LMV301MG

LMV301 Low Input Bias Current, 1.8V Op Amp w/ Rail-to-Rail Output March 2001 LMV301 Low Input Bias Current, 1.8V Op Amp w/ Rail-to-Rail Output General Description The LMV301 CMOS operational amplifier is ideal for single supply, low voltage operation with a guaranteed operating voltage range from 1.8V to 5V. The low input bias current of less than 0.182pA typical, eliminates input voltage errors that may originate from small input signals. This makes the LMV301 ideal for electrometer applications requiring low input leakage such as sensitive photodetection transimpedance amplifiers and sensor amplifiers. The LMV301 also features a rail-to-rail output voltage swing in addition to a input common-mode range that includes ground. The LMV301 will drive a 600Ω resistive load and up to 1000pF capacitive load in unity gain follower applications. The low supply voltage also makes the LMV301 well suited for portable two-cell battery systems and single cell Li-Ion systems. The LMV301 exhibits excellent speed-power ratio, achieving 1MHz at unity gain with low supply current. The high DC gain of 100dB makes it ideal for other low frequency applications. The LMV301 is offered in a space saving SC-70 package, which is only 2.0X2.1X1.0mm. It is also similar to the LMV321 except the LMV301 has a CMOS input. Key Specifications (Typical values unless otherwise specified) n Input bias current 0.182pA n Gain bandwidth product 1MHz n Supply voltage @ 1.8V 1.8V to 5V n Supply current 150µA n Input referred voltage noise @ 1kHz 40nV/ n DC Gain (600Ω load) 100dB n Output voltage range @ 1.8V 0.024 to 1.77V n Input common-mode voltage range −0.3V to V+ - 1.2V Applications n n n n n Thermocouple amplifiers Photo current amplifiers Transducer amplifiers Sample and hold circuits Low frequency active filters Connection Diagram SC70-5 Applications Circuit Low Leakage Sample and Hold 20019307 20019301 Top View Ordering Information Package 5-Pin SC70-5 Part Number LMV301MG LMV301MGX Package Marking A48 Transport Media 1k Units Tape and Reel 3k Units Tape and Reel NSC Drawing MAA05A © 2001 National Semiconductor Corporation DS200193 www.national.com LMV301 Absolute Maximum Ratings (Note 1) Mounting Temperature Infrared or Convection (20 sec) Junction Temperature (Note 3) 235˚C 150˚C If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/Distributors for availability and specifications. ESD Tolerance (Note 7) Machine Model Human Body Model Differential Input Voltage Supply Voltage (V - V ) Output Short Circuit to V+ (Note 2) Output Short Circuit to V− (Note 2) Storage Tempeature Range −65˚C to 150˚C + − 200V 2000V Operating Ratings(Note 1) Supply Voltage Temperature Range Thermal Resistance (θJA) Ultra Tiny SC70-5 Package 5-pin Surface Mount 478˚C/W 1.8V to 5.0V −40˚C ≤ TJ ≤ +85˚C ± Supply Voltage 5.5V 1.8V DC Electrical Characteristics Symbol VOS IB IS CMRR PSRR VCM AV Parameter Input Offset Voltage Input Bias Current Supply Current Common Mode Rejection Ratio Power Supply Rejection Ratio Unless otherwise specified, all limits guaranteed for TJ = 25˚C. V+ = 1.8V, V− = 0V, VCM = V+/2, VO = V+/2, and RL > 1MΩ. Boldface limits apply at the temperature extremes. Condition VCM = 0.4V, V+ = 1.3V, = V− = −0.5V Min (Note 5) Typ (Note 4) 0.9 0.182 VCM = 0.4V, V+ = 1.3V, = V− = −0.5V 0.3V ≤ VCM ≤ 0.9V 1.8V ≤ V+ ≤ 5V, 0.9 ≤ VCM ≤ 2.5V 62 60 67 62 −0.3 0 80 75 80 75 80 75 80 75 1.65 1.63 1.75 1.74 119 111 94 96 1.72 0.074 1.77 0.024 4 3.3 7 8.4 9.8 0.035 0.040 0.100 dB dB 150 108 110 0.6 Max (Note 5) 8 9 35 50 250 275 Units mV pA µA dB dB V Input Common-Mode Voltage For CMRR ≥ 50dB Range Large Signal Voltage Gain Sourcing RL = 600Ω to 0V, V+ = 1.2V, V− = −0.6V, VO = −0.2V to 0.8V, VCM = 0V RL = 2kΩ to 0V, V+ = 1.2V, V− = −0.6V, VO = −0.2V to 0.8V, VCM = 0V Sinking RL = 600Ω to 0V, V+ = 1.2V, V− = −0.6V, VO = −0.2V to 0.8V, VCM = 0V RL = 2kΩ to 0V, V+ = 1.2V, V− = −0.6V, VO = −0.2V to 0.8V, VCM = 0V VO Output Swing RL = 600Ω to 0.9V VIN = ± 100mV RL = 2kΩ to 0.9V VIN = ± 100mV VOH VOL VOH VOL V V V V mA mA IO Output Short Circuit Current Sourcing, VO = 0V, VIN = 100mV Sinking, VO = 1.8V, VIN = −100mV www.national.com 2 LMV301 1.8V AC Electrical Characteristics = 1.8V, V = 0V, VCM Symbol SR GBW φm Gm en THD − + + Unless otherwise specified, all limits guaranteed for TJ = 25˚C. V+ = V /2, VO = V /2, and RL > 1MΩ. Boldface limits apply at the temperature extremes. Parameter Condition (Note 6) Typ (Note 4) 0.57 1 60 10 f = 1kHz, VCM = 0.5V f = 100kHz f = 1kHz, AV = +1 RL = 600kΩ, VIN = 1VPP 40 30 0.089 Units V/µs MHz Deg dB nV/ % Slew Rate Gain Bandwidth Product Phase Margin Gain Margin Input-Referred Voltage Noise Total Harmonic Distortion 2.7V DC Electrical Characteristics Symbol VOS IB IS CMRR PSRR VCM AV Parameter Input Offset Voltage Input Bias Current Supply Current Common Mode Rejection Ratio Power Supply Rejection Ratio Unless otherwise specified, all limits guaranteed for TJ = 25˚C. V+ = 2.7V, V− = 0V, VCM = V+/2, VO = V+/2, and RL > 1MΩ. Boldface limits apply at the temperature extremes. Condition VCM = 0.35V, V+ = 1.7V, V− = −1V Min (Note 5) Typ (Note 4) 0.9 0.182 VCM = 0.35V, V+ = 1.7V, V− = −1V −0.15V ≤ VCM ≤ 1.35V 1.8V ≤ V+ ≤ 5V 62 60 67 62 −0.3 0 80 75 83 77 80 75 80 75 2.550 2.530 2.650 2.640 20 15 19 12 100 114 98 99 2.62 0.078 2.675 0.024 32 24 0.045 0.100 dB dB 153 115 110 1.5 Max (Note 5) 8 9 35 50 250 275 Units mV pA µA dB dB V Input Common-Mode Voltage For CMRR ≥ 50dB Range Large Signal Voltage Gain Sourcing RL = 600Ω to 0V, V+ = 1.35V, V− = −1.35V, VO = −1V to 1V, VCM = 0V RL = 2kΩ to 0V, V+ = 1.35V, V− = −1.35V, VO = −1V to 1V, VCM = 0V Sinking RL = 600Ω to 0V, V+ = 1.35V, V− = −1.35V, VO = −1V to 1V, VCM = 0V RL = 2kΩ to 0V, V+ = 1.35V, V− = −1.35V, VO = −1V to 1V, VCM = 0V VO Output Swing RL = 600Ω to 1.35V VIN = ± 100mV RL = 2kΩ to 1.35V VIN = ± 100mV VOH VOL VOH VOL V V V V mA mA IO Output Short Circuit Current Sourcing, VO = 0V, VIN = 100mV Sinking, VO = 2.7V, VIN = −100mV 3 www.national.com LMV301 2.7V AC Electrical Characteristics = 2.7V, V = 0V, VCM Symbol SR GBW φm Gm en THD − Unless otherwise specified, all limits guaranteed for TJ = 25˚C. V+ = 1.0V, VO = 1.35V and RL > 1MΩ. Boldface limits apply at the temperature extremes. Parameter Condition (Note 6) Typ (Note 4) 0.60 1 65 10 f = 1kHz, VCM = 0.5V f = 100kHz f = 1kHz, AV = +1 RL = 600kΩ, VIN = 1VPP 40 30 0.077 Units V/µs MHz Deg dB nV/ % Slew Rate Gain Bandwidth Product Phase Margin Gain Margin Input-Referred Voltage Noise Total Harmonic Distortion 5V DC Electrical Characteristics Symbol VOS IB IS CMRR PSRR VCM AV Parameter Input Offset Voltage Input Bias Current Supply Current Common Mode Rejection Ratio Power Supply Rejection Ratio Input Common-Mode Voltage Range Large Signal Voltage Gain Sourcing Unless otherwise specified, all limits guaranteed for TJ = 25˚C. V+ = 5V, V− = 0V, VCM = V+/2, VO = V+/2, and RL > 1MΩ. Boldface limits apply at the temperature