LMP7300MAX

LMP7300 Micropower Precision Comparator and Precision Reference with Adjustable Hysteresis September 2007 LMP7300 Micropower Precision Comparator and Precision Reference with Adjustable Hysteresis General Description The LMP7300 is a combination comparator and reference with ideal specifications for precision threshold detecting. The precision 2.048V reference comes with a 0.25% maximum error. The comparator features micopower (35 µW), low offset voltage (.75 mV max), and independent adjustable positive and negative hysteresis. Hysteresis control for the comparator is accomplished through two external pins. The HYSTP pin sets the positive hysteresis and the HYSTN pin sets the negative hysteresis. The comparator design isolates the VIN source impedance and the programmable hysteresis components. This isolation prevents any undesirable interaction allowing the IC to maintain a precise threshold voltage during level detection. The combination of low offset voltage, external hysteresis control, and precision voltage reference provides an easy to use micropower precision threshold detector. The LMP7300 open collector output makes it ideal for mixed voltage system designs. The output voltage upper rail is unconstrained by VCC and can be pulled above VCC to a maximum of 12V. The LMP7300 is a member of the LMP® precision amplifier family. Features (For VS = 5V, typical unless otherwise noted) 13 μA ■ Supply current 4 μs ■ Propagation delay 0.3 mV ■ Input offset voltage 100 dB ■ CMRR 100 dB ■ PSRR ■ Positive and negative hysteresis control 1 mV/mV ■ Adjustable hysteresis 2.048V ■ Reference voltage 0.25% ■ Reference voltage accuracy 1 mA ■ Reference voltage source current 2.7V to 12V ■ Wide supply voltage range ■ Operating temperature range ambient −40°C to 125°C Applications ■ ■ ■ ■ Precision threshold detection Battery monitoring Battery management systems Zero crossing detectors Typical Application Micropower Precision Battery Low Voltage Detector for 3 Cell Discharge Voltage 20175642 20175646 LMP® is a registered trademark of National Semiconductor Corporation. © 2007 National Semiconductor Corporation 201756 www.national.com LMP7300 Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. ESD Tolerance (Note 2) Junction Temperature (Note 3) Soldering Information +150°C 235°C 260°C  Infrared or Convection (20 sec)  Wave Soldering Lead Temp. (10 sec)  Human Body Model  Machine Model VIN Differential Supply Voltage (VS = V+ – V−) Voltage at Input/Output Pins Storage Temperature Range 2000V 200V ±VS 13.6V V+ + 0.3V, V− − 0.3V −65°C to +150°C (Note 4) Operating Ratings Temperature Range (Note 3) Supply Voltage (VS = V+ – V−) (Note 1) −40°C to 125°C 2.7V to 12V 166°C/W 235°C/W Package Thermal Resistance (θJA (Note 3)) 8-Pin SOIC 8-Pin MSOP 2.7V Electrical Characteristics Symbol IS Parameter Supply Current Unless otherwise specified, all limits are guaranteed for TA = 25°C, V+ = 2.7V, V− = 0V, and VCM = V+/2, RPULLUP = 100 kΩ, CLOAD = 10 pF. Boldface limits apply at the temperature extremes. Conditions RPULLUP = Open Min (Note 6) Typ (Note 5) 9 Max (Note 6) 12 17 ±0.75 ±2 3 4 0.5 Units μA Comparator VOS TCVOS IB IOS CMRR PSRR VOL ILEAK HCLIN IHYS TPD Reference VO Reference Voltage Line Regulation Load Regulation TCVREF/°C Temperature Coefficient VN Output Noise Voltage VCC = 2.7V to 12V IOUT = 0 to 1 mA −40°C to 125°C 0.1 Hz to 10 Hz 10 Hz to 10 kHz 80 100 2.043 2.048 14 0.2 2.053 80 0.5 55 V μV/V mV/mA ppm/°C μVPP μVRMS Input Offset Voltage Input Offset Average Drift Input Bias Current (Note 7) Input Offset Current Common Mode Rejection Ratio Power Supply Rejection Ratio Output Low Voltage Output Leakage Current Hysteresis Control Voltage Linearity Hysteresis Leakage Current Propagation Delay (High to Low) Overdrive = 10 mV, CL = 10 pF Overdrive = 100 mV, CL = 10 pF 1V < VCM < 2.7V V+ = 2.7V to 12V ILOAD = 10 mA Comparator Output in High State 0 < Ref-HYSTP,N < 25 mV 25 mV < Ref-HYSTP,N < 100 mV 80 80 VCM = V+/2 (Note 8) |VID| < 2.5V ±0.07 1.8 1.2 0.15 100 100 0.25 1 1.000 0.950 1.2 12 4.5 3 4 17 7.6 0.4 0.5 mV μV/°C nA nA dB dB V pA mV/V nA μs www.national.com 2 LMP7300 5V Electrical Characteristics Symbol IS Parameter Supply Current (Note 4) Unless otherwise specified, all limits are guaranteed for TA = 25°C, V+ = 5V, V− = 0V, and VCM = V+/2, RPULLUP = 100 kΩ, CLOAD = 10 pF. Boldface limits apply at the temperature extremes. Conditions RPULLUP = Open Min (Note 6) Typ (Note 5) 10 Max (Note 6) 13 18 ±0.75 ±2 3 4 0.5 Units μA Comparator VOS TCVOS IB IOS CMRR PSRR VOL ILEAK HCLIN IHYS TPD Reference VO Reference Voltage Line Regulation Load Regulation TCVREF/°C VN Temperature Coefficient Output Noise Voltage VCC = 2.7V to 12V IOUT = 0 to 1 mA −40°C to 125°C 0.1 Hz to 10 Hz 10 Hz to 10 kHz 80 100 2.043 2.048 14 0.2 2.053 80 0.5 55 V μV/V mV/mA ppm/°C μVPP μVRMS Input Offset Voltage Input Offset Average Drift Input Bias Current (Note 7) Input Offset Current Common Mode Rejection Ratio Power Supply Rejection Ratio Output Voltage Low Output Leakage Current Hysteresis Control Voltage Linearity Hysteresis Leakage Current Propagation Delay (High to Low) Overdrive = 10 mV, CL = 10 pF Overdrive = 100 mV, CL = 10 pF 1 ≤ VCM ≤ 5V V+ = 2.7V to 12V ILOAD = 10 mA Comparator Output in High State 0 < Ref-VHYSTP,N < 25 mV 25 mV < Ref-VHYSTP,N < 100 mV 80 80 VCM = V+/2 (Note 8) |VID| < 2.5V ±0.07 1.8 1.2 0.15 100 100 0.25 1 1.000 0.950 1.2 12 4 3 4 15 7 0.4 mV μV/°C nA nA dB dB V pA mV/V nA μs 12V Electrical Characteristics Symbol IS Parameter Supply Current (Note 4) Unless otherwise specified, all limits are guaranteed for TA = 25°C, V+ = 12V, V− = 0V, and VCM = V+/2, RPULLUP = 100 kΩ, CLOAD = 10 pF. Boldface limits apply at the temperature extremes. Conditions RPULLUP = Open Min (Note 6) Typ (Note 5) 11 Max (Note 6) 14 20 ±0.75 ±2 3 4 0.5 Units µA Comparator VOS TCVOS IB IOS CMRR PSRR VOL ILEAK Input Offset Voltage Input Offset Average Drift Input Bias Current (Note 7) Input Offset Current Common Mode Rejection Ratio Power Supply Rejection Ratio Output Voltage Low Output Leakage Current 1V ≤ VCM ≤ 12V V+ = 2.7V to 12V ILOAD = 10 mA Comparator Output in High State 80 80 VCM = V+/2 (Note 8) |VID| > 2.5V ±0.08 1.8 1.2 0.15 100 100 0.25 1 0.4 mV μV/°C nA nA dB dB V pA 3 www.national.com LMP7300 Symbol HCLIN IHYS TPD Reference VO Parameter Hysteresis Control Voltage Linearity Hysteresis Leakage Current Propagation Delay (High to Low) Conditions 0 < Ref-V+HYSTP,N < 25 mV 25 mV < Ref-V+HYSTP,N < 100 mV Min (Note 6) Typ (Note 5) 1.000 0.950 1.2 Max (Note 6) Units mV/V 3 4 15 6.8 2.053 80 0.5 55 nA μs Overdrive = 10 mV, CL = 10 pF Overdrive = 100 mV, CL = 10 pF TJ = 25°C VCC = 2.7V to 12V IOUT = 0 to 1 mA −40°C to +125°C 0.1 Hz to 10 Hz 10 Hz to 10 kHz 2.043 11 3.5 2.048 14 0.2 80 100 Reference Voltage Line Regulation Load Regulation V μV/V mV/mA ppm/°C μVPP μVRMS TCVREF/°C VN Temperature Coefficient Output Noise Voltage Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics Tables. Note 2: Human Body Model, applicable std. MIL-STD-883, Method 3015.7. Machine Model, applicable std. JESD22-A115-A (ESD MM std. of JEDEC) Field-Induced Charge-Device Model, applicable std. JESD22-C101-C (ESD FICDM std. of JEDEC). Note 3: The maximum power dissipation is a function of TJ(MAX), θJA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(MAX) – TA)/ θJA. All numbers apply for packages soldered directly onto a PC Board. Note 4: Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very limited self-heating of the device such that TJ = TA. No guarantee of parametric performance is indicated in the electrical tables under conditions of internal self-heating where TJ > TA. Note 5: Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will also depend on the application and configuration. The typical values are not tested and are not guaranteed on shipped production material. Note 6: Limits are 100% production tested at 25°C. Limits over the operating temperature range are guaranteed through correlations using statistical quality control (SQC) method. Note 7: Positive current corresponds to current flowing into the device. Note 8: Offset voltage average drift determined by dividing the change in VOS at temperature extremes, by the total temperature change. Ordering Information Package 8-Pin SOIC 8-Pin MSOP Part Number LMP7300MA LMP7300MAX LMP7300MM LMP7300MMX Package Marking LMP7300MA C31A Transport Media 95 Units/Rail 2.5k Units Tape and Reel 1k Units Tape and Reel 3.5k Units Tape and Reel NSC Drawing M08A MUA08A www.national.com 4 LMP7300 Connection Diagram 8-Pin MSOP/SOIC 20175606 Top View Pin Descriptions Pin Name +IN Non-Inverting Comparator Input Description The +IN has a common-mode voltage range from 1V above the negative rail to, and including, the positive rail. Internal ESD diodes, connected from the +IN pin to the rails, protect the input stage from overvoltage. If the input voltage exceeds the rails, the diodes turn on and clamp the input to a safe level. The −IN has a common-mode voltage range from 1V above the negative rail to, and including, the positive rail. Internal ESD diodes, connected from the −IN pin to the rails, protects the input stage from overvoltage. If the input voltage exceeds the rails, the diodes turn on and clamp the input to a safe level. This pin may be connected to a negative DC voltage source for applications requiring a dual supply. If connected to a negative supply, decouple this pin with 0.1 µF ceramic capacitor to ground. The internal reference output voltage is referenced to this pin. GND is the die substrate connection. The output is an open-collector. It can drive voltage loads by using a pullup resistor, or it can drive current loads by sinking a maximum output current. This pin may be taken to a maximum of +12V with respect to the ground pin, irrespective of supply voltage. This pin sets the lower trip voltage VIL. The common mode range is from 1V above the negative rail to VCC. The input signal must fall below VIL for the comparator to switch from high to low state. This pin sets the upper trip voltage VIH. The common mode range is from 1V above the negative rail to VCC. The input signal must rise above VIH for the comparator to switch from low to high state. This is the output pin of a 2.048V band gap precision reference. −IN Inverting Comparator Input GND Ground OUT Comparator Output HYSTN Negative Hysteresis Pin HYSTP Positive Hysteresis pin REF V+ Reference Voltage Output Pin Positive Supply Terminal The supply voltage range is 2.7V to 12V. Decouple this pin with 0.1 μF ceramic capacitor to ground. 5 www.national.com LMP7300 Typical Performance Characteristics Supply Current vs. Supply Voltage Output Low Voltage vs. Load Current 20175639 20175632 Output Low Voltage vs. Load Current Output Low Voltage vs. Load Current 20175633 20175634 Reference Voltage vs. Supply Voltage Reference Voltage vs. Source Current 20175635 20175636 www.national.com 6 LMP7300 Reference Voltage vs. Sink Current Reference Voltage vs. Source Current 20175637 20175638 Propagation Delay vs. Overdrive Voltage Propagation Delay vs. Overdrive Voltage 20175640 20175641 Propagation Delay vs. Overdrive Voltage 20175642 7 www.national.com LMP7300 Application Information GENERAL DESCRIPTION The LMP7300 is a unique combination of micropower and precision. The open collector comparator has low offset, high CMRR, high PSRR, programmable hysteresis and microamp supply current. The precision 2.048V reference provides a DAC or ADC with an accurate binary divisible voltage. The comparator and reference combination forms an ideal single IC solution for low power sensor or portable applications. VOLTAGE REFERENCE The reference output voltage is a band gap derived 2.048V that is trimmed to achieve typically 0.2% accuracy over the full operating temperature range of −40°C to 125°C. The trim procedure employs a curvature correction algorithm to compensate for the base emitter thermal nonlinearity inherent in band gap design topologies. The reference accuracy and the set resistor tolerance determine the magnitude and precision of the programmable hysteresis. In situations where reference noise filtering is required a 5 µF capacitor in series with a 190Ω resistor to ground are recommended. COMPARATOR Output Stage The comparator employs an open collector output stage that can switch microamp loads for micropower precision threshold detection to applications requiring activating a solenoid, a lamp, or an LED. The wired-OR type output easily interfaces to TTL, CMOS, or multiple outputs, as in a window comparator application, over a range of 0.5V to 12V. The output is capable of driving greater than 10 mA output current and yet maintaining a saturation voltage below 0.4V over temperature. The supply current increases linearly when driving heavy loads so a pullup resistor of 100 kΩ or greater is recommended for micropower applications. Fault Detection Rate The user’s choice of a pullup resistor and capacitive load determines the minimum response time and the event detection rate. By optimizing overdrive, the pullup resistor and capactive load fault update rates of 200 kHz to 250 kHz or greater can be achieved. HYSTERESIS False triggering on noise coupled into the signal path is a common problem for comparator based threshold detectors. One of the most effective solutions is to add hysteresis. Hysteresis is a circuit signal path characteristic where an amplitude delay is introduced to the normal input. Positive hysteresis forces the signal to pass the normal switch point before the output makes a low to high transition while negative hysteresis does the opposite. This is a memory effect. The comparator behaves differently based on which direction the signal is going. The LM7300 has been designed with a unique way of introducing hysteresis. The set points are completely independent of each other, the power supply, and the input or output conditions. The HYSTP pin sets positive hysteresis and the HYSTN pin sets the negative hysteresis in a simple way using two resistors. The pins can be tied together for the same hysteresis or tied to separate voltage taps for asymmetric hysteresis, or tied to the reference for no hysteresis. When the precision reference is used to drive the voltage tap resistor divider precise, stable threshold levels can be obtained. The maximum recommended hysteresis is about 130 mV. This www.national.com 8 places the HYSTP and HYSTN pin voltages at VREF – 130 mV which is approximately the center of their input common mode range at 2.7V. For the typical example, a differential input signal voltage, VIN, is applied between INP and INN, the noninverting and inverting inputs of the comparator. A DC switch or threshold voltage, VTH, is set on the negative input to keep the output off when the signal is above and on when it goes below this level. For a precision threshold tie the INN pin to VREF. With the output, off the circuit is in the minimum power state. Figure 1 through Figure 5 demonstrate the different configurations for setting the upper threshold VIH and the lower threshold VIL and their relationship to the input trip point VREF, by the following formulas. 