LM80CIMT-3

LM80 Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor June 2001 LM80 Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor General Description The LM80 provides 7 positive voltage inputs, temperature measurement, fan speed measurement, and hardware monitoring on an I2C™ interface. The LM80 performs WATCHDOG comparisons of all measured values and an open-drain interrupt output becomes active when any values exceed programmed limits. A Chassis Intrusion input is provided to monitor and reset an external circuit designed to latch a chassis intrusion event. The LM80 is especially suited to interface to both linear and digital temperature sensors. The 10 mV LSB and 2.56 volt input range is ideal for accepting inputs from a linear sensor such as the LM50. The BTI is used as an input from either digital or thermostat sensors such as LM75 and LM56. The LM80’s 2.8V to 5.75V supply voltage range, low supply current, and I2C interface make it ideal for a wide range of applications. These include hardware monitoring and protection applications in personal computers, electronic test equipment, and office electronics. n WATCHDOG comparison of all monitored values n Separate input to show status in Interrupt Status Register of additional external temperature sensors such as the LM56 or LM75 n I2C Serial Bus interface compatibility n Shutdown mode to minimize power consumption n Programmable RST_OUT/OS pin: RST_OUT provides a Reset output; OS provides an Interrupt Output activated by an Overtemperature Shutdown event Key Specifications j Voltage monitoring Error j Temperature Error ± 1% (max) ± 3˚C (max) 2.8V to 5.75V Operating: Shutdown: 0.2 mA typ 15 µA typ 8 Bits 0.5˚C −25˚C to +125˚C j Supply Voltage Range j Supply Current j ADC Resolution j Temperature Resolution Features Temperature sensing 7 positive voltage inputs 2 programmable fan speed monitoring inputs 10 mV LSB and 2.56V input range accepts outputs from linear temperature sensors such as the LM50 n Chassis Intrusion Detector input n n n n Applications n System Thermal and Hardware Monitoring for Servers and PCs n Office Electronics n Electronic Test Equipment and Instrumentation Typical Application DS100040-1 # Indicates Active Low (“Not”) I2C ® is a registered trademark of the Philips Corporation. © 2001 National Semiconductor Corporation DS100040 www.national.com LM80 Ordering Information Temperature Range −25˚C ≤ TA ≤ +125˚C Order Number LM80CIMT-31 LM80CIMTX-3 2 LM80CIMT-51 LM80CIMTX-52 2-Tape Connection Diagram NS Package Number Specified Power Supply Voltage 3.3V 5.0V Device Marking LM80CIMT-3 LM80CIMT-5 MTC24B MTC24B Note: 1-Rail transport media, 62 parts per rail and reel transport media, 3400 parts per reel DS100040-2 Block Diagram DS100040-3 Pin Descriptions Pin Name(s) INT_IN Pin Number 1 Number of Pins 1 Type Digital Input Description This is an active low input that propagates the INT_IN signal to the INT output of the LM80 via Interrupt Mask Register 1 Bit 7 and INT enable Bit 1 of the Configuration Register. Serial Bus bidirectional Data. Open-drain output. Serial Bus Clock. SDA SCL 2 3 1 1 Digital I/O Digital Input www.national.com 2 LM80 Pin Descriptions Pin Name(s) FAN1-FAN2 BTI Pin Number 4-5 6 (Continued) Number of Pins 2 1 Type Digital Inputs Digital Input Description 0 to V+ fan tachometer inputs. Board Temperature Interrupt driven by O.S. outputs of additional temperature sensors such as LM75. Provides internal pull-up of 10 kΩ. An active high input from an external circuit which latches a Chassis Intrusion event. This line can go high without any clamping action regardless of the powered state of the LM80. The LM80 provides an internal open drain on this line, controlled by Bit 5 of the Configuration Register, to provide a minimum 10 ms reset of this line. Internally connected to all of the digital circuitry. +3.3V or +5V V+ power. Bypass with the parallel combination of 10 µF (electrolytic or tantalum) and 0.1 µF (ceramic) bypass capacitors. Non-Maskable Interrupt (open source)/Interrupt Request (open drain). The mode is selected with Bit 5 of the Configuration Register and the output is enabled when Bit 1 of the Configuration Register is set to 1. The default state is disabled. An active low open drain output intended to drive an external P-channel power MOSFET for software power control. An active-low input that enables NAND Tree board-level connectivity testing. Refer to Section 10.0 on NAND Tree testing. Whenever NAND Tree connectivity is enabled the LM80 is also reset to its power on state. Master Reset, 5 mA driver (open drain), active low output with a 10 ms minimum pulse width. Available when enabled via Bit 4 in Configuration Register and Bit 7 of the Fan Divisor/RST_OUT/OS Register. Bit 6 of the Fan Divisor/RST_OUT/OS Register enables this output as an active low Overtemperature Shutdown (OS). Internally connected to all analog circuitry. The ground reference for all analog inputs. This pin needs to be taken to a low noise analog ground plane for optimum performance. 0V to 2.56V full scale range Analog Inputs. The lowest order bit of the Serial Bus Address. This pin functions as an output when doing a NAND Tree test. The two highest order bits of the Serial Bus Address. CI (Chassis Intrusion) 7 1 Digital I/O GND V+ (+2.8V to +5.75V) INT 8 9 1 1 GROUND POWER 10 1 Digital Output GPO (Power Switch Bypass) NTEST_IN/ RESET_IN 11 12 1 1 Digital Output Digital Input RST_OUT/OS 13 1 Digital Output GNDA 14 1 GROUND IN6-IN0 A0/NTEST_OUT A1-A2 TOTAL PINS 15-21 22 23-24 7 1 2 24 Analog Inputs Digital I/O Digital Inputs 3 www.national.com LM80 Absolute Maximum Ratings (Notes 1, 2) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Positive Supply Voltage (V+) Voltage on Any Input or Output Pin Ground Difference (GND - GNDA) Input Current at any Pin (Note 3) Package Input Current (Note 3) Maximum Junction Temperature (TJ max) ESD Susceptibility(Note 5) Human Body Model Machine Model 6.5V −0.3V to (V++0.3V) ± 300 mV ± 5 mA ± 20 mA 150˚C 2000V 125V Soldering Information MTC24B Package (Note 6) : Vapor Phase (60 seconds) Infrared (15 seconds) Storage Temperature 215˚C 235˚C −65˚C to +150˚C Operating Ratings(Notes 1, 2) Operating Temperature Range TMIN ≤ TA ≤ TMAX LM80CIMT-3, LM80CIMT-5 −25˚C ≤ TA ≤ +125˚C Specified Temperature Range TMIN ≤ TA ≤ TMAX LM80CIMT-3, LM80CIMT-5 −25˚C ≤ TA ≤ +125˚C Junction to Ambient Thermal Resistance (θJA(Note 4) ) NS Package Number: MTC24B 95˚C/W +2.8V to +5.75V Supply Voltage (V+) Ground Difference (|GND − GNDA|) ≤ 100 mV −0.05V to V+ + 0.05V VIN Voltage Range: DC Electrical Characteristics The following specifications apply for +2.8 VDC ≤V+ ≤ +3.8 VDC for LM80CIMT-3, +4.25 VDC ≤V+ ≤ +5.75 VDC for LM80CIMT-5, IN0-IN6 RS = 25Ω, unless otherwise specified. Boldface limits apply for TA = TJ = TMIN to TMAX; all other limits TA = TJ = 25˚C.(Note 7) Symbol Parameter Conditions Typical (Note 8) POWER SUPPLY CHARACTERISTICS I+ Supply Current Interface Inactive and V+ = 5.75V Interface Inactive and V+ = 3.8V Shutdown Mode TEMPERATURE-to-DIGITAL CONVERTER CHARACTERISTICS Temperature Error Resolution ANALOG-to-DIGITAL CONVERTER CHARACTERISTICS Resolution (8 bits with full-scale at 2.56V) TUE DNL PSS tC Total Unadjusted Error Differential Non-Linearity Power Supply Sensitivity Total Monitoring Cycle Time (Note 11) 9-bit Temp resolution 12-bit Temp resolution (Note 10) 10 mV −25˚C ≤ TA ≤ +125˚C 0.2 0.18 15 2.0 1.5 mA (max) mA (max) µA Limits (Note 9) Units (Limits) ±3 0.5 ˚C (max) ˚C (min) ±1 ±1 ±1 1.0 1.5 2 10 % (max) LSB (max) %/V sec (max) sec (max) kΩ (max) µA µA MULTIPLEXER/ADC INPUT CHARACTERISTICS On Resistance Input Current (On Channel Leakage Current) Off Channel Leakage Current 0.5 ±1 ±1 www.national.com 4 LM80 DC Electrical Characteristics (Continued) The following specifications apply for +2.8 VDC ≤V+ ≤ +3.8 VDC for LM80CIMT-3, +4.25 VDC ≤V+ ≤ +5.75 VDC for LM80CIMT-5, IN0-IN6 RS = 25Ω, unless otherwise specified. Boldface limits apply for TA = TJ = TMIN to TMAX; all other limits TA = TJ = 25˚C.(Note 7) Symbol Parameter Conditions Typical (Note 8) FAN RPM-to-DIGITAL CONVERTER Fan RPM Error +25˚C ≤ TA ≤ +75˚C −10˚C ≤ TA ≤ +100˚C −25˚C ≤ TA ≤ +125˚C Full-scale Count FAN1 and FAN2 Nominal Input RPM (See Section 6.0) Divisor = 1, Fan Count = 153 (Note 12) Divisor = 2, Fan Count = 153 (Note 12) Divisor = 3, Fan Count = 153 (Note 12) Divisor = 4, Fan Count = 153 (Note 12) Internal Clock Frequency +25˚C ≤ TA ≤ +75˚C −10˚C ≤ TA ≤ +100˚C 8800 4400 2200 1100 22.5 22.5 20.2 24.8 19.1 25.9 −25˚C ≤ TA ≤ +125˚C DIGITAL OUTPUTS: A0/NTEST_OUT, INT VOUT(1) Logical “1” Output Voltage IOUT = +5.0 mA at V+ = +4.25V, IOUT = +3.0 mA at V+ = +2.8V IOUT = −5.0 mA at V+ = +5.75V, IOUT = −3.0 mA at V+ = +3.8V IOUT =− 5.0 mA at V+ = +5.75V, IOUT = −3.0 mA at V+ = +3.8V VOUT = V+ 0.1 30 2.4 V (min) 22.5 18 27 Limits (Note 9) Units (Limits) % (max) % (max) % (max) (max) RPM RPM RPM RPM kHz (min) kHz (max) kHz (min) kHz (max) kHz (min) kHz (max) ± 10 ± 15 ± 20 255 VOUT(0) Logical “0” Output Voltage 0.4 V (max) OPEN DRAIN OUTPUTS: GPO, RST_OUT/OS, CI VOUT(0) Logical “0” Output Voltage 0.4 V (min) IOH High Level Output Current RST_OUT/OS, CI Pulse Width 100 10 µA (max) ms (min) OPEN DRAIN SERIAL BUS OUTPUT: SDA VOUT(0) Logical “0” Output Voltage IOUT = −3.0 mA at + V = +5.75V, IOUT = −3.0 mA at V+ = +3.8V VOUT = V+ 0.1 0.4 V (min) IOH VIN(1) VIN(0) VIN(1) VIN(0) IIN(1) IIN(0) CIN High Level Output Current Logical “1” Input Voltage Logical “0” Input Voltage Logical “1” Input Voltage Logical “0” Input Voltage Logical “1” Input Current Logical “0” Input Current Digital Input Capacitance 100 2.0 0.8 0.7 x V+ 0.3 x V+ µA (max) V (min) V (max) V (min) V (max) µA (min) µA (max) pF www.national.com DIGITAL INPUTS: A0/NTEST_Out, A1-A2, BTI, CI (Chassis Intrusion), INT_IN, and NTEST_IN/Reset_IN SERIAL BUS INPUTS (SCL, SDA) and FAN TACH PULSE INPUTS (FAN1, FAN2) ALL DIGITAL INPUTS Except for BTI VIN = V+ VIN = 0 VDC −0.005 0.005 20 5 −1 1 LM80 DC Electrical Characteristics (Continued) The following specifications apply for +2.8 VDC ≤V+ ≤ +3.8 VDC for LM80CIMT-3, +4.25 VDC ≤V+ ≤ +5.75 VDC for LM80CIMT-5, IN0-IN6 RS = 25Ω, unless otherwise specified. Boldface limits apply for TA = TJ = TMIN to TMAX; all other limits TA = TJ = 25˚C.(Note 7) Symbol BTI Digital Input IIN(1) IIN(0) CIN Logical “1” Input Current Logical “0” Input Current Digital Input Capacitance VIN = V+ VIN = 0 VDC −1 500 20 −10 2000 µA (min) µA (max) pF Parameter Conditions Typical (Note 8) Limits (Note 9) Units (Limits) AC Electrical Characteristics The following specifications apply for +2.8 VDC ≤V+ ≤ +3.8 VDC for LM80CIMT-3, +4.25 VDC ≤V+ ≤ +5.75 VDC for LM80CIMT-5, unless otherwise specified. Boldface limits apply for TA = TJ = TMIN to TMAX; all other limits TA = TJ = 25˚C. (Note 13) Symbol Parameter Conditions Typical (Note 8) SERIAL BUS TIMING CHARACTERISTICS t1 t2 t3 t4 t5 SCL (Clock) Period Data In Setup Time to SCL High Data Out Stable After SCL Low SDA Low Setup Time to SCL Low (start) SDA High Hold Time After SCL High (stop) 2.5 100 0 100 100 µs (min) ns (min) ns (min) ns (min) ns (min) Limits (Note 9) Units (Limits) DS100040-4 FIGURE 1. Serial Bus Timing Diagram www.national.com 6 LM80 AC Electrical Characteristics (Continued) Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. Note 2: All voltages are measured with respect to GND, unless otherwise specified Note 3: When the input voltage (VIN) at any pin exceeds the power supplies (VIN < (GND or GNDA) or VIN > V +), the current at that pin should be limited to 5 mA. The 20 mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of 5 mA to four. Note 4: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJmax, θJA and the ambient temperature, TA. The maximum allowable power dissipation at any temperature is PD = (TJmax−T A)/θJA. Note 5: The human body model is a 100 pF capacitor discharged through a 1.5 kΩ resistor into each pin. The machine model is a 200 pF capacitor discharged directly into each pin. Note 6: See the section titled “Surface Mount” found in any post 1986 National Semiconductor Linear Data Book for other methods of soldering surface mount devices. Note 7: Each input and output is protected by a nominal 6.5V breakdown voltage zener diode to GND; as shown below, input voltage magnitude up to 0.3V above V+ or 0.3V below GND will not damage the LM80. There are parasitic diodes that exist between the inputs and the power supply rails. Errors in the ADC conversion can occur if these diodes are forward biased by more than 50 mV. As an example, if V+ is 4.50 VDC, input voltage must be ≤ 4.55 VDC, to ensure accurate conversions. DS100040-5 An x indicates that the diode exists. Pin Name INT_IN CI GPO FAN1–FAN2 SCL SDA RST_OUT/OS x x FIGURE 2. ESD Protection Input Structure Note 8: Typicals are at TJ =TA =25˚C and represent most likely parametric norm. Note 9: Limits are guaranteed to National’s AOQL (Average Outgoing Quality Level). Note 10: TUE (Total Unadjusted Error) includes Offset, Gain and Linearity errors of the ADC. Note 11: Total Monitoring Cycle Time includes temperature conversion, 7 analog input voltage conversions and 2 tachometer readings. Each input voltage conversion takes 100 ms typical and 112 ms maximum. 8-plus sign Temperature resolution takes 100 ms typical and 112 ms maximum, while 11-bit plus sign takes 800 ms typical and 900 ms maximum. Fan tachometer readings take 20 ms typical, at 4400 rpm, and 200 ms max. Note 12: The total fan count is based on 2 pulses per revolution of the fan tachometer output. Note 13: Timing specifications are tested at the Serial Bus Input logic levels, VIN(0) = 0.3 x V+ for a falling edge and VIN(1) =0.7 x V+ for a rising edge. D1 x D2 x x x D3 x x x x x x Pin Name NTEST_IN/ Reset_IN IN0-IN6 BTI INT A1-A2 A0/NTEST_Out D1 D2 D3 x x x x x x x x x x x x x x x x 7 www.national.com LM80 Test Circuit DS100040-6 FIGURE 3. Digital Output Load Test Circuitry Functional Description 1.0 GENERAL DESCRIPTION The LM80 provides 7 analog inputs, a temperature sensor, a Delta-Sigma ADC (Analog-to-Digital Converter), 2 fan speed counters, WATCHDOG registers, and a variety of inputs and outputs on a single chip. A two wire Serial Bus interface is provided. The LM80 performs power supply, temperature, fan control and fan monitoring for personal computers. The LM80 continuously converts analog inputs to 8-bit digital words with a 10 mV LSB (Least Significant Bit) weighting, yielding input ranges of 0 to 2.56V. The Analog inputs are intended to be connected to the several power supplies present in a a typical computer. Temperature can be converted to a 9-bit or 12-bit two’s complement word with resolutions of 0.5˚C LSB or 0.0625˚C LSB, respectively. Fan inputs can be programmed to accept either fan failure indicator or tachometer signals. Fan failure signals can be programmed to be either active high or active low. Fan inputs measure the period of tachometer pulses from the the fans, providing a higher count for lower fan speeds. The fan inputs are digital inputs with and acceptable range of 0 to V+ volts and a transition level of approximately V+/2 volts. Full scale fan counts are 255 (8-bit counter), which represent a stopped or very slow fan. Nominal speed based on a count of 153, are programmable from 1100 to 8800 RPM. Signal conditioning circuitry is included to accommodate slow rise and fall times. The LM80 provides a number of internal registers, as detailed in Figure 4. These include: Configuration Register: Provides control and configuration. Interrupt Status Registers: Two registers to provide status of each WATCHDOG limit or Interrupt event. Interrupt Mask Registers: Allows masking of individual Interrupt sources, as well as separate masking for each of both hardware Interrupt outputs. Fan Divisor/RST_OUT/OS Registers: Bits 0-5 of this register contain the divisor bits for FAN1 and FAN2 inputs. Bits 6-7 control the function of the RST_OUT/OS output. OS Configuration/Temperature Resolution Register: The configuration of the OS (Overtemperature Shutdown) is controlled by the lower 3 bits of this register. Bit 3 enables 12-bit temperature conversions. Bits 4-7 reflect the lower four bits of the temperature reading for a 12-bit resolution. Value RAM: The monitoring results: temperature, voltages, fan counts, and Fan Divisor/RST_OUT/OS Register limits are all contained in the Value RAM. The Value RAM consists of a total of 32 bytes. The first 10 bytes are all of the results, the next 20 bytes are the Fan Divisor/RST_OUT/OS Register limits, and are located at 20h-3Fh, including two unused bytes in the upper locations. When the LM80 is started, it cycles through each measurement in sequence, and it continuously loops through the sequence approximately once every second. Each measured value is compared to values stored in WATCHDOG, or Limit registers. When the measured value violates the programmed limit the LM80 will set a corresponding Interrupt in the Interrupt Status Registers. Two hardware Interrupt lines, INT and RST_OUT/OS are available. INT is fully programmable with masking of each Interrupt source, and masking of each output. RST_OUT/OS is dedicated to the temperature reading WATCHDOG registers. In addition, the Fan Divisor register has control bits to enable or disable the hardware Interrupts. Additional digital inputs are provided for chaining of INT, outputs of multiple external LM75 temperature sensors via the BTI (Board Temperature Interrupt) input, and a CI (Chassis Intrusion) input. The Chassis Intrusion input is designed to accept an active high signal from an external circuit that latches when the case is removed from the computer. www.national.com 8 LM80 Functional Description 2.0 INTERFACE (Continued) DS100040-7 FIGURE 4. LM80 Register Structure 9 www.national.com LM80 Functional Description 2.1 Internal Registers of the LM80 (Continued) TABLE 1. The internal registers and their corresponding internal LM80 address is as follows: Register LM80 Internal Hex Address (This is the data to be written to the Address Register) 00h 01h 02h 03h 04h 05h 06h Power on Value Notes Configuration Register Interrupt Status Register 1 Interrupt Status Register 2 Interrupt Mask Register 1 Interrupt Mask Register 2 Fan Divisor/RST_OUT/OS Register OS/ Configuration and Temperature Resolution Register Value RAM 0000 1000 0000 0000 0000 0000 0000 0000 0000 0000 0001 0100 0000 0001 FAN1 and FAN2 divisor = 2 (count of 153 = 4400 RPM) 20h-3Fh www.national.com 10 LM80 Functional Description 2.2 Serial Bus Interface (Continued) DS100040-8 (a) Serial Bus Write to the Internal Address Register followed by the Data Byte DS100040-9 (b) Serial Bus Write to the Internal Address Register Only DS100040-10 (c) Serial Bus Read from a Register with the Internal Address Register Preset to Desired Location FIGURE 5. Serial Bus Timing The Serial Bus control lines consists of the SDA (serial data), SCL (serial clock) and A0-A1 (address) pins. The LM80 can only operate as a slave. The SCL line only controls the serial interface, all other clock functions within LM80 such as the ADC and fan counters are done with a separate asynchronous internal clock. When using the Serial Bus Interface a write will always consist of the LM80 Serial Bus Interface Address byte, followed by the Internal Address Register byte, then the data byte. There are two cases for a read: 1. If the Internal Address Register is known to be at the desired Address, simply read the LM80 with the Serial Bus Interface Address byte, followed by the data byte read from the LM80. 2. If the Internal Address Register value is unknown, write to the LM80 with the Serial Bus Interface Address byte, followed by the Internal Address Register byte. Then restart the Serial Communication with a Read consisting of the Serial Bus Interface Address byte, followed by the data byte read from the LM80. The default power on Serial Bus address for the LM80 is: 0101(A2)(A1)(A0) binary, where A0-A2 reflect the state of the pins defined by the same names. All of these communications are depicted in the Serial Bus Interface Timing Diagrams as shown in Figure 5. 11 www.national.com LM80 Functional Description 3.0 USING THE LM80 (Continued) Bit 3 clears the INT output when taken high. The LM80 monitoring function will stop until bit 3 is taken low. The content of the Interrupt (INT) Status Registers will not be affected. Bit4, when taken high, will initiate a 10 ms RESET signal on the RST_OUT/OS output (when this pin is in the RST mode). When bit 5 is taken high the CI (Chassis Intrusion) pin is reset. Bit 6 of the configuration register sets or clears the GPO output. This pin can be used in software power control by activating an external power control MOSFET. 3.4 Starting Conversions 3.4 STARTING CONVERSION The monitoring function (Analog inputs, temperature, and fan speeds) in the LM80 is started by writing to the Configuration Register and setting INT_Clear (Bit 3), low, and Start (Bit 0), high. The LM80 then performs a round-robin monitoring of all analog inputs, temperature, and fan speed inputs approximately once a second. If the temperature resolution is set to 12 bits one complete monitoring function will take approximately 2 seconds. The sequence of items being monitored corresponds to locations in the Value RAM (except for the Temperature reading) and is: 1. Temperature 2. IN0 3. IN1 4. IN2 5. IN3 6. IN4 7. IN5 8. IN6 9. Fan 1 10. Fan 2 3.5 Reading Conversion Results The conversion results are available in the Value RAM. Conversions can be read at any time and will provide the result of the last conversion. Because the ADC stops, and starts a new conversion whenever the conversion is read, reads of any single value should not be done more often than once every 120 ms. When reading all values with the temperature resolution set to 9-bits, allow at least 1.5 seconds between reading groups of values. Reading more frequently than once every 1.5 seconds can also prevent complete updates of Interrupt Status Registers and Interrupt Outputs. If the temperature resolution is set to 12-bit, allow at least 2.0 seconds between reading groups of values. A typical sequence of events upon power on of the LM80 would consist of: 1. Set WATCHDOG Limits 2. Set Interrupt Masks 3. Start the LM80 monitoring process 4.0 ANALOG INPUTS The 8-bit ADC has a 10 mV LSB, yielding a 0V to 2.55V (2.56 - 1LSB) input range. This is true for all analog inputs. In PC monitoring applications these inputs would most often be connected to power supplies. The 2.5, 3.3, ± 5 and ± 12 volt inputs should be attenuated with external resistors to any desired value within the input range. Care should be taken not to exceed the power supply voltage (V+) at any time. 3.1 Power On When power is first applied, the LM80 performs a “power on reset” on several of its registers. The power on condition of registers is shown in Table 1. Registers whose power on values are not shown have power on conditions that are indeterminate (this includes the value RAM and WATCHDOG limits). The ADC is inactive. In most applications, usually the first action after power on would be to write WATCHDOG limits into the Value RAM. 3.2 Resets Configuration Register INITIALIZATION accomplishes the same function as power on reset. The Value RAM conversion results, and Value RAM WATCHDOG limits are not Reset and will be indeterminate immediately after power on. If the Value RAM contains valid conversion results and/or Value RAM WATCHDOG limits have been previously set, they will not be affected by a Configuration Register INITIALIZATION. Power on reset, or Configuration Register INITIALIZATION, clear or initialize the following registers (the initialized values are shown in Table 1): Configuration Register Interrupt Status Register 1 Interrupt Status Register 2 Interrupt Mask Register 1 Interrupt Mask Register 2 Fan Divisor/RST_OUT/OS Register OS Configuration/Temperature Resolution Register Value Ram (Registers at Address 20h - 3Fh, which include: Temperature reading, IN0-IN6 readings, FAN1 and FAN2 readings, and WATCHDOG limits) Configuration Register INITIALIZATION is accomplished by setting Bit 7 of the Configuration Register high. This Bit automatically clears after being set. The LM80 can be reset to it’s “power on state” by taking NTEST_IN/Reset_IN pin low for at least 50 ns. 3.3 Using the Configuration Register The Configuration Register provides all control over the LM80. At power on, the ADC is stopped and INT_Clear is asserted, clearing the INT and RST_OUT/OS hardwire outputs. The Configuration Register starts and stops the LM80, enables and disables INT outputs, clears and sets CI and GPO I/O pins, initiates reset pulse on RST_OUT/OS pin, and provides the Reset function described in Section 3.2. Bit 0 of the Configuration Register controls the monitoring loop of the LM80. Setting Bit 0 low stops the LM80 monitoring loop and puts the LM80 in shutdown mode, reducing power consumption. Serial Bus communication is possible with any register in the LM80 although activity on these lines will increase shutdown current, up to as much as maximum rated supply current, while the activity takes place. Taking Bit 0 high starts the monitoring loop, described in more detail subsequently. Bit 1 of the Configuration Register enables the INT Interrupt hardwire output when this bit is taken high. Bit 2 of the Configuration Register defines whether the INT pin is open source or open drain. www.national.com 12 LM80 Functional Description (Continued) 5.0 LAYOUT AND GROUNDING Analog inputs will provide best accuracy when referred to the AGND pin or a supply with low noise. A separate, low-impedance ground plane for analog ground, which provides a ground point for the voltage dividers and analog components, will provide best performance but is not mandatory. Analog components such as voltage dividers should be located physically as close as possible to the LM80. The power supply bypass, the parallel combination of 10 µF (electrolytic or tantalum) and 0.1 µF (ceramic) bypass capacitors connected between pin 9 and ground, should also be located as close as possible to the LM80. A typical application, such as is shown in Figure 6, might select the input voltage divider to provide 1.9V at the analog inputs of the LM80. This is sufficiently high for good resolution of the voltage, yet leaves headroom for upward excursions from the supply of about 25%. To simplify the process of resistor selection, set the value of R2 first. Select a value for R2 or R4 between 10 kΩ and 100 kΩ This is low enough to avoid errors due to input leakage currents yet high enough to both protect the inputs under overdrive conditions as well as minimize loading of the source. Then select R1 or R3 to provide a 1.9V input as show in Figure 6. For positive input voltages the equation for calculating R1 is as follows: R1 = [ (VS − VIN) / VIN] R2 For negative input voltages the equation for Calculating R3 is as follows: R3 = [ (VS − VIN) / (VIN − 5V)] R4 The analog inputs have internal diodes that clamp inputs exceeding the power supply and ground. Exceeding any analog input has no detrimental effect on other channels. The input diodes will also clamp voltages appearing at the inputs of an un-powered LM80. External resistors should be included to limit input currents to the values given in the ABSOLUTE MAXIMUM RATINGS for Input Current At Any Pin. Inputs with the attenuator networks will usually meet these requirements. If it is possible for inputs without attenuators to be turned on while LM80 is powered off, additional resistors of about 10 kΩ should be added in series with the inputs to limit the input current. Voltage Measurements (VS) +2.5V +3.3V +5.0V +12V −12V −5V R1 or R3 R2 or R4 Voltage at Analog Inputs ( ADC code 190) +1.9V +1.9V +1.9V +1.9V +1.9V +1.9V 23.7 kΩ 22.1 kΩ 24 kΩ 160 kΩ 160 kΩ 36 kΩ 75 kΩ 30 kΩ 14.7 kΩ 30.1 kΩ 35.7 kΩ 16.2 kΩ DS100040-11 FIGURE 6. Input Examples. Resistor values shown in table provide approximately 1.9V at the analog inputs. 13 www.national.com LM80 Functional Description 6.0 FAN INPUTS (Continued) Inputs are provided for signals from fans equipped with tachometer outputs. These are logic-level inputs with an approximate threshold of V+/2. Signal conditioning in the LM80 accommodates the slow rise and fall times typical of fan tachometer outputs. The maximum input signal range is 0 to V+. In the event these inputs are supplied from fan outputs which exceed 0 to V+, either resistive division or diode clamping must be included to keep inputs within an acceptable range, as shown in Figure 7. R2 is selected so that it does not develop excessive error voltage due to input leakage. R1 is selected based on R2 to provide a minimum input of 2V and a maximum of V+. R1 should be as low as possible to provide the maximum possible input up to V+ for best noise immunity. Alternatively, use a shunt reference or zener diode to clamp the input level. If fans can be powered while the power to the LM80 is off, the LM80 inputs will provide diode clamping. Limit input current to the Input Current at Any Pin specification shown in the ABSOLUTE MAXIMUM RATINGS section. In most cases, open collector outputs with pull-up resistors inherently limit this current. If this maximum current could be exceeded, either a larger pull up resistor should be used or resistors connected in series with the fan inputs. The Fan Inputs gate an internal 22.5 kHz oscillator for one period of the Fan signal into an 8-bit counter (maximum count = 255). The default divisor, located in the VID/Fan Divisor Register, is set to 2 (choices are 1, 2, 4, and 8) providing a nominal count of 153 for a 4400 rpm fan with two pulses per revolution. Typical practice is to consider 70% of normal RPM a fan failure, at which point the count will be 219. Determine the fan count according to: Note that Fan 1 and Fan 2 Divisors are programmable via the Fan Divisor/RST_OUT/OS Register. FAN1 and FAN2 inputs can also be programmed to be level sensitive digital inputs. Fans that provide only one pulse per revolution would require a divisor set twice as high as fans that provide two pulses, thus maintaining a nominal fan count of 153. Therefore the divisor should be set to 4 for a fan that provides 1 pulse per revolution with a nominal RPM of 4400. www.national.com 14 LM80 Functional Description (Continued) DS100040-12 (a) Fan with Tach Pull-Up to +5V DS100040-13 (b) Fan with Tach Pull-Up to +12V, or Totem-Pole Output and Resistor Attenuator DS100040-14 DS100040-15 (c) Fan with Tach Pull-Up to +12V and Diode Clamp (d) Fan with Strong Tach Pull-Up or Totem Pole Output and Diode Clamp FIGURE 7. Alternatives for Fan Inputs Counts are based on 2 pulses per revolution tachometer outputs. RPM 4400 3080 2640 Time per Revolution 13.64 ms 19.48 ms 22.73 ms Counts for “Divide by 2” (Default) in Decimal 153 counts 219 counts 255 counts (maximum counts) Mode Select Nominal RPM 8800 4400 2200 1100 Time per Revolution Counts for the Given Speed in Decimal Divide by 1 Divide by 2 Divide by 4 Divide by 8 6.82 ms 13.64 ms 27.27 ms 54.54 ms 153 153 153 153 6160 3080 1540 770 70% RPM Time per Revolution for 70% RPM 9.74 ms 19.48 ms 38.96 ms 77.92 ms Typical RPM 70% RPM 60% RPM Comments 15 www.national.com LM80 Functional Description (Continued) 7.1 Temperature Data Format Temperature data can be read from the Temperature, Thot, Thot hyst, Tos and Tos hyst setpoint registers; and written to the Thot, Thot hyst, Tos and Tos hyst setpoint registers. Thot set point, Thot hyst set point, Tos set point and Tos hyst temperature data is represented by an 8-bit, two’s complement word with an LSB (Least Significant Bit) equal to 1˚C: Temperature +125˚C +25˚C +1.0˚C +0˚C −1.0˚C −25˚C −55˚C Digital Output Binary 0111 1101 0001 1001 0000 0001 0000 0000 1111 1111 1110 0111 1100 1001 Hex 7Dh 19h 01h 00h FFh E7h C9h 7.0 TEMPERATURE MEASUREMENT SYSTEM The LM80 bandgap type temperature sensor and ADC perform 9-bit or a 12-bit two’s-complement conversions of the temperature. An 8-bit digital comparator is also incorporated that compares the readings to the user-programmable Hot and Overtemperature setpoints, and Hysteresis values. DS100040-20 (Non-Linear Scale for Clarity) FIGURE 8. 9-bit Temperature-to-Digital Transfer Function DS100040-16 (Non-Linear Scale for Clarity) FIGURE 9. 12-bit Temperature-to-Digital Transfer Function www.national.com 16 LM80 Functional Description (Continued) By default Temperature Register data is represented by a 9-bit two’s complement digital word with the LSB having a resolution of 0.5˚C: Temperature +125˚C +25˚C +1.5˚C +0˚C −0.5˚C −25˚C −55˚C Digital Output Binary 0 1111 1010 0 0011 0010 0 0000 0011 0 0000 0000 1 1111 1111 1 1100 1110 1 1001 0010 Hex 0 FAh 0 32h 0 03h 0 00h 1 FFh 1 CEh 1 92h Temperature Register data can also be represented by a 12-bit two’s complement digital word with a LSB of 0.0625˚C: Temperature +125˚C +25˚C +1.0˚C +0.0625˚C 0˚C −0.0625˚C −1.0˚C −25˚C −55˚C Digital Output Binary 0111 1100 0000 0001 1001 0000 0000 0001 0000 0000 0000 0001 0000 0000 0000 1111 1111 1111 1111 1111 0000 1110 0111 0000 1100 1001 0000 Hex 7 D0h 1 90h 0 10h 0 01h 00h F FFh F F0h E 70h C 90h 7.2 Temperature Interrupts There are four Value RAM WATCHDOG limits for the Temperature reading that affect the INT and OS outputs of the LM80. They are: Hot Temperature Limit, Hot Temperature Hysteresis Limit, OS Limit, OS Hysteresis Limit. There are three interrupt modes of operation: “One-Time Interrupt” mode, “Default Interrupt” mode, and “Comparator Mode”. The OS output of the LM80 can be programmed for “One-Time Interrupt” mode and “Comparator” mode. INT can be programmed for “Default Interrupt” mode and “One-Time” Interrupt. “Default Interrupt mode” operates in the following way: Exceeding Thot causes an Interrupt that will remain active indefinitely until reset by reading Interrupt Status Register 1 or cleared by the INT_Clear bit in the Configuration register. Once an Interrupt event has occurred by crossing Thot, then reset, an Interrupt will occur again once the next temperature conversion has completed. The interrupts will continue to occur in this manner until the temperature goes below Thot hyst, at which time the Interrupt output will automatically clear. “One-Time Interrupt” mode operates in the following way: Exceeding Thot causes an Interrupt that will remain active indefinitely until reset by reading Interrupt Status Register 1 or cleared by the INT_Clear bit in the Configuration register. Once an Interrupt event has occurred by crossing Thot, then reset, an Interrupt will not occur again until the temperature goes below Thot hyst. “Comparator” mode operates in the following way: Exceeding Tos causes the OS output to go Low (default). OS will remain Low until the temperature goes below Tos. Once the temperature goes below Tos, OS will go High. The 8 MSBs of the Temperature reading can be found at Value RAM address 28 h. The remainder of the Temperature reading can be found in the OS Configuration/Temperature Resolution Register bits 7-4. In 9-bit format bit 7 is the only valid bit. 17 www.national.com LM80 www.national.com DS100040-17 Functional Description (Continued) 18 Temperature Interrupt Response Diagram. This diagram does not reflect all the possible variations in the operation of the OS and INT outputs nor the OS and Hot Temp bits. The interrupt outputs are cleared by reading the appropriate Interrupt Status Register. LM80 Functional Description (Continued) 8.0 THE LM80 INTERRUPT STRUCTURE DS100040-18 FIGURE 10. Interrupt Structure Figure 10 depicts the Interrupt Structure of the LM80. The LM80 can generate Interrupts as a result of each of its internal WATCHDOG registers on the analog, temperature, and fan inputs. 8.1 INTERRUPT INPUTS External Interrupts can come from the following sources. While the label suggests a specific type or source of Interrupt, this label is not a restriction of its usage, and it could come from any desired source: • • BTI - This is an active low Interrupt intended to come from the O.S. output of LM75 temperature sensors. The LM75 O.S. output goes active when its temperature exceeds a programmed threshold. Up to 8 LM75’s can be connected to a single Serial Bus bus with their O.S. output’s wire or’d to the BTI input of the LM80. If the temperature of any LM75 exceeds its programmed limit, it drives BTI low. This generates an Interrupt to notify the host of a possible overtemperature condition. Provides an internal pull-up of 10 kΩ. 19 CI (Chassis Intrusion) - This is an active high interrupt from any type of device that detects and captures chassis intrusion violations. This could be accomplished mechanically, optically, or electrically, and circuitry external to the LM80 is expected to latch the event. The design of the LM80 allows this input to go high even with no power applied to the LM80, and no clamping or other interference with the line will occur. This line can also be pulled low for at least 10 ms by the LM80 to reset a typical Chassis Intrusion circuit. Accomplish this reset by setting Bit 5 of Configuration Register high. The bit in the Register is self-clearing. www.national.com LM80 Functional Description • (Continued) INT_IN - This active low Interrupt merely provides a way to chain the INT (Interrupt) from other devices through the LM80 to the processor. 8.2 INTERRUPT OUTPUTS All Interrupts are indicated in the two Interrupt Status Registers. INT output has two mask registers, and individual masks for each Interrupt. As described in Section 3.3, this hardware Interrupt line can also be enabled/disabled in the Configuration Register. The Configuration Register is also used to set the mode of the INT Interrupt line. OS is dedicated to the Temperature reading WATCHDOG. In the “Fan Divisor/RST_OUT/OS Register” the OS enable bit (Bit-6), must be set high and the RST enable bit (Bit -7) must be set low to enable the OS function on the RST_OUT/OS pin. OS pin has two modes of operation: “One-Time Interrupt” and “Comparator”. “One-Time Interrupt” mode is selected by taking bit-2 of the “OS Configuration/Temperature Resolution Register” high. If bit-2 is taken low “Comparator” mode is selected. Unlike the OS pin, the OS bit in “Interrupt Status Register 2” functions in “Default Interrupt” and “One-Time Interrupt” modes. The OS bit can be masked to INT pin by taking bit-5 in the “Interrupt Mask Register 2” low. A description of “Comparator”, “Default Interrupt” and “One-Time Interrupt” modes can be found in Section 7.1. 8.3 INTERRUPT CLEARING Reading an Interrupt Status Register will output the contents of the Register, and reset the Register. A subsequent read done before the analog “round-robin” monitoring loop is complete will indicate a cleared Register. Allow at least 1.5 seconds to allow all Registers to be updated between reads. In summary, the Interrupt Status Register clears upon being read, and requires at least 1.5 seconds to be updated. When the Interrupt Status Register clears, the hardwire interrupt line will also clear until the Registers are updated by the monitoring loop. The hardware Interrupt lines are cleared with the INT_Clear bit, which is Bit 3 of the Configuration Register, without affecting the contents of the Interrupt (INT) Status Registers. When this bit is high, the LM80 monitoring loop will stop. It will resume when the bit is low. 9.0 RST and GPO OUTPUTS In PC applications the open drain GPO provides a gate drive signal to an external P-channel MOSFET power switch. This external MOSFET then would keep power turned on regardless of the state of front panel power switches when software power control is used. In any given application this signal is not limited to the function described by its label. For example, since the LM80 incorporates temperature sensing, the GPO output could also be utilized to control power to a cooling fan. Take GPO active low by setting Bit 6 in the Configuration Register low. RST is intended to provide a master reset to devices connected to this line. The RST_OUT/OS Control bit in Fan Divisor/RST_OUT/OS Register, Bit 7, must be set high to enable this function. Setting Bit 4 in the Configuration Register high outputs a least 10 ms low on this line, at the end of which Bit 4 in the Configuration Register automatically clears. Again, the label for this pin is only its suggested use. In applications where the RST capability is not needed it can be used for any type of digital control that requires a 10 ms active low open drain output. 10.0 NAND TREE TESTS A NAND tree is provided in the LM80 for Automated Test Equipment (ATE) board level connectivity testing. If the user applies a logic zero to the NTEST_IN/Reset_IN input pin, the device will be in the NAND tree test mode. A0/NTEST_OUT will become the NAND tree output pin. To perform a NAND tree test all pins included in the NAND tree should be driven to 1. Beginning with IN0 and working clockwise around the chip, each pin can be toggled and a resulting toggle can be observed on A0/NTEST_OUT. The following pins are excluded from the NAND tree test: GNDA (analog ground), GND (digital ground), V + (power supply), A0/NTEST_OUT, NTEST_IN/Reset_IN and RST_OUT/OS. Allow for a typical propagation delay of 500 ns. www.national.com 20 LM80 Functional Description 11.0 FAN MANUFACTURERS (Continued) Sanyo Denki America, Inc. 468 Amapola Ave. Torrance, CA 90501 310 783-5400 Model Number 109P06XXY601 109R06XXY401 Frame Size 2.36 in sq. X 0.79 in (60 mm sq. X 20 mm) 2.36 in sq. X 0.98 in (60 mm sq. X 25 mm) 109P08XXY601 109R08XXY401 3.15 in sq. X 0.79 in (80 mm sq. X 20 mm) 3.15 in sq. X 0.98 in (80 mm sq. X 25 mm) 21-42 23-30 13-28 Airflow CFM 11-15 Manufacturers of cooling fans with tachometer outputs are listed below: NMB Tech 9730 Independence Ave. Chatsworth, California 91311 818 341-3355 818 341-8207 Model Number 2408NL 2410ML 3108NL 3110KL Frame Size 2.36 in sq. X 0.79 in (60 mm sq. X 20 mm) 2.36 in sq. X 0.98 in (60 mm sq. X 25 mm) 3.15 in sq. X 0.79 in (80 mm sq. X 20 mm) 3.15 in sq. X 0.98 in (80 mm sq. X 25 mm) Mechatronics Inc. P.O. Box 20 Mercer Island, WA 98040 800 453-45698 Various sizes available with tach output option. 