NTE56028

NTE56028 TRIAC, 40 Amp Description: The NTE56028 is a 40 Amp TRIAC is a TO220 type package designed primarily for full−wave AC control applications such as lighting systems, heater controls, motor controls, and power supplies. Features: D Blocking Voltage of 800V D All Diffused and Glass−Passivated Junctions for Parameter Uniformity and Stability D Gate Triggering Guaranteed in Four Modes Absolute Maximum Ratings: Peak Repetitive Off−State Voltage, VDRM (TJ = −40° to +125°C, 1/2 Sine Wave 50 to 60Hz, Gate Open, Note 1) . . . . . . . . . . . . . 800V On−State RMS Current (TC = +75°C, Full Cycle Sine Wave 50 to60Hz, Note 2), IT(RMS) . . . . 40A Peak Non−Repetitive Surge Current (TJ = +125°C, One Full Cycle, 60Hz), ITSM . . . . . . . . . . . 350A Circuit Fusing (t = 8.3ms), I2t . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500A2s Peak Gate Current (t ≤ 2µs), IGM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±2A Peak Gate Voltage (t ≤ 2µs), VGM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±10V Peak Gate Power (t ≤ 2µs), PGM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20W Average Gate Power (TC = +75°C, t ≤ 8.3ms), PG(AV) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5W Operating Junction Temperature Range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40° to +125°C Storage Temperature Range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40° to +150°C Thermal Resistance, Junction−to−Case, RthJC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1°C/W Thermal Resistance, Junction−to−Ambient, RthJA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60°C/W Mounting Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8in. lb. Note 1. Ratings apply for open gate conditions. Devices shall not be tested with a constant current source for blocking voltage such that the voltage applied exceeds the rated blocking voltage. Note 2. This device is rated for use in applications subject to high surge conditions. Care must be taken to insure proper heat sinking when the device is to be used at high sustained currents. Electrical Characteristics: (TC = +25°C and either polarity of MT1 to MT2 voltage unless otherwise specified) Parameter Symbol Peak Forward Blocking Current IDRM Peak Reverse Blocking Current IRRM Peak On−State Voltage VTM Gate Trigger Current (Continuous DC) MT2 (+), G (+); MT2 (−), G (−); MT2 (+), G (−) IGT Test Conditions Min Typ Max Unit VDRM = 800V, TJ = +25°C − − 10 µA VDRM = 800V, TJ = +125°C − − 2 mA VRRM = 800V, TJ = +25°C − − 10 µA VRRM = 800V, TJ = +125°C − − 2 mA ITM = 56A (Peak), Note 3 − 1.40 1.85 V VD = 12V, RL = 100Ω, − 25 50 mA − 40 75 mA − 1.1 2.0 V − 1.3 2.5 V 0.2 − − V 0.2 − − V MT2 (−), G (+) Gate Trigger Voltage (Continuous DC) MT2 (+), G (+); MT2 (−), G (−); MT2 (+), G (−) VGT VD = 800V, RL = 100Ω, MT2 (−), G (+) Gate Non−Trigger Voltage MT2 (+), G (+); MT2 (−), G (−); MT2 (+), G (−) VGD VD = 800V, TJ = +125°C, RL = 10k, MT2 (−), G (+) Holding Current IH VD = 12V, Gate Open − 30 75 mA Gate Controlled Turn−On Time tgt VD = 800V, ITM = 56A (Peak), IGT = 200mA − 1.5 − µs VD = 800V, Exponential Waveform, TC = +125°C − 50 − V/µs VD = 800V, ITM = 56A (Peak), Commutating di/dt = 13.4A/ms, Gate Unenergized, TC = +75°C − 5 − V/µs Critical Rate of Rise of Off−State Voltage dv/dt Critical Rate 0f Rise of Commutation Voltage dv/dt(c) Note 3. Pulse Width ≤ 2ms, Duty Cycle ≤ 2%. .420 (10.67) Max .110 (2.79) .147 (3.75) Dia Max .500 (12.7) Max .250 (6.35) Max .070 (1.78) Max MT1 .100 (2.54) .500 (12.7) Min Gate MT2/Tab* * NOTE: Tab may be isolated.