20175607 (a) 20175608 (b) When VID = 0, INN = INP = VTH FIGURE 1. Typical Micropower Application to Set Asymmetric Positive and Negative Hysteresis of −10 mV, +3 mV LMP7300 Figure 2 shows the configuration with no hysteresis when the HYSTP and HYSTN pins are connected together to VREF. This configuration is not recommended because it has the highest level of false triggers due to the system noise. Figure 3 shows the configuration with symmetric hysteresis when the HYSTP and HYSTN pins are connected to the same voltage that is less than VREF. The two trip points set a hysteresis band around the input threshold voltage VREF, such that the positive band is equal to the negative band. This configuration controls the false triggering mentioned in Figure 2. Symmetric hysteresis values less than 5mV to 10 mV are recommended for precise level detection applications. 20175611 (a) 20175614 (a) 20175609 (b) FIGURE 2. Typical Configuration for No Hysteresis 20175612 (b) FIGURE 3. Symmetric Hysteresis ±5 mV 9 www.national.com LMP7300 Figure 4 shows the case for negative hysteresis by biasing only the HYSN pin to a voltage less than VREF. The case for setting only a positive hysteresis is demonstrated in Figure 5. 20175618 20175622 (a) (a) 20175616 20175620 (b) FIGURE 4. Typical Configuration for Negative Hysteresis = −10 mV (b) FIGURE 5. Connections for Positive Hysteresis = +10 mV www.national.com 10 LMP7300 In the general case, as demonstrated with both positive and negative hysteresis bands in Figure 6, noise within these bands will have no affect on the state of the comparator output. In Example #1 the noise is well behaved and in band. The output is clean and well behaved. In Example #2, a significant amount of out of band noise is present but due to hysteresis no false triggers occur on the rising positive or falling negative edges. The hysteresis forces the signal level to move higher or lower before the output is set to the opposite state. board phase by making R1 and R2 potentiometers. For applications near or above +100°C a minimum of 5 mV hysteresis is recommended due to peaking of the LMP7300 noise sensitivity at high temperatures. LAYOUT RECOMMENDATIONS A good PCB layout is always important to reduce output to input coupling. Positive feedback noise reduces performance. For the LMP7300 output coupling is minimized by the unique package pinout. The output is kept away from the non-inverting and inverting inputs, the reference and the hysteresis pins. EVALUATION BOARDS National Semiconductor provides the following PCB boards as an aid in evaluating the LMP7300 performance. Device LMP7300MA LMP7300MM Package 8-Pin SOIC 8-Pin MSOP Evaluation Board Ordering ID LMP7300MA-EVAL LMP7300MM-EVAL 20175628 FIGURE 6. Output Response with Input Noise Less than Hysteresis Band How Much Hysteresis Is Correct? An effective way of determining the minimum hysteresis necessary for clean switching is to decrease the amount of hysteresis until false triggering is observed, and then use a multiple of say three times that amount of hysteresis in the final circuit. This is most easily accomplished in the bread- WINDOW COMPARATOR Figure 8 shows two LMP7300s configured as a micropower window detector in a temperature level detection application. The circuit shown monitors the ambient temperature change. If the temperature rises outside the 15°C to 35°C window, either comparator 1 for high temp, or comparator 2 for low temp, will set low, indicating a fault condition has occurred. The open collector outputs are pulled up separately but can be wire-OR’d for a single fault indication. If the temperature returns inside the window it must overcome the 22 mV asymmetric hysteresis band established on either comparator. For the high side the temperature must drop below 34°C and for the low side the temperature must rise above 16°C for the outputs to reset high and remove the fault indication. The temperature is sensed by a 30 kΩ @ 25°C Omega Precision NTC Thermistor #44008 (±0.2% tol). 20175629 FIGURE 7. Temperature Controlled Window Detector to Monitor Ambient Temperature 11 www.national.com LMP7300 PRECISION HIGH TEMPERATURE SWITCH The LMP7300 brings accuracy and stability to simple sensor switch applications. Figure 9 shows the LMP7300 setup in a high temperature switch configuration. The input bridge establishes the trip point at 85°C and the reset temperature at 80°C. The comparator is set up with positive hysteresis of 14.3 mV and no negative hysteresis. When the temperature is rising it trips at 85°C. The 14.3 mV hysteresis allows the temperature to drop to 80°C before reset. The temperature sensor used is an Omega 44008 Precision NTC Thermistor. The 44008 has an accuracy of ±0.2°C. The resistance at 85°C is 3270.9Ω and at 80°C is 3840.2Ω. The trip voltage threshold is established by one half of the bridge, which is the ratio of RADJ and RSET. The input signal bias is set by the second half, which is the ratio of the thermistor resistance RTH and RSET. The resistance values are chosen for ∼50 µA bridge current to minimize the power in the thermistor. The thermistor specification states it has a 1°C/mW dissipa- tion error. The reference voltage establishes the supply voltage for the bridge to make the circuit independent of supply voltage variation. Capacitor C1 establishes a low frequency pole at FCORNER = 1/(2πC1*2(RSET//RADJ)). With the resistance values chosen C1 should be selected for Fc < 10 Hz. This will limit the thermal noise in the bridge. The accuracy of the circuit can be calculated from the nearest resistance values chosen. For 1% resistors RADJ is 3.24 kΩ, and RSET is 78.7 kΩ. The bridge gain becomes 2.488 mV/C at 85°C. In general, the higher the bridge current is allowed to be, the higher the bridge gain will be. The actual trip point found during simulation is 85.3°C and the reset point is 80.04°C. With the values chosen the worst case trip temperature uncertainty is ±1.451°C and the reset uncertainty is ±1.548°C. Accuracy could be maximized with resistors chosen to 0.1% values, 0.1% tolerance and by using the 0.1% model of the Omega 44008 thermistor. 20175647 FIGURE 8. Precision High Temperature Switch MICROPOWER PRECISION BATTERY LOW VOLTAGE DETECTOR The ability of the LMP7300 to operate at very low supply voltages, makes it an ideal choice for low battery detection application in portable equipment. The circuit in Figure 9 performs the function of low voltage threshold detection in a 3 cell 0.9V discharge voltage, battery monitor application. R1 and R2 are chosen to set the inverting input voltage equal to the non-inverting input voltage when the battery voltage is equal to the minimum operating voltage of the system. Here, the very precise reference output voltage is directly connected to the non-inverting input on the comparator and sets an accurate threshold voltage. The hysteresis is set to 0 mV negative and 20 mV positive. The output is off for voltages higher than the minimum VBATT, and turns on when the circuit detects a minimum battery voltage condition. 20175631 FIGURE 9. Battery Voltage Monitor for 3 Cell Discharge Voltage www.national.com 12 LMP7300 Physical Dimensions inches (millimeters) unless otherwise noted 8-Pin SOIC NS Package Number M08A 8-Pin MSOP NS Package Number MUA08A 13 www.national.com LMP7300 Micropower Precision Comparator and Precision Reference with Adjustable Hysteresis Notes THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION (“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright© 2007 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530-85-86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +49 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 www.national.com