LM3909N

LM3909 LED Flasher Oscillator February 1995 LM3909 LED Flasher Oscillator General Description The LM3909 is a monolithic oscillator specifically designed to flash Light Emitting Diodes By using the timing capacitor for voltage boost it delivers pulses of 2 or more volts to the LED while operating on a supply of 1 5V or less The circuit is inherently self-starting and requires addition of only a battery and capacitor to function as an LED flasher Packaged in an 8-lead plastic mini-DIP the LM3909 will operate over the extended consumer temperature range of b 25 C to a 70 C It has been optimized for low power drain and operation from weak batteries so that continuous operation life exceeds that expected from battery rating Application is made simple by inclusion of internal timing resistors and an internal LED current limit resistor As shown in the first two application circuits the timing resistors supplied are optimized for nominal flashing rates and minimum power drain at 1 5V and 3V Timing capacitors will generally be of the electrolytic type and a small 3V rated part will be suitable for any LED flasher using a supply up to 6V However when picking flash rates it should be remembered that some electrolytics have very broad capacitance tolerances for example b20% to a 100% Features Y Y Y Y Y Y Y Y Operation over one year from one C size flashlight cell Bright high current LED pulse Minimum external parts Low cost Low voltage operation from just over 1V to 5V Low current drain averages under 0 5 mA during battery life Powerful as an oscillator directly drives an 8X speaker Wide temperature range Applications Y Y Y Y Y Y Y Finding flashlights in the dark or locating boat mooring floats Sales and advertising gimmicks Emergency locators for instance on fire extinguishers Toys and novelties Electronic applications such as trigger and sawtooth generators Siren for toy fire engine (combined oscillator speaker driver) Warning indicators powered by 1 4V to 200V Schematic Diagram Typical 1 5V Flasher Connection Diagram Dual-In-Line Package TL H 7969 – 2 Top View Order Number LM3909N See NS Package Number N08E TL H 7969 – 1 C1995 National Semiconductor Corporation TL H 7969 RRD-B30M115 Printed in U S A Absolute Maximum Ratings If Military Aerospace specified devices are required please contact the National Semiconductor Sales Office Distributors for availability and specifications Power Dissipation V a Voltage 500 mW 6 4V Operating Temperature Range Lead Temperature (Soldering 10 sec ) b 25 C to a 70 C 260 C Electrical Characteristics Parameter Supply Voltage Operating Current Flash Frequency High Flash Frequency Compatible LED Forward Drop Peak LED Current Pulse Width 300 mF 5% Capacitor 0 30 mF 5% Capacitor 1 mA Forward Current 350 mF Capacitor 350 mF Capacitors at Amplitude 1 35 45 60 0 65 Conditions (Applications Note 3) (In Oscillation) Min 1 15 0 55 10 11 21 Typ Max 60 0 75 13 Units V mA Hz kHz V mA ms Typical Applications (See applications notes on following page) Triac Trigger Provides 40 mA 10 ms pulses at about 8 kHz Triac gate may be pulse transformer isolated if desired TL H 7969 – 3 2 Typical Applications (Continued)(See applications notes below) Warning Flasher High Voltage Powered Va 6V 15V 100V Typical Operating Conditions Nominal Flash Hz 2 2 17 CT 400 mF 180 mF 180 mF RS 1k 3 9k 43k 1W RFB 1 5k 1k 1k V a RANGE 5V – 25V 13V – 50V 85V – 200V TL H 7969 – 4 1 5V Flasher TL H 7969 – 6 Estimated Battery Life (Continuous 1 5V Flasher Operation) TL H 7969 – 5 Note Nominal flash rate 1 Hz Size Cell Standard AA C D 3 months 7 months 1 3 years Type Alkaline 6 months 15 months 2 6 years Note Estimates are made from our tests and manufacturers data