SIT100M250

105°C SNAP–IN ALUMINUM ELECTROLYTIC SIT SERIES SUBMINIATURE (SIT: High Temperature Snap–in) The SIT Snap–in series subminiature aluminum electrolytic capacitors are especially suitable for applications requiring high capacitance, low cost, and very small size. In fact, you’ll find these capacitors in some of the most demanding applications, from precision medical electronics and automobiles to the newest personal computers and disk drives. They operate over a broad temperature range and are available in either blister pack or bulk. MECHANICAL SPECIFICATIONS Marking: Consists of series type, nominal capacitance, rated voltage, temperature range, anode and/or cathode identification, vendor identification. Recommended Cleaning Solvents: Chlorofluorocarbon solvents used to remove flux from printed circuit boards can penetrate the capacitor end– seals, cause corrosion when voltage is applied and capacitor failure. Avoid halogenated solvents and consider these alternatives: Clean the capacitors with water/detergent or cleaning solvents free of halogen groups such as alcohol or terpene solution, or mount the capacitor after board cleaning. RATINGS Capacitance Range: 100µf to 10,000µf Tolerance: ±20% Voltage Range: 50V to 250V PERFORMANCE SPECIFICATIONS Operating Temperature Range: –40°C to +105°C (–40°F to +221°F) Leakage Current: I ≤ 3 x √CV (measured after 5 minutes @ rated voltage and +20°C (+68°F) I = Leakage Current (µA) C = Nominal Capacitance (µf) V = Rated Voltage (V) Capacitance Tolerance (M): ±20% measured at +20°C (+68°F), 120HZ Surge Voltage: DC Rated Voltage Surge Voltage 50 63 200 250 250 300 CASE SIZE AND DIMENSIONS: SIT SERIES 10.0 Polarity Bar Safety Vent Vinyl Sleeve L+2 Max 2 ±0.1 Dia 10 ±0.1 6.3 ±1 DØ+1 Max 0.8 –0.1 +0.2 2.0 Max 1.5 ±0.2 6.3 ±1 4.0 Load Life: 2000 ±12Hrs @ Max rated temperature and rated voltage Leakage Current: Within values specified above Dissipation Factor: Within ±150% of specified value Shelf Life: 1000 ±6Hrs @ Max rated temperature, no voltage applied Leakage Current: Within ±200% of specified value Dissipation Factor: Within ±150% of specified value Capacitance Change Max: Within ±20% of initial value DØ PC Board Mounting Holes Terminal ORDERING INFORMATION SIT Series Capacitance Tolerance Voltage 1000 M 50 14 NTE Electronics, Inc. D Voice (800) 631–1250 (973) 748–5089 D FAX (973) 748–6224 D http://www.nteinc.com 105°C SNAP–IN ALUMINUM ELECTROLYTIC SIT SERIES SIT Series Dimensions: Diameter (D Ø) x Length (L): mm WV Cap (µf) 100 150 220 330 470 560 680 820 1000 1500 2200 3300 4700 6800 8200 10000 22 x 40 22 x 50 22 x 45 30 x 50 30 x 45 30 x 50 22 x 25 50 200 22 x 20 22 x 30 22 x 40 22 x 50 22 x 40 22 x 45 22 x 45 25 x 50 30 x 45 35 x 50 250 22 x 30 22 x 40 22 x 50 22 x 40 30 x 35 25 x 50 30 x 45 30 x 50 35 x 45 * These dimensions are for reference only, please consult the factory for actual size. NTE Electronics, Inc. D Voice (800) 631–1250 (973) 748–5089 D FAX (973) 748–6224 D http://www.nteinc.com 15