extremes. Condition VCM = 0.5V, V+ = 3V, V− = −2V Min (Note 5) Typ (Note 4) 0.9 0.182 VCM = 0.5V, V+ = 3V, V− = −2V −1.3V ≤ VCM ≤ 2.5V 1.8V ≤ V+ ≤ 5V For CMRR ≥ 50dB RL = 600Ω to 0V, V+ = 2.5V, V− = −2.5V, VO = −2V to 2V, VCM = 0V RL = 2kΩ to 0V, V+ = 2.5V, V− = −2.5V, VO = −2V to 2V, VCM = 0V Sinking RL = 600Ω to 0V, V+ = 2.5V, V− = −2.5V, VO = −2V to 2V, VCM = 0V RL = 2kΩ to 0V, V+ = 2.5V, V− = −2.5V, VO = −2V to 2V, VCM = 0V 62 61 67 62 −0.3 0 86 82 89 85 80 75 80 75 4.850 4.840 117 116 105 107 4.893 0.1 4.935 4.966 0.034 85 68 60 45 108 69 0.065 0.075 0.150 1.160 dB dB 163 111 110 3.8 Max (Note 5) 8 9 35 50 260 285 Units mV pA µA dB dB V VO Output Swing RL = 600Ω to 2.5V VIN = ± 100mV VOH VOL V V V V mA mA RL = 2kΩ to 2.5V VIN = ± 100mV IO Output Short Circuit Current Sourcing, VO = 0V, VIN = 100mV Sinking, VO = 5V, VIN = −100mV VOH VOL www.national.com 4 LMV301 5V AC Electrical Characteristics 5V, V = 0V, VCM Symbol SR GBW φm Gm en THD − + Unless otherwise specified, all limits guaranteed for TJ = 25˚C. V+ = = V /2, VO = 2.5V and RL > 1MΩ. Boldface limits apply at the temperature extremes. Parameter Slew Rate Gain Bandwidth Product Phase Margin Gain Margin Input-Referred Voltage Noise Total Harmonic Distortion f = 1kHz, VCM = 1V f = 100kHz f = 1kHz, AV = +1 RL = 600Ω, VO = 1VPP (Note 6) Condition Typ (Note 4) 0.66 1 70 15 40 30 0.069 Units V/µs MHz Deg dB nV/ % Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics. Note 2: Applies to both single supply operation. Continuous short circuit operation at elevated ambient temperature can result in exceeding the maximum allowed junction temperature of 150˚C. Output currents in excess of 45mA over long term may adversely affect reliability. Note 3: The maximum power dissipation is a function of TJ(MAX), θJA, and TA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(MAX) – TA)θJA. All numbers apply for packages soldered directly into a PC board. Note 4: Typical value represent the most likely parametric norm. Note 5: All limits are guaranteed by testing or statistical analysis. Note 6: V+ = 5V. Connected as voltage follower with 5V step input. Number specified is the slower of the positive and negative slew rates. Note 7: Human body model, 1.5kΩ in series with 100pF. Machine model, 200Ω in series with 100pF. Simplified Schematic 20019302 5 www.national.com LMV301 Typical Performance Characteristics Unless otherwise specified, TA = 25˚C. Supply Current vs. Supply Voltage Output Negative Swing vs. Supply Voltage 20019359 20019360 Output Negative Swing vs. Supply Voltage Output Positive Swing vs. Supply Voltage 20019361 20019362 Output Positive Swing vs. Supply Voltage VOS vs. VCM 20019363 20019365 www.national.com 6 LMV301 Typical Performance Characteristics VOS vs. VCM Unless otherwise specified, TA = 25˚C. (Continued) VOS vs. VCM 20019366 20019367 Sourcing Current vs. Output Voltage Sinking Current vs. Output Voltage 20019368 20019369 Sourcing Current vs. Output Voltage Sinking Current vs. Output Voltage 20019370 20019371 7 www.national.com LMV301 Typical Performance Characteristics Sourcing Current vs. Output Voltage Unless otherwise specified, TA = 25˚C. (Continued) Sinking Current vs. Output Voltage 20019373 20019372 IBIAS Current vs. VCM Open Loop Frequency Response 20019364 20019353 Open Loop Frequency Response Open Loop Frequency Response 20019354 20019355 www.national.com 8 LMV301 Typical Performance Characteristics Open Loop Frequency Response Unless otherwise specified, TA = 25˚C. (Continued) Open Loop Frequency Response 20019356 20019357 Open Loop Frequency Response Noise vs. Frequency Response 20019358 20019374 Noise vs. Frequency Response Noise vs. Frequency Response 20019375 20019376 9 www.national.com LMV301 Typical Performance Characteristics Small Signal Response Unless otherwise specified, TA = 25˚C. (Continued) Large Signal Response 20019345 20019346 Small Signal Response Large Signal Response 20019347 20019348 Small Signal Response Large Signal Response 20019349 20019350 www.national.com 10 LMV301 Typical Performance Characteristics Small Signal Response Unless otherwise specified, TA = 25˚C. (Continued) Large Signal Response 20019352 20019351 11 www.national.com LMV301 Application Hints Compensating Input Capacitance The high input resistance of the LMV301 op amp allows the use of large feedback and source resistor values without losing gain accuracy due to loading. However, the circuit will be especially sensitive to its layout when these large value resistors are used. Every amplifier has some capacitance between each input and AC ground, and also some differential capacitance between the inputs. When the feedback network around an amplifier is resistive, this input capacitance (along with any additional capacitance due to circuit board traces, the socket, etc.) and the feedback resistors create a pole in the feedback path. In the following General Operational Amplifier circuit, Figure 1, the frequency of this pole is the following value of feedback capacitor is recommended: If the feedback capacitor should be: where CS is the total capacitance at the inverting input, including amplifier input capacitance and any stray capacitance from the IC socket (if one is used), circuit board traces, etc., and RP is the parallel combination of RF and RIN. This formula, as well as all formulae derived below, apply to inverting and non-inverting op amp configurations. When the feedback resistors are smaller than a few kΩ, the frequency of the feedback pole will be quite high, since CS is generally less than 10pF. If the frequency of the feedback pole is much higher than the “ideal” closed-loop bandwidth (the nominal closed-loop bandwidth in the absence of CS), the pole will have a negligible effect on stability, as it will add only a small amount of phase shift. However, if the feedback pole is less than approximately 6 to 10 times the “ideal” −3dB frequency, a feedback capacitor, CF, should be connected between the output and the inverting input of the op amp. This condition can also be stated in terms of the amplifier’s low frequency noise gain. To maintain stability a feedback capacitor will probably be needed if Note that these capacitor values are usually significantly smaller than those given by the older, more conservative formula: 20019306 CS consists of the amplifier’s input capacitance plus any stray capacitance from the circuit board and socket. CF compensates for the pole caused by CS and the feedback resistors. where FIGURE 1. General Operational Amplifier Circuit Using the smaller capacitor will give much higher bandwidth with little degradation of transient response. It may be necessary in any of the above cases to use a somewhat larger feedback capacitor to allow for unexpected stray capacitance, or to tolerate additional phase shifts in the loop, or excessive capacitive load, or to decrease the noise or bandwidth, or simply because the particular circuit implementation needs more feedback capacitance to be sufficiently stable. For example, a printed circuit board’s stray capacitance may be larger or smaller than the breadboard’s, so the actual optimum value for CF may be different from the one estimated using the breadboard. In most cases, the values of CF should be checked on the actual circuit, starting with the computed value. is the amplifier’s low frequency noise gain and GBW is the amplifier’s gain bandwidth product. An amplifier’s low frequency noise gain is represented by the formula regardless of whether the amplifier is being used in inverting or non-inverting mode. Note that a feedback capacitor is more likely to be needed when the noise gain is low and/or the feedback resistor is large. If the above condition is met (indicating a feedback capacitor will probably be needed), and the noise gain is large enough that: www.national.com 12 LMV301 Application Hints Capacitive Load Tolerance (Continued) Like many other op amps, the LMV301 may oscillate when its applied load appears capacitive. The threshold of oscillation varies both with load and circuit gain. The configuration most sensitive to oscillation is a unity gain follower. The load capacitance interacts with the op amp’s output resistance to create an additional pole. If this pole frequency is sufficiently low, it will degrade the op amp’s phase margin so that the amplifier is no longer stable. As shown in Figure 2, the addition of a small resistor (50Ω to 100Ω) in series with the op amp’s output, and a capacitor (5pF to 10pF) from inverting input to output pins, returns the phase margin to a safe value without interfering with lower frequency circuit operation. Thus, larger values of capacitance can be tolerated without oscillation. Note that in all cases, the output will ring heavily when the load capacitance is near the threshold for oscillation. 20019323 FIGURE 3. Compensating for Large Capacitive Loads with a Pull Up Resistor PRINTED-CIRCUIT-BOARD LAYOUT FOR HIGH-IMPEDANCE WORK It is generally recognized that any circuit which must operate with less than 100pA of leakage current requires special layout of the PC board. When one wishes to take advantage of the low bias current of the LMV301, typically less than 0.182pA, it is essential to have an excellent layout. Fortunately, the techniques for obtaining low leakages are quite simple. First, the user must not ignore the surface leakage of the PC board, even though it may sometimes appear acceptable low, because under conditions of the high humidity or dust or contamination, the surface leakage will be appreciable. To minimized the effect of any surface leakage, lay out a ring of foil completely surrounding the LMV301’s inputs and the terminals of capacitors, diodes, conductors, resistors, relay terminals, etc. connected to the op amp’s inputs. See Figure 4. To have a significant effect, guard rings should be placed on both the top and bottom of the PC board. The PC foil must then be connected to a voltage which is at the same voltage as the amplifier inputs, since no leakage current can flow between two points at the same potential. For example, a PC board trace-to-pad resistance of 1012Ω, which is normally considered a very large resistance, could leak 5pA if the trace were a 5V bus adjacent to the pad of an input. This would cause a 100 times degradation from the LMV301’s actual performance. However, if a guard ring is held within 5mV of the inputs, then even a resistance of 1011Ω would cause only 0.05pA of leakage current, or perhaps a minor (2:1) degradation of the amplifier performance. See Figure 5a, Figure 5b, Figure 5c for typical connections of guard rings for standard op amp configurations. If both inputs are active and at high impedance, the guard can be tied to ground and still provide some protection; see Figure 5d. 20019305 FIGURE 2. Rx, Cx Improve Capacitive Load Tolerance Capacitive load driving capability is enhanced by using a pull up resistor to V+ (Figure 3). Typically a pull up resistor conducting 500µA or more will significantly improve capacitive load responses. The value of the pull up resistor must be determined based on the current sinking capability of the amplifier with respect to the desired output swing. Open loop gain of the amplifier can also be affected by the pull up resistor. 20019377 FIGURE 4. Example, using the LMV301, of Guard Ring in P.C. Board Layout 13 www.national.com LMV301 Application Hints (Continued) 20019317 (a) Inverting Amplifier 20019318 (b) Non-Inverting Amplifier 20019319 (c) Follower 20019320 (d) Howland Current Pump FIGURE 5. Guard Ring Connections www.national.com 14 LMV301 Application Hints (Continued) The designer should be aware that when it is inappropriate to lay out a PC board for the sake of just a few circuits, there is another technique which is even better than a guard ring on a PC board: Don’t insert the amplifier’s input pin into the board at all, but bend it up in the air and use only air as an insulator. Air is an excellent insulator. In this case you may have to forego some of the advantages of PC board construction, but the advantages are sometimes well worth the effort of using point-to-point up-in-the-air wiring. See Figure 6 20019321 (Input pins are lifted out of PC board and soldered directly to components. All other pins connected to PC board.) FIGURE 6. Air Wiring 15 www.national.com LMV301 Typical Single-Supply Applications (V+ = 5.0 VDC) Low-Leakage Sample-and-Hold Power Amplifier 20019311 20019307 10Hz Bandpass Filter Sine-Wave Oscillator 20019312 fO = 10 Hz Q = 2.1 Gain = −8.8 10 Hz High-Pass Filter 20019309 Oscillator frequency is determined by R1, R2, C1, and C2: fosc = 1/2πRC, where R = R1 = R2 and C = C1 = C2. This circuit, as shown, oscillates at 2.0kHz with a peak-to-peak output swing of 4.5V. 1 Hz Square-Wave Oscillator 20019313 fc = 10 Hz d = 0.895 Gain = 1 2 dB passband ripple 1 Hz Low-Pass Filter (Maximally Flat, Dual Supply Only) 20019310 20019314 fc = 1 Hz d = 1.414 Gain = 1.57 www.national.com 16 LMV301 SC70-5 Tape Dimensions 20019396 SC70-5 Tape Format Tape Format Tape Section Leader (Start End) Carrier Trailer (Hub End) # Cavities 0 (min) 75 (min) 3000 250 125 (min) 0 (min) Cavity Status Empty Empty Filled Filled Empty Empty Cover Tape Status Sealed Sealed Sealed Sealed Sealed Sealed 17 www.national.com LMV301 SC70-5 Reel Dimensions 20019397 8mm Tape Size 7.00 330.00 A 0.059 1.50 B 0.512 13.00 C 0.795 20.20 D 2.165 55.00 N 0.331+ 0.059/−0.000 8.40 + 1.50/− 0.00 W1 0.567 14.40 W2 W1 + 0.078/−0.039 W1 + 2.00/−1.00 W3 www.national.com 18 LMV301 Low Input Bias Current, 1.8V Op Amp w/ Rail-to-Rail Output Physical Dimensions unless otherwise noted inches (millimeters) SC70-5 NS Package Number MAA05A LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: ap.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.