LM317T

LM117/LM317A/LM317 3-Terminal Adjustable Regulator April 2007 LM117/LM317A/LM317 3-Terminal Adjustable Regulator General Description The LM117 series of adjustable 3-terminal positive voltage regulators is capable of supplying in excess of 1.5A over a 1.2V to 37V output range. They are exceptionally easy to use and require only two external resistors to set the output voltage. Further, both line and load regulation are better than standard fixed regulators. Also, the LM117 is packaged in standard transistor packages which are easily mounted and handled. In addition to higher performance than fixed regulators, the LM117 series offers full overload protection available only in IC's. Included on the chip are current limit, thermal overload protection and safe area protection. All overload protection circuitry remains fully functional even if the adjustment terminal is disconnected. Normally, no capacitors are needed unless the device is situated more than 6 inches from the input filter capacitors in which case an input bypass is needed. An optional output capacitor can be added to improve transient response. The adjustment terminal can be bypassed to achieve very high ripple rejection ratios which are difficult to achieve with standard 3-terminal regulators. Besides replacing fixed regulators, the LM117 is useful in a wide variety of other applications. Since the regulator is “floating” and sees only the input-to-output differential voltage, supplies of several hundred volts can be regulated as long as the maximum input to output differential is not exceeded, i.e., avoid short-circuiting the output. Also, it makes an especially simple adjustable switching regulator, a programmable output regulator, or by connecting a fixed resistor between the adjustment pin and output, the LM117 can be used as a precision current regulator. Supplies with electronic shutdown can be achieved by clamping the adjustment terminal to ground which programs the output to 1.2V where most loads draw little current. For applications requiring greater output current, see LM150 series (3A) and LM138 series (5A) data sheets. For the negative complement, see LM137 series data sheet. Features ■ ■ ■ ■ ■ ■ ■ ■ ■ Guaranteed 1% output voltage tolerance (LM317A) Guaranteed max. 0.01%/V line regulation (LM317A) Guaranteed max. 0.3% load regulation (LM117) Guaranteed 1.5A output current Adjustable output down to 1.2V Current limit constant with temperature P+ Product Enhancement tested 80 dB ripple rejection Output is short-circuit protected Typical Applications 1.2V–25V Adjustable Regulator LM117/LM317A/LM317 Package Options Part Number LM117, LM317 LM317 LM317 LM317A, LM317 LM117, LM317A, LM317 LM117 LM317A, LM317 Suffix K T S EMP H E MDT Package TO-3 TO-220 TO-263 SOT-223 TO-39 LCC TO-252 Output Current 1.5A 1.5A 1.5A 1.0A 0.5A 0.5A 0.5A 906301 SOT-223 vs. TO-252 (D-Pak) Packages Full output current not available at high input-output voltages *Needed if device is more than 6 inches from filter capacitors. †Optional—improves transient response. Output capacitors in the range of 1μF to 1000μF of aluminum or tantalum electrolytic are commonly used to provide improved output impedance and rejection of transients. 906354 Scale 1:1 © 2007 National Semiconductor Corporation 9063 www.national.com LM117/LM317A/LM317 Connection Diagrams TO-3 (K) Metal Can Package TO-39 (H) Metal Can Package 906331 CASE IS OUTPUT 906330 CASE IS OUTPUT Bottom View NS Package Number H03A Bottom View Steel Package NS Package Number K02A or K02C TO-263 (S) Surface-Mount Package TO-220 (T) Plastic Package 906335 Top View 906332 Front View NS Package Number T03B TO-263 (S) Surface-Mount Package Ceramic Leadless Chip Carrier (E) 906336 Side View NS Package Number TS3B 906334 Top View NS Package Number E20A www.national.com 2 LM117/LM317A/LM317 4-Lead SOT-223 (EMP) TO-252 (MDT) 906359 Front View NS Package Number MP04A 906366 Front View NS Package Number TD03B Ordering Information Package TO-3 Metal Can (K) TO-220 3- Lead TO-263 3- Lead SOT-223 4- Lead Temperature Range −55°C ≤ TJ ≤ +150°C 0°C ≤ TJ ≤ +125°C −55°C ≤ TJ ≤ +150°C −40°C ≤ TJ ≤ +125°C 0°C ≤ TJ ≤ +125°C 0°C ≤ TJ ≤ +125°C 0°C ≤ TJ ≤ +125°C −40°C ≤ TJ ≤ +125°C −55°C ≤ TJ ≤ +150°C TO-39 Metal Can (H) LCC TO-252 3- Lead D-Pack −55°C ≤ TJ ≤ +150°C −40°C ≤ TJ ≤ +125°C 0°C ≤ TJ ≤ +125°C −55°C ≤ TJ ≤ +150°C 0°C ≤ TJ ≤ +125°C −40°C ≤ TJ ≤ +125°C Output Current 1.5A 1.5A 1.5A 1.5A 1.5A 1.5A 1.0A 1.0A 0.5A 0.5A 0.5A 0.5A 0.5A 0.5A 0.5A Order Number LM117K STEEL LM317K STEEL LM117K/883 LM317AT LM317T LM317S LM317SX LM317EMP LM317EMPX LM317AEMP LM317AEMPX LM117H LM117H/883 LM317AH LM317H LM117E/883 LM317MDT LM317MDTX LM317AMDT LM317AMDTX Package Marking LM117K STEEL P+ LM317K STEEL P+ LM117K/883 LM317AT P+ LM317T P+ LM317S P+ N01A N07A LM117H P+ LM117H/883 LM317AH P+ LM317H P+ LM117E/883 LM317MDT LM317AMDT Transport Media 50 Per Bag 50 Per Bag 50 Per Bag 45 Units/Rail 45 Units/Rail 45 Units/Rail 500 Units Tape and Reel 1k Units Tape and Reel 2k Units Tape and Reel 1k Units Tape and Reel 2k Units Tape and Reel 500 Per Box 20 Per Tray 500 Per Box 500 Per Box 50 Units/Rail 75 Units/Rail 2.5k Units Tape and Reel 75 Units/Rail 2.5k Units Tape and Reel TD03B E20A H03A MP04A NSC Drawing K02A K02C T03B TS3B 3 www.national.com LM117/LM317A/LM317 Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Power Dissipation Internally Limited Input-Output Voltage Differential +40V, −0.3V Storage Temperature −65°C to +150°C Lead Temperature Metal Package (Soldering, 10 seconds) 300°C Plastic Package (Soldering, 4 seconds) 260°C ESD Tolerance (Note 5) 3 kV Operating Temperature Range LM117 LM317A LM317 Preconditioning Thermal Limit Burn-In All Devices 100% −55°C ≤ TJ ≤ +150°C −40°C ≤ TJ ≤ +125°C 0°C ≤ TJ ≤ +125°C LM117 Electrical Characteristics (Note 3) Specifications with standard type face are for TJ = 25°C, and those with boldface type apply over full Operating Temperature Range. Unless otherwise specified, VIN − VOUT = 5V, and IOUT = 10 mA. Parameter Reference Voltage Line Regulation Load Regulation Thermal Regulation Adjustment Pin Current Adjustment Pin Current Change Temperature Stability Minimum Load Current 10 mA ≤ IOUT ≤ IMAX TMIN ≤ TJ ≤ TMAX (VIN − VOUT) = 40V (VIN − VOUT) ≤ 15V Current Limit K Package H, E Package (VIN − VOUT) = 40V K Package H, E Package RMS Output Noise, % of VOUT Ripple Rejection Ratio Long-Term Stability Thermal Resistance, θJC Junction-to-Case Thermal Resistance, θJA Junction-to-Ambient (No Heat Sink) 10 Hz ≤ f ≤ 10 kHz VOUT = 10V, f = 120 Hz, CADJ = 0 μF VOUT = 10V, f = 120 Hz, CADJ = 10 μF TJ = 125°C, 1000 hrs K (TO-3) Package H (TO-39) Package E (LCC) Package K (TO-3) Package H (TO-39) Package E (LCC) Package 66 0.3 0.15 0.4 0.20 0.003 65 80 0.3 2 21 12 39 186 88 1 A % dB dB % °C/W 1.5 0.5 2.2 0.8 3.4 1.8 A 3V ≤ (VIN − VOUT) ≤ 40V Conditions 3V ≤ (VIN − VOUT) ≤ 40V, 10 mA ≤ IOUT ≤ IMAX 3V ≤ (VIN − VOUT) ≤ 40V (Note 4) 10 mA ≤ IOUT ≤ IMAX (Note 4) 20 ms Pulse LM117 (Note 2) Min 1.20 Typ 1.25 0.01 0.02 0.1 0.3 0.03 