LP2960IN-5.0

LP2960 Adjustable Micropower 0.5A Low-Dropout Regulators April 1999 LP2960 Adjustable Micropower 0.5A Low-Dropout Regulators General Description The LP2960 is a micropower voltage regulator with very low dropout voltage (12 mV typical at 1 mA load and 470 mV typical at 500 mA load) and very low quiescent current (450 µA typical at 1 mA load). The LP2960 is ideally suited for battery-powered systems: the quiescent current increases only slightly at dropout, which prolongs battery life. The LP2960 retains all the desirable characteristics of the LP2953, and offers increased output current. The error flag goes low any time the output drops more than 5% out of regulation. Reverse battery protection is provided. The LP2960 requires only 10 µF of output capacitance for stability (5V version). The internal voltage reference is made available for external use, providing a low-T.C. reference with very good regulation characteristics. The parts are available in 16-pin plastic DIP and 16-pin surface mount packages. Features n n n n n n n n n n n n Output voltage adjusts from 1.23V–29V Guaranteed 500 mA output current 5V and 3.3V versions available 16-pin DIP and 16-pin SO packages Low dropout voltage Low quiescent current Tight line and load regulation Low temperature coefficient Current limiting and thermal protection Logic-level shutdown Can be wired for snap-ON and snap-OFF Reverse battery protection Applications n n n n High-efficiency linear regulator Regulator with under-voltage shutdown Low dropout battery-powered regulator Cellular telephones Block Diagram DS011962-1 © 1999 National Semiconductor Corporation DS011962 www.national.com Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Storage Temperature Range Operating Junction Temperature Range LP2960AI/LP2960I −65˚C to +150˚C Lead Temperature (Soldering, 5 sec.) Power Dissipation (Note 2) Input Supply Voltage Feedback Input Voltage (Note 3) Comparator Input Voltage (Note 4) Comparator Output Voltage (Note 4) ESD Rating (Note 15) 260˚C Internally Limited −20V to +30V −0.3V to +5V −0.3V to +30V −0.3V to +30V 1.5 kV −40˚C to +125˚C Electrical Characteristics Limits in standard typeface are for TJ = 25˚C, and limits in boldface type apply over the full operating temperature range. Unless otherwise specified: CIN = 4.7 µF, VIN = VO(NOM) + 1V, IL = 1 mA, COUT = 10 µF for 5V parts or COUT = 22 µF for 3.3V parts, Feedback pin is tied to VTAP pin, Output pin is tied to Sense pin, VS/D = 2V. Symbol VO Parameter Output Voltage (5V Versions) Output Voltage (3.3 Versions) Output Voltage Temperature Coefficient Output Voltage Line Regulation Output Voltage Load Regulation VIN − VO Conditions 1 mA ≤ IL ≤ 500 mA 1 mA ≤ IL ≤ 500 mA (Note 5) 20 VIN = [VO(NOM) + 1V] to 30V 0.06 (Note 6) 0.08 12 180 260 470 450 2.6 2.5 21 1.8 300 1000 0.05 en Output Noise Voltage @ IL = 100 mA (10 Hz–100kHz) COUT = 10 µF COUT = 47 µF COUT = 47 µF (Note 11) 2 Typ LP2960AI (Note 14) Min Max 5.038 5.070 3.325 3.346 130 0.2 0.5 0.16 0.30 30 50 250 350 350 450 600 800 600 750 4.0 5.0 8 10 35 40 3 5 400 1500 1600 0.2 4.962 4.930 3.275 3.254 LP2960I (Note 14) Min 4.925 4.880 3.250 3.221 Max 5.075 5.120 3.350 3.379 160 0.4 0.8 0.20 0.40 30 50 250 350 350 450 600 800 600 750 4.0 5.0 8 10 35 40 3 5 400 1500 1600 0.2 Units 5.0 3.3 V ppm/˚C % % Dropout Voltage (Note 7) IL = 1 mA IL = 100 mA IL = 200 mA IL = 500 mA mV IGND Ground Pin Current (Note 8) IL = 1 mA IL = 100 mA IL = 200 mA IL = 500 mA µA mA IGND Ground Pin Current at Dropout (Note 8) Ground Pin Current at Shutdown (Note 8) VIN = VO(NOM) − 0.5V IL = 100 µA VSD ≤ 1.1V RL = 0.5Ω (Note 10) mA µA mA %/W ILIMIT Current Limit Thermal Regulation 300 210 130 µV RMS www.national.com Electrical Characteristics Limits in standard typeface are for TJ = 25˚C, and limits in boldface type apply over the full operating temperature range. Unless otherwise specified: CIN = 4.7 µF, VIN = VO(NOM) + 1V, IL = 1 mA, COUT = 10 µF for 5V parts or COUT = 22 µF for 3.3V parts, Feedback pin is tied to VTAP pin, Output pin is tied to Sense pin, VS/D = 2V. (Continued) Symbol VREF Parameter Reference Voltage Reference Voltage Line Regulation Reference Voltage Load Regulation Reference Voltage Temperature Coefficient IB(FB) Feedback Pin Bias Current Output HIGH Leakage Output LOW Voltage VOH = 30V VIN = VO(NOM) − 1V IO(COMP) = 400 µA (Note 13) 0.05 IREF = 0–200 µA 0.45 (Note 5) 20 −20 −50 −70 1 2 250 400 −80 −100 −130 −200 −35 −25 −70 −35 −80 −100 −130 −200 −50 −70 1 2 250 400 −35 −25 −70 −35 ppm/˚C nA Conditions Typ LP2960AI (Note 14) Min 1.235 1.220 1.210 Max 1.250 1.265 0.1 0.30 0.6 0.9 LP2960I (Note 14) Min 1.210 1.195 Max 1.260 1.275 0.2 0.4 1.2 1.5 V % Units % DROPOUT DETECTION COMPARATOR IOH VOL 0.01 125 −60 −85 25 −18 −24 −60 −100 18 24 60 100 12 20 −15 −20 −60 −100 15 20 60 100 1 2 250 400 −15 −20 −60 −100 −18 −24 −60 −100 18 24 60 100 12 20 15 20 60 100 1 2 250 400 µA mV mV mV mV VTHR(max) Upper Threshold Voltage (Note 9) VTHR(min) Lower Threshold Voltage (Note 9) HYST VOS HYST IB Hysteresis Input Offset Voltage Hysteresis Input Bias Current (Note 9) (Referred to VREF) (Referred to VREF) VS/D = 0–5V SHUTDOWN INPUT ±5 10 −20 3 mV mV nA µA IOUT(S/D) Regulator Output Current (Note 12) in Shutdown AUXILIARY COMPARATOR VOS HYST IB IOH VOL Input Offset Voltage Hysteresis Input Bias Current Output HIGH Leakage Output LOW Voltage (Referred to VREF) (Referred to VREF) VCOMP = 0–5V VOH = 30V VCOMP = 1.3V VCOMP = 1.1V IO = 400 µA ±5 10 −20 0.01 125 mV mV nA µA mV Note 1: Absolute maximum ratings indicate limits beyond which damage to the component may occur. Electrical specifications do not apply when operating the device outside of its rated operating conditions. Note 2: The maximum allowable power dissipation is a function of the maximum junction temperature, TJ (max), the junction-to-ambient thermal resistance, θJ−A, and the ambient temperature, TA. The maximum allowable power dissipation at any ambient temperature is calculated using: Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. See APPLICATION HINTS for additional information on heatsinking and thermal resistance. Note 3: When used in dual-supply systems where the regulator load is returned to a negative supply, the output voltage must be diode-clamped to ground. 3 www.national.com Electrical Characteristics Limits in standard typeface are for TJ = 25˚C, and limits in boldface type apply over the full operating temperature range. Unless otherwise specified: CIN = 4.7 µF, VIN = VO(NOM) + 1V, IL = 1 mA, COUT = 10 µF for 5V parts or COUT = 22 µF for 3.3V parts, Feedback pin is tied to VTAP pin, Output pin is tied to Sense pin, VS/D = 2V. (Continued) Note 4: May exceed the input supply voltage. Note 5: Output or reference voltage temperature coefficient is defined as the worst case voltage change divided by the total temperature range. Note 6: Output voltage load regulation is measured at constant junction temperature using low duty cycle pulse testing. Two separate tests are performed, one for the load current range of 100 µA to 1 mA and one for the 1 mA to 500 mA range. Changes in output voltage due to heating effects are covered by the thermal regulation specification. Note 7: Dropout voltage is defined as the input to output differential at which the output voltage drops 100 mV below the value measured with a 1V differential. At very low values of programmed output voltage, the input voltage minimum of 2V (2.3V over temperature) must be observed. Note 8: Ground pin current is the regulator quiescent current. The total current drawn from the source is the sum of the ground pin current, output load current, and current through the external resistive divider (if used). Note 9: Dropout detection comparator threshold voltages are expressed in terms of a voltage differential measured at the Feedback terminal below the nominal reference voltage, which is the reference voltage measured with VIN = VO(NOM) + 1V. To express these thresholds in terms of output voltage change, multiply by the error amplifier gain which is VO/VREF = (R1 + R2)/R2 (see Basic Application Circuit). Note 10: Thermal regulation is the change in output voltage at a time T after a change in power dissipation, excluding load or line regulation effects. Specifications are for a 400 mA load pulse at VIN = VO(NOM) + 15V (6W pulse) for T = 10 ms. Note 11: Connect a 0.1 µF capacitor from the output to the feedback pin. Note 12: Vshutdown ≤ 1.1V, VIN < 30V, VOUT = 0V. Note 13: Two separate tests are performed for referenc e voltage line regulation, one covering 2.5V ≤ VIN ≤ VO(NOM) + 1V and the other test for VO(NOM) + 1V ≤ VIN ≤ 30V. Note 14: All room temperature limits are 100% production tested. All limits at temperature extremes are guaranteed via correlation using standard Statistical Quality Control (SQC) methods. All limits are used to calculate Average Outgoing Quality Level. Note 15: Human Body Model, 200 pF discharged through 1.5 kΩ. www.national.com 4 Basic Application Circuit DS011962-2 Connection Diagrams and Ordering Information 16-Pin Surface Mount Package 16-Pin DIP Package DS011962-3 DS011962-4 Top View Order Number LP2960IM-5.0, LP2960AIM-5.0, LP2960IM-3.3 or LP2960AIM-3.3 See NS Package Number M16A *Internally Connected to Power Ground Top View Order Number LP2960IN-5.0, LP2960AIN-5.0, LP2960IN-3.3 or LP2960AIN-3.3 See NS Package Number N16G 5 www.national.com Typical Performance Characteristics Unless otherwise specified: CIN = 4.7 µF, VIN = 6V, IL = 1 mA, COUT = 10 µF, Feedback pin is tied to VTAP pin, Output pin is tied to Sense pin, VS/D = 2V, VOUT = 5V. Ground Pin Current Ground Pin Current DS011962-5 DS011962-6 Ground Pin Current Ground Pin Current DS011962-7 DS011962-8 Ground Pin Current Dropout Characteristics DS011962-9 DS011962-10 www.national.com 6 Typical Performance Characteristics Unless otherwise specified: CIN = 4.7 µF, VIN = 6V, IL = 1 mA, COUT = 10 µF, Feedback pin is tied to VTAP pin, Output pin is tied to Sense pin, VS/D = 2V, VOUT = 5V. (Continued) Dropout Voltage vs Temperature Dropout Voltage vs Load Current DS011962-11 DS011962-12 Enable Transient Enable Transient DS011962-13 DS011962-14 Load Transient Load Transient DS011962-15 DS011962-16 7 www.national.com Typical Performance Characteristics Unless otherwise specified: CIN = 4.7 µF, VIN = 6V, IL = 1 mA, COUT = 10 µF, Feedback pin is tied to VTAP pin, Output pin is tied to Sense pin, VS/D = 2V, VOUT = 5V. (Continued) Current Limit vs Temperature Line Transient Response DS011962-17 DS011962-18 Line Transient Response Ripple Rejection DS011962-19 DS011962-20 Ripple Rejection Thermal Regulation DS011962-22 DS011962-21 www.national.com 8 Typical Performance Characteristics Unless otherwise specified: CIN = 4.7 µF, VIN = 6V, IL = 1 mA, COUT = 10 µF, Feedback pin is tied to VTAP pin, Output pin is tied to Sense pin, VS/D = 2V, VOUT = 5V. (Continued) Output Impedance Output Noise Voltage DS011962-23 DS011962-24 Feedback Bias Current Divider Resistance DS011962-25 DS011962-26 Error Output Voltage vs Input Voltage Dropout Detection Comparator Threshold Voltage DS011962-27 DS011962-28 9 www.national.com Schematic Diagram DS011962-38 www.national.com 10 Application Hints EXTERNAL CAPACITORS Bypass capacitors on the input and output of the LP2960 are required: without these capacitors, the part will oscillate. A capacitor (whose value is at least 4.7 µF) must be connected from the VIN pin to ground. If the input capacitor is located more than one inch away from the LP2960, the capacitor may have to be increased to 22 µF to assure stability. A capacitor is also required between VOUT and Ground, and the minimum amount of capacitance required here depends on output voltage. If the output voltage of the LP2960 is set to 5V, a minimum of 10 µF is needed in output capacitance. At 3.3V output, at least 22 µF is required to assure stability. ESR LIMIT: The ESR of the capacitor used on the LP2960 must be less than 0.7Ω throughout the entire operating temperature range to assure stability. The ESR of an aluminum eIectroIytic capacitor is typically only specified at 25˚C, and does not reflect the maximum ESR that can be expected to occur over the entire temperature range of the capacitor. Aluminum electrolytics show a marked increase in ESR at low temperatures (ESR can increase by a factor of 30 or more when going from 25˚C to −30˚C) which could lead to oscillation probIems in applications with very low ambient temperatures. Solid tantalum capacitors are recommended for use in such cases. Regulator instability can be caused by stray (board layout) capacitance appearing at the Feedback terminal. Oscillations from this effect are most Iikely to occur when very high value resistors are used to set the output voltage. Adding a 100 pF capacitor between the Output and Feedback pins and increasing the output capacitor to at least 22 µF will stop the osciIIations. MINIMUM LOAD The internal resistive divider in the LP2960 provides sufficient output loading for proper regulation. If externaI resistors are used to set the LP2960 output voltage, a minimum current of 5 µA through the externaI resistive divider is recommended. It should be noted that a minimum load current is specified in several of the test conditions listed under Electrical Characteristics, and this value of load current must be used to get correlation on these test limits. PROGRAMMING THE OUTPUT VOLTAGE The LP2960 regulator may be pin-strapped for operation at the nominal output voltage using its internal resistive divider by tying the Output and Sense pins together and also tying the Feedback and VTAP pins together. Alternatively, it may be programmed for any voltage between the 1.23V reference and the 30V maximum rating using an external pair of resistors (see Basic Application Circuit). The complete equation for the output voltage is: VOUT = VREF x (1 + R1/R2) + (IFB x R1) The term VREF is the 1 .23V reference and IFB is the Feedback pin bias current (−20 nA typical). The minimum recommended load current of 5 µA sets an upper limit of 240 kΩ on the value of R2 in cases where the regulator must work with no load (see Minimum Load). For best output accuracy, choosing R2 = 100 kΩ will reduce the error resulting from IFB to 0.17% while increasing the re11 www.national.com sistive divider current to 12 µA. Since the typicaI quiescent current of the LP2960 is 450 µA, this added current through R2 is negligible. DROPOUT VOLTAGE The dropout voltage of the regulator is defined as the minimum input-to-output voltage differential required for the output voltage to stay within 100 mV of the output voltage measured with a 1V differential. The dropout voltage is independent of the programmed output voltage. OUTPUT ISOLATION If the LP2960 output is connected to an active voltage source (such as a battery) the regulator input should not be shorted to ground, as this will cause a large current to flow from the battery into the LP2960 output lead. If the LP2960 input is left floating with the output connected to a battery, a small current (a few mA) will flow into the output lead. The “reverse” current flowing from the battery into the LP2960 output can be prevented by using a blocking diode between the output and the battery. REDUCING OUTPUT NOISE In reference applications it may be desirabIe to reduce the AC noise present on the output. One method is to reduce regulator bandwidth by increasing output capacitance. This is relatively inefficient, since large increases in capacitance are required to get significant improvement. Noise can be reduced more effectively by a bypass capacitor placed across R1 (refer to Basic Application Circuit). A 0.1 µF capacitor connected across R1 will reduce the high frequency gain of the circuit to unity, lowering the RMS output noise voltage from 210 µV to 130 µV (typical) using a 10 Hz–100 kHz bandwidth test measurement. Also, output noise is no longer proportional to the output voltage, so improvements are more pronounced at higher output voltages. IMPORTANT: Since the 0.1 µF capacitor reduces the AC gain of the LP2960 to unity, the output capacitance must be increased to at least 33 µF to assure regulator stability. DROPOUT DETECTION COMPARATOR The dropout detection comparator produces a logic “LOW” on the Error output whenever the LP2960 output drops out of regulation by more than about 5%. This figure results from the comparator’s built-in offset of 60 mV divided by the 1.23V reference (refer to block diagram). The “5% below nominal” trip level remains constant regardless of the programmed output voltage. An out-of-regulation condition can result from low input voltage, current limiting, or thermal limiting. The figure below gives a timing diagram showing the relationship between the output voltage, the Error output, and input voltage as the input voltage is ramped up and down to a regulator programmed for 5V output. Application Hints (Continued) Error Output Timing Diagram open-collector logic, a pull-up resistor (20 kΩ–100 kΩ recommended) should be connected from the Shutdown input to the regulator input. If the Shutdown input is driven from a source which actively pulls low and high (like an op-amp), the puIl-up resistor is not required, but may be used. If the Shutdown input is to be unused, the cost of the pull-up resistor can be saved by tying the Shutdown input directly to the regulator input. IMPORTANT: Since the Absolute Maximum Ratings state that the Shutdown input can not go more than 0.3V below ground, the reverse-battery protection feature which protects the regulator input is sacrificed if the Shutdown input is tied directly to the regulator input. If reverse-battery protection is required in an application, the pull-up resistor between the Shutdown input and the regulator input must be used. GROUND CONNECTIONS The pins designated GND (see Connection Diagrams) must be connected to the high-current ground point in the circuit. The GND pins are electrically connected (through the lead frame) to the die substrate, making them ideal for conducting ground current or heat (see Heatsinking). The parts in the surface-mount (M) package also have an Analog Ground pin, which is the ground point on the die for the regulator reference circuitry. Along with the Sense pin, the availability of the Analog Ground pin allows the designer the ability to use “remote” sensing and eliminate output voltage errors due to IR drops occurring along PC board traces. DS011962-29 *In shutdown mode, ERROR will go high if it has been pulled up to an external supply. To avoid this invalid response, pull-up to regulator output. **Exact value depends on dropout voltage. (See Application Hints) The Error signal becomes low as VIN exceeds about 1.3V. It goes high at about 5V input, where the output equals 4.75V. Since the dropout voltage is load dependent, the input voltage trip points will vary with load current, but the output voltage trip point does not. The comparator has an open-collector output which requires an external pull-up resistor. This resistor may be connected to the LP2960 output or another supply voltage. Best operation is obtained by connecting the pull-up to the LP2960 output. If the pull-up resistor is connected to an external 5V supply, the error flag will incorrectly signal “HIGH” whenever VIN < 1.3V (see Error Output Timing Diagram). In selecting a value for the pull-up resistor, note that while the output can sink 400 µA, this current adds to battery drain. Suggested values range from 100 kΩ–1 MΩ. The resistor is not required if the output is unused. If a large output capacitance is used, a false logic “HIGH” can be generated when VIN ≈1.3V. In this case, the error output becomes a high impedance, causing the voltage at the error output to rise to its pull-up value. If the pull-up resistor is connected to VOUT, the error output can rise to 1.2V (which is a logic “HIGH” signal incorrectly signifying the output is in regulation). The user may wish to divide down the error flag voltage using equal-value resistors (10 kΩ suggested) to ensure a low-level logic signal during any fault condition, while still allowing a valid high logic level during normal operation. AUXILIARY COMPARATOR The LP2960 contains an auxiliary comparator whose inverting input is connected to the 1.23V reference. The auxiIiary comparator has an open-collector output whose electrical characteristics are similar to the dropout detection comparator. The non-inverting input and output are brought out for external connections. SHUTDOWN INPUT A logic-level signal will shut off the regulator output when a “LOW” ( < 1.2V) is applied to the Shutdown input. To prevent possible mis-operation, the Shutdown input must be actively terminated. If the input is driven from www.national.com 12 IMPORTANT: The Analog Ground pin must be connected to circuit ground at some point for the regulator to operate. If remote sensing is not needed, the Analog Ground pin can simply be pin-strapped to the adjacent GND pin. HEATSINKING A heatsink may be required with the LP2960 depending on the maximum power dissipation and maximum ambient temperature of the application. Under alI possible operating conditions, the junction temperature must be within the range specified under Absolute Maximum Ratings. To determine if a heatsink is required, the power dissipated by the regulator, PD, must be calculated. The figure below shows the voltages and currents which are present in the circuit, as welI as the formula for calcuIating the power dissipated in the regulator: Power Dissipation Diagram DS011962-30 Application Hints (Continued) Heat Sink Foil Patterns The next parameter which must be calculated is the maximum allowable temperature rise, TR (max). This is calculated by using the formula: TR (max) = TJ (max) − TA (max) where: TJ (max) is the maximum allowable junction temperature, which is 125˚C for commercial grade parts. TA (max) is the maximum ambient temperature which will be encountered in the application. Using the calculated values for TR (max) and PD, the maximum allowable value for the junction-to-ambient thermal resistance, θ(J−A), can now be found: θ(J−A) = TR (max)/PD The heatsink for the LP2960 is made using the PC board copper, with the heat generated on the die being conducted through the lead frame and out to the pins which are soldered to the PC board. The GND pins are the only ones capable of conducting any significant amount of heat, as they are internally attached to the lead frame on which the die is mounted. The figure below shows recommended copper foil patterns to be used for heatsinking the DIP and Surface Mount packages: DS011962-31 The table below shows measured values of θ(J−A) for a PC board with 1 ounce copper weight: Package DIP Surface Mount L (in.) 1 2 1 2 H (in.) 0.5 0.2 0.5 0.2 θJ−A(˚C/W) 50 52 72 74 As the heat must transfer from the copper to the surrounding air, best results (lowest θJ−A) will be obtained by using a surface copper layer with the solder resist opened up over the heatsink area. If an internal copper layer of a multi-layer board is used for heatsinking, the board material acts as an insulator, inhibiting heat transfer and increasing θJ−A. As with any heatsink, increasing the airflow across the board will significantly improve the heat transfer. 13 www.national.com Typical Applications Low T.C. Current Sink 5V Bus Current Limiter with Load Fault Indicator DS011962-33 output current. Current limits at a maximum of 1000 mA (typical). **Select R1 so that the comparator input voltage is 1.23V at the output voltage which corresponds to the desired fault current value. *Output voltage equals +VIN minus dropout voltage, which varies with DS011962-32 5V Regulator with Error Flags for Low BATTERY and OUT OF REGULATION 5V Regulator with Snap-ON/Snap-OFF Feature and Hysteresis DS011962-34 *Connect to Logic or µP control inputs. DS011962-35 LOW BATT flag warns the user that the battery has discharged down to about 5.8V, giving the user time to recharge the battery or power-down some hardware with high power requirements. The output is still in regulation at this time. OUT OF REGULATION flag indicates when the battery is almost completely discharged, and can be used to initiate a power-down sequence. *Turns ON at VIN = 5.87V Turns OFF at VIN = 5.64V (for component values shown) www.national.com 14 Typical Applications (Continued) Timing Diagram for Timed Power-On Reset 5V Regulator with Timed Power-On Reset DS011962-37 DS011962-36 *RT = 1 Meg, CT = 0.1 µF 15 www.national.com Physical Dimensions inches (millimeters) unless otherwise noted Order Number LP2960IM-5.0, LP2960AIM-5.0, LP2960IM-3.3 or LP2960AIM-3.3 NS Package Number M16A Order Number LP2960IN-5.0, LP2960AIN-5.0, LP2960IN-3.3 or LP2960AIN-3.3 NS Package Number N16G www.national.com 16 LP2960 Adjustable Micropower 0.5A Low-Dropout Regulators Notes LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 1 80-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 1 80-530 85 85 English Tel: +49 (0) 1 80-532 78 32 Français Tel: +49 (0) 1 80-532 93 58 Italiano Tel: +49 (0) 1 80-534 16 80 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: sea.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.