figure 9 can be used as a good starting point for the evaluation of the LM2436. The NSC demo board also has a position open to add a resistor in parallel with L1. This resistor can be used to help control overshoot. Using variable resistors for R1 and the parallel resistor will simplify finding the values needed for optimum performance in a given application. Once the optimum values are determined the variable resistors can be replaced with fixed values. EFFECT OF LOAD CAPACITANCE Figure 8 shows the effect of increased load capacitance on the speed of the device. This demonstrates the importance of knowing the load capacitance in the application. EFFECT OF OFFSET Figure 7 shows the variation in rise and fall times when the output offset of the device is varied from 40 to 50 VDC. The rise time shows a maximum variation relative to the center data point (45 VDC) less than 5%. The fall time shows a variation less than 4% relative to the center data point. THERMAL CONSIDERATIONS Figure 4 shows the performance of the LM2436 in the test circuit shown in Figure 2 as a function of case temperature. The figure shows that the rise time of the LM2436 increases by approximately 8% as the case temperature increases from 40˚C to 100˚C. This corresponds to a speed degradation of 1.3% for every 10˚C rise in case temperature.The fall time increases by approximately 4% as the case temperature increases from 40˚C to 100˚C. Figure 6 shows the maximum power dissipation of the LM2436 vs. Frequency when all three channels of the device are driving an 8 pF load with a 40 Vp-p alternating one pixel on, one pixel off signal. The graph assumes a 72% active 7 www.national.com time (device operating at the specified frequency) which is typical in a monitor application. The other 28% of the time the device is assumed to be sitting at the black level (65V in this case). This graph gives the designer the information needed to determine the heat sink requirement for his application. The designer should note that if the load capacitance is increased the AC component of the total power dissipation will also increase. The LM2436 case temperature must be maintained below 100˚C. If the maximum expected ambient temperature inside the monitor is 70˚C and the power dissipation is 4.2W (from Figure 6, 50 MHz max video frequency) then a maximum heat sink thermal resistance can be calculated: This example assumes a capacitive load of 8 pF and no resistive load. TYPICAL APPLICATION A typical application of the LM2436 is shown in Figure 11. Used in conjunction with an LM1279, a complete video channel from monitor input to CRT cathode can be achieved. Performance is ideal for 1024 x 768 resolution displays with pixel clock frequencies up to 100 MHz. Figure 11 is the schematic for the NSC demonstration board that can be used to evaluate the LM1279/2436 combination in a monitor, and Figure 10 shows the response at the red cathode for this application. The input video rise time is 3.2ns, and the peaking component values are those recommended in Figure 11. Table 1 shows the typical cathode response of all three channels. LM2436 Application Hints (Continued) Pease, Robert A., “Troubleshooting Analog Circuits”, Butterworth-Heinemann, 1991. Because of its high small signal bandwidth, the part may oscillate in a monitor if feedback occurs around the video channel through the chassis wiring. To prevent this, leads to the video amplifier input circuit should be shielded, and input circuit wiring should be spaced as far as possible from output circuit wiring. NSC DEMONSTRATION BOARD Figure 12 shows the routing and component placement on the NSC LM1279/2436 demonstration board. The schematic of the board is shown in Figure 11. This board provides a good example of a layout that can be used as a guide for future layouts. Note the location of the following components: • C55 — VCC bypass capacitor, located very close to pin 4 and ground pins • C43, C44 — VBB bypass capacitors, located close to pin 8 and ground • C53–C56 — VCC bypass capacitors, near LM2436 and VCC clamp diodes. Very important for arc protection. The routing of the LM2436 outputs to the CRT is very critical to achieving optimum performance. Figure 13 shows the routing and component placement from pin 1 of the LM2436 to the blue cathode. Note that the components are placed so that they almost line up from the output pin of the LM2436 to the blue cathode pin of the CRT connector. This is done to minimize the length of the video path between these two components. Note also that D14, D15, R29 and D13 are placed to minimize the size of the video nodes that they are attached to. This minimizes parasitic capacitance in the video path and also enhances the effectiveness of the protection diodes. The anode of protection diode D14 is connected directly to a section of the the ground plane that has a short and direct path to the LM2436 ground pins. The cathode of D15 is connected to VCC very close to decoupling capacitor C55 (see Figure 13) which is connected to the same section of the ground plane as D14. The diode placement and routing is very important for minimizing the voltage stress on the LM2436 during an arcover event. Lastly, notice that S3 is placed very close to the blue cathode and is tied directly to CRT ground. 20043521 Red Cathode Response FIGURE 10. TABLE 1. LM2436 Cathode Response tr/OS Red Green Blue 7.7 ns / 7% 7.7 ns / 6% 7.4 ns / 7% tf/OS 7.7 ns / 5% 7.5 ns / 6% 7.3 ns / 7% PC BOARD LAYOUT CONSIDERATIONS For optimum performance, an adequate ground plane, isolation between channels, good supply bypassing and minimizing unwanted feedback are necessary. Also, the length of the signal traces from the preamplifier to the LM2436 and from the LM2436 to the CRT cathode should be as short as possible. The following references are recommended: Ott, Henry W., “Noise Reduction Techniques in Electronic Systems”, John Wiley & Sons, New York, 1976. “Video Amplifier Design for Computer Monitors”, National Semiconductor Application Note 1013. www.national.com 8 Application Hints (Continued) LM2436 9 20043511 FIGURE 11. LM1279/243X Demonstration Board Schematic www.national.com LM2436 Application Hints (Continued) 20043513 FIGURE 12. LM1279/243X Demo Board Layout www.national.com 10 LM2436 Application Hints (Continued) 20043514 FIGURE 13. Trace Routing and Component Placement for Blue Channel Output 11 www.national.com LM2436 Physical Dimensions unless otherwise noted inches (millimeters) CONTROLLING DIMENSION IS INCH VALUES IN [ ] ARE MILLIMETERS NS Package Number TA09A Order Number LM2436TA www.national.com 12 LM2436 Monolithic Triple 7.5 ns CRT Driver Notes LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Email: support@nsc.com National Semiconductor Europe Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: ap.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 www.national.com National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.