PC87200160A

PC87200 PCI to ISA Bridge August 1999 PC87200 PCI to ISA Bridge 1.0 General Description The PC87200 Enhanced Integrated PCI-to-ISA bridge works with an LPC chipset to provide ISA slot support. It is a complement to the National Semiconductor PC8736x Super I/O family. 2.2 PCI-to-ISA Bridge – PCI 2.1 compliant 33 MHz bus – Supports PCI initiator-to-ISA and ISA master-to-PCI cycle translations – Subtractive agent for unclaimed transactions (see the PROHIBIT signal description for exceptions) – Parallel to Serial IRQ conversion including IRQ3,4,5,6,7,9,10,11,12,14,15 – Supports 4 ISA slots directly without buffering – Programmable ISA clock (8.33 to 11 MHz) – Slow slew rate on edges 2.0 Features 2.1 General – Functionally compatible with Intel 82380AB – 5.0 V tolerant PCI and ISA interfaces – Slave mode serialized IRQ support for both quiet and continuous modes – PC/PCI DMA support – 32-bit address decode for the 1MB BIOS ROM – Supports ISA bus mastering – 160-pin PQFP package 2.3 "PROHIBIT" functional support – Disables PCI bus subtractive decoding when PROHIBIT is asserted Block Diagram PCI Bus Serialized IRQ Interface PCI to X-Bus / X-Bus to PCI Bridge PC87200 Support PCI Configuration Registers Decoding logic X-Bus Arbiter PROHIBIT BPD# X-Bus PCPCIREQ# Serial IRQ Slave mode interface logic ISA bus Target Interface ISA bus Master Interface PC/PCI DMA Interface PCPCIGNT# ISA Bus TRI-STATE® is a registered trademark of National Semiconductor Corporation. © 1999 National Semiconductor Corporation www.national.com Table of Contents 1.0 2.0 General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.2 PCI-to-ISA Bridge . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.3 "PROHIBIT" functional support . . . . . . . . . . . . . . . 1 Device Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3.1 PCI Bus Interface . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3.2 ISA Bus Interface . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3.3 Serialized IRQ support . . . . . . . . . . . . . . . . . . . . . . 3 3.4 PROHIBIT signal support . . . . . . . . . . . . . . . . . . . 5 3.5 PC/PCI DMA Interface Support . . . . . . . . . . . . . . . 5 Device Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 5.1 Signal Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . 8 5.2 Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . 9 5.3 Signal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . 9 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . 16 7.1 Register Summary . . . . . . . . . . . . . . . . . . . . . . . . 16 7.2 Chipset Register Space . . . . . . . . . . . . . . . . . . . . 17 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . 22 8.1 Electrical Specifications . . . . . . . . . . . . . . . . . . . . 22 8.2 PC87200Test Modes . . . . . . . . . . . . . . . . . . . . . . 22 8.3 Electrical Connections . . . . . . . . . . . . . . . . . . . . . 29 8.4 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . 29 8.5 Recommended Operating Conditions . . . . . . . . . 29 8.6 DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . 30 8.7 AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 31 Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . 33 3.0 4.0 5.0 6.0 7.0 8.0 9.0 2 www.national.com 3.0 Device Overview The PC87200 can be described as providing the functional ter devices, and a PC/PCI DMA master for DMA transfer cycles. The PC87200 supports positive decode for the blocks shown in Figure 1. BIOS ROM in the special test mode and implements sub— PCI bus master/slave interface tractive decode for unclaimed PCI accesses when the — ISA bus master/slave interface PROHIBIT signal is low. The PC87200 also generates address and data parity and performs parity checking. — Serial IRQ slave mode interface — PROHIBIT signal support Configuration registers are accessed through the PCI interface using the PCI Bus Type 1 configuration mechanism as — PC/PCI DMA interface described in the PCI 2.1 Specification. 3.1 PCI Bus Interface The PC87200 provides a PCI bus interface that is both a slave for PCI cycles initiated by the CPU or other PCI masPCI Bus Serialized IRQ Interface PCI to X-Bus / X-Bus to PCI Bridge PC87200 Support PCI Configuration Registers Decoding logic X-Bus Arbiter PROHIBIT BPD# X-Bus PCPCIREQ# Serial IRQ Slave mode interface logic ISA bus Target Interface ISA bus Master Interface PC/PCI DMA Interface PCPCIGNT# ISA Bus Internal Block Diagram 3.2 ISA Bus Interface ized IRQ defined in the Serialized IRQ on the “PCI way” Version 6.0 specification. Programming of the serial interThe PC87200 provides an ISA bus interface for subtracrupt controller when the controller is currently running can tive-decoded memory and I/O cycles on PCI. The produce unexpected results. PC87200 is the default subtractive decoding agent and will forward all unclaimed memory and I/O cycles to the ISA interface; however, the PC87200 may be configured to ignore either I/O, memory or all unclaimed cycles (subtractive decode disabled) by asserting the PROHIBIT signal. ISA master cycles will only be passed to the PCI bus if they access memory. I/O accesses are left to complete on the ISA bus. ISA master cycles that access memory on ISA bus are not supported by the PC87200. 3.3 Serialized IRQ support The PC87200’s Serial Interrupt interface uses a serial interrupt bus to transmit ISA Bus legacy interrupt requests. The bus is a one pin bus (SERIRQ) and uses the PCI clock as its timing reference. The serial interrupt bus is a multidrop bus that is shared by all PCI devices that have legacy interrupts. The serial interrupt logic conforms to the serial- 3 www.national.com 3.0 Device Overview (Continued) Timing of the serialized IRQ is illustrated as follows. START CYCLE START PCI CLK SERIRQ Driving Source Slave (Q) Master (C) START Master NONE NONE IRQ1 Source R T S IRQ0 R T S IRQ1 R R = Recovery; T= Turn-around; S = Sample Start Cycle Timing IRQ15 S PCI CLK SERIRQ Driving Source IRQ15 Source NONE R T S IOCHK# R T STOP CYCLE STOP(NOTE 1) R T START NONE Master NONE R = Recovery; T= Turn-around; S = Sample NOTE 1: The Stop pulse is 2 clocks wide for Quiet mode, 3 clocks wide for Continuous mode Stop Cycle Timing 3.3.1 Serial Interrupts (Slave Mode) There are two types of Serial Interrupt transfer modes; the following describes the operation of the PC87200’s Serial Interrupt Interface as a Slave: 1. Quiet Mode: Any Serial Interrupt device may initiate a Start Cycle, while the Serial Interrupt interface is Idle, by driving SERIRQ low for one PCI clock period. After driving low for one clock the device should immediately TRISTATE® SERIRQ, without ever driving this signal high. A Start Cycle may not be initiated in the middle of an active Serial Interrupt transfer. Between Stop and Start Cycles the SERIRQ signal will be pulled high and the Serial Interrupt interface will be Idle. When the PC87200 Serial Interrupt interface must initiate a Start Cycle in order to transfer any pending interrupt request to the Master. The only exception to this requirement is when a Serial Interrupt transfer sequence is already in progress and the PC87200 can transfer the request during this present Serial Interrupt transfer sequence, then the Serial Interrupt device is not required to generate another Start Cycle. 2. Continuous Mode: The PC87200 tracks both the Start and Stop Frames and is responsible for inserting its interrupt requests on the appropriate IRQ frames. 3.3.2 IRQ Sampling Periods IRQ Sample Period is three clocks long, with the first clock being the Sampled phase, the second clock being the Recovery phase, and the third clock being the Turn-around phase. During the Sample phase the Serial Interrupt device drives SERIRQ low if its associated IRQ signal/data is presently low. If its IRQ signal/data is high the Serial Interrupt device must TRI-STATE SERIRQ. During the Recovery phase, the Serial Interrupt device that drove SERIRQ low (if any Serial Interface device does) is required to drive back high. During the Turn-around phase all Serial Interface devices will TRI-STATE SERIRQ. All Serial Interface devices will drive SERIRQ low at the appropriate sample point regardless of which device initiated the sample activity, if its associated IRQ signal/data is low. Slave The PC87200 will support the interrupt request frames listed in the following table. The Generation clock for each IRQ follows the low to high edge of the Start Pulse by the number of PCI Clocks listed in Table 1. Note: : The number of clocks equals: (3 x (IRQ number + 1)) - 1 3.3.3 Stop Cycle Control The PC87200 will monitor SERIRQ for a Stop Cycle, so that it may initiate a Start Cycle for a pending transition in Once a Start Cycle has been initiated all Serial Interrupt any of its IRQs (Quiet Mode). For Continuous Mode, the devices watch for the rising edge of the Start Pulse and PC87200 will not initiate any Start Cycle, but will track the start counting IRQ Sample periods from that point. Each Start and Stop Cycles and insert its IRQs appropriately. 4 www.national.com 3.0 Device Overview (Continued) Table 1. SERIRQ Slave Generation Periods SERIRQ Period 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 21:18 Signal Generated Reserved. Reserved. Reserved. IRQ3 IRQ4 IRQ5 IRQ6 IRQ7 Reserved. IRQ9 IRQ10 IRQ11 IRQ12 Reserved. IRQ14 IRQ15 IOCHK# Reserved. # of clocks past Start 2 5 8 11 14 17 20 23 26 29 32 35 38 41 44 47 50 62,59,56, 53 3.4 PROHIBIT signal support The chipset will use this signal to claim the BIOS first and then deassert the "PROHIBIT" signal to configure the PCI to ISA bridge to continue the boot sequence. Special test mode support is provided by means of the BPD# pin. When this test mode is active, the PC87200 will enable positive memory decode during boot up to enable the host to look for boot ROM on ISA card. PROHIBIT will be a don’t care in this test mode at boot up for the ROM BIOS range, but should function normally after booting 3.5 PC/PCI DMA Interface Support The PC87200 operates as a PC/PCI DMA Secondary Arbitration Bridge. The PC87200 can pass all seven legacy ISA bus DMA channel requests to the PC/PCI DMA Primary Bus Arbiter using the channel passing protocol defined in the Moble PC/PCI DMA Arbitration and Protocol Specification (Revision 2.2). Figure 1 shows the topology of the PC87200 PC/PCI DMA requests and grants: The PC87200 converts the seven legacy ISA bus DMA requests (DREQ0, 1, 2, 3, 5, 6 and 7) into a serial PC/PCI DMA compliant REQ# sequence and converts the corresponding PC/PCI DMA GNT# sequence into the appropriate DMA acknowledge (DACK0-3, 5-7#). This PC/PCI DMA expansion Channel Passing Protocol is illustrated Figure 2. PC/PCI DMA Primary Bus Arbiter PCI Bus PCPCIGNT# PCPCIREQ# PC87200 PC/PCI DMA Interface Support DACK6# DREQ6 DACK2# DREQ2 DACK0# DREQ0 DACK1# DREQ1 DACK3# DREQ3 DACK5# DREQ5 DACK7# DREQ7 ISA Bus Figure 1. PC87200 PC/PCI DMA Topology PCICLK PCPCIREQ# PCPCIGNT# start CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7 start bit 0 bit 1 bit 2 Figure 2. Channel Passing Protocol 5 www.national.com 3.0 Device Overview (Continued) When a legacy ISA bus DMA request is asserted, the PC87200 will transmit that request to the PC/PCI Primary Bus Arbiter by encoding it and driving it out the PC87200’s PCPCIREQ# according to the above; first PCPCIREQ# will be driven low for one PCICLK period to indicate that the serial encoded request transfer is starting. Then the PC87200 will drive each of the next eight bits with the value of its corresponding DREQ. (NOTE: Channel 4 will always be driven low.) At the end of the request sequence, the PC87200 will continue to drive its PCPCIREQ# signal active, indicating that the request is still being maintained. In response to the request sequence, the PC/PCI Primary Bus Arbiter will respond with a PC/PCI DMA encoded grant transfer when it is granting the PCI bus for a PC/PCI DMA transfer cycle. The PC/PCI encoded grant transfer will begin when the PC/PCI Primary Bus Arbiter drives PCPCIGNT# low for one PCICLK period to indicate the start of the grant sequence; then the next three PCPCIGNT# signal PCICLK periods will then contain the encoded grant value, indicating which legacy ISA DMA channel is being granted the PC Bus. bit 2 0 0 0 0 1 1 1 1 bit 1 0 0 1 1 0 0 1 1 bit 0 0 1 0 1 0 1 0 1 Channel Granted DMA Channel 0 (DACK0#) DMA Channel 0 (DACK1#) DMA Channel 0 (DACK2#) DMA Channel 0 (DACK3#) RESERVED DMA Channel 0 (DACK5#) DMA Channel 0 (DACK6#) DMA Channel 0 (DACK7#) 3.5.4 Clock Generation The PC87200 generates the ISA clock using PCI clock signal (typically 33 MHz). A PCICLK divisor (3,4) is programmable through PCI configuration register to generate the ISA clock signal. This provides support for the generation of ISACLK frequencies 8.33 MHz and 11 MHz off of a 33MHz PCICLK. Figure 3. shows a block diagram for clock generation within the PC87200. PC87200 PCICLK N SYSCLK Figure 3. PC87200 Clock Generation After receiving a valid grant from the PC/PCI DMA Arbiter, the PC87200 will recognize the following I/O accesses as DMA I/O Reads(Writes) from (to) the granted legacy ISA DMA channel. DMA Cycle Type Normal Normal TC Verify Verify TC DMA TC (A2) PCI Cycle Type I/O Address 0000_0000h 0000_0004h 0000_00C0h 0000_00C4h 0 1 0 1 I/O Read/Write I/O Read/Write I/O Read I/O Read. PCI bus address bit 2 (A2) indicates if the cycle is to be a Terminal Count cycle or not. For Normal DMA Cycles, PCI bus I/O Reads and Writes will be translated to legacy ISA DMA Reads and Writes respectively. For Verify DMA Cycles, only PCI bus I/O Reads will be translated to legacy ISA DMA Verify cycles. 6 www.national.com 4.0 Device Pinout Vdd Vss SA18 SA19 IRQ9 DACK2# DREQ2 SYSCLK SD7 SD6 SD5 SD4 IOCHK# REFRESH# SD3 SD2 SD1 SD0 Vdd Vss IOCHRDY SMEMR# AEN SMEMW# IOR# IOW# BALE MEMCS16# IOCS16# SA20 SA21 SA22 SA23 IRQ10 IRQ11 IRQ12 IRQ15 IRQ14 Vdd Vss 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 7 DACK0# DREQ0 MEMR# MEMW# DACK5# DREQ5 SD8 SD9 SD10 SD11 DACK6# DREQ6 SD12 SD13 SD14 SD15 DACK7# DREQ7 Vdd Vss MASTER# SBHE# TC BPD# AD31 AD30 AD29 AD28 AD27 AD26 Vdd Vss AD25 AD24 C/BE3# IDSEL AD23 AD22 Vdd Vss 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 AD0 AD1 AD2 AD3 AD4 AD5 Vss Vdd AD6 AD7 C/BE0# AD8 AD9 AD10 Vss Vdd AD11 AD12 AD13 AD14 AD15 C/BE1# Vss Vdd PAR SERR# STOP# DEVSEL# TRDY# IRDY# Vss Vdd FRAME# C/BE2# AD16 AD17 AD18 AD19 AD20 AD21 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 160 159 158 157 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 SA17 SA16 SA15 SA14 SA13 SA12 SA11 SA10 SA9 Vss Vdd SA8 SA7 SA6 SA5 SA4 SA3 SA2 SA1 SA0 Vss Vdd PROHIBIT DREQ1 DACK1# RSTDRV DREQ3 DACK3# IRQ7 IRQ6 IRQ5 IRQ4 IRQ3 SERIRQ PCPCIGNT# PCPCIREQ# PCIRST# PCICLK Vss Vdd www.national.com 5.0 Pin Descriptions 5.1 Signal Definitions This section defines the signals and describes the external interface of the PC87200. The following diagram shows the pins organized by their functional groupings. Internal test and electrical pins are not shown. Serialized SERIRQ IRQ Interface PCICLK SYSCLK Clocks AD[31:0] C/BE[3:0]# IDSEL PC87200 PCIRST# RSTDRV Reset Enhanced Integrated PCI-to-ISA Bridge SA[23:0] SD[15:0] IOCHK# SBHE# BALE IOCHRDY REFRESH# IOCS16# IOR# IOW# MEMCS16# MEMR# MEMW# AEN IRQ[15:14], [12:9], [7:3] MASTER# DREQ[7:5], [3:0] DACK#[7:5], [3:0] TC SMEMW# SMEMR# PCI Bus FRAME# IRDY# TRDY# STOP# DEVSEL# PAR SERR# ISA Bus PCPCIREQ# PCPCIGNT# PROHIBIT BPD# PC87200 Signal Groups 8 www.national.com 5.0 Pin Descriptions (Continued) 5.2 Pin Assignments The tables in this section use several common abbreviations. Table 2. lists the mnemonics and their meanings. In the next section, description of each signal within its associated functional group is provided. Table 2. Pin Type Definitions Mnemonic I I/O O OD PU PD smt s/t/s Standard input pin. Bidirectional pin. Totem-pole output. Open-drain output structure that allows multiple devices to share the pin in a wired-OR configuration. Pull-up resistor. Pull-down resistor. Schmitt Trigger. Sustained TRI-STATE, an active-low TRI-STATE signal owned and driven by one and only one agent at a time. The agent that drives an s/t/s pin low must drive it high for at least one clock before letting it float. A new agent cannot start driving an s/t/s signal any sooner than one clock after the previous owner lets it float. A pull-up resistor is required to sustain the inactive state until another agent drives it and must be provided by the central resource. TRI-STATE signal. Definition t/s VDD (PWR) Power pin. VSS (GND) Ground pin. # The "#" symbol at the end of a signal name indicates that the active, or asserted state occurs when the signal is at a low voltage level. When "#" is not present after the signal name, the signal is asserted when at a high voltage level. 5.3 Signal Descriptions 5.3.1 Reset Signals Signal Name PCIRST# RSTDRV Pin No. 124 135 Type I O PCI Reset PCIRST# is the reset signal for the PCI bus. Reset Drive This signal is asserted to reset devices that reside on the ISA bus. It will be driven by the inverse of the PCIRST# input signal. 5.3.2 Clock Interface Signals Signal Name PCICLK Pin No. 123 Type I PCI Clock This clock runs at the PCI clock frequency and is used to drive most of the PC87200 circuitry. SYSCLK 8 O ISA Bus Clock ISACLK is derived from PCICLK and is typically programmed for 8.33MHz. F0 Index 50h[2:0] is used to program the ISA clock divisor. These bits determine the divisor of the PCI clock used to generate the ISA bus clock. If F0 Index 50h[2:0] is set to: 010 = Divide by three (sysclk=11MHz) 011 = Divide by four (sysclk = 8.33MHz) All other values are invalid and can produce unexpected results. Description Description 9 www.national.com 5.0 Pin Descriptions (Continued) 5.3.3 PCI Interface Signals Signal Name AD[31:0] Pin No. 65,66, 67,68, 69,70, 73,74, 77,78, 81,82, 83,84, 85,86, 100,101, 102,103, 104,107, 108,109, 111,112, 115,116, 117,118, 119,120 75,87, 99,110 Type I/O t/s PCI Address/Data AD[31:0] is a physical address during the first clock of a PCI transaction; it is the data during subsequent clocks. When the PC87200 is a PCI master, AD[31:0] are outputs during the address and write data phases, and are inputs during the read data phase of a transaction. When the PC87200 is a PCI slave, AD[31:0] are inputs during the address and write data phases, and are outputs during the read data phase of a transaction. Description C/BE[3:0]# I/O t/s PCI Bus Command and Byte Enables During the address phase of a PCI transaction, C/BE[3:0]# defines the bus command. During the data phase of a transaction, C/BE[3:0]# are the data byte enables. C/BE[3:0]# are outputs when the PC87200 is a PCI master and are inputs when it is a PCI slave. IDSEL FRAME# 76 88 I I/O t/s Initialization Device Select It is used as a chip select during configuration read and write transactions. PCI Cycle Frame FRAME# is asserted to indicate the start and duration of a transaction. It is deasserted on the final data phase. FRAME# is an input when the PC87200 is a PCI slave. PCI Initiator Ready IRDY# is driven by the master to indicate valid data on a write transaction, or that it is ready to receive data on a read transaction. When the PC87200 is a PCI slave, IRDY# is an input that can delay the beginning of a write transaction or the completion of a read transaction. Wait cycles are inserted until both IRDY# and TRDY# are asserted together. IRDY# 91 I/O t/s TRDY# 92 I/O t/s PCI Target Ready TRDY# is asserted by a PCI slave to indicate it is ready to complete the current data transfer. TRDY# is an input that indicates a PCI slave has driven valid data on a read or a PCI slave is ready to accept data from the PC87200 on a write. TRDY# is an output that indicates the PC87200 has placed valid data on AD[31:0] during a read or is ready to accept the data from a PCI master on a write. Wait cycles are inserted until both IRDY# and TRDY# are asserted together. STOP# 94 I/O t/s PCI Stop As an input, STOP# indicates that a PCI slave wants to terminate the current transfer. The transfer will be aborted, retried, or disconnected. As an output, STOP# is asserted with TRDY# to indicate a target disconnect, or without TRDY# to indicate a target retry. 10 www.national.com 5.0 Pin Descriptions (Continued) Signal Name DEVSEL# Pin No. 93 Type I/O t/s PCI Device Select DEVSEL# is asserted by a PCI slave, to indicate to a PCI master and subtractive decoder that it is the target of the current transaction. As an input, DEVSEL# indicates a PCI slave has responded to the current address. As an output, DEVSEL# is asserted one cycle after the assertion of FRAME# and remains asserted to the end of a transaction as the result of a positive decode. DEVSEL# is asserted four cycles after the assertion of FRAME# if the PC87200 is selected as the result of a subtractive decode. The subtractive decode sample point can be configured in F0 Index 41h[2:1]. These cycles are passed to the ISA bus. PAR 96 I/O t/s PCI Parity PAR is the parity signal driven to maintain even parity across AD[31:0] and C/BE[3:0]#. The PC87200 drives PAR one clock after the address phase and one clock after each completed data phase of write transactions as a PCI master. It also drives PAR one clock after each completed data phase of read transactions as a PCI slave. SERR# 95 O OD PCI System Error SERR# is pulsed by a PCI device to indicate an address parity error. Description 11 www.national.com 5.0 Pin Descriptions (Continued) 5.3.4 ISA Bus Interface Signals Signal Name MASTER# Pin No. 61 Type I ISA Master Mode: Master The MASTER# input asserted indicates an ISA bus master is driving the ISA bus and that it may access any device on the system board. SA[23:0] 33,32, 31,30, 4,3,160, 159,158, 157,156, 155,154, 153,152, 149,148, 147,146, 145,144, 143,142, 141 56,55, 54,53, 50,49, 48,47, 9,10, 11,12, 15,16, 17,18 24 I/O System Address Bus This bus carries the addresses for all ISA cycles. Description SD[15:0] I/O System Data Bus This bus carries the data for all ISA cycles. SMEMW# O System Memory Write SMEMW# is output on this pin. SMEMW# is asserted for any memory write accesses below 1MB. It enables 8-bit memory slaves to decode the memory address on SA[19:0]. SMEMR# 22 O System Memory Read SMEMR# is output on this pin. SMEMR# is asserted for memory read accesses below 1MB. It enables 8-bit memory slaves to decode the memory address on SA[19:0]. SBHE# 62 I/O System Bus High Enable The PC87200 or ISA master asserts SBHE# to indicate that SD[15:8] will be used to transfer a byte at an odd address. SBHE# is an output during non-ISA master DMA operations. It is driven as the inversion of AD0 during 8-bit DMA cycles. It is forced low for all 16-bit DMA cycles. SBHE# is an input during ISA master operations. BALE 27 I/O Buffered Address Latch Enable/Special Test mode BALE indicates when SA[23:0] and SBHE# are valid and may be latched. This pin will be used as strap for special test mode with the PROHIBIT signal by checking its input level during reset. IOCHRDY 21 I/O OD I/O Channel Ready IOCHRDY deasserted indicates that an ISA slave requires additional wait states. When the PC87200 is an ISA slave, IOCHRDY is an output indicating additional wait states are required. REFRESH# 14 I/O OD Refresh Cycle indicator The PC87200 supports the standard ISA refresh function. When the ISA bus is not in use by the ISA bus controller, the DMA controller, or an ISA bus master, the refresh control logic will generate an ISA refresh cycle. The 87200 also supports refresh requests initiated by ISA masters. 12 www.national.com 5.0 Pin Descriptions (Continued) Signal Name IOCS16# Pin No. 29 Type I I/O Chip Select 16 IOCS16# is asserted by 16-bit ISA I/O devices based on an asynchronous decode of SA[15:0] to indicate that SD[15:0] may be used to transfer data (8-bit ISA I/O devices use SD[7:0]). IOR# IOW# MEMCS16# 25 26 28 I/O I/O I/O OD I/O Read IOR# is asserted to request an ISA I/O slave to drive data onto the data bus. I/O Write IOW# is asserted to request an ISA I/O slave to accept data from the data bus. Memory Chip Select 16 MEMCS# is asserted by 16-bit ISA memory devices based on an asynchronous decode of SA[23:17] to indicate that SD[15:0] may be used to transfer data (8bit ISA memory devices use SD[7:0]). Memory Read MEMR# is asserted for all memory read accesses (including those above 1MB). It enables 16-bit memory slaves to decode the memory address on SA[23:0]. MEMW# 44 I/O Memory Write MEMW# is asserted for all memory write accesses (including those above 1MB). It enables 16-bit memory slaves to decode the memory address on SA[23:0]. AEN 23 O Address Enable AEN asserted indicates to ISA memory devices that a valid address for a DMA transfer is present on SA[23:0], and for I/O devices to ignore this address and any data on the ISA bus. IRQ[15:14], [12:9], [7:3] 37,38, 36,35, 34,5, 132,131, 130,129, 128 58 52, 46,134, 7,137,42 57,51, 45,133, 6,136,41 63 13 I ISA Bus Interrupt Request IRQ inputs are interrupts that indicate ISA devices or other devices requesting a CPU interrupt service. Description MEMR# 43 I/O DREQ[7:5], DREQ[3:0] DACK[7:5]#, DACK[3:0]# TC IOCHK# I DMA Request - Channels [7:5], [3:0] DREQ inputs are asserted by ISA DMA devices to request a DMA transfer. The request must remain asserted until the corresponding DACK# is asserted. O DMA Acknowledge- Channels [7:5], [3:0] DACK# outputs are asserted to indicate when a DREQ is granted and the start of a DMA cycle. O I Terminal Count TC signals the final data transfer of a DMA transfer. I/O channel check Asserted by an ISA device indicating an error condition. 5.3.5 Miscellaneous Signals (Continued) Signal Name SERIRQ PROHIBIT Pin No. 127 138 Type I/O s/t/s I Serial IRQ This is a one pin bus that conveys interrupt source information to the chipset. PROHIBIT An active high signal from the chipset indicating that the PC87200 should not act as the subtractive decode agent on the PCI bus. BPD# 64 I BIOS Positive Decode (active low) When this pin is asserted low after BALE is detected high after reset, the PROHIBIT signal will be a don’t care. The BIOS memory range will be positively decoded and claimed as such. All other cycles are still subtractively decoded. Description 13 www.national.com 5.0 Pin Descriptions (Continued) 5.3.6 PC/PCI signals PCPCIREQ# 125 O PC/PCI Bus Request The PC87200 asserts PCPCIREQ# using the PC/PCI DMA request protocol in response to a DMA request or ISA master request to gain ownership of the PCI bus. The PCPCIREQ# and PCPCIGNT# signals are used to arbitrate for the PCI bus. PCPCIGNT# 126 I PC/PCI Bus Grant PCPCIGNT# is asserted using the PC/PCI DMA grant protocol by an arbiter that indicates to the PC87200 that access to the PCI bus has been granted. 5.3.7 Power, Ground, and Reserved Terminals Signal Name VDD Pin No. 1,19,39, 59,71, 79,89, 97,105, 113,121, 139,150 2,20,40, 60,72, 80,90, 98,106, 114,122, 140,151 Type PWR Description 3.3V (nominal) Power Connection VSS GND Ground Connection 14 www.national.com 6.0 Configuration a. Connect the NOGO signal of the south bridge to Prohibit cards with option ROM (e.g.,VGA cards, SCSI cards) to pin of PC87200, SERIRQ to SERIRQ, REQ[A] to work properly. PCPCIREQ#, GNT[A] to PCPCIGNT# (other PC/PCI REQ, GNT pair may also be used). If BPD# is not being used, it should be pulled high. b. On power-up reset (i.e., cold boot), the NOGO signal is high on reset and therefore disables the subtractive decoding capability of PC87200. The rationale for doing this is as follows: on the PCI bus, only one subtractive decoding agent can exist. Since the south bridge will normally power up as the subtractive decoding agent, the PC87200 must be “prohibited” from doing so. Any other GPO pin which is high on reset can also be used. c. After PCI bus enumeration, when the device ID and vendor ID of PC87200 is found, do the following: d. Enable serial IRQ in continuous mode, 21 frames and 4 clock start frame by setting register 64h of south bridge to d0h. (In the old south bridge, the serial IRQ pin is multiplexed with a GPIO and need to be selected as serial IRQ. In the latest industry standard south bridge, however, the serial IRQ is a dedicated pin and does not require initialization.) e. Enable PC/PCI DMA by setting the PC/PCI request and grant pins to PC/PCI DMA mode, instead of using them as GPIOs. Any PC/PCI request and grant pair can be used, but on the south bridge, GNT[B] is multiplexed with GNT[5], so PC/PCI request and grant pair A is more preferable to use. Set all channels of DMA to PC/PCI DMA except for channels 4 & 2 (channel 4 is for cascading the DMAC and channel 2 is for FDC). The value to be put in register 91:90 is 5475 for the latest south bridge and 5455 for older south bridges. The difference is due to the use of “11” for LPC DMA, and the value of 00 (ISA DMA) being put into reserved instead. f. Enable positive decode for the devices under the new south bridge: program the value of 3C0F into reg. E7:E6 will enable positive decode for most devices except sound and gameport. Changing it to enable/disable other devices will be straightforward for the new south bridge. (For old south bridges, it will be harder, and requires one to find all the bits to set/reset. ) g. Enable the new south bridge to do positive decode by setting bit 1 of reg. B0h to 1. h. Set the NOGO signal to low. i. Program register 42h of PC87200 to 20h. This is a required initialization step. j. Program a value of 03 into register D3h of device 1Fh in function 0 of the new south bridge. This will prevent the PC87200 from responding to configuration accesses afterwards. The rationale for doing this is to prevent Windows from detecting two ISA bridges, the other one being the PCI-to-LPC bridge, and thus creating a conflict. NOTE that you must connect AD22 to IDSEL of PC87200 for this to work. After this, proceed in normal BIOS flow. Note that step d to j must be performed before ISA bus enumeration, and therefore before ISA plug and play initialization and option ROM checking. This is needed for plug and play cards and 15 www.national.com 7.0 Register Descriptions The 87200 is a single function device. Its register space is The remaining subsections of this chapter is as follows: called the Bridge Configuration Registers Space (F0) — A brief discussion on how to access the registers located which is accessed through the PCI interface using the PCI in the PCI Configuration Space. Type One Configuration Mechanism. — Register summary. The PCI header is a 256-byte region used for configuring a PCI device or function. The first 64 bytes are the same for — Detailed bit formats of all registers. all PCI devices and are predefined by the PCI specification. 7.1 Register Summary These registers are used to configure the PCI for the The tables in this subsection summarize all the registers of device. The rest of the 256-byte region is used to configure the PC87200. Included in the tables are the register’s reset the device or function itself. values. Table 3. Function 0: Bridge Configuration Registers Summary F0 Index 00h-01h 02h-03h 04h-05h 06h-07h 08h 09h-0Bh 0Ch 0Dh 0Eh 0Fh 10h-3Fh 40h 41h 42h 43h 44h 45h-4Fh 50h 51h 52h 53h-5Ah 5Bh 5Ch-FFh Width (Bits) 16 16 16 16 8 24 8 8 8 8 -8 8 8 8 8 -8 8 8 -8 -Type RO RO R/W R/W RO RO R/W R/W RO RO -R/W R/W R/W R/W R/W -R/W R/W R/W -R/W -Name Vendor Identification Register Device Identification Register PCI Command Register PCI Status Register Device Revision ID Register PCI Class Code Register PCI Cache Line Size Register PCI Latency Timer Register PCI Header Type Register PCI BIST Register Reserved PCI Function Control Register 1 PCI Function Control Register 2 PCI Function Control Register 3 PCI Function Control Register 4 Reset Control Register Internal use, do not overwrite ISA CLK Divider ISA I/O Recovery Control Register ROM/AT Logic Control Register Internal use, do not overwrite Decode Control Register 2 Internal use, do not overwrite Reset Value 100Bh 0021h 0107h 0280h 00h 060100h 00h 00h 00h 00h 00h 79h 10h 28h 46h 00h -43h 43h 04h -00h -- 16 www.national.com 7.0 Register Descriptions (Continued) 7.2 Chipset Register Space unique to the PC87200. All registers in Function 0 are directly accessed (i.e., there are no memory or I/O mapped The Chipset Register Space of the PC87200 is comprised registers in F0). Table 4 gives the bit formats for these regof one function with PCI header registers. There is no isters. memory or I/O mapped register. IMPORTANT: Register bits marked internal use should 7.2.1 Bridge Configuration Registers - Function 0 not be overwritten, else error will occur. The register space designated as Function 0 (F0) contains registers used to configure features and functionality Table 4. Bridge Configuration Registers Bit Index 00h-01h Index 02h-03h Index 04h-05h 15:10 9 8 7 6 5 4 3 2 1 Reserved — Set to 0. Fast Back-to-Back Enable (Read Only) — This function is not supported when PC87200 is a master. It is always disabled (must always be set to 0). SERR# — Allow SERR# assertion on detection of special errors: 0 = Disable; 1 = Enable. Wait Cycle Control (Read Only) — This function is not supported in PC87200. It is always disabled (bit is set to 0). Parity Error — Allow PC87200 to check for parity errors on PCI cycles for which it is a target, and to assert PERR# when a parity error is detected: 0 = Disable; 1 = Enable. VGA Palette Snoop Enable (Read Only) — This function is not supported in PC87200. It is always disabled (bit is set to 0). Memory Write and Invalidate —Allow PC87200 to do memory write and invalidate cycles, if the PCI Description Vendor Identification Register (RO) Device Identification Register (RO) PCI Command Register (R/W) Reset Value = 100Bh Reset Value =0021h Reset Value = 0107h cache line register is set to 16 bytes (04h). 0=Disable, 1=Enable. Special Cycles — This function is not supported. It must always be set to 0. Bus Master — Allow PC87200 bus mastering capabilities: 0 = Disable; 1 = Enable. Set this bit to 1. Memory Space — Allow PC87200 to respond to memory cycles from the PCI bus: 0 = Disable; 1 = Enable. PC87200 will only respond to memory cycles destined for the ISA bus as none of its internal functions are memory-mapped. 0 I/O Space — Allow PC87200 to respond to I/O cycles from the PCI bus: 0 = Disable; 1 = Enable. PCI Status Register (R/W) Reset Value = 0280h Index 06h-07h 15 14 13 Detected Parity Error — This bit is set whenever a parity error is detected. Write 1 to clear. Signaled System Error — This bit is set whenever PC87200 asserts SERR# active. Write 1 to clear. Received Master Abort — This bit is set whenever a master abort cycle occurs. A master abort will occur when a PCI cycle is not claimed, except for special cycles. Write 1 to clear. Register is cleared after RMA is read. Received Target Abort — This bit is set whenever a target abort is received while the PC87200 is the master for the PCI cycle. Write 1 to clear. Signaled Target Abort — This bit is set whenever the PC87200 signals a target abort. This occurs when an address parity error occurs for an address that hits in the active address decode space of the PC87200. Write 1 to clear. DEVSEL# Timing — These bits are always 01, as the PC87200 will always respond to cycles for which it is an active target with medium DEVSEL# timing. 00 = Fast 01 = Medium 10 = Slow 11 = Reserved 12 11 10:9 17 www.national.com 7.0 Register Descriptions (Continued) Table 4. Bridge Configuration Registers (Continued) Bit 8 Description Data Parity Detected —This bit is set when: 1) The PC87200 asserted PERR# or observed PERR# asserted. 2) PC87200 is the master for the cycle in which the PERR# occurred, and PE is set (F0 Index 04h[6] = 1). Write 1 to clear. 7 6:0 Index 08h Index 09h-0Bh Index 0Ch 7:0 Index 0Dh 7:4 3:0 Reserved — Set to 0. PCI Latency Timer Value — The PCI Latency Timer Register prevents system lockup when a slave does not respond to a cycle that the PC87200 masters. If the value is set to 00h (default), the timer is disabled. If the timer is written with any other value, bits [3:0] become the four most significant bytes in a timer that counts PCI clocks for slave response. The timer is reset on each valid data transfer. If the counter expires before the next assertion of TRDY# is received, the PC87200 stops the transaction with a master abort and asserts SERR#, if enabled to do so. PCI Header Type (RO) Reset Value =00h Fast Back-to-Back Capable — As a target, PC87200 is capable of accepting fast back-to-back transactions: 0 = Disable; 1 = Enable. This bit is always set to 1. Reserved — Set to 0. Device Revision ID Register (RO) PCI Class Code Register (RO) PCI Cache Line Size Register (R/W) PCI Cache Line Size Register — reserved. PCI Latency Timer Register (R/W) Reset Value = 00h Reset Value = 00h Reset Value = 060100h Reset Value = 00h Index 0Eh 7:0 PCI Header Type Register — This.register defines the format of this header. This header is of type format 0. Additionally, bit 7 defines whether this PCI device is a multifunction device (bit 7 = 1) or not (bit 7 = 0). PCI BIST Register (RO) Reserved. Set to 0. Reserved PCI Function Control Register 1 (R/W) Internal use, do not overwrite. Single Write Mode — PC87200 accepts only single cycle write transfers as a slave on the PCI bus and performs a target disconnect with the first data transferred: 0 = Disable (accepts burst write cycles); 1 = Enable. Single Read Mode — PC87200 accepts only single cycle read transfers as a slave on the PCI bus and performs a target disconnect with the first data transferred. 0 = Disable (accepts burst read cycles); 1 = Enable. Retry PCI Cycles — Retry inbound PCI cycles if data is buffered and waiting to go outbound on PCI: 0 = No Retry; 1 = Retry. Write Buffer — PCI slave write buffer: 0 = Disable; 1 = Enable. Reserved- set to 0. BS8/16 — This bit can not be written. Always = 1. Reset Value = 00h Reset Value = 79h Reset Value = 00h Index 0Fh 7:0 Index 10h-3Fh Index 40h 7 6 5 4 3 2:1 0 Note: Bits 6 and 5 emulate the behavior of first generation devices developed for PCI. 18 www.national.com 7.0 Register Descriptions (Continued) Table 4. Bridge Configuration Registers (Continued) Bit Index 41h 7 6 5 Description PCI Function Control Register 2 (R/W) Internal use, do not overwrite PERR# Signals SERR# — Assert SERR# any time that PERR# is asserted or detected active by the PC87200 (allows PERR# assertion to be cascaded to NMI (SMI) generation in the system): 0 = Disable; 1 = Enable. Write Buffer Enable — Allow 16-byte buffering for X-Bus to PCI bus writes: 0 = Disable; 1 = Enable. Internal use, do not overwrite. Subtractive Decode — These bits determine the point at which the PC87200 accepts cycles that are not claimed by another device. The PC87200 defaults to taking subtractive decode cycles in the default cycle clock, but can be moved up to the Slow Decode cycle point if all other PCI devices decode in the fast or medium clocks. Disabling subtractive decode must be done with care, as all ISA and ROM cycles are decoded subtractively. 00 = Default sample (4th clock from FRAME# active) 01 = Slow sample (3rd clock from FRAME# active) 1x = No subtractive decode 0 Index 42h 7 6 5 4 3 2 1 0 Index 43h 7 6 5 4 3 2 1 Reserved — Set to 0. Internal use, do not overwrite. Internal use, do not overwrite. Internal use, do not overwrite. Internal use, do not overwrite. Internal use, do not overwrite. PCI Retry Cycles — When PC87200 is a PCI target and the PCI buffer is not empty, allow PCI bus to retry cycles: 0 = Disable; 1 = Enable. This bit works in conjunction with PCI bus delayed transactions bit. F0 Index 42h[5] must = 1 for this bit to be valid. 0 Index 44h 7 Internal use, do not overwrite. Reset Control Register (R/W) Internal use, do not overwrite. Reset Value = 00000000b Internal use, do not overwrite. PCI Function Control Register 3 (R/W) Internal use, do not overwrite Internal use, do not overwrite. Delayed Transactions — Allow delayed transactions on the PCI bus: 0 = Disable; 1 = Enable. Internal use, do not overwrite. No X-Bus ARB, Buffer Enable — When PC87200 is a PCI target, allow buffer PCI transactions without X-Bus arbitration: 0 = Disable; 1 = Enable. Internal use, do not overwrite. Internal use, do not overwrite. Internal use, do not overwrite. PCI Function Control Register 4 Reset Value = 46h Reset Value = 28h Reset Value = 10h Burst to Beat — Bursts are converted to single beats for X-Bus to PCI bus reads: 0 = Disable; 1 = Enable. 4 3 2:1 19 www.national.com 7.0 Register Descriptions (Continued) Table 4. Bridge Configuration Registers (Continued) Bit 6 5 4 3 2 1 0 Internal use, do not overwrite. Internal use, do not overwrite. Internal use, do not overwrite. Internal use, do not overwrite. Internal use, do not overwrite. Internal use, do not overwrite. X-Bus Warm Start Write only: 0 = NOP; 1 = Execute system wide reset (used only for clock configuration at power-up) Index 45h-4Fh Index 50h 7 6 5 4 3 2:0 Internal use, do not overwrite. Internal use, do not overwrite. Internal use, do not overwrite. Internal use, do not overwrite. Internal use, do not overwrite. ISA Clock Divisor — Determines the divisor of the PCI clock used to generate the ISA bus clock: 010 = Divide by three (ISA clock = 11MHz) 011 = Divide by four (ISA clock = 8.33 MHz) All other values are invalid and can produce unexpected results. Index 51h 7:4 ISA I/O Recovery Control Register (R/W) Reset Value = 43h Internal use, do not overwrite ISA CLK Divider (R/W) Reset Value = 43h Description 8-Bit I/O Recovery — These bits determine the number of ISA bus clocks between back-to-back 8-bit I/O read cycles. This count is in addition to a preset one-clock delay built into the controller. 0000 = 1 PCI clock1101 = 14 PCI clocks 0001 = 2 PCI clocks1110 = 15 PCI clocks :::1111 = 16 PCI clocks 3:0 16-Bit I/O Recovery — These bits determine the number of ISA bus clocks between back-to-back 16-bit I/O cycles. This count is in addition to a preset one-clock delay built into the controller. 0000 = 1 PCI clock1101 = 14 PCI clocks 0001 = 2 PCI clocks1110 = 15 PCI clocks :::1111 = 16 PCI clocks Index 52h 7 6 5 4 3 2 1 0 Internal use, do not overwrite. Internal use, do not overwrite. Internal use, do not overwrite. Internal use, do not overwrite. Internal use, do not overwrite. ROM Control Register (R/W) Reset Value = 04h ROM 1MB Enable — Allow addressing to 512K or 1MB ROM (FFF00000h-FFFFFFFFh): 0 = Disable; 1 = Enable. Internal use, do not overwrite. Internal use, do not overwrite. 20 www.national.com 7.0 Register Descriptions (Continued) Table 4. Bridge Configuration Registers (Continued) Bit Index 53h-5Ah Index 5Bh 7 6 5 Reserved — Set to 0. BIOS ROM Positive Decode — Selects positive or subtractive decoding for accesses to the configured ROM space: 0 = Subtractive; 1 = Positive. Internal use, do not overwrite. Internal use, do not overwrite. Internal use, do not overwrite. Internal use, do not overwrite. Internal use, do not overwrite. Description Internal use, do not overwrite Decode Control Register 2 (R/W) Internal use, do not overwrite. Reset Value = 00h 4 3 2 1 0 Note: Positive decoding by the PC87200 speeds up the I/O cycle time. Index 5Ch-FFh Internal use, do not overwrite 21 www.national.com 8.0 Electrical Characteristics 8.1 Electrical Specifications This section provides information on testing modes, electrical connections, absolute maximum ratings, recommended operating conditions, and DC/AC characteristics. All voltage values in Electrical Specifications are with respect to VSS unless otherwise noted. For detailed information on the PCI bus electrical specification refer to Chapter 4 of the PCI Bus Specification, Revision 2.1. 8.2 PC87200 Test Modes The PC87200 can be forced into different test modes. The following table summarizes the test mode selection process. Table 5. Test mode selection Mode PCIRST# Reserved NAND tree test Reserved Reserved Reserved Reserved SCAN_MODE = 1, SCAN_ENABLE = 0, SCAN_MODE = 1, SCAN_ENABLE = 1, X-BUS_DISABLE = 1 Note: x = Don’t Care Signal Name BALE during reset 0 0 0 0 0 0 0 0 IRQ3 IRQ4 IRQ5 IRQ6 IRQ7 0 x 1 1 1 0 1 1 1 x 0 1 1 0 0 0 0 x 0 0 1 0 0 1 0 x 0 0 0 1 1 1 1 0 1 1 1 1 1 1 x x x x x x x x 22 www.national.com 8.0 Electrical Characteristics (Continued) 8.2.1 Test Mode Logic This block will produce various test mode signals for different test modes : — NAND test signal — XBus test signal — Test mode signal — Scan mode signal 0 test_in pad_bale_in 1 pad_pcirstx_in x_clk irq3 irq4 irq6 irq7 test_in scan_mode irq3 irq4 irq5 irq6 test_in xbus_test irq3 irq4 irq5 irq6 test_in pad_pcirstx_in test_mode Test signal generation logic 23 www.national.com 8.0 Electrical Characteristics (Continued) DRV is the final output. BALE, PCIRSTX and IRQ7 are not included in the NAND chain because they are required to During NAND tree testing, all outputs and bi-directional put the chip to NAND test mode. The NAND tree connecpins will be tri-stated except BALE and RSTDRV pins. The tion is as shown below. first input of the NAND chain is SA18. The NAND chain is routed counter-clockwise around the chip (eg. SA18, SA19, IRQ9, ...). TC is the intermediate output and RST8.2.2 NAND Tree Connections SA18 SA19 xdma_tc SBHEX 0 TC 1 nand_test_en BPDX ~pad_pcirstx_in SA16 0 RSTDRV SA17 1 nand_test_en test_in irq7 nand_test_en NAND Tree Diagram 24 www.national.com 8.0 Electrical Characteristics (Continued) 8.2.3 NAND Tree Order Pin # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 43 35 36 Pin Name VDD VSS SA18 SA19 IRQ9 DACK2# DREQ2 SYSCLK SD7 SD6 SD5 SD4 IOCHK# REFRESH# SD3 SD2 SD1 SD0 VDD VSS IOCHRDY SMEMR# AEN SMEMW# IOR# IOW# BALE MEMCS16# IOCS16# SA20 SA21 SA22 SA23 IRQ10 IRQ11 IRQ12 not in NAND chain (see Timing Diagram) first input in NAND chain Note Pin # 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 Pin Name IRQ15 IRQ14 VDD VSS DACK0# DREQ0 MEMR# MEMW# DACK5# DREQ5 SD8 SD9 SD10 SD11 DACK6# DREQ6 SD12 SD13 SD14 SD15 DACK7# DREQ7 VDD VSS MASTER# SBHE# TC BPD# AD31 AD30 AD29 AD28 AD27 AD26 VDD VSS AD25 intermediate NAND chain output Note 25 www.national.com 8.0 Electrical Characteristics (Continued) Pin # 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 Pin Name AD24 C/BE3# IDSEL AD23 AD22 VDD VSS AD21 AD20 AD19 AD18 AD17 AD16 C/BE2# FRAME# VDD VSS IRDY# TRDY# DEVSEL# STOP# SERR# PAR VDD VSS C/BE1# AD15 AD14 AD13 AD12 AD11 VDD VSS AD10 AD9 AD8 C/BE0# 133 143 135 136 137 138 139 140 141 142 143 144 145 146 DACK3# DREQ3 RSTDRV DACK1# DREQ1 PROHIBIT VDD VSS SA0 SA1 SA2 SA3 SA4 SA5 NAND chain output 125 126 127 128 129 130 131 132 PCPCIREQ# PCPCIGNT# SERIRQ IRQ3 IRQ4 IRQ5 IRQ6 IRQ7 not in NAND chain (see Timing Diagram) Note Pin # 111 112 113 114 115 116 117 118 119 120 121 122 123 124 Pin Name AD7 AD6 VDD VSS AD5 AD4 AD3 AD2 AD1 AD0 VDD VSS PCICLK PCIRST# (see Timing Diagram) not in NAND chain (see Timing Diagram) floating, not in NAND chain Note 26 www.national.com 8.0 Electrical Characteristics (Continued) Pin # 147 148 149 150 151 152 153 154 155 156 157 158 159 160 Pin Name SA6 SA7 SA8 VDD VSS SA9 SA10 SA11 SA12 SA13 SA14 SA15 SA16 SA17 end of NAND chain Note Note 1: All Vdd and Vss are not in the NAND chain. 27 www.national.com 8.0 Electrical Characteristics (Continued) in the NAND chain should be pulled high. Then release PCIRST#. After PCIRST# goes inactive, starting with Set PCIRST#, BALE and IRQ7 to low (PCPCIREQ# SA18 going counter-clockwise, switch each pin in the should be left floating), toggle PCICLK (provide a low-to- NAND chain low at a rate of at least about 100ns apart. high transition) at least once (recommended to provide two edges as show in the diagram below). All other pins 8.2.4 Timing Diagram for NAND test PCIRST# BALE, IRQ7 - stay low PCICLK t t t 2t t SA18 t SA19 t IRQ9 AD0 PCPCIGNT# t RSTDRV Note : t >= 100ns 28 www.national.com 8.0 Electrical Characteristics (Continued) effects. These effects can be minimized by filtering the DC power leads with low-inductance decoupling capacitors, 8.3.5 Unused Input Pins using low-impedance wiring, and by utilizing all of the VDD All inputs not used by the system designer should be kept and GND pins. at either ground or VDD. To prevent possible spurious oper8.4 Absolute Maximum Ratings ation, connect active-high inputs to ground through a 20kohm ( 10%) pull-down resistor and active-low inputs to Table 6. lists absolute maximum ratings for the PC87200. Stresses beyond the listed ratings may cause permanent VDD through a 20-kohm ( 10%) pull-up resistor . damage to the device. Exposure to conditions beyond these lim8.3.6 NC-Designated Pins its may (1) reduce device reliability and (2) result in premaPins designated NC should be left disconnected. Connect- ture failure even when there is no immediately apparent ing an NC pin to a pull-up resistor, pull-down resistor, or an sign of failure. Prolonged exposure to conditions at or near active signal could cause unexpected results and possible the absolute maximum ratings may also result in reduced circuit malfunctions. useful life and reliability These are stress ratings only and 8.3.7 Power and Ground Connections and Decoupling do not imply that operation under any conditions other than those listed under Table 7. is possible. Testing and operating the PC87200 requires the use of standard high frequency techniques to reduce parasitic Table 6. Absolute Maximum Ratings Parameter Operating Case Temperature Storage Temperature Supply Voltage Voltage On Any Pin: –0.5 –65 Min Max 110 150 4.0 5.5 Units ˚C ˚C V V No Bias Comment 8.3 Electrical Connections 8.5 Recommended Operating Conditions Table 7. lists the recommended operating conditions for the PC87200. Table 7. Recommended Operating Conditions Symbol TA VDD Parameter Ambient Temperature Supply Voltage Min 0 3.0 Max 70 3.6 Units ˚C V 3.3 V nominal Comment 29 www.national.com 8.0 Electrical Characteristics (Continued) 8.6 DC Characteristics Table 8. DC Characteristics (at Recommended Operating Conditions) Symbol Parameter Min Typ Max Units Comment ISA bus (including PROHIBIT, BPD#) VIL VIH VOL VOH IOHL VILC VIHC VOLC VOHC Input Low Voltage Input High Voltage Output Low Voltage Output High Voltage Output High Leakage 2.4 200 –0.5 2.0 0.8 VDD+0.5 0.5 V V V V uA TTL Level Inputs TTL Level Inputs Iol=12 mA Ioh=-3mA Vo=Vcc, for OD driver PCI bus (including PCPCIREQ#, PCPCIGNT#, SERIRQ) Input Low Voltage Input High Voltage Output Low Voltage Output High Voltage 0.9VDD 15 10 10 10 –0.5 0.5VDD 0.3VDD VDD+0.5 0.1VDD V V V V CMOS Level Inputs CMOS Level Inputs Iout=1500uA Iout=-500uA All pins II CIN COUT CCLK ICC ICCSS Input Leakage Current for each input pin Input Capacitance Output or I/O Capacitance CLK Input Capacitance A pF pF pF 0 < VIN < VDD, f = 1MHz f = 1MHz f = 1MHz Current Consumption Active ICC: PCICLK @ 33 MHz Standby ICC (PCICLK Stopped) 30 10 160 mA uA fPCICLK = 0MHz 30 www.national.com 8.0 Electrical Characteristics (Continued) 8.7 AC Characteristics The following tables list the AC characteristics including output delays, input setup requirements, input hold requirements and output float delays. The rising-clock-edge reference level VREF and other reference levels are shown in Table 9. , Input or output signals must cross these levels during testing. Input setup and hold times are specified minimums that define the smallest acceptable sampling window for which a synchronous input signal must be stable for correct operation. Note: All AC tests are at VDD = 3.0V to 3.6V, TA = 0oC to 70oC, CL = 50pF unless otherwise specified. Table 9. Drive Level and Measurement Points for Switching Characteristics Symbol VREF VIHD VILD Voltage (V) 1.5 2.3 0.3 TX CLK VIHD VILD A B Min Valid Output n+1 Max VREF OUTPUTS Valid Output n VREF C INPUTS VIHD VILD Valid Input D VREF Legend: A = Maximum Output Delay Specification B = Minimum Output Delay Specification C = Minimum Input Setup Specification D = Minimum Input Hold Specification Figure 4. Drive Level and Measurement Points for Switching Characteristics Table 10. AC Characteristics of Specification Compliant Interface Signals Interface Signal Group PCI Bus Interface Signals ISA Bus Interface Signals Specification Name PCI Bus Specification, Revision 2.1 Abides industry standards The interface signal groups listed in Table 11. adhere to the timing parameters given in the corresponding specification. For details, refer to those specifications. 31 www.national.com 8.0 Electrical Characteristics (Continued) Table 11. Clock Characteristics Symbol Input Signal tcyc tHIGH tLOW -PCICLK Cycle Time PCICLK High Time PCICLK Low Time PCICLK Slew Time 30 11 11 1 4 ∞ ns ns ns V/ns Note 1 Parameter Min Max Duty Cycle Unit Comment Note 1: Rise and fall times are specified in terms of the edge rate measured in V/ns. This slew rate must be met across the minimum peak-to-peak portion of the clock waveform as shown in Figure 5.. tcyc tHIGH 0.6 VCC 0.5 VCC 0.4 VCC 0.3 VCC 0.2 VCC 0.4 VCC, p-to-p (minimum) tLOW Figure 5. PCICLK Waveform 32 www.national.com PC87200 PCI to ISA Bridge 9.0 Physical Dimensions inches (millimeters) unless otherwise noted 160 Lead Molded Plastic Quad Flat Package (JEDEC) Order Number PC87200160A NS Package Number VUL160A LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: support@nsc.com National Semiconductor Europe Fax: (+49) 0-180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: English Tel: (+49) 0-180-530 85 85 (+49) 0-180-532 78 32 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-254-4466 Fax: 65-250-4466 Email: sea.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5620-6175 Fax: 81-3-5620-6179 www.national.com National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.