LM321MFX

LM321 Low Power Single Op Amp April 2001 LM321 Low Power Single Op Amp General Description The LM321 brings performance and economy to low power systems. With a high unity gain frequency and a guaranteed 0.4V/µs slew rate, the quiescent current is only 430µA/amplifier (5V). The input common mode range includes ground and therefore the device is able to operate in single supply applications as well as in dual supply applications. It is also capable of comfortably driving large capacitive loads. The LM321 is available in the SOT23-5 package. Overall the LM321 is a low power, wide supply range performance op amp that can be designed into a wide range of applications at an economical price without sacrificing valuable board space. Features (VCC = 5V, TA = 25˚C. Typical values unless specified). n Gain-Bandwidth product 1MHz n Low supply current 430µA n Low input bias current 45nA n Wide supply voltage range +3V to +32V n Stable with high capacitive loads n Single version of LM324 Applications n n n n n Chargers Power supplies Industrial: controls, instruments Desktops Communications infrastructure Connection Diagram SOT23-5 Application Circuit DC Summing Amplifier (VIN’s ≥ 0 VDC and VO ≥ VDC) 20007601 Top View 20007607 Where: V0 = V1 + V2 - V3 - V4, (V1+ V2) ≥ (V3 + V4) to keep VO > 0 VDC Ordering Information Package 5-Pin SOT-23 Part Number LM321MF LM321MFX Package Marking A63A Transport Media 1k Units Tape and Reel 3k Units Tape and Reel NSC Drawing MF05A © 2001 National Semiconductor Corporation DS200076 www.national.com LM321 Absolute Maximum Ratings (Note 1) Junction Temperature (Note 3) Mounting Temperature Lead Temp (Soldering, 10 sec) Infrared (10 sec) Thermal Resistance to Ambient (θJA) ESD Tolerance (Note 10) 150˚C 260˚C 215˚C 265˚C/W 300V If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Differential Input Voltage Input Current (VIN < −0.3V) (Note 6) Supply Voltage (V+ - V−) Input Voltage Output Short Circuit to GND, V+ ≤ 15V and TA = 25˚C (Note 2) Storage Temperature Range ± Supply Voltage 50mA 32V −0.3V to +32V Continuous −65˚C to 150˚C Operating Ratings (Note 1) Temperature Range Supply Voltage −40˚C to 85˚C 3V to 30V Electrical Characteristics Symbol VOS IOS IB VCM AV PSRR CMRR VO Parameter Input Offset Voltage Input Offset Current Input Bias Current (Note 8) Unless otherwise specified, all limits guaranteed for at TA = 25˚C; V+ = 5V, V− = 0V, VO = 1.4V. Boldface limits apply at temperature extremes. Conditions (Note 7) Min (Note 5) Typ (Note 4) 2 5 45 V+ = 30V (Note 9) For CMRR > = 50dB (V+ = 15V, RL = 2kΩ VO = 1.4V to 11.4V) RS ≤ 10kΩ, V+ ≤ 5V to 30V RS ≤ 10kΩ VOH VOL V+ = 30V, RL = 2kΩ V+ = 30V, RL = 10kΩ V+ = 5V, RL = 10kΩ V = 5V V+ = 30V + Max (Note 5) 7 9 50 150 250 500 V+ - 1.5 V+ -2 Units mV nA nA V V/mV dB dB V Input Common-Mode Voltage Range Large Signal Voltage Gain Power Supply Rejection Ratio Common Mode Rejection Ratio Output Swing 0 25 15 65 65 26 27 28 5 0.430 0.7 0.660 1.5 20 10 10 5 12 40 20 20 8 100 40 100 100 85 20 1.15 1.2 2.85 3 mV mA IS Supply Current, No Load ISOURCE ISINK Output Current Sourcing Output Current Sinking VID = +1V, V+ = 15V, VO = 2V VID = −1V V+ = 15V, VO = 2V VID = −1V V+ = 15V, VO = 0.2V mA mA µA 85 mA IO SR Output Short Circuit to Ground (Note 2) Slew Rate V+ = 15V V+ = 15V, RL = 2kΩ, VIN = 0.5 to 3V CL = 100pF, Unity Gain V+ = 30V, f = 100kHz, VIN = 10mV, RL = 2kΩ, CL = 100pF 0.4 V/µs GBW Gain Bandwidth Product 1 60 MHz deg φm Phase Margin www.national.com 2 LM321 Electrical Characteristics Symbol THD Parameter Total Harmonic Distortion Unless otherwise specified, all limits guaranteed for at TA = 25˚C; V+ = 5V, V− = 0V, VO = 1.4V. Boldface limits apply at temperature extremes. (Continued) Conditions f = 1kHz, AV = 20dB RL = 2kΩ, VO = 2VPP, CL = 100pF, V+ = 30V f = 1kHz, RS = 100Ω V+ = 30V Min (Note 5) Typ (Note 4) 0.015 40 nV/ Max (Note 5) Units % en Equivalent Input Noise Voltage Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics. Note 2: Short circuits from the output V+ can cause excessive heating and eventual destruction. When considering short circuits to ground the maximum output current is approximately 40mA independent of the magnitude of V+. At values of supply voltage in excess of +15V, continuous short circuits can exceed the power dissipation ratings and cause eventual destruction. Note 3: The maximum power dissipation is a function of TJ(MAX), θJA , and TA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(MAX) - TA)/ θJA . All numbers apply for packages soldered directly onto a PC board. Note 4: Typical values represent the most likely parametric norm. Note 5: All limits are guaranteed by testing or statistical analysis. Note 6: This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector base junction of the input PNP transistors becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is also lateral NPN parasitic transistor action on the IC chip. This transistor action can cause the output voltages of the op amps to go to the V+ voltage level (or to ground for a large overdrive) for the time duration that an input is driven negative. This is not destructive and normal output states will re-establish when the input voltage, which was negative, again returns to a value greater than −0.36V (at 25˚C). Note 7: VO ≅ 1.4V, RS = 0Ω with V+ from 5V to 30V; and over the full input common-mode range (0V to V+ - 1.5V) at 25˚C. Note 8: The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output so no loading change exists on the input lines. Note 9: The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25˚C). The upper end of the common-mode voltage range is V+ - 1.5V at 25˚C, but either or both inputs can go to +32V without damage, independent of the magnitude of V+. Note 10: Human Body Model, 1.5kΩ in series with 100pF. Simplified Schematic 20007603 3 www.national.com LM321 Typical Performance Characteristics TA = 25˚C. Small Signal Pulse Response Unless otherwise specified, VS = +5V, single supply, Large Signal Pulse Response 20007604 20007605 Supply Current vs. Supply Voltage Sinking Current vs. Output Voltage 20007612 20007613 Source Current vs. Output Voltage Open Loop Frequency Response 20007617 20007614 www.national.com 4 LM321 Application Hints The LM321 op amp can operate with a single or dual power supply voltage, has true-differential inputs, and remain in the linear mode with an input common-mode voltage of 0 VDC. This amplifier operates over a wide range of power supply voltages, with little change in performance characteristics. At 25˚C amplifier operation is possible down to a minimum supply voltage of 3V. Large differential input voltages can be easily accommodated and, as input differential voltage protection diodes are not needed, no large input currents result from large differential input voltages. The differential input voltage may be larger than V+ without damaging the device. Protection should be provided to prevent the input voltages from going negative more than −0.3 VDC (at 25˚C). An input clamp diode with a resistor to the IC input terminal can be used. To reduce the power supply drain, the amplifier has a class A output stage for small signal levels which converts to class B in a large signal mode. This allows the amplifiers to both source and sink large output currents. Therefore both NPN and PNP external current boost transistors can be used to extend the power capability of the basic amplifiers. The output voltage needs to raise approximately 1 diode drop above ground to bias the on-chip vertical PNP transistor for output current sinking applications. For AC applications, where the load is capacitively coupled to the output of the amplifier, a resistor should be used, from the output of the amplifier to ground to increase the class A bias current and to reduce distortion. Capacitive loads which are applied directly to the output of the amplifier reduce the loop stability margin. Values of 50pF can be accommodated using the worst-case non-inverting unity gain connection. Large closed loop gains or resistive isolation should be used if large load capacitance must be driven by the amplifier. The bias network of the LM321 establishes a supply current which is independent of the magnitude of the power supply voltage over the range of from 3 VDC to 30 VDC. Output short circuits either to ground or to the positive power supply should be of short time duration. Units can be destroyed, not as a result of the short circuit current causing metal fusing, but rather due to the large increase in IC chip dissipation which will cause eventual failure due to excessive junction temperatures. The larger value of output source current which is available at 25˚C provides a larger output current capability at elevated temperatures than a standard IC op amp. The circuits presented in the section on typical applications emphasize operation on only a single power supply voltage. If complementary power supplies are available, all of the standard op amp circuits can be used. In general, introducing a pseudo-ground (a bias voltage reference of V+/2) will allow operation above and below this value in single power supply systems. Many application circuits are shown which take advantage of the wide input common-mode voltage range which includes ground. In most cases, input biasing is not required and input voltages which range to ground can easily be accommodated. Typical Applications Non-Inverting DC Gain (0V Input = 0V Output) 20007606 5 www.national.com LM321 Typical Applications (Continued) DC Summing Amplifier (VIN’s ≥ 0 VDC and VO ≥ VDC) Amplitude Modulator Circuit 20007607 20007602 Where: V0 = V1 + V2 - V3 - V4, (V1+ V2) ≥ (V3 + V4) to keep VO > 0 VDC Power Amplifier LED Driver 20007609 20007608 V0 = 0 VDC for VIN = 0 VDC, AV = 10 Fixed Current Sources Lamp Driver 20007611 20007610 www.national.com 6 LM321 SOT23-5 Tape and Reel Specification TAPE DIMENSIONS 20007615 8mm Tape Size 0.130 (3.3) DIM A 0.124 (3.15) DIM Ao 0.130 (3.3) DIM B 0.126 (3.2) DIM Bo 0.138 ± 0.002 (3.5 ± 0.05) DIM F 0.055 ± 0.004 (1.4 ± 0.11) DIM Ko 0.157 (4) DIM P1 0.315 ± 0.012 (8 ± 0.3) DIM W 7 www.national.com LM321 SOT23-5 Tape and Reel Specification REEL DIMENSIONS (Continued) 20007616 8mm Tape Size 7.00 330.00 A 0.059 1.50 B 0.512 13.00 C 0.795 20.20 D 2.165 55.00 N 0.331 + 0.059/−0.000 8.40 + 1.50/−0.00 W1 0.567 14.40 W2 W1 + 0.078/−0.039 W1 + 2.00/−1.00 W3 www.national.com 8 LM321 Low Power Single Op Amp Physical Dimensions inches (millimeters) unless otherwise noted 5-Pin SOT23 NS Package Number MF05A LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: ap.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.