50 0.2 1 3.5 5 Max 1.30 0.02 0.05 0.3 1 0.07 100 5 Units V %/V % %/W μA μA % mA °C/W www.national.com 4 LM117/LM317A/LM317 LM317A and LM317 Electrical Characteristics (Note 3) Specifications with standard type face are for TJ = 25°C, and those with boldface type apply over full Operating Temperature Range. Unless otherwise specified, VIN − VOUT = 5V, and IOUT = 10 mA. Parameter Conditions LM317A Min 1.238 Reference Voltage 3V ≤ (VIN − VOUT) ≤ 40V, 10 mA ≤ IOUT ≤ IMAX Line Regulation Load Regulation Thermal Regulation Adjustment Pin Current Adjustment Pin Current Change Temperature Stability Minimum Load Current 10 mA ≤ IOUT ≤ IMAX TMIN ≤ TJ ≤ TMAX (VIN − VOUT) = 40V (VIN − VOUT) ≤ 15V K, T, S Packages EMP Package H, MDT Packages (VIN − VOUT) = 40V K, T, S Packages EMP Package H, MDT Packages RMS Output Noise, % of VOUT Ripple Rejection Ratio Long-Term Stability 10 Hz ≤ f ≤ 10 kHz VOUT = 10V, f = 120 Hz, CADJ = 0 μF VOUT = 10V, f = 120 Hz, CADJ = 10 μF TJ = 125°C, 1000 hrs K (TO-3) Package T (TO-220) Package S (TO-263) Package EMP (SOT-223) Package H (TO-39) Package MDT (TO-252) Package K (TO-3) Package T (TO-220) Package S (TO-263) Package (Note 6) EMP (SOT-223) Package (Note 6) H (TO-39) Package MDT (TO-252) Package (Note 6) 66 0.112 0.075 0.30 0.20 0.003 65 80 0.3 23.5 21 12 140 186 103 1 66 0.15 0.112 0.075 0.40 0.30 0.20 0.003 65 80 0.3 2 4 4 23.5 21 12 39 50 50 140 186 103 1 A % dB dB % 1.5 0.5 2.2 0.8 3.4 1.8 1.5 1.5 0.5 2.2 2.2 0.8 3.4 3.4 1.8 A 3V ≤ (VIN − VOUT) ≤ 40V 3V ≤ (VIN − VOUT) ≤ 40V (Note 4) 10 mA ≤ IOUT ≤ IMAX (Note 4) 20 ms Pulse 1.225 Typ 1.250 1.250 0.005 0.01 0.1 0.3 0.04 50 0.2 1 3.5 10 Max 1.262 1.270 0.01 0.02 0.5 1 0.07 100 5 Min 1.20 LM317 Typ 1.25 1.25 0.01 0.02 0.1 0.3 0.04 50 0.2 1 3.5 10 Max 1.30 0.04 0.07 0.5 1.5 0.07 100 5 Units V V %/V % %/W μA μA % mA Current Limit Thermal Resistance, θJC Junction-to-Case °C/W Thermal Resistance, θJA Junction-to-Ambient (No Heat Sink) °C/W Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Note 2: Refer to RETS117H drawing for the LM117H, or the RETS117K for the LM117K military specifications. Note 3: IMAX = 1.5A for the K (TO-3), T (TO-220), and S (TO-263) packages. IMAX = 1.0A for the EMP (SOT-223) package. IMAX = 0.5A for the H (TO-39), MDT (TO-252), and E (LCC) packages. Device power dissipation (PD) is limited by ambient temperature (TA), device maximum junction temperature (TJ), and package thermal resistance (θJA). The maximum allowable power dissipation at any temperature is : PD(MAX) = ((TJ(MAX) - TA)/θJA). All Min. and Max. limits are guaranteed to National's Average Outgoing Quality Level (AOQL). Note 4: Regulation is measured at a constant junction temperature, using pulse testing with a low duty cycle. Changes in output voltage due to heating effects are covered under the specifications for thermal regulation. Note 5: Human body model, 100 pF discharged through a 1.5 kΩ resistor. Note 6: When surface mount packages are used (TO-263, SOT-223, TO-252), the junction to ambient thermal resistance can be reduced by increasing the PC board copper area that is thermally connected to the package. See the Applications Hints section for heatsink techniques. 5 www.national.com LM117/LM317A/LM317 Typical Performance Characteristics Load Regulation Output Capacitor = 0 μF unless otherwise noted Current Limit 906337 906338 Adjustment Current Dropout Voltage 906339 906340 Temperature Stability Minimum Operating Current 906341 906342 www.national.com 6 LM117/LM317A/LM317 Ripple Rejection Ripple Rejection 906343 906344 Ripple Rejection Output Impedance 906345 906346 Line Transient Response Load Transient Response 906347 906348 7 www.national.com LM117/LM317A/LM317 Application Hints In operation, the LM117 develops a nominal 1.25V reference voltage, VREF, between the output and adjustment terminal. The reference voltage is impressed across program resistor R1 and, since the voltage is constant, a constant current I1 then flows through the output set resistor R2, giving an output voltage of aluminum electrolytic) on the output swamps this effect and insures stability. Any increase of the load capacitance larger than 10 μF will merely improve the loop stability and output impedance. LOAD REGULATION The LM117 is capable of providing extremely good load regulation but a few precautions are needed to obtain maximum performance. The current set resistor connected between the adjustment terminal and the output terminal (usually 240Ω) should be tied directly to the output (case) of the regulator rather than near the load. This eliminates line drops from appearing effectively in series with the reference and degrading regulation. For example, a 15V regulator with 0.05Ω resistance between the regulator and load will have a load regulation due to line resistance of 0.05Ω × IL. If the set resistor is connected near the load the effective line resistance will be 0.05Ω (1 + R2/R1) or in this case, 11.5 times worse. Figure 2 shows the effect of resistance between the regulator and 240Ω set resistor. (1) 906305 FIGURE 1. Since the 100μA current from the adjustment terminal represents an error term, the LM117 was designed to minimize IADJ and make it very constant with line and load changes. To do this, all quiescent operating current is returned to the output establishing a minimum load current requirement. If there is insufficient load on the output, the output will rise. EXTERNAL CAPACITORS An input bypass capacitor is recommended. A 0.1μF disc or 1μF solid tantalum on the input is suitable input bypassing for almost all applications. The device is more sensitive to the absence of input bypassing when adjustment or output capacitors are used but the above values will eliminate the possibility of problems. The adjustment terminal can be bypassed to ground on the LM117 to improve ripple rejection. This bypass capacitor prevents ripple from being amplified as the output voltage is increased. With a 10 μF bypass capacitor 80dB ripple rejection is obtainable at any output level. Increases over 10 μF do not appreciably improve the ripple rejection at frequencies above 120Hz. If the bypass capacitor is used, it is sometimes necessary to include protection diodes to prevent the capacitor from discharging through internal low current paths and damaging the device. In general, the best type of capacitors to use is solid tantalum. Solid tantalum capacitors have low impedance even at high frequencies. Depending upon capacitor construction, it takes about 25 μF in aluminum electrolytic to equal 1μF solid tantalum at high frequencies. Ceramic capacitors are also good at high frequencies; but some types have a large decrease in capacitance at frequencies around 0.5 MHz. For this reason, 0.01 μF disc may seem to work better than a 0.1 μF disc as a bypass. Although the LM117 is stable with no output capacitors, like any feedback circuit, certain values of external capacitance can cause excessive ringing. This occurs with values between 500 pF and 5000 pF. A 1 μF solid tantalum (or 25 μF www.national.com 8 906306 FIGURE 2. Regulator with Line Resistance in Output Lead With the TO-3 package, it is easy to minimize the resistance from the case to the set resistor, by using two separate leads to the case. However, with the TO-39 package, care should be taken to minimize the wire length of the output lead. The ground of R2 can be returned near the ground of the load to provide remote ground sensing and improve load regulation. PROTECTION DIODES When external capacitors are used with any IC regulator it is sometimes necessary to add protection diodes to prevent the capacitors from discharging through low current points into the regulator. Most 10 μF capacitors have low enough internal series resistance to deliver 20A spikes when shorted. Although the surge is short, there is enough energy to damage parts of the IC. When an output capacitor is connected to a regulator and the input is shorted, the output capacitor will discharge into the output of the regulator. The discharge current depends on the value of the capacitor, the output voltage of the regulator, and the rate of decrease of VIN. In the LM117, this discharge path is through a large junction that is able to sustain 15A surge with no problem. This is not true of other types of positive regulators. For output capacitors of 25 μF or less, there is no need to use diodes. The bypass capacitor on the adjustment terminal can discharge through a low current junction. Discharge occurs when either the input, or the output, is shorted. Internal to the LM117 is a 50Ω resistor which limits the peak discharge current. No protection is needed for output voltages of 25V or less and 10 μF capacitance. Figure 3 shows an LM117 with protection LM117/LM317A/LM317 diodes included for use with outputs greater than 25V and high values of output capacitance. 906360 FIGURE 4. Power Dissipation Diagram If the calculated maximum allowable thermal resistance is higher than the actual package rating, then no additional work is needed. If the calculated maximum allowable thermal resistance is lower than the actual package rating either the power dissipation (PD) needs to be reduced, the maximum ambient temperature TA(MAX) needs to be reduced, the thermal resistance (θJA) must be lowered by adding a heatsink, or some combination of these. If a heatsink is needed, the value can be calculated from the formula: θHA ≤ (θJA - (θCH + θJC)) (6) 906307 (2) D1 protects against C1 D2 protects against C2 FIGURE 3. Regulator with Protection Diodes HEATSINK REQUIREMENTS The LM317 regulators have internal thermal shutdown to protect the device from over-heating. Under all operating conditions, the junction temperature of the LM317 should not exceed the rated maximum junction temperature (TJ) of 150° C for the LM117, or 125°C for the LM317A and LM317. A heatsink may be required depending on the maximum device power dissipation and the maximum ambient temperature of the application. To determine if a heatsink is needed, the power dissipated by the regulator, PD, must be calculated: PD = ((VIN − VOUT) × IL) + (VIN × IG) (3) Figure 4 shows the voltage and currents which are present in the circuit. The next parameter which must be calculated is the maximum allowable temperature rise, TR(MAX): TR(MAX) = TJ(MAX) − TA(MAX) (4) where ( θCH is the thermal resistance of the contact area between the device case and the heatsink surface, and θJC is thermal resistance from the junction of the die to surface of the package case. When a value for θ(H−A) is found using the equation shown, a heatsink must be selected that has a value that is less than, or equal to, this number. The θ(H−A) rating is specified numerically by the heatsink manufacturer in the catalog, or shown in a curve that plots temperature rise vs power dissipation for the heatsink. HEATSINKING SURFACE MOUNT PACKAGES The TO-263 (S), SOT-223 (EMP) and TO-252 (MDT) packages use a copper plane on the PCB and the PCB itself as a heatsink. To optimize the heat sinking ability of the plane and PCB, solder the tab of the package to the plane. HEATSINKING THE SOT-223 PACKAGE Figure 5 and Figure 6 show the information for the SOT-223 package. Figure 6 assumes a θ(J−A) of 74°C/W for 1 ounce copper and 51°C/W for 2 ounce copper and a maximum junction temperature of 125°C. Please see AN-1028 for thermal enhancement techniques to be used with SOT-223 and TO-252 packages. where TJ(MAX) is the maximum allowable junction temperature (150°C for the LM117, or 125°C for the LM317A/LM317), and TA(MAX) is the maximum ambient temperature which will be encountered in the application. Using the calculated values for TR(MAX) and PD, the maximum allowable value for the junction-to-ambient thermal resistance (θJA) can be calculated: θJA = (TR(MAX) / PD) (5) 9 www.national.com LM117/LM317A/LM317 906357 906355 FIGURE 5. θ(J−A) vs Copper (2 ounce) Area for the SOT-223 Package FIGURE 7. θ(J−A) vs Copper (1 ounce) Area for the TO-263 Package As a design aid, Figure 8 shows the maximum allowable power dissipation compared to ambient temperature for the TO-263 device (assuming θ(J−A) is 35°C/W and the maximum junction temperature is 125°C). 906358 FIGURE 6. Maximum Power Dissipation vs TAMB for the SOT-223 Package HEATSINKING THE TO-263 PACKAGE Figure 7 shows for the TO-263 the measured values of θ(J −A) for different copper area sizes using a typical PCB with 1 ounce copper and no solder mask over the copper area used for heatsinking. As shown in Figure 7, increasing the copper area beyond 1 square inch produces very little improvement. It should also be observed that the minimum value of θ(J−A) for the TO-263 package mounted to a PCB is 32°C/W. 906356 FIGURE 8. Maximum Power Dissipation vs TAMB for the TO-263 Package HEATSINKING THE TO-252 PACKAGE If the maximum allowable value for θJA is found to be ≥103° C/W (Typical Rated Value) for TO-252 package, no heatsink is needed since the package alone will dissipate enough heat to satisfy these requirements. If the calculated value for θJA falls below these limits, a heatsink is required. As a design aid, Table 1 shows the value of the θJA of TO-252 for different heatsink area. The copper patterns that we used to measure these θJAs are shown at the end of the Application Notes Section. Figure 9 reflects the same test results as what are in Table 1. Figure 10 shows the maximum allowable power dissipation vs. ambient temperature for the TO-252 device. Figure 11 shows the maximum allowable power dissipation vs. copper area (in2) for the TO-252 device. Please see AN-1028 for thermal enhancement techniques to be used with SOT-223 and TO-252 packages. www.national.com 10 LM117/LM317A/LM317 TABLE 1. θJA Different Heatsink Area Layout Top Side 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 (in2)* 0.0123 0.066 0.3 0.53 0.76 1.0 0.066 0.066 0.066 0.066 0.066 0.066 0.175 0.284 0.392 0.5 Copper Area Bottom Side 0 0 0 0 0 0 0.2 0.4 0.6 0.8 1.0 0.066 0.175 0.284 0.392 0.5 (in2) Thermal Resistance (θJA°C/W) TO-252 103 87 60 54 52 47 84 70 63 57 57 89 72 61 55 53 Note: * Tab of device attached to topside of copper. 