LM345

LM145 LM345 Negative Three Amp Regulator January 1995 LM145 LM345 Negative Three Amp Regulator General Description The LM145 is a three-terminal negative regulator with a fixed output voltage of b5V and up to 3A load current capability This device needs only one external component a compensation capacitor at the output making it easy to apply Worst case guarantees on output voltage deviation due to any combination of line load or temperature variation assure satisfactory system operation Exceptional effort has been made to make the LM145 immune to overload conditions The regulator has current limiting which is independent of temperature combined with thermal overload protection Internal current limiting protects against momentary faults while thermal shutdown prevents junction temperatures from exceeding safe limits during prolonged overloads Although primarily intended for fixed output voltage applications the LM145 may be programmed for higher output voltages with a simple resistive divider The low quiescent drain current of the device allows this technique to be used with good regulation The LM145 comes in a hermetic TO-3 package rated at 25W A reduced temperature range part LM345 is also available Features Y Y Y Y Y Y Y Y Output voltage accurate to better than g 2% Current limit constant with temperature Internal thermal shutdown protection Operates with input-output voltage differential of 2 8V at full rated load over full temperature range Regulation guaranteed with 25W power dissipation 3A output current guaranteed Only one external component needed P a Product Enhancement tested Schematic Diagram TL H 7785 – 1 C1995 National Semiconductor Corporation TL H 7785 RRD-B30M115 Printed in U S A Absolute Maximum Ratings If Military Aerospace specified devices are required please contact the National Semiconductor Sales Office Distributors for availability and specifications (Note 3) Input Voltage 20V Input-Output Differential 20V Power Dissipation Internally Limited Operating Junction Temperature Range b 55 C to a 150 C LM145 LM345 0 C to a 125 C b 65 C to a 150 C Storage Temperature Range Lead Temperature (Soldering 10 sec ) 300 C Electrical Characteristics (Note 1) Limits Parameter Conditions Min Output Voltage Line Regulation (Note 2) Load Regulation (Note 2) Output Voltage Tj e 25 C IOUT e 5 mA VIN e b7 5 Tj e 25 C b 20V s VIN s b 7 5V Tj e 25 C VIN e b7 5V 5 mA s IOUT s 3A b 20V s VIN s b 7 8V 5 mA s IOUT s 3A P s 25W TMIN s Tj s TMAX b 20V s VIN s b 7 5V 5 mA s IOUT s 3A b 5 20 b5 1 LM145 Typ b5 0 LM345 Max b4 9 Units Max b4 8 Min b5 2 Typ b5 0 V mV mV 5 30 15 75 5 30 25 100 b 4 80 b 5 25 b 4 75 V Quiescent Current Short Circuit Current Output Noise Voltage Long Term Stability Thermal Resistance Junction to Case 10 4 2 150 5 2 30 55 35 10 4 2 150 30 55 35 mA A A mV VIN e b7 5V Tj e a 25 C VIN e b20V Tj e a 25 C TA e 25 C CL e 4 7 mF 10 Hz s f s 100 kHz 50 5 2 50 mV CW Note 1 Unless otherwise specified these specifications apply b 55 C s Tj s a 150 C for the LM145 and 0 C s Tj s a 125 C for the LM345 VIN e 7 5V and IOUT e 5 mA Although power dissipation is internally limited electrical specifications apply only for power levels up to 25W For calculations of junction temperature rise due to power dissipation use a thermal resistance of 35 C W for the TO-3 with no heat sink With a heat sink use 2 C W for junction to case thermal resistance Note 2 Regulation is measured at constant junction temperature Changes in output voltage due to heating effects must be taken into account separately To ensure constant junction temperature pulse testing with a low duty cycle is used Note 3 Refer to RETS145K-5V for LM145K-5 0 military specifications Connection Diagram Metal Can Package Typical Applications Fixed Regulator TL H 7785 – 3 TL H 7785–2 Bottom View Order Number LM345K-5 0 See NS Package Number K02A Order Number LM145K-5 0 883 or SMD 5962-9064501 See NS Package Number K02C 2 Required for stability For value given capacitor must be solid tantalum 50 mF aluminum electrolytic may be substituted Values given may be increased without limit Required if regulator is separated from filter capacitor For value given capacitor must be solid tantulum 50 mF aluminum electrolytic may be substituted Typical Performance Characteristics Maximum Average Power Dissipation for LM145 Maximum Average Power Dissipation for LM345 Ripple Rejection Output Impedance Minimum Input-Output Voltage Differential Output Voltage vs Temperature TL H 7785 – 4 Typical Applications (Continued) TL H 7785 – 5 Select resistors to set output voltage 1 ppm C tracking suggested C1 is not needed if power supply filter capacitor is within 3 of regulator Determines zener current May be adjusted to minimize temperature drift Solid tantalum Load and line regulation k 0 01% Temperature drift k 0 001% C 3 Typical Applications (Continued) High Stability Regulator TL H 7785 – 6 C1 is not needed if power supply filter capacitor is within 3 of regulator Keep C4 within 2 of LM345 D2 sets initial output voltage accuracy The LM113 is available in b 5 b 2 and b 1% tolerance b 2V ECL Termination Regulator Dual 3 Amp Trimmed Supply Variable Output (b5 0V to b15V) TL H 7785 – 8 Optional Improves transient response and ripple rejection VOUT e b 5V  R1 a R2 R2 J TL H 7785 – 7 4 Physical Dimensions inches (millimeters) Metal Can Package (K) Order Number LM345K-5 0 NS Package Number K02A 5 LM145 LM345 Negative Three Amp Regulator Physical Dimensions inches (millimeters) (Continued) Metal Can Package (K) Mil-Aero Products Order Number LM145K-5 0 883 or SMD 5962-9064501 NS Package Number K02C LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION As used herein 1 Life support devices or systems are devices or systems which (a) are intended for surgical implant into the body or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user National Semiconductor Corporation 1111 West Bardin Road Arlington TX 76017 Tel 1(800) 272-9959 Fax 1(800) 737-7018 2 A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness National Semiconductor Europe Fax (a49) 0-180-530 85 86 Email cnjwge tevm2 nsc com Deutsch Tel (a49) 0-180-530 85 85 English Tel (a49) 0-180-532 78 32 Fran ais Tel (a49) 0-180-532 93 58 Italiano Tel (a49) 0-180-534 16 80 National Semiconductor Hong Kong Ltd 13th Floor Straight Block Ocean Centre 5 Canton Rd Tsimshatsui Kowloon Hong Kong Tel (852) 2737-1600 Fax (852) 2736-9960 National Semiconductor Japan Ltd Tel 81-043-299-2309 Fax 81-043-299-2408 National does not assume any responsibility for use of any circuitry described no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications