LMP7704MTX

LMP7701/LMP7702/LMP7704 Precision, CMOS Input, RRIO, Wide Supply Range Amplifiers October 2006 LMP7701/LMP7702/LMP7704 Precision, CMOS Input, RRIO, Wide Supply Range Amplifiers General Description The LMP7701/LMP7702/LMP7704 are single, dual, and quad low offset voltage, rail-to-rail input and output precision amplifiers each with CMOS input stage and wide supply voltage range. The LMP7701/LMP7702/LMP7704 are part of the LMP™ precision amplifier family and are ideal for sensor interface and other instrumentation applications. The guaranteed low offset voltage of less than ± 200 µV along with the guaranteed low input bias current of less than ± 1 pA make the LMP7701 ideal for precision applications. The LMP7701/LMP7702/LMP7704 are built utilizing VIP50 technology, which allows the combination of a CMOS input stage and a 12V common mode and supply voltage range. This makes the LMP7701/LMP7702/LMP7704 great choices in many applications where conventional CMOS parts cannot operate under the desired voltage conditions. The LMP7701/LMP7702/LMP7704 have a rail-to-rail input stage that significantly reduces the CMRR glitch commonly associated with rail-to-rail input amplifiers. This is achieved by trimming both sides of the complimentary input stage, thereby reducing the difference between the NMOS and PMOS offsets. The output of the LMP7701/LMP7702/ LMP7704 swings within 40 mV of either rail to maximize the signal dynamic range in applications requiring low supply voltage. The LMP7701 is offered in the space saving 5-Pin SOT23 package, the LMP7702 is offered in the 8-Pin MSOP, and the quad LMP7704 is offered in the 14-Pin TSSOP package. These small packages are ideal solutions for area constrained PC boards and portable electronics. Features Unless otherwise noted, typical values at VS = 5V ± 200 µV (max) n Input offset voltage (LMP7701) n Input offset voltage (LMP7702/LMP7704) ± 220 µV (max) ± 200 fA n Input bias current n Input voltage noise 9 nV/ n CMRR 130 dB n Open loop gain 130 dB n Temperature range −40˚C to 125˚C n Unity gain bandwidth 2.5 MHz n Supply current (LMP7701) 715 µA n Supply current (LMP7702) 1.5 mA n Supply current (LMP7704) 2.9 mA n Supply voltage range 2.7V to 12V n Rail-to-rail input and output Applications n n n n n n High impedance sensor interface Battery powered instrumentation High gain amplifiers DAC buffer Instrumentation amplifier Active filters Typical Application 20127305 Precision Current Source LMP™ is a trademark of National Semiconductor Corporation. © 2006 National Semiconductor Corporation DS201273 www.national.com LMP7701/LMP7702/LMP7704 Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. ESD Tolerance (Note 2) Human Body Model Machine Model VIN Differential Supply Voltage (VS = V+ – V−) Voltage at Input/Output Pins Input Current Storage Temperature Range Junction Temperature (Note 3) 2000V 200V Soldering Information Infrared or Convection (20 sec) Wave Soldering Lead Temp. (10 sec) 235˚C 260˚C Operating Ratings (Note 1) Temperature Range (Note 3) Supply Voltage (VS = V – V ) Package Thermal Resistance (θJA (Note 3)) 5-Pin SOT23 8-Pin MSOP 14-Pin TSSOP 265˚C/W 235˚C/W 122˚C/W + − ± 300 mV 13.2V V++ 0.3V, V− − 0.3V 10 mA −65˚C to +150˚C +150˚C (Note 4) −40˚C to +125˚C 2.7V to 12V 3V Electrical Characteristics Symbol VOS Parameter Input Offset Voltage Unless otherwise specified, all limits are guaranteed for TA = 25˚C, V+ = 3V, V− = 0V, VCM = V+/2, and RL > 10 kΩ to V+/2. Boldface limits apply at the temperature extremes. Conditions LMP7701 LMP7702/LMP7704 TCVOS IB Input Offset Voltage Drift Input Bias Current (Note 7) (Notes 7, 8) −40˚C ≤ TA ≤ 85˚C (Notes 7, 8) −40˚C ≤ TA ≤ 125˚C IOS CMRR Input Offset Current Common Mode Rejection Ratio 0V ≤ VCM ≤ 3V LMP7701 0V ≤ VCM ≤ 3V LMP7702/LMP7704 PSRR CMVR AVOL Power Supply Rejection Ratio Input Common-Mode Voltage Range Large Signal Voltage Gain 2.7V ≤ V+ ≤ 12V, Vo = V+/2 CMRR ≥ 80 dB CMRR ≥ 77 dB RL = 2 kΩ (LMP7701) VO = 0.3V to 2.7V RL = 2 kΩ (LMP7702/LMP7704) VO = 0.3V to 2.7V RL = 10 kΩ VO = 0.2V to 2.8V 86 80 84 78 86 82 –0.2 –0.2 100 96 100 94 100 96 114 114 124 Min (Note 6) Typ (Note 5) Max (Note 6) Units ± 37 ± 56 ±1 ± 0.2 ± 0.2 40 130 130 98 ± 200 ± 500 ± 220 ± 520 ±5 ±1 ± 50 ±1 ± 400 µV µV/˚C pA fA dB dB 3.2 3.2 V dB www.national.com 2 LMP7701/LMP7702/LMP7704 3V Electrical Characteristics Symbol VO Parameter Output Swing High (Note 4) (Continued) Unless otherwise specified, all limits are guaranteed for TA = 25˚C, V+ = 3V, V− = 0V, VCM = V+/2, and RL > 10 kΩ to V+/2. Boldface limits apply at the temperature extremes. Conditions RL = 2 kΩ to V+/2 LMP7701 RL = 2 kΩ to V+/2 LMP7702/LMP7704 RL = 10 kΩ to V+/2 LMP7701 RL = 10 kΩ to V+/2 LMP7702/LMP7704 Output Swing Low RL = 2 kΩ to V+/2 LMP7701 RL = 2 kΩ to V+/2 LMP7702/LMP7704 RL = 10 kΩ to V+/2 LMP7701 RL = 10 kΩ to V+/2 LMP7702/LMP7704 IO Output Short Circuit Current (Notes 3, 9) Sourcing VO = V+/2 VIN = 100 mV Sinking VO = V+/2 VIN = −100 mV (LMP7701) Sinking VO = V /2 VIN = −100 mV (LMP7702/LMP7704) IS Supply Current LMP7701 LMP7702 LMP7704 SR GBW THD+N en in Slew Rate (Note 10) Gain Bandwidth Product Total Harmonic Distortion + Noise Input-Referred Voltage Noise Input-Referred Current Noise f = 1 kHz, AV = 1, R.L = 10 kΩ f = 1 kHz f = 100 kHz (Note 4) AV = +1, VO = 2 VPP 10% to 90% + Min (Note 6) Typ (Note 5) 40 40 30 35 40 45 20 20 Max (Note 6) 80 120 80 150 40 60 50 100 60 80 100 170 40 50 50 90 Units mV from V+ mV 25 15 25 20 25 15 42 42 mA 42 0.670 1.4 2.9 0.9 2.5 0.02 9 1 1.0 1.2 1.8 2.1 3.5 4.5 V/µs MHz % nV/ fA/ mA 5V Electrical Characteristics Symbol VOS Parameter Input Offset Voltage Unless otherwise specified, all limits are guaranteed for TA = 25˚C, V+ = 5V, V− = 0V, VCM = V+/2, and RL > 10 kΩ to V+/2. Boldface limits apply at the temperature extremes. Conditions LMP7701 LMP7702/LMP7704 TCVOS Input Offset Voltage Drift (Note 7) Min (Note 6) Typ (Note 5) Max (Note 6) Units ± 37 ± 32 ±1 ± 200 ± 500 ± 220 ± 520 ±5 µV µV/˚C 3 www.national.com LMP7701/LMP7702/LMP7704 5V Electrical Characteristics Symbol IB Parameter Input Bias Current (Note 4) (Continued) Unless otherwise specified, all limits are guaranteed for TA = 25˚C, V+ = 5V, V− = 0V, VCM = V+/2, and RL > 10 kΩ to V+/2. Boldface limits apply at the temperature extremes. Conditions (Notes 7, 8) −40˚C ≤ TA ≤ 85˚C (Notes 7, 8) −40˚C ≤ TA ≤ 125˚C IOS CMRR Input Offset Current Common Mode Rejection Ratio 0V ≤ VCM ≤ 5V LMP7701 0V ≤ VCM ≤ 5V LMP7702/LMP7704 PSRR CMVR AVOL Power Supply Rejection Ratio Input Common-Mode Voltage Range Large Signal Voltage Gain 2.7V ≤ V+ ≤ 12V, VO = V+/2 CMRR ≥ 80 dB CMRR ≥ 78 dB RL = 2 kΩ (LMP7701) VO = 0.3V to 4.7V RL = 2 kΩ (LMP7702/LMP7704) VO = 0.3V to 4.7V RL = 10 kΩ VO = 0.2V to 4.8V VO Output Swing High RL = 2 kΩ to V+/2 LMP7701 RL = 2 kΩ to V+/2 LMP7702/LMP7704 RL = 10 kΩ to V+/2 LMP7701 RL = 10 kΩ to V+/2 LMP7702/LMP7704 Output Swing Low RL = 2 kΩ to V+/2 LMP7701 RL = 2 kΩ to V+/2 LMP7702/LMP7704 RL = 10 kΩ to V+/2 LMP7701 RL = 10 kΩ to V+/2 LMP7702/LMP7704 IO Output Short Circuit Current (Notes 3, 9) Sourcing VO = V+/2 VIN = 100 mV (LMP7701) Sourcing VO = V+/2 VIN = 100 mV (LMP7702/LMP7704) Sinking VO = V+/2 VIN = −100 mV (LMP7701) Sinking VO = V+/2 VIN = −100 mV (LMP7702/LMP7704) 40 28 38 25 40 28 40 23 88 83 86 81 86 82 –0.2 –0.2 100 96 100 94 100 96 119 119 130 60 60 40 40 50 50 30 30 66 66 110 130 120 200 50 70 60 120 80 90 120 190 40 50 50 100 mV from V+ Min (Note 6) Typ (Note 5) Max (Note 6) Units ± 0.2 ± 0.2 40 130 130 100 ±1 ± 50 ±1 ± 400 pA fA dB dB 5.2 5.2 V dB mV 76 76 mA www.national.com 4 LMP7701/LMP7702/LMP7704 5V Electrical Characteristics Symbol IS Parameter Supply Current (Note 4) (Continued) Unless otherwise specified, all limits are guaranteed for TA = 25˚C, V+ = 5V, V− = 0V, VCM = V+/2, and RL > 10 kΩ to V+/2. Boldface limits apply at the temperature extremes. Conditions LMP7701 LMP7702 LMP7704 SR GBW THD+N en in Slew Rate (Note 10) Gain Bandwidth Product Total Harmonic Distortion + Noise Input-Referred Voltage Noise Input-Referred Current Noise f = 1 kHz, AV = 1, RL = 10 kΩ f = 1 kHz f = 100 kHz AV = +1, VO = 4 VPP 10% to 90% Min (Note 6) Typ (Note 5) 0.715 1.5 2.9 1.0 2.5 0.02 9 1 nV/ fA/ Max (Note 6) 1.0 1.2 1.9 2.2 3.7 4.6 V/µs MHz % mA Units ± 5V Electrical Characteristics (Note 4) Unless otherwise specified, all limits are guaranteed for TA = 25˚C, V+ = 5V, V− = −5V, VCM = 0V, and RL > 10 kΩ to 0V. Boldface limits apply at the temperature extremes. Symbol VOS Parameter Input Offset Voltage LMP7701 LMP7702/LMP7704 TCVOS IB Input Offset Voltage Drift Input Bias Current (Note 7) (Notes 7, 8) −40˚C ≤ TA ≤ 85˚C (Notes 7, 8) −40˚C ≤ TA ≤ 125˚C IOS CMRR Input Offset Current Common Mode Rejection Ratio −5V ≤ VCM ≤ 5V LMP7701 −5V ≤ VCM ≤ 5V LMP7702/LMP7704 PSRR CMVR AVOL Power Supply Rejection Ratio Input Common-Mode Voltage Range Large Signal Voltage Gain 2.7V ≤ V+ ≤ 12V, VO = 0V CMRR ≥ 80 dB CMRR ≥ 78 dB RL = 2 kΩ (LMP7701) VO = −4.7V to 4.7V RL = 2 kΩ (LMP7702/LMP7704) VO = −4.7V to 4.7V RL = 10 kΩ (LMP7701) VO = −4.8V to 4.8V RL = 10 kΩ (LMP7702/LMP7704) VO = −4.8V to 4.8V 92 88 90 86 86 82 −5.2 −5.2 100 98 100 94 100 98 100 97 121 121 134 134 dB Conditions Min (Note 6) Typ (Note 5) Max (Note 6) Units ± 37 ± 37 ±1 ± 0.2 ± 0.2 40 138 138 98 ± 200 ± 500 ± 220 ± 520 ±5 1 µV µV/˚C ± 50 1 ± 400 pA fA dB dB 5.2 5.2 V 5 www.national.com LMP7701/LMP7702/LMP7704 ± 5V Electrical Characteristics (Note 4) Symbol VO Parameter Output Swing High (Continued) Unless otherwise specified, all limits are guaranteed for TA = 25˚C, V+ = 5V, V− = −5V, VCM = 0V, and RL > 10 kΩ to 0V. Boldface limits apply at the temperature extremes. Conditions RL = 2 kΩ to 0V LMP7701 RL = 2 kΩ to 0V LMP7702/LMP7704 RL = 10 kΩ to 0V LMP7701 RL = 10 kΩ to 0V LMP7702/LMP7704 Output Swing Low RL = 2 kΩ to 0V LMP7701 RL = 2 kΩ to 0V LMP7702/LMP7704 RL = 10 kΩ to 0V LMP7701 RL = 10 kΩ to 0V LMP7702/LMP7704 IO Output Short Circuit Current (Notes 3, 9) Sourcing VO = 0V VIN = 100 mV (LMP7701) Sourcing VO = 0V VIN = 100 mV (LMP7702/LMP7704) Sinking VO = 0V VIN = −100 mV IS Supply Current LMP7701 LMP7702 LMP7704 SR GBW THD+N en in Slew Rate (Note 10) Gain Bandwidth Product Total Harmonic Distortion + Noise Input-Referred Voltage Noise Input-Referred Current Noise f = 1 kHz, AV = 1, RL = 10 kΩ f = 1 kHz f = 100 kHz AV = +1, VO = 9 VPP 10% to 90% 50 35 48 33 50 35 Min (Note 6) Typ (Note 5) 90 90 40 40 90 90 40 40 86 86 mA 84 0.790 1.7 3.2 1.1 2.5 0.02 9 1 nV/ fA/ 1.1 1.3 2.1 2.5 4.2 5.0 V/µs MHz % mA Max (Note 6) 150 170 180 290 80 100 80 150 130 150 180 290 50 60 60 110 mV from V– mV from V+ Units Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics Tables. Note 2: Human Body Model is 1.5 kΩ in series with 100 pF. Machine Model is 0Ω in series with 200 pF. Note 3: The maximum power dissipation is a function of TJ(MAX), θJA, and TA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(MAX) - TA)/ θJA . All numbers apply for packages soldered directly onto a PC board. Note 4: Electrical table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very limited self-heating of the device. Note 5: Typical values represent the parametric norm at the time of characterization. Note 6: Limits are 100% production tested at 25˚C. Limits over the operating temperature range are guaranteed through correlations using the Statistical Quality Control (SQC) method. Note 7: Guaranteed by design. Note 8: Positive current corresponds to current flowing into the device. Note 9: The short circuit test is a momentary test. Note 10: The number specified is the slower of positive and negative slew rates. www.national.com 6 LMP7701/LMP7702/LMP7704 Connection Diagrams 5-Pin SOT23 8-Pin MSOP 14-Pin TSSOP 20127302 20127303 Top View Top View 20127304 Top View Ordering Information Package 5-Pin SOT23 8-Pin MSOP 14-Pin TSSOP Part Number LMP7701MF LMP7701MFX LMP7702MM LMP7702MMX LMP7704MT LMP7704MTX Package Marking AC2A AA3A LMP7704MT Transport Media 1k Units Tape and Reel 3k Units Tape and Reel 1k Units Tape and Reel 3.5k Units Tape and Reel 94 Units/Rail 2.5k Units Tape and Reel NSC Drawing MF05A MUA08A MTC14 7 www.national.com LMP7701/LMP7702/LMP7704 Typical Performance Characteristics Offset Voltage Distribution Unless otherwise noted: TA = 25˚C, VCM = VS/2, RL > 10 kΩ. TCVOS Distribution 20127336 20127341 Offset Voltage Distribution TCVOS Distribution 20127337 20127342 Offset Voltage Distribution TCVOS Distribution 20127338 20127343 www.national.com 8 LMP7701/LMP7702/LMP7704 Typical Performance Characteristics Unless otherwise noted: TA = 25˚C, VCM = VS/2, RL > 10 kΩ. (Continued) Offset Voltage vs. Temperature CMRR vs Frequency 20127306 20127350 Offset Voltage vs. Supply Voltage Offset Voltage vs. VCM 20127310 20127307 Offset Voltage vs. VCM Offset Voltage vs. VCM 20127308 20127309 9 www.national.com LMP7701/LMP7702/LMP7704 Typical Performance Characteristics Unless otherwise noted: TA = 25˚C, VCM = VS/2, RL > 10 kΩ. (Continued) Input Bias Current vs. VCM Input Bias Current vs. VCM 20127346 20127330 Input Bias Current vs. VCM Input Bias Current vs. VCM 20127347 20127331 Input Bias Current vs. VCM Input Bias Current vs. VCM 20127348 20127349 www.national.com 10 LMP7701/LMP7702/LMP7704 Typical Performance Characteristics Unless otherwise noted: TA = 25˚C, VCM = VS/2, RL > 10 kΩ. (Continued) PSRR vs. Frequency Supply Current vs. Supply Voltage (Per Channel) 20127345 20127311 Sinking Current vs. Supply Voltage Sourcing Current vs. Supply Voltage 20127313 20127312 Output Voltage vs. Output Current Slew Rate vs. Supply Voltage 20127316 20127317 11 www.national.com LMP7701/LMP7702/LMP7704 Typical Performance Characteristics Unless otherwise noted: TA = 25˚C, VCM = VS/2, RL > 10 kΩ. (Continued) Open Loop Frequency Response Open Loop Frequency Response 20127315 20127314 Large Signal Step Response Small Signal Step Response 20127318 20127320 Large Signal Step Response Small Signal Step Response 20127319 20127326 www.national.com 12 LMP7701/LMP7702/LMP7704 Typical Performance Characteristics Unless otherwise noted: TA = 25˚C, VCM = VS/2, RL > 10 kΩ. (Continued) Input Voltage Noise vs. Frequency Open Loop Gain vs. Output Voltage Swing 20127327 20127352 Output Swing High vs. Supply Voltage Output Swing Low vs. Supply Voltage 20127333 20127335 Output Swing High vs. Supply Voltage Output Swing Low vs. Supply Voltage 20127332 20127334 13 www.national.com LMP7701/LMP7702/LMP7704 Typical Performance Characteristics Unless otherwise noted: TA = 25˚C, VCM = VS/2, RL > 10 kΩ. (Continued) THD+N vs. Frequency THD+N vs. Output Voltage 20127328 20127329 Crosstalk Rejection Ratio vs. Frequency (LMP7702/LMP7704) 20127353 www.national.com 14 LMP7701/LMP7702/LMP7704 Application Information LMP7701/LMP7702/LMP7704 The LMP7701/LMP7702/LMP7704 are single, dual, and quad low offset voltage, rail-to-rail input and output precision amplifiers each with CMOS input stage and wide supply voltage range of 2.7V to 12V. The LMP7701/LMP7702/ LMP7704 have a very low input bias current of only ± 200 fA at room temperature. The wide supply voltage range of 2.7V to 12V over the extensive temperature range of −40˚C to 125˚C makes the LMP7701/LMP7702/LMP7704 excellent choices for low voltage precision applications with extensive temperature requirements. The LMP7701/LMP7702/LMP7704 have only ± 37 µV of typical input referred offset voltage and this offset is guaranteed to be less than ± 500 µV for the single and ± 520 µV for the dual and quad, over temperature. This minimal offset voltage allows more accurate signal detection and amplification in precision applications. The low input bias current of only ± 200 fA along with the low give the LMP7701/ input referred voltage noise of 9 nV/ LMP7702/LMP7704 superiority for use in sensor applications. Lower levels of noise introduced by the amplifier mean better signal fidelity and a higher signal-to-noise ratio. National Semiconductor is heavily committed to precision amplifiers and the market segment they serve. Technical support and extensive characterization data is available for sensitive applications or applications with a constrained error budget. The LMP7701 is offered in the space saving 5-Pin SOT23 package, the LMP7702 comes in the 8-pin MSOP, and the LMP7704 is offered in the 14-Pin TSSOP package. These small packages are ideal solutions for area constrained PC boards and portable electronics. CAPACITIVE LOAD The LMP7701/LMP7702/LMP7704 can each be connected as a non-inverting unity gain follower. This configuration is the most sensitive to capacitive loading. The combination of a capacitive load placed on the output of an amplifier along with the amplifier’s output impedance creates a phase lag which in turn reduces the phase margin of the amplifier. If the phase margin is significantly reduced, the response will be either underdamped or it will oscillate. In order to drive heavier capacitive loads, an isolation resistor, RISO, in Figure 1 should be used. By using this isolation resistor, the capacitive load is isolated from the amplifier’s output, and hence, the pole caused by CL is no longer in the feedback loop. The larger the value of RISO, the more stable the output voltage will be. If values of RISO are sufficiently large, the feedback loop will be stable, independent of the value of CL. However, larger values of RISO result in reduced output swing and reduced output current drive. 20127321 FIGURE 1. Isolating Capacitive Load INPUT CAPACITANCE CMOS input stages inherently have low input bias current and higher input referred voltage noise. The LMP7701/ LMP7702/LMP7704 enhance this performance by having the low input bias current of only ± 200 fA, as well as, a very . In order to low input referred voltage noise of 9 nV/ achieve this a larger input stage has been used. This larger input stage increases the input capacitance of the LMP7701/ LMP7702/ LMP7704. The typical value of this input capacitance, CIN, for the LMP7701/LMP7702/LMP7704 is 25 pF. The input capacitance will interact with other impedances such as gain and feedback resistors, which are seen on the inputs of the amplifier, to form a pole. This pole will have little or no effect on the output of the amplifier at low frequencies and DC conditions, but will play a bigger role as the frequency increases. At higher frequencies, the presence of this pole will decrease phase margin and will also cause gain peaking. In order to compensate for the input capacitance, care must be taken in choosing the feedback resistors. In addition to being selective in picking values for the feedback resistor, a capacitor can be added to the feedback path to increase stability. The DC gain of the circuit shown in Figure 2 is simply –R2/R1. 20127344 FIGURE 2. Compensating for Input Capacitance For the time being, ignore CF. The AC gain of the circuit in Figure 2 can be calculated as follows: 15 www.national.com LMP7701/LMP7702/LMP7704 Application Information (Continued) nates the gain peaking that can be caused by having a larger feedback resistor. Figure 4 shows how CF reduces gain peaking. This equation is rearranged to find the location of the two poles: (1) As shown in Equation (1), as values of R1 and R2 are increased, the magnitude of the poles is reduced, which in turn decreases the bandwidth of the amplifier. Whenever possible, it is best to choose smaller feedback resistors. Figure 3 shows the effect of feedback resistor on the LMP7701/LMP7702/LMP7704 bandwidth. 20127355 FIGURE 4. Closed Loop Gain vs. Frequency with Compensation DIODES BETWEEN THE INPUTS The LMP7701/LMP7702/LMP7704 have a set of anti-parallel diodes between the input pins, as shown in Figure 5. These diodes are present to protect the input stage of the amplifier. At the same time, they limit the amount of differential input voltage that is allowed on the input pins. A differential signal larger than one diode voltage drop might damage the diodes. The differential signal between the inputs needs to be limited to ± 300 mV or the input current needs to be limited to ± 10 mA. 20127354 FIGURE 3. Closed Loop Gain vs. Frequency Equation (1) has two poles. In most cases, it is the presence of pairs of poles that causes gain peaking. In order to eliminate this effect, the poles should be placed in Butterworth position, since poles in Butterworth position do not cause gain peaking. To achieve a Butterworth pair, the quantity under the square root in Equation (1) should be set to equal −1. Using this fact and the relation between R1 and R2, R2 = −AV R1, the optimum value for R1 can be found. This is shown in Equation (2). If R1 is chosen to be larger than this optimum value, gain peaking will occur. 20127325 FIGURE 5. Input of LMP7701 (2) In Figure 2, CF is added to compensate for input capacitance and to increase stability. Additionally, CF reduces or elimi- www.national.com 16 LMP7701/LMP7702/LMP7704 Application Information PRECISION CURRENT SOURCE (Continued) The LMP7701/LMP7702/LMP7704 can each be used as a precision current source in many different applications. Figure 6 shows a typical precision current source. This circuit implements a precision voltage controlled current source. Amplifier A1 is a differential amplifier that uses the voltage drop across RS as the feedback signal. Amplifier A2 is a buffer that eliminates the error current from the load side of the RS resistor that would flow in the feedback resistor if it were connected to the load side of the RS resistor. In general, the circuit is stable as long as the closed loop bandwidth of amplifier A2 is greater then the closed loop bandwidth of amplifier A1. Note that if A1 and A2 are the same type of amplifiers, then the feedback around A1 will reduce its bandwidth compared to A2. circuit is divided by the square root of the number of amplifiers used in this parallel combination. This is because each individual amplifier acts as an independent noise source, and the average noise of independent sources is the quadrature sum of the independent sources divided by the number of sources. For N identical amplifiers, this means: Figure 7 shows a schematic of this input voltage noise reduction circuit. Typical resistor values are: RG = 10Ω, RF = 1 kΩ, and RO = 1 kΩ. 20127305 FIGURE 6. Precision Current Source The equation for output current can be derived as follows: Solving for the current I results in the following equation: LOW INPUT VOLTAGE NOISE The LMP7701/LMP7702/LMP7704 have very low input volt. This input voltage noise can be age noise of 9 nV/ further reduced by placing N amplifiers in parallel as shown in Figure 7. The total voltage noise on the output of this 20127356 FIGURE 7. Noise Reduction circuit 17 www.national.com LMP7701/LMP7702/LMP7704 Application Information TOTAL NOISE CONTRIBUTION (Continued) The LMP7701/LMP7702/LMP7704 have very low input bias current, very low input current noise, and very low input voltage noise. As a result, these amplifiers are ideal choices for circuits with high impedance sensor applications. Figure 8 shows the typical input noise of the LMP7701/ LMP7702/LMP7704 as a function of source resistance where: en denotes the input referred voltage noise ei is the voltage drop across source resistance due to input referred current noise or ei = RS * in et shows the thermal noise of the source resistance eni shows the total noise on the input. Where: HIGH IMPEDANCE SENSOR INTERFACE Many sensors have high source impedances that may range up to 10 MΩ. The output signal of sensors often needs to be amplified or otherwise conditioned by means of an amplifier. The input bias current of this amplifier can load the sensor’s output and cause a voltage drop across the source resistance as shown in Figure 9, where VIN+ = VS – IBIAS*RS The last term, IBIAS*RS, shows the voltage drop across RS. To prevent errors introduced to the system due to this voltage, an op amp with very low input bias current must be used with high impedance sensors. This is to keep the error contribution by IBIAS*RS less than the input voltage noise of the amplifier, so that it will not become the dominant noise factor. The input current noise of the LMP7701/LMP7702/LMP7704 is so low that it will not become the dominant factor in the total noise unless source resistance exceeds 300 MΩ, which is an unrealistically high value. As is evident in Figure 8, at lower RS values, total noise is dominated by the amplifier’s input voltage noise. Once RS is larger than a few kilo-Ohms, then the dominant noise factor becomes the thermal noise of RS. As mentioned before, the current noise will not be the dominant noise factor for any practical application. 20127359 FIGURE 9. Noise Due to IBIAS pH electrodes are very high impedance sensors. As their name indicates, they are used to measure the pH of a solution. They usually do this by generating an output voltage which is proportional to the pH of the solution. pH electrodes are calibrated so that they have zero output for a neutral solution, pH = 7, and positive and negative voltages for acidic or alkaline solutions. This means that the output of a pH electrode is bipolar and has to be level shifted to be used in a single supply system. The rate of change of this voltage is usually shown in mV/pH and is different for different pH sensors. Temperature is also an important factor in a pH electrode reading. The output voltage of the senor will change with temperature. Figure 10 shows a typical output voltage spectrum of a pH electrode. Note that the exact values of output voltage will be different for different sensors. In this example, the pH electrode has an output voltage of 59.15 mV/pH at 25˚C. 20127358 FIGURE 8. Total Input Noise 20127360 FIGURE 10. Output Voltage of a pH Electrode The temperature dependence of a typical pH electrode is shown in Figure 11. As is evident, the output voltage changes with changes in temperature. www.national.com 18 LMP7701/LMP7702/LMP7704 Application Information (Continued) is used to measure the temperature of the solution and feeds this reading to the Analog to Digital Converter, ADC. This information is used by the ADC to calculate the temperature effects on the pH readings. The LM35 needs to have a resistor, RT in Figure 12, to –V+ in order to be able to read temperatures below 0˚C. RT is not needed if temperatures are not expected to go below zero. The output of pH electrodes are usually large enough that they don’t require much amplification; however, due to the very high impedance, the output of a pH electrode needs to be buffered before it can go to an ADC. Since most ADCs are operated on single supply, the output of the pH electrode also needs to be level shifted. Amplifier A1 buffers the output of the pH electrode with a moderate gain of +2, while A2 provides the level shifting. VOUT at the output of A2 is given by: VOUT = −2VpH + 1.024V. LM4140A is a precision, low noise, voltage reference used to provide the level shift needed. The ADC used in this application is the ADC12032 which is a 12-bit, 2 channel converter with multiplexers on the inputs and a serial output. The 12-bit ADC enables users to measure pH with an accuracy of 0.003 of a pH unit. Adequate power supply bypassing and grounding is extremely important for ADCs. Recommended bypass capacitors are shown in Figure 12. It is common to share power supplies between different components in a circuit. To minimize the effects of power supply ripples caused by other components, the op amps need to have bypass capacitors on the supply pins. Using the same value capacitors as those used with the ADC are ideal. The combination of these three values of capacitors ensures that AC noise present on the power supply line is grounded and does not interfere with the amplifiers’ signal. 20127361 FIGURE 11. Temperature Dependence of a pH Electrode The schematic shown in Figure 12 is a typical circuit which can be used for pH measurement. The LM35 is a precision integrated circuit temperature sensor. This sensor is differentiated from similar products because it has an output voltage linearly proportional to Celcius measurement, without the need to convert the temperature to Kelvin. The LM35 20127362 FIGURE 12. pH Measurement Circuit 19 www.national.com LMP7701/LMP7702/LMP7704 Physical Dimensions inches (millimeters) unless otherwise noted 5-Pin SOT23 NS Package Number MF05A 8-Pin MSOP NS Package Number MUA08A www.national.com 20 LMP7701/LMP7702/LMP7704 Precision, CMOS Input, RRIO, Wide Supply Range Amplifiers Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 14-Pin TSSOP NS Package Number MTC14 THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION (″NATIONAL″) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are trademarks or registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright © 2006 National Semiconductor Corporation. For the most current product information visit us at www.national.com. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com LMP7701/LMP7702/LMP7704 Precision, CMOS Input, RRIO, Wide Supply Range Amplifiers www.national.com Tel: 81-3-5639-7560