25-40 25-42 14-25 Airflow CFM 9-16 21 www.national.com LM80 Functional Description 12.0 REGISTERS AND RAM (Continued) 12.1 Address Register The main register is the ADDRESS Register. The bit designations are as follows: Bit 7-0 Name Address Pointer Bit 7 A7 Bit 6 A6 Read/ Write Read/Write Description Address of RAM and Registers. See the tables below for detail. Bit 4 A4 Bit 3 A3 Bit 2 A2 Bit 1 A1 Bit 0 A0 Bit 5 A5 Address Pointer (Power On default 00h) 12.2 Address Pointer Index (A7–A0) Registers and RAM A6–A0 in Hex 00h 01h 02h 03h 04h 05h 06h Power On Value of Registers: < 7:0 > in Binary Configuration Register Interrupt Status Register 1 Interrupt Status Register 2 Interrupt Mask Register 1 Interrupt Mask Register 2 Fan Divisor/RST_OUT/OS OS Configuration/Temperature Resolution Register Value RAM 0000 1000 0000 0000 0000 0000 0000 0000 0000 0000 0001 0100 0000 0001 20h–3Fh www.national.com 22 LM80 Functional Description (Continued) 12.3 Configuration Register — Address 00h Power on default < 7:0 > = 00001000 binary Bit 0 Name Start Read/ Write Read/Write Description A one enables startup of monitoring operations, a zero puts the part in standby mode. Note: The outputs of Interrupt pins will not be cleared if the user writes a zero to this location after an interrupt has occurred unlike “INT_Clear” bit.At start up, limit checking functions and scanning begin. Note, all limits should be set in the Value RAM before setting this bit HIGH. 1 2 3 INT Enable INT polarity select INT_Clear Read/Write Read/Write Read/Write A one enables the INT Interrupt output. A one selects an active high open source output while a zero selects an active low open drain output. A one disables the INT and RST_OUT/OS outputs without affecting the contents of Interrupt Status Registers. The device will stop monitoring. It will resume upon clearing of this bit. A one outputs at least a 10 ms active low reset signal at RESET, if < 7 > = 1 and < 6 > = 0 in the Fan Divisor/RST_OUT/OS Register. This bit is cleared once the pulse has gone inactive. A one clears the CI (Chassis Intrusion) pin. This bit clears itself after the CI pins cleared. A one in this bit drives a one on GPO (General Purpose Output) pin. A one restores power on default value to the Configuration Register, Interrupt Status Registers, Interrupt Mask Registers, Fan Divisor/RST_OUT/OSRegister, and the OS Configuration/Temperature Resolution Register. This bit clears itself since the power on default is zero. 4 RESET Read/Write 5 6 7 Chassis Clear GPO INITIALIZATION Read/Write Read/Write Read/Write 23 www.national.com LM80 Functional Description (Continued) 12.4 Interrupt Status Register 1 — Address 01h Power on default < 7:0 > = 0000 0000 binary Bit 0 1 2 3 4 5 6 7 Name IN0 IN1 IN2 IN3 IN4 IN5 IN6 INT_IN Read/Write Read Only Read Only Read Only Read Only Read Only Read Only Read Only Read Only Description A one indicates a High or Low limit has been exceeded. A one indicates a High or Low limit has been exceeded. A one indicates a High or Low limit has been exceeded. A one indicates a High or Low limit has been exceeded. A one indicates a High or Low limit has been exceeded. A one indicates a High or Low limit has been exceeded. A one indicates a High or Low limit has been exceeded. A one indicates that a Low has been detected on the INT_IN. 12.5 Interrupt Status Register 2 — Address 02h Power on default < 7:0 > = 0000 0000 binary Bit 0 Name Hot Temperature Read/Write Read Only Description A one indicates a High or Low limit has been exceeded. Only “One-Time Interrupt” and “Default Interrupt” modes are supported. The mode is set by bit-6 of the Interrupt Mask Register 2. A one indicates that an interrupt has occurred from the Board Temperature Interrupt (BTI) input pin. BTI can be tied to the OS output of multiple LM75 chips. A one indicates that a fan count limit has been exceeded. A one indicates that a fan count limit has been exceeded. A one indicates CI (Chassis Intrusion) has gone high. A one indicates a High or a Low OS Temperature limit has been exceed. Only “One-Time Interrupt” and “Default Interrupt” modes are supported (see Sections 7.2 and 8.2). The mode is set by bit-7 of the Interrupt Mask Register 2. 1 2 3 4 5 BTI FAN1 FAN2 CI (Chassis Intrusion) OS bit Read Only Read Only Read Only Read Only Read Only 6 7 Reserved Reserved Read Only Read Only 12.6 Interrupt Mask Register 1 — Address 03h Power on default < 7:0 > = 0000 0000 binary Bit 0 1 2 3 4 5 6 7 Name IN0 IN1 IN2 IN3 IN4 IN5 IN6 INT_IN Read/ Write Read/Write Read/Write Read/Write Read/Write Read/Write Read/Write Read/Write Read/Write Description A one disables the corresponding interrupt status bit for INT interrupt. A one disables the corresponding interrupt status bit for INT interrupt. A one disables the corresponding interrupt status bit for INT interrupt. A one disables the corresponding interrupt status bit for INT interrupt. A one disables the corresponding interrupt status bit for INT interrupt. A one disables the corresponding interrupt status bit for INT interrupt. A one disables the corresponding interrupt status bit for INT interrupt. A one disables the corresponding interrupt status bit for INT interrupt. www.national.com 24 LM80 Functional Description (Continued) 12.7 Interrupt Mask Register 2 — Address 04h Power on default < 7:0 > = 0000 0000 binary Bit 0 1 2 3 4 5 6 Name Hot Temperature BTI FAN1 FAN2 CI (Chassis Intrusion) OS bit Hot Temperature Interrupt mode select Read/ Write Read/Write Read/Write Read/Write Read/Write Read/Write Read/Write Read/Write Description A one disables the corresponding interrupt status bit for INT interrupt. A one disables the corresponding interrupt status bit for INT interrupt. A one disables the corresponding interrupt status bit for INT interrupt. A one disables the corresponding interrupt status bit for INT interrupt. A one disables the corresponding interrupt status bit for INT interrupt. A one disables the corresponding interrupt status bit for INT interrupt. A zero selects the default interrupt mode which gives the user an interrupt if the temperature goes above the hot limit. The interrupt will be cleared once the status register is read, but it will again be generated when the next conversion has completed. It will continue to do so until the temperature goes below the hysteresis limit. A one selects the one time interrupt mode which only gives the user one interrupt when it goes above the hot limit. The interrupt will be cleared once the status register is read. Another interrupt will not be generated until the temperature goes below the hysteresis limit. It will also be cleared if the status register is read. No more interrupts will be generated until the temperature goes above the hot limit again. The corresponding bit will be cleared in the status register every time it is read but may not set again when the next conversion is done. (See in Section 7.0) A zero selects the default interrupt mode which gives the user an interrupt if the temperature goes above the hot limit. The interrupt will be cleared once the status register is read, but it will again be generated when the next conversion has completed. It will continue to do so until the temperature goes below the hysteresis limit. A one selects the one time interrupt mode which only gives the user one interrupt when it goes above the hot limit. The interrupt will be cleared once the status register is read. Another interrupt will not be generated until the temperature goes below the hysteresis limit. It will also be cleared if the status register is read. No more interrupts will be generated until the temperature goes above the hot limit again. The corresponding bit will be cleared in the status register every time it is read but may not set again when the next conversion is done. (See Section in Section 7.0) 7 OS bit Interrupt mode select Read/Write 25 www.national.com LM80 Functional Description (Continued) 12.8 Fan Divisor Register/RST_OUT/OS — Address 05h Power on – < 7:4 > is 0101, and < 3:0 > is mapped to VID < 3:0 > Bit 0 1 2-3 Name FAN1 Mode Select FAN2 Mode Select FAN1 RPM Control Read/Write Read/Write Read/Write Read/Write Description A one selects the level sensitive input mode while a zero selects Fan count mode for the FAN1 input pin. A one selects the level sensitive input mode while a zero selects Fan count mode for the FAN2 input pin. FAN1 Speed Control. < 3:2 > < 3:2 > < 3:2 > < 3:2 > = 00 - divide by 1; = 01 - divide by 2; = 10 - divide by 4; = 11 - divide by 8. If level sensitive input is selected: > 2 < = 1 selects and active-low input (An interrupt will be generated if the FAN2 input is Low), > 2 < = 0 selects an active-high input (an interrupt will be generated if the FAN2 input is High). 4-5 FAN2 RPM Control Read/Write FAN2 Speed Control. < 5:4 > < 5:4 > < 5:4 > < 5:4 > = 00 - divide by 1; = 01 - divide by 2; = 10 - divide by 4; = 11 - divide by 8. If level sensitive input is selected: < 2 > = 1 selects and active-low input (An interrupt will be generated if the FAN2 input is Low), < 2 > = 0 selects an active-high input (an interrupt will be generated if the FAN2 input is High). 6 OS pin enable Read/Write A one enables OS mode on the RST_OUT/OS output pin, while Bit 7 of this register is set to zero. If bits 6 and 7 of this register are set to zero the RST_OUT/OS pin is disabled. A one sets the RST_OUT/OS pin in the RST mode. In the RST mode, bit 7 of the Fan Divisor/RST_OUT/OS Register has to be set to one. If bits 6 and 7 of this register are set to zero the RST_OUT/OS pin is disabled. 7 RST enable Read/Write 12.9 OS Configuration/Temperature Resolution Register — Address 06h Power on default Serial Bus address < 7:0 > = 0000 0001 binary Bit 0 1 2 3 Name OS status OS Polarity OS mode select Temperature Resolution Control Temp [3:0] Read/Write Read only Read/Write Read/Write Read/Write Description Status of the OS.This bit mirrors the state of the RST_OUT/OS pin when in the OS mode. A zero selects OS to be active-low, while a one selects OS to be active high. OS is an open-drain output. A one selects the one time interrupt mode for OS, while a zero selects comparator mode for OS. (See in Section 7.0) A zero selects the default 8-bit plus sign resolution temperature conversions while a one selects 11-bit plus sign resolution temperature conversions. 8-bit plus sign conversions time is approximately 100 ms, while 11-bit plus sign conversion time is approximately 2 seconds. The lower nibble (4 LSBs) of the 11-bit plus sign temperature data. < 4 > = Temp [0] (nibble LSB, 0.0625˚C), < 5 > = Temp [1], < 6 > = Temp [2], < 7 > = Temp 3 (nibble MSB, 0.5˚C). For 8-bit plus sign temperature resolution, < 7 > = Temp [0] (LSB, 0.5˚C) while < 4:6 > are undefined. 4-7 Read/Write www.national.com 26 LM80 Functional Description Address A7–A0 20h 21h 22h 23h 24h 25h 26h 27h 28h 29h 2Ah 2Bh 2Ch 2Dh 2Eh 2Fh 30h 31h 32h 33h 34h 35h 36h 37h 38h 39h 3Ah 3Bh 3Ch 3Dh 3Eh-3Fh IN0 reading IN1 reading IN2 reading IN3 reading IN4 reading IN5 reading IN6 reading (Continued) 12.10 Value RAM — Address 20h–3Fh Description Temperature reading FAN1 reading Note: This location stores the number of counts of the internal clock per revolution. FAN2 reading Note: This location stores the number of counts of the internal clock per revolution. IN0 High Limit IN0 Low Limit IN1 High Limit IN1 Low Limit IN2 High Limit IN2 Low Limit IN3 High Limit IN3 Low Limit IN4 High Limit IN4 Low Limit IN5 High Limit IN5 Low Limit IN6 High Limit IN6 Low Limit Hot Temperature Limit (High) Hot Temperature Hysteresis Limit (Low) OS Temperature Limit (High) OS Temperature Hysteresis Limit (Low) FAN1 Fan Count Limit Note: It is the number of counts of the internal clock for the Low Limit of the fan speed. FAN2 Fan Count Limit Note: It is the number of counts of the internal clock for the Low Limit of the fan speed. Reserved Note: Setting all ones to the high limits for voltages and fans (0111 1111 binary for temperature) means interrupts will never be generated except the case when voltages go below the low limits. For voltage input high limits, the device is doing a greater than comparison. For low limits, however, it is doing a less than or equal to comparison. 27 www.national.com LM80 Typical Application DS100040-19 FIGURE 11. In this PC application the LM80 monitors temperature, fan speed for 2 fans, and 7 power supply voltages. It also monitors an optical chassis intrusion detector. www.national.com 28 LM80 Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor Physical Dimensions inches (millimeters) unless otherwise noted 24-Lead Molded Plastic TSSOP Order Number LM80CIMT-3, LM80CIMTX-3, LM80CIMTX-5 or LM80CIMT-5 NS Package Number MTC24B LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Email: support@nsc.com National Semiconductor Europe Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: ap.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 www.national.com National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.