Conditions are fresh batteries and room temperature Clad or ‘‘leak-proof’’ batteries are recommended for any application of five months or more Nickel Cadmium cells are not recommended APPLICATIONS NOTES Note 1 All capacitors shown are electrolytic unless marked otherwise Note 2 Flash rates and frequencies assume a g 5% capacitor tolerance Electrolytics may vary b 20% to a 100% of their stated value Note 3 Unless noted measurements above are made with a 1 4V supply a 25 C ambient temperature and an LED with a forward drop of 1 5V to 1 7V at 1 mA forward current Note 4 Occasionally a flasher circuit will fail to oscillate due to an LED defect that may be missed because it only reduces light output 10% or so Such LEDs can be identified by a large increase in conduction between 0 9V and 1 2V 3 Typical Applications (Continued) (See applications notes on previous page) 3V Flasher Minimum Power at 1 5V TL H 7969 – 8 TL H 7969–7 Note Nominal flash rate 1 1 Hz Average IDRAIN e 0 32 mA Note Nominal flash rate 1 Hz Average IDRAIN e 0 77 mA Fast Blinker TL H 7969 – 11 Note Winking LED inside locates light in total darkness TL H 7969–9 Note Nominal flash rate 2 6 Hz Average IDRAIN e 1 2 mA 4 Typical Applications (Continued) (See applications notes above) Flashlight Finder TL H 7969 – 10 Note LM3909 capacitor and LED are installed in a white translucent cap on the flashlight’s back end Only one contact strip (in addition to the case connection) is needed for flasher power Drawing current through the bulb simplifies wiring and causes negligible loss since bulb resistance cold is typically less than 2X 4 Parallel LEDs High Efficiency Parallel Circuit TL H 7969 – 12 TL H 7969 – 13 Note Nominal flash rate 1 3 Hz Average IDRAIN e 2 mA Note Nominal flash rate 1 5 Hz Average IDRAIN e 1 5 mA 5 Typical Applications (Continued) (See applications notes above) 1 kHz Square Wave TL H 7969 – 15 Note Output voltage through a 10k load to ground TL H 7969 – 14 ‘‘Buzz Box’’ Continuity and Coil Checker Variable Flasher TL H 7969 – 17 Note Flash rate 0 Hz–20 Hz TL H 7969 – 16 Note Differences between shorts coils and a few ohms of resistance can be heard 6 Typical Applications (Continued) (See applications notes above) LED Booster Incandescent Bulb Flasher TL H 7969 – 18 Note High efficiency 4 mA drain Continuous appearing light obtained by supplying short high current pulses (2 kHz) to LEDs with higher than battery voltage available TL H 7969 – 19 Note Flash rate 1 5 Hz Emergency Lantern Flasher TL H 7969 – 20 Note Nominal flash rate 1 5 Hz 7 LM3909 LED Flasher Oscillator Physical Dimensions inches (millimeters) Molded Dual-In-Line Package (N) Order Number LM3909N NS Package Number N08E LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION As used herein 1 Life support devices or systems are devices or systems which (a) are intended for surgical implant into the body or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user National Semiconductor Corporation 1111 West Bardin Road Arlington TX 76017 Tel 1(800) 272-9959 Fax 1(800) 737-7018 2 A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness National Semiconductor Europe Fax (a49) 0-180-530 85 86 Email cnjwge tevm2 nsc com Deutsch Tel (a49) 0-180-530 85 85 English Tel (a49) 0-180-532 78 32 Fran ais Tel (a49) 0-180-532 93 58 Italiano Tel (a49) 0-180-534 16 80 National Semiconductor Hong Kong Ltd 13th Floor Straight Block Ocean Centre 5 Canton Rd Tsimshatsui Kowloon Hong Kong Tel (852) 2737-1600 Fax (852) 2736-9960 National Semiconductor Japan Ltd Tel 81-043-299-2309 Fax 81-043-299-2408 National does not assume any responsibility for use of any circuitry described no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications