LP3941LQA

LP3941A Cellular Phone Power Management Unit May 2004 LP3941A Cellular Phone Power Management Unit General Description LP3941A is a complete power management IC designed for a cellular phone. It contains 11 low noise low dropout regulators, a linear charger for Li-Ion battery, a backup battery charger, real time clock supply regulator, three open drain drivers, two comparators and high speed I2C compatible serial interface to program individual regulator output voltages as well as on/off control. LP3941 is available in a LLP48 package. n Three open drain drivers to control a RGB LED n I2C compatible serial interface for maximum flexibility Applications n GSM/EDGE cellular handsets n Wideband CDMA cellular handsets Key Specifications n n n n 3.0V to 5.5V Input Voltage Range 27 µVRMS Output noise 2% (typical) Output Voltage Accuracy 1% Charger Voltage Accuracy Features n n n n 11 low dropout, low noise LDOs. Dedicated low current LDO for real time clock supply. Back-up battery charger A constant current / constant voltage battery charger controller with charge status indication via I2C compatible interface. Typical Application 20094501 © 2004 National Semiconductor Corporation DS200945 www.national.com LP3941A Connection Diagrams and Package Mark Information 48-Pin Leadless Leadframe Package See NS Package Number LQA48B 20094503 20094502 Note: Circle marks pin 1 position. Pin 1 name is N/C. Bottom View Top View 20094517 Note: The actual physical placement of the package marking will vary from part to part. The package markings “UZYY” designate assembly and manufacturing information. “TT” is a NSC internal code for die traceability. Both will vary considerably. “3941LQA” identifies the device. Package Mark — Top View Ordering Information Order Number LP3941LQ-A LP3941LQX-A Package Marking LP3941LQA LP3941LQA Supplied As 250 units, Tape-and-Reel 2500 units, Tape-and-Reel Note: *See LP3941A register table and LDO programming table for information on the default voltages for LP3941A. www.national.com 2 LP3941A Pin Description Pin # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Name N/C AGND3 VO8 IN5 VO9 VO10 IN6 VO11 DGND VO3 IN2 VO2 IN1 VO1 PS-HOLD BU_BAT VRTC IN (COMP1) OUT (COMP1) AGND1 IN (COMP2) OUT (COMP2) REF-BYP VO7 VO6-EN IN4 VO6 VO5 IN3 VO4 BSNS ON I/O G O I O O I O G O I O I O I I O I O G I O I O I I O O I O I O Type G A P A A P A G A P A P A D A A A A G A A A A D P A A P A A OD Not used. Connect to ground. Analog ground pin. LDO 8 Output Input power terminal to LDO’s. Must be connected to IN1–4 and IN6. LDO 9 output. LDO 10 output. Input power terminal to LDO’s. Must be connected to IN1–5. LDO 11 output. Ground pin. LDO 3 output. Input power terminal to LDO’s. Must be connected to IN1 and IN3–6. LDO 2 output. Input power terminal to LDO’s. Must be connected to IN2–6. LDO 1 output. Active low off key initiated by the micro controller. Back-up battery connection. RTC_LDO output. Non-inverting inout of the comparator 1. Output of the comparator 1. Analog ground pin. Non-inverting input of the comparator 2. Output of the comparator 2. Reference bypass capacitor. LDO 7 output. LDO 6 on/off pin. Internal pull-down resistor of 1 MΩ. Input power terminal to LDO’s. Must be connected to IN1–3 and IN5–6. LDO 6 output. LDO 5 output. Input power terminal to LDO’s. Must be connected to IN1–2 and IN4–6. LDO 4 output. Main battery ID resistor connection. Inverted open drain output signal of the ON input. Pulled low when ON is pulled high and open drain when ON is pulled low. There is no significant delay between the ON signal going high and ON pin going low. The delay between ON signal going low and ON pin is determined by the pull up current and capacitance connected to this pin. Battery voltage sense pin. Should be connected as close to the battery’s + terminal as possible. Gate drive to the external MOSFET. Battery supply input terminal. Must have 10 µF ceramic capacitor to GND. LDO 5 on/off pin. Internal pull down resistor of 1 MΩ. RTC_ALARM input. Active high power On/Off key. This pin is pulled to GND by an internal 200 kΩ resistor. Active high Hands Free connection signal. This pin has an internal 200 kΩ pull down resistor. Charger input from a current limited power source. Must have a 1 µF ceramic capacitor to GND. Charge current sense resistor. Reset output. Active low. (See Power Up Timing Diagram.) Description 33 34 35 36 37 38 39 40 41 42 BATTSENSE Drive BATT VO5-EN RTC_ALARM ON HF_PWR CHG_IN ISENSE RESET I O O I I I I I O O A A A D D D D P A OD 3 www.national.com LP3941A Pin Description Pin # 43 44 45 46 47 48 A: Analog Pin (Continued) I/O G I I/O O O O G: Ground Pin Name AGND2 SCL SDA LED1 LED2 LED3 D: Digital Pin Type G D D OD OD OD Analog ground pin. Serial interface clock input. Description Serial interface data input/output. LED driver output pin. LED driver output pin. LED driver output pin. I: Input Pin I/O: Input/Output Pin O: Output Pin OD: Open Drain Pin P: Power Pin www.national.com 4 LP3941A Absolute Maximum Ratings 2) (Notes 1, Maximum Continuous Power Dissipation (PD_MAX) (Note 3) Junction Temperature (TJ-MAX) Storage Temperature Range Maximum Lead Temperature (Soldering) ESD Ratings (Note 5) All Pins 2 kV HBM 200V MM 3.07W 150˚C −65˚C to +150˚C (Note 4) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. CHG-IN IN1–6, BATT, SDA, SCL, ON, HF-PWR, PS-HOLD, SYS, COMP1_IN, COMP2_IN, CHG_IN, BSNS, VO5-EN, VO6-EN, LED1–3, RTC_ALARM, BU_BAT, VRTC, RESET, BATTSENSE. REFBYP, ON, PS-HOLD, COMP1_OUT, COMP2_OUT to GND VO1 to GND VO2, VO3 to GND VO4, VO5 to GND VO6, VO7 to GND VO8, VO9 to GND VO10, VO11 to GND GND to GND SLUG −0.3V to +12V Operating Ratings (Notes 1, 2) −0.3V to +6V VIN VEN Junction Temperature (TJ) Range −0.3V to +VBAT + 0.3V −0.3V to +VIN1 + 0.3V −0.3V to +VIN2 + 0.3V −0.3V to +VIN3 + 0.3V −0.3V to +VIN4 + 0.3V −0.3V to +VIN5 + 0.3V −0.3V to +VIN6 + 0.3V Ambient Temperature (TA) Range (Note 6) 3.0V to 6.0V 0V to (VIN + 0.3V) −40˚C to +125˚C −40˚C to +85˚C Thermal Properties (Note 7) Junction-to-Ambient Thermal Resistance (θJA) 26˚C/W ± 0.3V Electrical Characteristics Unless otherwise noted, VIN = 2.5V to 5.5V, CIN (IN1–6) = 4.7 µF, COUT (VO1 and VO9) = 4.7 µF, COUT (VO2, VO3, VO7, VO8, VO10 and VO11) = 2.2 µF, COUT (VO4 to VO6) = 1 µF, COUT (VRTC) = 1 µF ceramic, CBYP = 0.1 µF. Typical values and limits appearing in normal type apply for TJ = 25˚C. Limits appearing in boldface type apply over the entire junction temperature range for operation, −40 to +125˚C. (Notes 2, 8, 9, 10) Symbol IQ Parameter Shutdown Supply Current Condition VBATT = 2.1V, UVLO on, internal logic generator on, VRTC off, all other circuits off. VBATT = 3.6V, LDOs VO1, VO3 and VO5 on, back-up battery charger and VRTC on, charger disconnected, comparator 1 & 2 on. VBATT = 3.6V, All LDOs on, charger disconnected. VBATT Rising VBATT Falling VBATT Falling Edge 2.91 2.15 1 Min Typ 14 Max Units µA No Load Supply Current, LDO 1 & 3 & 5 on 310 µA No Load Supply Current BATTERY UNDER VOLTAGE LOCKOUT VUVLO-R VUVLO-F VTH-POR Under Voltage Lock-Out Under Voltage Lock-Out Power-On Reset Threshold Threshold Hysteresis OUTPUT CAPACITORS COUT Capacitance ESR Input Low Level 500 µA 3.1 2.49 1.7 160 10 3.32 2.85 2.3 V V V THERMAL SHUTDOWN ˚C 1 5 PS-HOLD, ON, BSNS, HF-PWR, RTC_ALARM, SDA, SCL, VO5-EN, VO6-EN. 2.5V ≤ VBATT ≤ 5.5V 20 500 µF mΩ LOGIC AND CONTROL INPUTS VIL 0.4 V 5 www.national.com LP3941A Electrical Characteristics (Continued) Unless otherwise noted, VIN = 2.5V to 5.5V, CIN (IN1–6) = 4.7 µF, COUT (VO1 and VO9) = 4.7 µF, COUT (VO2, VO3, VO7, VO8, VO10 and VO11) = 2.2 µF, COUT (VO4 to VO6) = 1 µF, COUT (VRTC) = 1 µF ceramic, CBYP = 0.1 µF. Typical values and limits appearing in normal type apply for TJ = 25˚C. Limits appearing in boldface type apply over the entire junction temperature range for operation, −40 to +125˚C. (Notes 2, 8, 9, 10) Parameter Input High Level Condition PS-HOLD, ON, BSNS, HF-PWR, RTC_ALARM, SDA, SCL, VO5-EN, VO6-EN. 2.5V ≤ VBATT ≤ 5.5V SDA, SCL 0V ≤ VIN ≤ 5.5V 0V ≤ VIN ≤ VBATT Min Typ Max Units Symbol VIH LOGIC AND CONTROL INPUTS 2.0 V IIL Logic Input Current PS-HOLD Input Current −5 −5 200 1700 +5 +5 µA µA kΩ kΩ RIN ON, HF_PWR Pull-Down Resistance to GND VO5-EN, VO6-EN, RTC_ALARM Pull Down Resistance to GND LOGIC AND CONTROL OUTPUTS VOL ILEAKAGE IO-MAX ON Output Low Level ON Open Drain Leakage ON, RESET, OUT (COMP1), OUT (COMP2) Output Maximum Sink/Source Current ISINK = 1 mA VON = 4.2V 0.4 5 5 V µA mA VO1 LDO Electrical Characteristics Unless otherwise noted, VIN = VBATT = 3.6V. Typical values and limits appearing in normal type apply for TJ = 25˚C. Limits appearing in boldface type apply over the entire junction temperature range for operation, −40 to +85˚C. (Notes 2, 8, 9) Symbol VOUT Accuracy VOUT Range IOUT Parameter Output Voltage Programmable Output Voltage Range Output Current Output Current Limit VIN–VOUT ∆VOUT Dropout Voltage Line Regulation Load Regulation eN PSRR COUT tSTART-UP Output Noise Voltage Power Supply Ripple Rejection Ratio Output Capacitance Output Capacitor ESR Start-Up Time from Shutdown ON-signal Condition 1 mA ≤ IOUT ≤ 200 mA, VOUT = 2.2V 3.0V ≤ VBATT = VIN ≤ 5.5V 0 µA ≤ IOUT ≤ 200 mA Programming Resolution = 100 mV (VOUT + 0.25V, 3.0V)MAX ≤ VBATT VBATT = VIN ≤ 5.5V VOUT = 0V IOUT = 100 mA (VOUT + 0.25V, 3.0V)MAX ≤ VBATT VBATT = VIN ≤ 5.5V, IOUT = 100 mA VIN = 3.6V, 1 mA ≤ IOUT ≤ 200 mA 10 Hz ≤ f ≤ 100 kHz, COUT = 4.7 µF f = 217 Hz, COUT = 4.7 µF 1 mA ≤ IOUT ≤ 200 mA COUT = 4.7 µF, IOUT = 200 mA (Note 10) 2 5 80 120 780 70 3 10 27 60 20 500 180 µVRMS dB µF mΩ µs 254 mV mV Min −3 1.5 Typ Max +3 3.0 200 Units % V ± 1.0 1.8 mA Note: This LDO will be ON after start up by default. Note: (VOUT + 0.25V, 3.0V)MAX means greater of the two. That is 3.0V if VOUT < 2.75V. Note: The PMU can switch off if battery voltage is below 3.0V due to under voltage lockout designed to protect the battery from excessive discharge at low voltages. Note: The start-up time (tSTART-UP) is defined as the time between the rising edge of ON-, HF_PWR-, RTC ALARM- or CHG_IN- pins going high and activating the power-up sequence of the LP3941A. www.national.com 6 LP3941A VO2 LDO Electrical Characteristics Unless otherwise noted, VIN = VBATT = 3.6V. Typical values and limits appearing in normal type apply for TJ = 25˚C. Limits appearing in boldface type apply over the entire junction temperature range for operation, −40 to +125˚C. (Notes 2, 8, 9) Symbol VOUT Accuracy VOUT Range IOUT Parameter Output Voltage Programmable Output Voltage Range Output Current Output Current Limit VIN–VOUT ∆VOUT Dropout Voltage Line Regulation Load Regulation eN PSRR IGND COUT tSTART-UP Output Noise Voltage Power Supply Ripple Rejection Ratio Ground Current Output Capacitance Output Capacitor ESR Start-Up Time from Shutdown Condition 1 mA ≤ IOUT ≤ 200 mA, VOUT = 2.2V 3.0V ≤ VBATT = VIN ≤ 5.5V 0 µA ≤ IOUT ≤ 200 mA Programming Resolution = 100 mV (VOUT + 0.25V, 3.0V)MAX ≤ VBATT VBATT = VIN ≤ 5.5V VOUT = 0V IOUT = 75 mA (VOUT + 0.25V, 3.0V)MAX ≤ VBATT VBATT = VIN ≤ 5.5V, IOUT = 75 mA VIN = 3.6V, 1 mA ≤ IOUT ≤ 150 mA 10 Hz ≤ f ≤ 100 kHz, COUT = 2.2 µF f = 217 Hz, COUT = 2.2 µF IOUT = 100 µA 0 mA ≤ IOUT ≤ 150 mA COUT = 2.2 µF, IOUT = 150 mA (Note 10) 2 5 60 540 30 3 12 27 57 30 20 500 41 µVRMS dB µA µF mΩ µs 174 mV mV Min −3 1.5 Typ Max +3 3.0 150 Units % V ± 1.0 2.8 mA VO3 LDO Electrical Characteristics Unless otherwise noted, VIN = VBATT = 3.6V. Typical values and limits appearing in normal type apply for TJ = 25˚C. Limits appearing in boldface type apply over the entire junction temperature range for operation, −40 to +125˚C. (Notes 2, 8, 9) Symbol VOUT Accuracy VOUT Range IOUT Parameter Output Voltage Programmable Output Voltage Range Output Current Output Current Limit VIN–VOUT ∆VOUT Dropout Voltage Line Regulation Load Regulation eN PSRR IGND COUT tSTART-UP Output Noise Voltage Power Supply Ripple Rejection Ratio Ground Current Output Capacitance Output Capacitor ESR Start-Up Time from Shutdown Condition 1 mA ≤ IOUT ≤ 150 mA, VOUT = 2.7V 3.0V ≤ VBATT = VIN ≤ 5.5V 0 µA ≤ IOUT ≤ 150 mA Programming Resolution = 100 mV (VOUT + 0.25V, 3.0V)MAX ≤ VBATT VBATT = VIN ≤ 5.5V VOUT = 0V IOUT = 75 mA (VOUT + 0.25V, 3.0V)MAX ≤ VBATT VBATT = VIN ≤ 5.5V, IOUT = 75 mA VIN = 3.6V, 1 mA ≤ IOUT ≤ 150 mA 10 Hz ≤ f ≤ 100 kHz, COUT = 2.2 µF f = 217 Hz, COUT = 2.2 µF IOUT = 500 µA 0 mA ≤ IOUT ≤ 150 mA COUT = 2.2 µF, IOUT = 150 mA (Note 10) 2 5 60 520 30 3 12 27 56 30 20 500 41 µVRMS dB µA µF mΩ µs 156 mV mV Min −3 2.5 Typ Max +3 3.2 150 Units % V ± 1.0 3.0 mA Note: This LDO will be ON after start-up by default. It can be disabled via the register file. 7 www.national.com LP3941A VO4 LDO Electrical Characteristics Unless otherwise noted, VIN = VBATT = 3.6V. Typical values and limits appearing in normal type apply for TJ = 25˚C. Limits appearing in boldface type apply over the entire junction temperature range for operation, −40 to +125˚C. (Notes 2, 8, 9) Symbol VOUT Accuracy VOUT Range IOUT Parameter Output Voltage Programmable Output Voltage Range Output Current Output Current Limit VIN–VOUT ∆VOUT Dropout Voltage Line Regulation Load Regulation eN PSRR IGND COUT tSTART-UP Output Noise Voltage Power Supply Ripple Rejection Ratio Ground Current Output Capacitance Output Capacitor ESR Start-Up Time from Shutdown Condition 1 mA ≤ IOUT ≤ 50 mA, VOUT = 2.2V 3.0V ≤ VBATT = VIN ≤ 5.5V 0 µA ≤ IOUT ≤ 50 mA Programming Resolution = 100 mV (VOUT + 0.25V, 3.0V)MAX ≤ VBATT VBATT = VIN ≤ 5.5V VOUT = 0V IOUT = 25 mA (VOUT + 0.25V, 3.0V)MAX ≤ VBATT VBATT = VIN ≤ 5.5V, IOUT = 25 mA VIN = 3.6V, 1 mA ≤ IOUT ≤ 50 mA 10 Hz ≤ f ≤ 100 kHz, COUT = 1.0 µF f = 217 Hz, COUT = 1.0 µF IOUT = 100 µA 0 µA ≤ IOUT ≤ 50 mA COUT = 1.0 µF, IOUT = 50 mA (Note 10) 1 5 60 140 7 3 4 27 56 30 20 500 31 µVRMS dB µA µF mΩ µs 90 mV mV Min −3 1.5 Typ Max +3 3.0 50 Units % V ± 1.0 3.0 mA VO5 LDO Electrical Characteristics Unless otherwise noted, VIN = VBATT = 3.6V. Typical values and limits appearing in normal type apply for TJ = 25˚C. Limits appearing in boldface type apply over the entire junction temperature range for operation, −40 to +125˚C. (Notes 2, 8, 9) Symbol VOUT Accuracy VOUT Range IOUT Parameter Output Voltage Programmable Output Voltage Range Output Current Output Current Limit VIN–VOUT ∆VOUT Dropout Voltage Line Regulation Load Regulation eN PSRR IGND COUT tSTART-UP Output Noise Voltage Power Supply Ripple Rejection Ratio Ground Current Output Capacitance Output Capacitor ESR Start-Up Time from Shutdown Condition 1 mA ≤ IOUT ≤ 50 mA, VOUT = 2.2V 3.0V ≤ VBATT = VIN ≤ 5.5V 0 µA ≤ IOUT ≤ 50 mA Programming Resolution = 100 mV (VOUT + 0.25V, 3.0V)MAX ≤ VBATT VBATT = VIN ≤ 5.5V VOUT = 0V IOUT = 25 mA (VOUT + 0.25V, 3.0V)MAX ≤ VBATT VBATT = VIN ≤ 5.5V, IOUT = 25 mA VIN = 3.6V, 1 mA ≤ IOUT ≤ 50 mA 10 Hz ≤ f ≤ 100 kHz, COUT = 1.0 µF f = 217 Hz, COUT = 1.0 µF IOUT = 100 µA 0 µA ≤ IOUT ≤ 50 mA COUT = 1.0 µF, IOUT = 50 mA (Note 10) 1 5 60 160 7 3 4 27 56 30 20 500 31 µVRMS dB µA µF mΩ µs 90 mV mV Min −3 2.5 Typ Max +3 3.2 50 Units % V ± 1.0 2.8 mA Note: This LDO will be ON after start-up by default. Note: This LDO has an external active high enable pin, VO5-EN as well as the internal register enable bit. The LDO is on if either of these is “1” (OR-function). The enable bit is “1” by default and can be disabled via the register file. www.national.com 8 LP3941A VO6 LDO Electrical Characteristics Unless otherwise noted, VIN = VBATT = 3.6V. Typical values and limits appearing in normal type apply for TJ = 25˚C. Limits appearing in boldface type apply over the entire junction temperature range for operation, −40 to +125˚C. (Notes 2, 8, 9) Symbol VOUT Accuracy VOUT Range IOUT Parameter Output Voltage Programmable Output Voltage Range Output Current Output Current Limit VIN–VOUT ∆VOUT Dropout Voltage Line Regulation Load Regulation eN PSRR IGND COUT tSTART-UP Output Noise Voltage Power Supply Ripple Rejection Ratio Ground Current Output Capacitance Output Capacitor ESR Start-Up Time from Shutdown Condition 1 mA ≤ IOUT ≤ 50 mA, VOUT = 2.7V 3.0V ≤ VBATT = VIN ≤ 5.5V 0 µA ≤ IOUT ≤ 50 mA Programming Resolution = 100 mV (VOUT + 0.25V, 3.0V)MAX ≤ VBATT VBATT = VIN ≤ 5.5V VOUT = 0V IOUT = 25 mA (VOUT + 0.25V, 3.0V)MAX ≤ VBATT VBATT = VIN ≤ 5.5V, IOUT = 25 mA VIN = 3.6V, 1 mA ≤ IOUT ≤ 50 mA 10 Hz ≤ f ≤ 100 kHz, COUT = 1.0 µF f = 217 Hz, COUT = 1.0 µF IOUT = 100 µA 0 µA ≤ IOUT ≤ 50 mA COUT = 1.0 µF, IOUT = 50 mA (Note 10) 1 5 60 170 7 3 4 27 56 30 20 500 31 µVRMS dB µA µF mΩ µs 90 mV mV Min −3 2.5 Typ Max +3 3.2 50 Units % V ± 1.0 2.8 mA Note: This LDO has an external active high enable pin, VO6-EN as well as an internal register enable bit. The LDO is on if either of these is “1” (OR-function). The enable bit is “0” by default and can be enabled via the register file. VO7 LDO Electrical Characteristics Unless otherwise noted, VIN = VBATT = 3.6V. Typical values and limits appearing in normal type apply for TJ = 25˚C. Limits appearing in boldface type apply over the entire junction temperature range for operation, −40 to +125˚C. (Notes 2, 8, 9) Symbol VOUT Accuracy VOUT Range IOUT Parameter Output Voltage Programmable Output Voltage Range Output Current Output Current Limit VIN–VOUT ∆VOUT Dropout Voltage Line Regulation Load Regulation eN PSRR IGND COUT tSTART-UP Output Noise Voltage Power Supply Ripple Rejection Ratio Ground Current Output Capacitance Output Capacitor ESR Start-Up Time from Shutdown Condition 1 mA ≤ IOUT ≤ 150 mA, VOUT = 2.7V 3.0V ≤ VBATT = VIN ≤ 5.5V 0 µA ≤ IOUT ≤ 150 mA Programming Resolution = 100 mV (VOUT + 0.25V, 3.0V)MAX ≤ VBATT VBATT = VIN ≤ 5.5V VOUT = 0V IOUT = 75 mA (VOUT + 0.25V, 3.0V)MAX ≤ VBATT VBATT = VIN ≤ 5.5V, IOUT = 75 mA VIN = 3.6V, 1 mA ≤ IOUT ≤ 150 mA 10 Hz ≤ f ≤ 100 kHz, COUT = 2.2 µF f = 217 Hz, COUT = 2.2 µF IOUT = 100 µA 0 µA ≤ IOUT ≤ 150 mA COUT = 2.2 µF, IOUT = 150 mA Note 10 2 5 60 500 30 3 10 27 57 30 20 500 41 µVRMS dB µA µF mΩ µs 173 mV mV Min −3 2.5 Typ Max +3 3.2 150 Units % V ± 1.0 3.0 mA 9 www.national.com LP3941A VO8 LDO Electrical Characteristics Unless otherwise noted, VIN = VBATT = 3.6V. Typical values and limits appearing in normal type apply for TJ = 25˚C. Limits appearing in boldface type apply over the entire junction temperature range for operation, −40 to +125˚C. (Notes 2, 8, 9) Symbol VOUT Accuracy VOUT Range IOUT Parameter Output Voltage Programmable Output Voltage Range Output Current Output Current Limit VIN–VOUT ∆VOUT Dropout Voltage Line Regulation Load Regulation eN PSRR IGND COUT tSTART-UP Output Noise Voltage Power Supply Ripple Rejection Ratio Ground Current Output Capacitance Output Capacitor ESR Start-Up Time from Shutdown Condition 1 mA ≤ IOUT ≤ 150 mA, VOUT = 2.7V 3.0V ≤ VBATT = VIN ≤ 5.5V 0 µA ≤ IOUT ≤ 150 mA Programming Resolution = 100 mV (VOUT + 0.25V, 3.0V)MAX ≤ VBATT VBATT = VIN ≤ 5.5V VOUT = 0V IOUT = 75 mA (VOUT + 0.25V, 3.0V)MAX ≤ VBATT VBATT = VIN ≤ 5.5V, IOUT = 75 mA VIN = 3.6V, 1 mA ≤ IOUT ≤ 150 mA 10 Hz ≤ f ≤ 100 kHz, COUT = 2.2 µF f = 217 Hz, COUT = 2.2 µF IOUT = 100 µA 0 µA ≤ IOUT ≤ 150 mA COUT = 2.2 µF, IOUT = 150 mA (Note 10) 2 5 60 510 30 3 12 27 57 30 20 500 41 µVRMS dB µA µF mΩ µs 173 mV mV Min −3 2.5 Typ Max +3 3.2 150 Units % V ± 1.0 3.0 mA VO9 LDO Electrical Characteristics Unless otherwise noted, VIN = VBATT = 3.6V. Typical values and limits appearing in normal type apply for TJ = 25˚C. Limits appearing in boldface type apply over the entire junction temperature range for operation, −40 to +125˚C. (Notes 2, 8, 9) Symbol VOUT Accuracy VOUT Range IOUT Parameter Output Voltage Programmable Output Voltage Range Output Current Output Current Limit VIN–VOUT ∆VOUT Dropout Voltage Line Regulation Load Regulation eN PSRR IGND COUT tSTART-UP Output Noise Voltage Power Supply Ripple Rejection Ratio Ground Current Output Capacitance Output Capacitor ESR Start-Up Time from Shutdown Condition 1 mA ≤ IOUT ≤ 200 mA, VOUT = 2.2V 3.0V ≤ VBATT = VIN ≤ 5.5V 0 µA ≤ IOUT ≤ 200 mA Programming Resolution = 100 mV (VOUT + 0.25V, 3.0V)MAX ≤ VBATT VBATT = VIN ≤ 5.5V VOUT = 0V IOUT = 100 mA (VOUT + 0.25V, 3.0V)MAX ≤ VBATT VBATT = VIN ≤ 5.5V, IOUT = 100 mA VIN = 3.6V, 1 mA ≤ IOUT ≤ 200 mA 10 Hz ≤ f ≤ 100 kHz, COUT = 4.7 µF f = 217 Hz, COUT = 4.7 µF IOUT = 100 µA 1 µA ≤ IOUT ≤ 200 mA COUT = 4.7 µF, IOUT = 200 mA (Note 10) 2 5 60 770 50 3 15 27 60 30 20 500 44 µVRMS dB µA µF mΩ µs 288 mV mV Min −3 1.5 Typ Max +3 3.0 200 Units % V ± 1.0 3.0 mA www.national.com 10 LP3941A VO10 LDO Electrical Characteristics Unless otherwise noted, VIN = VBATT = 3.6V. Typical values and limits appearing in normal type apply for TJ = 25˚C. Limits appearing in boldface type apply over the entire junction temperature range for operation, −40 to +125˚C. (Notes 2, 8, 9) Symbol VOUT Accuracy VOUT Range IOUT Parameter Output Voltage Programmable Output Voltage Range Output Current Output Current Limit VIN–VOUT ∆VOUT Dropout Voltage Line Regulation Load Regulation eN PSRR IGND COUT tSTART-UP Output Noise Voltage Power Supply Ripple Rejection Ratio Ground Current Output Capacitance Output Capacitor ESR Start-Up Time from Shutdown Condition 1 mA ≤ IOUT ≤ 150 mA, VOUT = 2.2V 3.0V ≤ VBATT = VIN ≤ 5.5V 0 µA ≤ IOUT ≤ 150 mA Programming Resolution = 100 mV (VOUT + 0.25V, 3.0V)MAX ≤ VBATT VBATT = VIN ≤ 5.5V VOUT = 0V IOUT = 75 mA (VOUT + 0.25V, 3.0V)MAX ≤ VBATT VBATT = VIN ≤ 5.5V, IOUT = 75 mA VIN = 3.6V, 1 mA ≤ IOUT ≤ 150 mA 10 Hz ≤ f ≤ 100 kHz, COUT = 2.2 µF f = 217 Hz, COUT = 2.2 µF IOUT = 100 µA 0 µA ≤ IOUT ≤ 150 mA COUT = 2.2 µF, IOUT = 150 mA (Note 10) 2 5 60 610 30 3 12 27 57 30 20 500 41 µVRMS dB µA µF mΩ µs 204 mV mV Min −3 1.5 Typ Max +3 3.0 150 Units % V ± 1.0 2.5 mA VO11 LDO Electrical Characteristics Unless otherwise noted, VIN = VBATT = 3.6V. Typical values and limits appearing in normal type apply for TJ = 25˚C. Limits appearing in boldface type apply over the entire junction temperature range for operation, −40 to +125˚C. (Notes 2, 8, 10) Symbol VOUT Accuracy VOUT Range IOUT Parameter Output Voltage Programmable Output Voltage Range Output Current Output Current Limit VIN–VOUT ∆VOUT Dropout Voltage Line Regulation Load Regulation eN PSRR IGND COUT tSTART-UP Output Noise Voltage Power Supply Ripple Rejection Ratio Ground Current Output Capacitance Output Capacitor ESR Start-Up Time from Shutdown Condition 1 mA ≤ IOUT ≤ 200 mA, VOUT = 2.7V 3.0V ≤ VBATT = VIN ≤ 5.5V 0 µA ≤ IOUT ≤ 200 mA Programming Resolution = 100 mV (VOUT + 0.25V, 3.0V)MAX ≤ VBATT VBATT = VIN ≤ 5.5V VOUT = 0V IOUT = 100 mA (VOUT + 0.25V, 3.0V)MAX ≤ VBATT VBATT = VIN ≤ 5.5V, IOUT = 100 mA VIN = 3.6V, 1 mA ≤ IOUT ≤ 200 mA 10 Hz ≤ f ≤ 100 kHz, COUT = 4.7 µF f = 217 Hz, COUT = 4.7 µF IOUT = 100 µA 1 mA ≤ IOUT ≤ 200 mA COUT = 4.7 µF, IOUT = 200 mA (Note 10) 2 5 60 900 50 3 15 27 60 30 20 500 44 µVRMS dB µA µF mΩ µs 302 mV mV Min −2 1.8 Typ Max +5 3.3 200 Units % V ± 2.0 1.8 mA 11 www.national.com LP3941A Unless otherwise noted, 2.5V < VBU_BAT < 3.3V. Typical values and limits appearing in normal type apply for TJ = 25˚C. Limits appearing in boldface type apply over the entire junction temperature range for operation, −40 to +125˚C. (Notes 2, 8, 9) Symbol VOUT Accuracy IQ IOUT VIN–VRTC PSRR COUT Parameter Output Voltage Quiescent Current Output Current Output Current Limit Dropout Voltage Power Supply Ripple Rejection Ratio Output Capacitance Output Capacitor ESR Condition IOUT ≤ 50 µA, VOUT = 1.8V 2.15V ≤ VBU-BAT ≤ 3.3V IOUT = 6 µA 2.15V ≤ VBU-BAT ≤ 3.3V VOUT = 0V IOUT = 50 mA f = 100 Hz, COUT = 1.0 µF 1 mA ≤ IOUT ≤ 200 mA 0.75 5 1000 Min 1.6 Typ 1.8 2.6 10 2000 150 20 1.0 2.2 500 Max 2.0 6 50 10000 190 Units V µA µA mV dB µF mΩ VRTC LDO Electrical Characteristics Note: The RTC_LDO can be disabled via the I2C compatible interface by setting the corresponding disable bit. See Table 1 for further details. Back-Up Charger Electrical Characteristics Unless otherwise noted, VIN = VBATT = 3.6V. Typical values and limits appearing in normal type apply for TJ = 25˚C. Limits appearing in boldface type apply over the entire junction temperature range for operation, −40 to +125˚C. (Notes 2, 8, 9) Symbol VIN VOUT Accuracy IQ IOUT Parameter Operational Voltage Range Output Voltage Quiescent Current Output Current Output Current Limit PSRR Power Supply Ripple Rejection Ratio Output Capacitance Output Capacitor ESR IOUT ≤ 50 µA, VOUT = 3.15V VOUT + 0.4 ≤ VBATT ≤ 5.5V IOUT < 50 µA VOUT + 0.4 ≤ VBATT = VIN ≤ 5.5V, VOUT = 3.0V 3.2V ≤ VBATT = VIN ≤ 5.5V VOUT = 0V IOUT ≤ 50 µA, VOUT = 3.15V VOUT + 0.4 ≤ VBATT = VIN ≤ 5.5V f < 10 kHz 0 µA ≤ IOUT ≤ 100 µA 5 0.7 Condition Min Typ VOUT + 0.4 3.0 3.15 25 70 1.5 150 2 Max 5.5 3.3 Units V V µA µA mA 15 0.1 500 dB µF mΩ COUT Note: The back-up battery charger can be disabled by setting the corresponding enable bit ‘0’ via the I2C interface. See Table 1 for further details. Comparators’ Electrical Characteristics Unless otherwise noted, VBATT = +2.5V to 5.5V, VO3 = 3.0V, VCM = 0.27V. Typical values and limits appearing in normal type apply for TJ = 25˚C. Limits appearing in boldface type apply over the entire junction temperature range for operation, −40 to +125˚C. (Notes 2, 8, 9) Symbol VT IB IOS PSRR VOL VOH tPLH tPHL tLH tHL Parameter Comparator Trip Voltage Input Bias Current Input Offset Current Power Supply Rejection Ratio Output Voltage Low Output Voltage High Propagation Delay Low to High Propagation Delay High to Low Rise Time Low to High Fall Time High to Low 2.7V ≤ VBATT ≤ 5.5V ISINK = 1 mA ISOURCE = 1 mA Overdrive = 100 mV (Note 10) Overdrive = 100 mV (Note 10) Overdrive = 100 mV COUT = 10 pF (Note 10) Overdrive = 100 mV COUT = 10 pF (Note 10) 2.57 VINV = 1.3V Condition Min 230 Typ 270 0.01 1 50 0.24 VO3–0.25 5 5 5 5 0.37 3 Max 300 0.15 Units mV µA nA dB V V µs µs ns ns www.national.com 12 LP3941A Comparators’ Electrical Characteristics (Continued) Unless otherwise noted, VBATT = +2.5V to 5.5V, VO3 = 3.0V, VCM = 0.27V. Typical values and limits appearing in normal type apply for TJ = 25˚C. Limits appearing in boldface type apply over the entire junction temperature range for operation, −40 to +125˚C. (Notes 2, 8, 9) Parameter Quiescent Current per Comparator Condition Min Typ 5 Max Units µA Symbol IQ Note: Comparator output buffers are powered by LDO3 output voltage. RESET Electrical Characteristics Unless otherwise noted, VBATT = +2.5V to 5.5V. Typical values and limits appearing in normal type apply for TJ = 25˚C. Limits appearing in boldface type apply over the entire junction temperature range for operation, −40 to +125˚C. (Notes 2, 8, 9) Symbol VOH VOL VTSHLD tDELAY tPS-HOLD Parameter Output Voltage High Output Voltage Low VO1 Threshold RESET Active Time-Out Period PS-HOLD Timer Condition Internal Logic Supply ISOURCE = 0 µA Internal Logic Supply ISINK = 500 µA VO1 Rising VO1 Falling From VO1 ≥ 93% until RESET = High From RESET = Hi to PS-HOLD = Hi From PS-HOLD = Low to RESET = Low From RESET = Low until LDOs turned off (no output regulation) 90 82 34 29 93 85 40 35 Min VO3–0.2 0.4 96 88 47 41 Typ Max Units V V % % ms ms tRESET RPU IS-MAX Shut-Down Timer Pull-up Resistance to VO1 Maximum Sink Current 51 60 14 70 ms kΩ 5 mA LED Driver Electrical Characteristics Unless otherwise noted, VBATT = +2.5V to 5.5V. Typical values and limits appearing in normal type apply for TJ = 25˚C. Limits appearing in boldface type apply over the entire junction temperature range for operation, −40 to +125˚C. (Notes 2, 8, 9) Symbol VOL ILEAKAGE Parameter LED1–3 Output Low Level LED1–3 Off Leakage Current VDR = 5.5V Condition ISINK = 40 mA Min Typ 0.17 4 Max 0.55 Units V µA Main Battery Charger Electrical Characteristics Unless otherwise noted, VCHG-IN = 5V, VBATT = 4V. Typical values and limits appearing in normal type apply for TJ = 25˚C. Limits appearing in boldface type apply over the entire junction temperature range for operation, −40 to +125˚C. (Notes 2, 9, 8, 12) Symbol VCHG-IN VOK−TSHD VUVLO−TSHD Parameter Input Voltage Range Operating Range Adapter OK Trip Point (CHG-IN) Under Voltage Lock-Out Trip Point Battery Connected VCHG-IN–VBATT Rising VCHG-IN–VBATT Falling VCHG-IN Rising VCHG-IN Falling VCHG-IN Rising VCHG-IN Falling VBATT = 4.2V VCHG-IN ≤ 4V Charging Complete, charger connected, VBATT = 4.1V 5.46 3.85 Condition Min 4.5 4.5 80 30 4.25 3.90 6.00 5.80 8 2 150 6.54 4.65 Typ Max 12 6 Units V mV mV V V V V µA µA µA VOVLO−TSHD Over Voltage Lock-Out Trip Point IBATTSENSE IBATT Leakage Current Battery Input Current 13 www.national.com LP3941A Main Battery Charger Electrical Characteristics (Continued) Unless otherwise noted, VCHG-IN = 5V, VBATT = 4V. Typical values and limits appearing in normal type apply for TJ = 25˚C. Limits appearing in boldface type apply over the entire junction temperature range for operation, −40 to +125˚C. (Notes 2, 9, 8, 12) Parameter Fast Charge Current Accuracy Fast Charge Current Range Programmable Charging Current Step Condition ICHG = 700 mA Min −10 478 43 VBATT = 2V 28 42 120 1.2 59 Typ Max +10 937 Units % mA mA mA mΩ A Symbol ICHG ±5 IPRE−CHG RSENSE Pre-Charge Current Internal Current Sense Resistance Internal Current Sense Resistor Load Current CHARGING PERFORMANCE VBATT Battery Regulation Voltage (CV Mode, for 4.1V Cell) Battery Regulation Voltage CV mode, for 4.2V Cell) VCHG-Q VBAT-RST Full Charge Qualification Threshold Restart Threshold Voltage (For 4.1V Cell) Restart Threshold Voltage (For 4.2 Cell) tEOC Time to EOC State Resolution INL DNL Relative Accuracy Differential Nonlinearity No Missing Code −1 −1 A/D CONVERTER PERFORMANCE 8 +1 +1 Bits LSB LSB TA −40˚C to +85˚C TA −40˚C to +85˚C VBATT Rising, Transition from Pre-Charge to Full Current VBATT Falling, Transition from EOC, to Pre-Qual State VBATT Falling, Transition from EOC, to Pre-Qual State −40˚C to +85˚C (Note 10) 4.80 4.015 4.115 2.8 4.1 4.2 3.0 3.9 V 4.0 5.625 6.55 Hrs 4.19 4.289 3.2 V Note: While charging a Li-Ion battery with this charger is possible in cold temperatures (generally below −5˚C–0˚C) is possible with the LP3941A, charging a battery outside its manufacturer recommended temperature limits is strongly discouraged. I2C Compatible Interface Electrical Characteristics Unless otherwise noted, VBATT = +2.5V to 5.5V. Typical values and limits appearing in normal type apply for TJ = 25˚C. Limits appearing in boldface type apply over the entire junction temperature range for operation, −40 to +125˚C. (Notes 2, 8, 9) Symbol FCLK tBF tHOLD tCLK-LP tCLK-HP tSU tDATA-HOLD tDATA-SU tSU tTRANS Parameter Clock Frequency Bus-Free Time between START and STOP Hold Time Repeated START Condition CLK Low Period CLK High Period Set-Up Time Repeated START Condition Data Hold Time Data Set-Up Time Set-Up Time for STOP Condition Maximum Pulse Width of Spikes that must be suppressed by the input filter of both DATA & CLK signals. (Note 10) (Note 10) (Note 10) (Note 10) (Note 10) (Note 10) (Note 10) (Note 10) (Note 10) 50 ns 1.3 0.6 1.3 0.6 0.6 0 100 0.6 Condition Min Typ Max 400 Units kHz µs µs µs µs µs µs ns µs Note 1: Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which operation of the device is guaranteed. Operating Ratings do not imply guaranteed performance limits. For guaranteed performance limits and associated test conditions, see the Electrical Characteristics tables. Note 2: All voltages are with respect to the potential at the GND pin. Note 3: The amount of Absolute Maximum power dissipation allowed for the device depends on the ambient temperature and can be calculated using the formula www.national.com 14 LP3941A I2C Compatible Interface Electrical Characteristics P = (TJ – TA)/θJA, (Continued) (1) where TJ is the junction temperature, TA is the ambient temperature, and θJA is the junction-to-ambient thermal resistance. Junction-to-ambient thermal resistance is highly application and board-layout dependent. In applications where high maximum power dissipation exists, special care must be paid to thermal dissipation issues in board design. Internal thermal shutdown circuitry protects the device from permanent damage. Thermal shutdown engages at TJ = 150oC (typ.) and disengages at TJ = 140oC (typ.). Note 4: For detailed soldering specifications and information, please refer to National Semiconductor Application Note 1187: Leadless Leadframe Package (LLP) (AN-1187). Note 5: The Human body model is a 100 pF capacitor discharged through a 1.5 kΩ resistor into each pin. (MIL-STD-883 3015.7) The machine model is a 200 pF capacitor discharged directly into each pin. (EAIJ) Note 6: In applications where high power dissipation and/or poor package thermal resistance is present, the maximum ambient temperature may have to be derated. Maximum ambient temperature (TA-MAX) is dependent on the maximum operating junction temperature (TJ-MAX-OP = 125˚C), the maximum power dissipation of the device in the application (PD-MAX), and the junction-to ambient thermal resistance of the part/package in the application (θJA), as given by the following equation: TA-MAX = TJ-MAX-OP − (θJA x PD-MAX). Note 7: Junction-to-ambient thermal resistance (θJA) is taken from a thermal modeling result, performed under the conditions and guidelines set forth in the JEDEC standard JESD51–7. The test board is a 4-layer FR-4 board measuring 102 mm x 76 mm x 1.6 mm with a 2x1 array of thermal vias. The ground plane on the board is 50 mm x 50 mm. Thickness of copper layers are 36 µm/1.8 µm/18 µm/36 µm (1.5 oz/1 oz/1 oz/1.5 oz). Ambient temperature in simulation is 22˚C, still air. Power dissipation is 1W. Junction-to-ambient thermal resistance is highly application and board-layout dependent. In applications where high maximum power dissipation exists, special care must be paid to thermal dissipation issues in board design. The value of θJA of this product can vary significantly, depending on PCB material, layout, and environmental conditions. In applications where high maximum power dissipation exists (high VIN, high IOUT), special care must be paid to thermal dissipation issues. For more information on these topics, please refer to Application Note 1187: Leadless Leadframe Package (LLP) and the Power Efficiency and Power Dissipation section of this datasheet. Note 8: All limits are guaranteed by design, test and/or statistical analysis. All electrical characteristics having room-temperature limits are tested during production with TJ = 25˚C. All hot and cold limits are guaranteed by correlating the electrical characteristics to process and temperature variations and applying statistical process control. Note 9: Capacitors: Low-ESR Surface-Mount Ceramic Capacitors are (MLCCs) used in setting electrical characteristics. Note 10: Guaranteed by design. Note 11: Dropout voltage is the input-to-output voltage difference at which the output voltage is 100 mV below its nominal value. This specification does not apply in cases it implies operation with an input voltage below the 3.0V minimum appearing under Operating Ratings. For example, this specification does not apply for devices having 1.5V outputs because the specification would imply operation with an input voltage at or about 1.5V. Note 12: LP3941A is not intended as a Li-Ion battery protection device. Battery used in this application should have an adequate internal protection. 15 www.national.com LP3941A LP3941A Simplified Block Diagram 20094504 www.national.com 16 LP3941A Typical Performance Characteristics noted, TA = 25˚C, VBATT = 3.6V, VBU_BATT = 3.15V. 200 mA LDO Output Voltage Under nominal conditions. This means, unless otherwise 200 mA LDO PSRR 20094506 20094509 150 mA LDO Output Voltage 150 mA LDO PSRR 20094505 20094508 50 mA LDO Output Voltage 50 mA LDO PSRR 20094507 20094510 17 www.national.com LP3941A Typical Performance Characteristics Under nominal conditions. This means, unless otherwise noted, TA = 25˚C, VBATT = 3.6V, VBU_BATT = 3.15V. (Continued) Pre-Charge Current Fast Charging Current 20094516 20094515 Charging Termination Voltage Back-Up Battery Full Voltage 20094514 20094513 Back-Up Battery Charging Current RTC-LDO Output Voltage 20094512 20094511 www.national.com 18 LP3941A LP3941A Serial Port Communication Address Code TABLE 1. LP3941 Control and Data Codes Addr 8h'00 8h'01 Register Enable LDO9/ LDO1 Data Code LDO10/ LDO2 Data Code LDO8/ LDO3 Data Code LDO11/ LDO4 Data Code LDO5 Data Code LDO6 Data Code LDO7 Data Code Charger Register –1 Charger Register –2 7 LDO7–EN (0) LDO9 Code 3 (1) LDO10 Code 3 (1) Not Used (0) LDO11 Code 3 (0) Not Used (0) Not Used (0) Not Used (0) Not Used (0) Not Used (0) 6 LDO6–EN (0) LDO9 Code 2 (1) LDO10 Code 2 (0) LDO8 Code 2 (1) LDO11 Code 2 (0) Not Used (0) Not Used (0) Not Used (0) Not Used (0) Not Used (0) 5 LDO5–EN (1) LDO9 Code 1 (1) LDO10 Code 1 (1) LDO8 Code 1 (0) LDO11 Code 1 (0) Not Used (0) Not Used (0) Not Used (0) Not Used (0) Not Used (0) 4 LDO4–EN (0) LDO9 Code 0 (1) LDO10 Code 0 (0) LDO8 Code 0 (1) LDO11 Code 0 (0) Not Used (0) Not Used (0) Not Used (0) 4.1V/4.2V (1) EOC R/O 3 LDO3–EN (1) LDO1 Code 3 (0) LDO2 Code 3 (1) Not Used (0) LDO4 Code 3 (1) Not Used (0) Not Used (0) Not Used (0) Charger Current Code 3 (0) Charging R/O 7h’7E Numbers in parentheses indicate default setting: (0) bit is set to low state, and (1) bit is set to high state. R/O –Read Only, All other bits are Read and Write. 2 LDO2–EN (0) LDO1 Code 2 (0) LDO2 Code 2 (1) LDO3 Code 2 (1) LDO4 Code 2 (1) LDO5 Code 2 (0) LDO6 Code 2 (0) LDO7 Code 2 (1) Charger Current Code 2 (0) EOC Sel-1 (0) 1 LDO1–EN (1) LDO1 Code 1 (1) LDO2 Code 1 (0) LDO3 Code 1 (0) LDO4 Code 1 (1) LDO5 Code 1 (1) LDO6 Code 1 (1) LDO7 Code 1 (0) Charger Current Code 1 (0) EOC Sel-0 (1) 0 LDO8–EN (0) LDO1 Code 0 (1) LDO2 Code 0 (1) LDO3 Code 0 (1) LDO4 Code 0 (1) LDO5 Code 0 (1) LDO6 Code 0 (1) LDO7 Code 0 (1) Charger Current Code 0 (1) ChargerDIS Off/On (0) LED3 Enable (0) 8h'02 8h'03 8h'04 8h'05 8h'06 8h'07 8h'08 8h'09 8h'0a Control/ Enable LDO9-EN (0) LDO10-EN (0) LDO11-EN (0) Back-Up Battery Charger Enable (1) Not Used (0) ADC4 R/O R/O (0) RTC Alarm R/O RTC_LDO Disable (0) LED1 Enable (0) LED2 Enable (0) 8h'0b ADC Control Register ADC Output Register Power-OnReason Register ADC/ Status Register Not Used (0) ADC7 R/O R/O (0) COMP2 OUT R/O Not Used (0) ADC6 R/O R/O (0) COMP1 OUT R/O Not Used (0) ADC5 R/O R/O (0) ON R/O ADC Start (0) ADC3 R/O ON R/O Charger Present R/O ADC EN (0) ADC2 R/O RTC ALARM R/O HF_PWR R/O ADC Mux-1 (1) ADC1 R/O CHG_IN R/O ADC Overflow R/O ADC Mux-0 (1) ADC0 R/O HF_PWR R/O ADC Data Ready R/O 8h'0c 8h'0d 8h'2e Note 13: Registers h’0c, h’0d, h’2e and h’09 bits 3 and 4 are read only (R/O). 19 www.national.com LP3941A LP3941A Serial Port Communication Address Code 7h’7E (Continued) TABLE 1. LP3941 Control and Data Codes (Continued) Note 14: Register h’0d stores the status of ON, RTC_ALARM, CHG_IN and HF_PWR inputs at the time of PMIC power on event. The bits indicate why the device turned on, and are static after the power on incident. ON = 1 means the ON-input was logic high at the moment of power-up-sequence start. RTC_ALARM = 1 indicates that RTC_ALARM-input was logic high when the power-up-sequence started. CHG_IN = 1 indicates that external battery charger initiated the power-up-sequence. This also implies that the battery is connected (BSNS = 0V) and that battery voltage is over 3.0V, because otherwise the circuit will not power up. HF_POWER = 1 indicates HF_PWR was logic high when the power-up-sequence started. 0 in any register bit position means that the corresponding signal did not initiate the power-up sequence. Multiple bits can be ‘1’ at the same time if they simultaneously initiated the power-up-sequence. Note 15: Register h’2e shows the current status of comparator outputs, ADC block, ON-, RTC_ALARM and HF_PWR-inputs. Bit 3 of the register indicates if a valid external battery charger is connected to the LP3941 at the moment. Register h’2e is dynamic and shows the current status of these variables at all times. COMP1/2 OUT = 1 means the corresponding comparator input is > threshold (see comparator specification). ON, RTC_ALARM, HF_PWR = 1 indicates corresponding input pins are logic high. CHARGER_PRESENT means CHG_IN pin has valid voltage for charging. (See charger specification.) Note 16: For description on the operation of ADC Overflow and ADC Data Ready bits please see ADC specifications. Regulator Output Voltage Programming The following table summarizes the supported output voltages for LP3941A. Default voltages after start-up sequence have been highlighted in bold. Data Code 4h'00 4h'01 4h'02 4h'03 4h'04 4h'05 4h'06 4h'07 4h'08 4h'09 4h'0a 4h'0b 4h'0c 4h'0d 4h'0e 4h'0f VO1 (V) 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 VO2 (V) 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 VO3 (V) 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 VO4 (V) 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 VO5 (V) 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 VO6 (V) 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 VO7 (V) 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 VO8 (V) 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 VO9 (V) 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 VO10 (V) 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 VO11 (V) 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 Register Programming Examples Example 1. Setting register h’00 value to 8h’ff’ will enable LDOs 1–8. Example 2. Setting register h’01 to 8h’8c’ will set LDO9 output to 2.3V and LDO1 output to 2.7V. These voltages will appear at the LDO outputs if the corresponding LDOs have been enabled. Programming a voltage value to a LDO, which is off, will affect the LDO output voltage after the LDO is enabled. Enabling and programming the output voltage are separate operations. Example 3. Setting register h’09 bit ‘0’ to ‘1’ will disable the main battery charger. Note that all register bits have to be programmed together. It is not possible to program individual bits alone. Writing into read only or unused bit positions does not affect those bits nor does it cause errors. Therefore to disable the main charger and to retain other bits in their default values on would write 8h‘03’ ADC and Charger Programming The following tables show how to select the main battery charger End-Of-Charge current limit, how to set the charger current limit and select a particular input for ADC measurement. Default values have been highlighted in bold. EOC Current Selection Code SEL-1 0 1 1 SEL-0 1 0 1 ISET (mA) 0.1C 0.15C 0.2C A/D Input Selection Code MUX-1 0 0 1 MUX-0 0 1 0 VBATT ICHG BATT-ID (20 µA Scale) Input www.national.com 20 LP3941A ADC and Charger Programming (Continued) A/D Input Selection Code MUX-1 1 MUX-0 1 Input BATT-ID (200 µA Scale) A/D Converter’s Charge Current Output Code ADC Control Register Code 2h’0X Device Temperature +85˚C ICHARGE (mA) Output Code 0 h’00 3.27 h’01 … 831 h’fe 834 h’ff Charger Current Selection Code Data Code 4h’01 4h’02 4h’03 4h’04 4h’05 4h’06 4h’07 4h’08 4h’09 ISET (mA) 530 574 617 660 703 746 789 832 874 The next table shows the relationship between ADC output code and main battery voltage in ADC Battery Voltage Measurement Mode. A/D Converter’s Battery Voltage Output Code ADC Control Register Code 2h’0X Battery Voltage (V) Output Code 3.000 h’00 3.006 h’01 … 4.494 h’fe 4.500 h’ff The battery ID resistor value can be determined using the following table in the two ADC Battery ID Modes. Battery ID Detection Code ADC Control Register Code 2h’0X ID Resistor (kΩ) Scale 1 (200 µA) Scale 1 (20 µA) Data Code Range Data Code Range 0.22 0.75 1.8 3.3 5.1 10 15 22 33 55 h’00–h’12 h’13–h’32 h’33–h’65 h’66–h’a7 h’a8–h’ff h’1e–h’31 h’32–h’49 h’4a–h’6d h’6e–h’b0 h’b1–h’ff The following table is the conversion table for main battery charger current measurement using the on-chip ADC. Temperature dependency is due to the temperature coefficient of the aluminum sense resistor. The ADC itself is temperature compensated as is the charging current in the main battery charger. A/D Converter’s Charge Current Output Code ADC Control Register Code 2h’0X Device Temperature −40˚C ICHARGE (mA) Output Code ICHARGE (mA) Output Code 0 h’00 0 h’00 4.97 h’01 3.95 h’01 … … 1262 h’fe 1003 h’fe 1267 h’ff 1007 h’ff Device Temperature +25˚C ADC Block Functional Diagram The ADC block provides four different functions on the LP3941A: • Main battery voltage measurement • Main battery charger charging current measurement • Battery ID resistor resistance measurement with 200 µA sense current • Battery ID resistor resistance measurement with 20 µA sense current The following picture shows the implementation of these measurements with the ADC. 21 www.national.com LP3941A ADC Block Functional Diagram (Continued) 20094518 I2C Read and Write Sequences 20094528 Format to address LP3941A registers 20094519 Combined read and write format. www.national.com 22 LP3941A Li-Ion Battery Charger Operation 20094520 Charging Profile Note 17: (*) Battery charging termination voltage level, charging current and End-of-Charging current level are programmable. Battery charging termination voltage can be 4.1V or 4.2V (default). Maintenance charging start limit is 200 mV below the termination voltage level. End-of-Charging current level can be 20%, 15% or 10% (default) of maximum charging current. Picture shows typical situation with default programming. See LP3941A register map for programming details. 23 www.national.com LP3941A Li-Ion Battery Charger State Diagram 20094521 www.national.com 24 LP3941A LP3941A Power-Up/Down Sequences 20094523 Power-up initiated by the ON-signal. 25 www.national.com LP3941A LP3941A Power-Up/Down Sequences (Continued) 20094522 Power-up initiated by hands free signal, RTC Alarm or charger insertion. Note 18: If LDO1 does not reach 93% of nominal output level in 60 ms, LP3941A powers down. Note 19: If PS_HOLD does not go high in 35 ms from RESET high, LP3941A powers down. Note 20: If UVLO occurs before the rising edge of the PS_HOLD, LP3941A powers down. Note 21: If LDO1 output drops below 85% of nominal output level, LP3941A waits for 90 ms for it to recover to 93% (with RESET = ‘0’) before powering down. If LDO1 output reaches 93%, power-up sequence resumes with 40 ms RESET delay. Note 22: LP3941A powers down after PS_HOLD has been low for > 35 ms continuously. ON-signal, HF_PWR, CHG_IN or RTC ALARM have no control over shutdown operation, but it has to be initiated using PS_HOLD. Power-Up/Down Reason and Status Register Operation Register h’0d stores the reason (the activating signal) for powering up the PMU. The possible inputs that can activate the LP3941 are the ON, HF_PWR, RTC ALARM and CHG_IN signals. The signal that activated the LP3941A will have its corresponding bit set to ‘1’. If multiple signals activate the PMU simultaneously then they are all marked with ‘1’ in register h’0d. Register h’2e maintains the current status of ON, HF_PWR and RTC_ALARM signals and indicates the presence of an external charger connected to the PMU. This register shows the current status of the inputs whereas h’0d indicates the reason for power-up and remains thereafter static until another power-up sequence occurs. Register h’2e also indicates the status of the two comparator outputs and the status of the ADC as well. Note that the bit indicating the presence of an external charger voltage in register h’2e differs provides different information than that in register h’0d. Register h’0d CHG_INbit is ‘1’ if CHG_IN-pin was logic high at start-up. Register h’2e Charger Present-bit indicates whether the CHG_IN pin voltage is within acceptable limits (4.5V ≤ VCHG_IN ≤ 6.0V) for charging. If the VCHG_IN is valid for charging then this bit in register h’2e is set to ‘1’. Flowchart Operation The power-up/power-down state machine is reset when VBATT pin is less than 2.1V. The state machine is reset into the POWEROFF state. In this state the UVLO in enabled. All other functions except the RTC_LDO are off. If an external charger or hands free power is connected, the state machine advances to the EXTERNAL STANDBY state and waits for the battery voltage to reach 3.0V. When the battery voltage reaches 3.0V the state machine advances to the TURNON LDOs state. In the EXTERNAL STANDBY state UVLO is enabled. If the battery voltage reaches 3.0V before hands free power or a charger is connected the state machine advances to the STANDBY state. The back-up battery charger is enabled. If the ON-key is pressed, a charger is inserted, hands free power is connected or the RTC_ALARM goes high the state machine advances to the TURNON LDOs state. Once in the TURNON LDOs state LDOs 1, 3 and 5 are enabled. The state machine remains in this state until LDO1 output reaches 93% of its nominal value or 60 ms have 26 www.national.com LP3941A Flowchart Operation (Continued) passed. If LDO1 reaches 93%, the state machine advances to the RESET OFF DELAY state. If 60 ms have passed before the 93% level is achieved, the state machine returns to the STANDBY state and waits for another wakeup source. The RESET OFF DELAY state counts off 40 ms. If the battery voltage drops below the UVLO threshold of 2.5V, the state machine goes to the ENABLE RESET state and power down sequence. If LDO1 output drops below 85% of the nominal voltage the state machine returns to the TURNON LDOs state in an attempt to restart the LDO. If neither of these conditions occurs the state machine advances to the PS_HOLD DETECT state. In the PS_HOLD DETECT, RESET is deasserted and the state machine waits 35 ms for the PS_HOLD signal to go high. If PS_HOLD goes high within 35 ms of RESET going low the state machine advances to the IDLE state. If PS_HOLD in still low after 35 ms the state machine goes to ENABLE RESET state and the power down sequence. If battery voltage pins drops below the UVLO threshold, the state machine advances to the ENABLE RESET state and the power down sequence. If LDO1 output drops below its 85% point the state machine returns to the TURNON LDOs state in an attempt to try restart the LDOs. The state machine remains in the IDLE state until PS_HOLD goes low for 35 ms. If PS_HOLD is low for less than 35 ms the state machine remains in the IDLE state. If PS_HOLD stays low for more than 35 ms, the state machine advances to the ENABLE RESET state and the power down sequence. If LDO1 output falls below its 85% point the state machine returns to the TURNON LDOs state in an attempt to restart the LDOs. The UVLO is disabled in the IDLE state. The back-up battery charger is on. In the ENABLE RESET state RESET is asserted. After 60 ms all LDOs are turned off. UVLO as well as the back-up battery charger are on. Once LDO1 falls to its 85% point the state machine returns to the STANDBY state. The RTC_LDO is powered by the back-up battery and is always on (unless specifically disabled via the I2C interface). 27 www.national.com LP3941A LP3941A Power-Up/Power-Down Flowchart 20094524 www.national.com 28 LP3941A Detailed PU/PD Flowchart 20094525 29 www.national.com LP3941A Detailed PU/PD Flowchart (Continued) 20094526 www.national.com 30 LP3941A Detailed PU/PD Flowchart (Continued) 20094527 31 www.national.com LP3941A Cellular Phone Power Management Unit Physical Dimensions inches (millimeters) unless otherwise noted 48–Pin Leadless Leadframe Package NS Package Number LQA48B LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. BANNED SUBSTANCE COMPLIANCE National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.