906361 FIGURE 9. θJA vs 2oz Copper Area for TO-252 11 www.national.com LM117/LM317A/LM317 906363 FIGURE 10. Maximum Allowable Power Dissipation vs. Ambient Temperature for TO-252 906362 FIGURE 11. Maximum Allowable Power Dissipation vs. 2oz Copper Area for TO-252 www.national.com 12 LM117/LM317A/LM317 906364 FIGURE 12. Top View of the Thermal Test Pattern in Actual Scale 13 www.national.com LM117/LM317A/LM317 906365 FIGURE 13. Bottom View of the Thermal Test Pattern in Actual Scale Schematic Diagram 906308 www.national.com 14 LM117/LM317A/LM317 Typical Applications 5V Logic Regulator with Electronic Shutdown* †Solid tantalum *Discharges C1 if output is shorted to ground High Stability 10V Regulator *Min. output ≊ 1.2V 906303 Slow Turn-On 15V Regulator 906311 906309 Adjustable Regulator with Improved Ripple Rejection 906310 15 www.national.com LM117/LM317A/LM317 High Current Adjustable Regulator 906312 ‡Optional—improves ripple rejection †Solid tantalum *Minimum load current = 30 mA 0 to 30V Regulator Power Follower 906313 Full output current not available at high input-output voltages 906314 www.national.com 16 LM117/LM317A/LM317 5A Constant Voltage/Constant Current Regulator 906315 †Solid tantalum *Lights in constant current mode 1A Current Regulator *Minimum load current ≊ 4 mA High Gain Amplifier 906316 1.2V–20V Regulator with Minimum Program Current 906318 906317 17 www.national.com LM117/LM317A/LM317 Low Cost 3A Switching Regulator 906319 †Solid tantalum *Core—Arnold A-254168-2 60 turns 4A Switching Regulator with Overload Protection 906320 †Solid tantalum *Core—Arnold A-254168-2 60 turns Precision Current Limiter 906321 www.national.com 18 LM117/LM317A/LM317 Tracking Preregulator 906322 Current Limited Voltage Regulator 906323 (Compared to LM117's higher current limit) —At 50 mA output only ¾ volt of drop occurs in R3 and R4 Adjusting Multiple On-Card Regulators with Single Control* 906324 *All outputs within ±100 mV †Minimum load—10 mA 19 www.national.com LM117/LM317A/LM317 AC Voltage Regulator 906325 12V Battery Charger 906326 Use of RS allows low charging rates with fully charged battery. 50mA Constant Current Battery Charger 906327 www.national.com 20 LM117/LM317A/LM317 Adjustable 4A Regulator 906328 Current Limited 6V Charger Digitally Selected Outputs 906329 *Sets peak current (0.6A for 1Ω) **The 1000μF is recommended to filter out input transients 906302 *Sets maximum VOUT 21 www.national.com LM117/LM317A/LM317 Physical Dimensions inches (millimeters) unless otherwise noted TO-3 Metal Can Package (K) NS Package Number K02A TO-3 Metal Can Package (K) Mil-Aero Product NS Package Number K02C www.national.com 22 LM117/LM317A/LM317 TO-39 Metal Can Package (H) NS Package Number H03A 3-Lead TO-220 (T) NS Package Number T03B 23 www.national.com LM117/LM317A/LM317 3-Lead TO-263 (S) NS Package Number TS3B Ceramic Leadless Chip Carrier (E) NS Package Number E20A www.national.com 24 LM117/LM317A/LM317 4-Lead SOT-223 (EMP) NS Package Number MP04A 3-Lead D-Pack (MDT) NS Package Number TD03B 25 www.national.com LM117/LM317A/LM317 3-Terminal Adjustable Regulator Notes THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION (“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright© 2007 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530-85-86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +49 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 www.national.com