LP3913SQ-AB

LP3913 Power Management IC for Flash Memory Based Portable Media Players ADVANCE INFORMATION November 2006 LP3913 Power Management IC for Flash Memory Based Portable Media Players General Description The LP3913 is a programmable system power management unit that is optimized for Flash Memory based Portable Media Players. The LP3913 incorporates 2 low-dropout LDO voltage regulators, 3 integrated Buck DC/DC converters with Dynamic Voltage Scaling (DVS), a 4-channel 8-bit A/D converter, and a dual source Li-Ion/polymer battery charger. The charger has the capability to charge and maintain a single cell battery from a regulated wall adapter or USB power. When both USB and adapter sources are present, then the adapter source takes precedence and switching between USB and adapter power sources is seamless. In addition, the battery charger supports power routing, which allows system usage immediately after an external power source has been detected. The LP3913 also incorporates some advanced battery management functions such as battery temperature measurement, reverse current blocking for USB, LED charger status indication, thermally regulated internal power FETs, battery voltage monitoring, over-current protection and a 10 hour safety timer. The 4-channel A/D converter measures the battery voltage and charge current, which can be used for fuel gauging. Two undedicated channels can be used to measure other analog parameters such as discharge current, battery temperature, keyboard resistor scanning and more. The various IC parameters are programmable through a 400 kHz I2C compatible interface. The LP3913 is available in a thermally-enhanced 6x6x0.8 mm 48 LLP package and operates over an ambient temperature range of –40°C to +85°C. Features ■ 2 low-dropout regulators -- LDO1 is used for general purpose applications, LDO2 is used for low-noise analog applications. Both LDOs have programmable output voltages. Green and Red LED charger status drivers 4-channel 8-bit dual slope a/d converter 3 High-efficiency DVS Buck converters 400 kHz I2C compatible interface Linear constant-current / constant-voltage charger for single cell lithium-ion batteries USB and Adapter charging System power supply management 6x6x0.8mm 48 LLP package Voltage and thermal supervisory circuits Continuous battery voltage monitoring Interrupt Request output with 8 sources LP3913 is pin for pin and software compatible with the LP3910 Hard Drive based PMIC ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Key Specifications ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ LDO1: 150 mA, 1.2V–3.3V LDO2: 150 mA, 1.3V–3.3V Buck1: 600 mA, 0.8V–2.0V Buck2: 600 mA, 1.8V–3.3V Buck3: 500 mA, 1.8V–3.3V 50 mΩ battery path resistance 100 mA–1000 mA full-rate charge current using wall adapter Selectable 0.05C and 0.1C EOC current USB current limit of 100 mA, 500 mA, and 800 mA USB pre-qual current of 50 mA Selectable 4.1V, 4.2V or 4.38V battery termination voltages 0.35% battery termination accuracy ±1 LSB INL/DNL on 8-bit a/d converter Applications ■ Flash-based portable media players ■ Portable gaming devices ■ Portable navigation systems © 2006 National Semiconductor Corporation 300001 www.national.com LP3913 Typical Application Circuit 30000101 FIGURE 1. Application Diagram www.national.com 2 LP3913 Connection Diagram Device Connection Diagram 30000102 48 LLP Package (Top View) SQF48A The physical placement of the package marking will vary from part to part. (*) UZXYTT format: ‘U’ – wafer fab code; ‘Z’ – assembly code; ‘XY’ 2 digit date code; ‘TT’ – die run code See http://www.national.com/quality/marking_conventions.html for more information on marking information. Ordering Information Order Number LP3913SQ-AB LP3913SQX-AB Package Type 48-lead LLP 48-lead LLP NSC Package Drawing SQF48A SQF48A Top Mark LP3913SQ-AB LP3913SQX-AB Supplied As 250 tape & reel 3000 tape & reel Device Default Options Order Number LP3910SQ-AB LP3910SQX-AB LDO1 2.0V 2.0V LDO2 3.3V 3.3V Buck1 1.2V 1.2V Buck2 3.3V 3.3V BuckBoost 1.8V 1.8V Other Options Standard Defaults Standard Defaults 3 www.national.com LP3913 Physical Dimensions inches (millimeters) unless otherwise noted SQF48A Package: 6x6x0.8mm 48-Pin LLP Package with 0.4mm Pitch www.national.com 4 LP3913 Notes 5 www.national.com LP3913 Power Management IC for Flash Memory Based Portable Media Players Notes THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION (“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright© 2006 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530-85-86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +49 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 www.national.com