LM3820N

LM3820 AM Radio System February 1989 LM3820 AM Radio System General Description The LM3820 is a 3-stage AM radio IC consisting of an RF amplifier oscillator mixer IF amplifier AGC detector and zener regulator The device was originally designed for use in slug-tuned auto radio applications but is also suitable for capacitortuned portable radios The LM3820 is an improved replacement for the LM1820 Features Y Y Y Y Y Y Y Y Input protection diodes Good control on sensitivity Improved S N and tweet Versatile building-block approach Gain-controlled RF stage Cascode IF amplifier Regulated supply Pin compatible with LM1820 Connection Diagram Dual-In-Line Package TL H 7967 – 1 Order Number LM3820N See NS Package Number N14A Circuit Schematic TL H 7967 – 2 C1995 National Semiconductor Corporation TL H 7967 RRD-B30M115 Printed in U S A Absolute Maximum Ratings If Military Aerospace specified devices are required please contact the National Semiconductor Sales Office Distributors for availability and specifications Power Dissipation (Note 1) Supply Voltage 1200 mW 16V Current into Supply Terminal (Pin 3) Operating Temperature Range Storage Temperature Range Lead Temperature (Soldering 10 sec ) 35 mA b 25 C to a 85 C b 65 C to a 150 C 260 C Electrical Characteristics (Figure 1 Symbol IS VZ Parameter Supply Current Internal Zener Voltage Input Sensitivity TA e 25 C VS e 6V unless noted) Conditions Min 12 70 Typ 18 75 Max 24 80 Units mA V No RF Input f e 1 MHz 30% Mod 400 Hz Measure RF Input Level for 10 mV Audio Output with Tuning Peaked f e 1 MHz 30% Mod 1 kHz (S a N) N at Audio Output with 100 mV RF Input f e 1 MHz 90% Mod 1 kHz THD at Audio Output with 30 mV RF Input 15 35 70 mV Signal to Noise Ratio 22 28 dB Overload Distortion 6 10 % Note 1 Above TA e 25 C derate based on TJ(Max) e 150 C and iJA e 100 C W Typical Applications 100 mV RF INPUT is equivalent to approx 1 mV meter field strength See Applications Information for coil specifications TL H 7967 – 3 FIGURE 1 Capacitor-Tuned Test Fixture 2 Applications Information The circuit shown in Figure 1 is recommended as a starting point for portable radio designs Loopstick antenna L1 is used in place of L0 and the RF amplifier is used with a resistor load to drive the mixer A double tuned circuit at the output of the mixer provides selectivity while the remainder of the gain is provided by the IF section which is matched to the diode through a unity turns ratio transformer RAGC may be used in place of CAGC to bypass the internal AGC detector and provide more recovered audio An AM automobile radio design is shown in Figure 2 Tuning of both the input and the output of the RF amplifier and the mixer is accomplished with variable inductors Better selectivity is obtained through the use of double tuned interstage transformers Input circuits are inductively tuned to prevent microphonics and provide a linear tuning motion to facilitate push-button operation Coil specifications for Figure 1 are as follows TL H 7967 – 4 PCB Layout for Figure 1 Circuit TL H 7967 – 5 3 Applications Information (Continued) TRANSFORMERS T1 C e 130 pF primary secondary primary to secondary tap ratio 30 1 Q e 60 coupling critical T2 C e 130 pF primary secondary primary tap ratio 8 5 1 secondary tap ratio 8 5 1 Q e 60 coupling critical TL H 7967 – 6 FIGURE 2 Slug-Tuned Auto Radio Schematic Reference L0 L2 T1 T2 T3 Toko America 1250 Feehanville Drive Mount Prospect IL 60056 (312) 297-0070 Toko Part Number RWO-6A6255 RRC-3A6426N RRC-3A6427A RZC-1A6425A FIGURE 3 Representative Part Numbers for the Coils of Figure 1 4 5 LM3820 AM Radio System Physical Dimensions inches (millimeters) Molded Dual-In-Line Package (N) Order Number LM3820N NS Package Number N14A LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION As used herein 1 Life support devices or systems are devices or systems which (a) are intended for surgical implant into the body or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user National Semiconductor Corporation 1111 West Bardin Road Arlington TX 76017 Tel 1(800) 272-9959 Fax 1(800) 737-7018 2 A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness National Semiconductor Europe Fax (a49) 0-180-530 85 86 Email cnjwge tevm2 nsc com Deutsch Tel (a49) 0-180-530 85 85 English Tel (a49) 0-180-532 78 32 Fran ais Tel (a49) 0-180-532 93 58 Italiano Tel (a49) 0-180-534 16 80 National Semiconductor Hong Kong Ltd 13th Floor Straight Block Ocean Centre 5 Canton Rd Tsimshatsui Kowloon Hong Kong Tel (852) 2737-1600 Fax (852) 2736-9960 National Semiconductor Japan Ltd Tel 81-043-299-2309 Fax 81-043-299-2408 National does not assume any responsibility for use of any circuitry described no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications