08052F105M7BB0D

DATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS Class 2, Y5V 16/25/50 V Product Specification – Jul 08, 2003 V.7 Phycomp Product specification Surface-mount ceramic multilayer capacitors FEATURES • Five standard sizes • High capacitance per unit volume • Supplied in tape on reel • NiSn terminations. QUICK REFERENCE DATA DESCRIPTION Rated voltage UR (DC) Capacitance range (E6 series) Tolerance on capacitance Test voltage (DC) for 1 minute: Sectional specifications APPLICATIONS • Consumer electronics, for example: − Tuners − Television receivers − Video recorders − All types of cameras − Mobile telephones. terminations Class 2, Y5V 16/25/50 V VALUE 16 V, 25 V, 50 V 10 nF to 10 µF; note 1 ±20% (M); −20% to +80% (Z) 2.5 × UR IEC 60384-10, second edition 1989-04 based on IEC 60384-10-1 NiSn 30/85/21 Detailed specification End terminations Climatic category (IEC 60068) Note 1. Measured at 25 °C, 1 V and 1 kHz, using a four-gauge method. DESCRIPTION The capacitor consists of a rectangular block of ceramic dielectric in which a number of interleaved metal electrodes are contained. This structure gives rise to a high capacitance per unit volume. The inner electrodes are connected to the two terminations and finally covered with a layer of plated tin (NiSn). A cross section of the structure is shown in Fig.1. electrodes MLB457 ceramic material Fig.1 Construction of a ceramic multilayer capacitor. 2003 Jul 08 Rev.7 2 www.yageo.com Phycomp Product specification Surface-mount ceramic multilayer capacitors MECHANICAL DATA Class 2, Y5V 16/25/50 V T W L2 L4 L1 L3 MBB211 For dimensions see Table 1. Fig.2. Component outline. Physical dimensions Table 1 Capacitor dimensions; see Fig.2 L1 W MIN. 0.5 ±0.05 0.8 ±0.07 1.25 ±0.10 1.6 ±0.15 2.5 ±0.20 0.020 ±0.002 0.032 ±0.003 0.049 ±0.004 0.063 ±0.006 0.098 ±0.008 0.45 0.73 0.50 0.50 1.40 0.018 0.029 0.020 0.020 0.047 T MAX. 0.55 0.87 1.35 1.75 1.60 0.022 0.035 0.053 0.069 0.069 L2 and L3 . MIN. 0.15 0.25 0.25 0.25 0.25 0.008 0.010 0.010 0.010 0.010 MAX. 0.30 0.65 0.75 0.75 0.75 0.012 0.026 0.030 0.030 0.030 L4 MIN. CASE SIZE Dimensions in millimetres 0402 0603 0805 1206 1210 0402 0603 0805 1206 1210 1.0 ±0.05 1.6 ±0.10 2.0 ±0.10 3.2 ±0.15 3.2 ±0.20 0.040 ±0.002 0.063 ±0.004 0.079 ±0.004 0.126 ±0.006 0.126 ±0.008 0.40 0.40 0.55 1.40 1.40 0.016 0.016 0.022 0.056 0.056 Dimensions in inches 2003 Jul 08 Rev.7 3 www.yageo.com Phycomp Product specification Surface-mount ceramic multilayer capacitors SELECTION CHART FOR 16 V AND 25 V LAST TWO DIGITS OF 12NC 23 25 27 29 32 34 36 38 41 43 45 47 49 52 54 56 58 61 63 65 67 69 72 76 1.5 ±0.1 1.15 ±0.1 1.25 ±0.1 0.85 ±0.1 0.85 ±0.1 1.25 ±0.1 0.8 ±0.07 0.6 ±0.1 0.85 ±0.1 0.5 ±0.05 0.8 ±0.07 16 V 0402 0603 0805 1206 1210 0603 0805 Class 2, Y5V 16/25/50 V 25 V 1206 1210 C (nF) 1 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 330 470 680 1 000 1 500 2 200 3 300 4 700 10 000 Note 0.6 ±0.1 0.85 ±0.1 1.15 ±0.1 1.5 ±0.1 1. Values in shaded cells indicate thickness class in mm. 2003 Jul 08 Rev.7 4 www.yageo.com Phycomp Product specification Surface-mount ceramic multilayer capacitors SELECTION CHART FOR 50 V LAST TWO DIGITS OF 12NC 05 06 07 08 09 11 12 13 14 15 16 17 18 1.25 ±0.1 0.85 ±0.1 0.8 ±0.07 0.6 ±0.1 50 V 0603 0805 Class 2, Y5V 16/25/50 V C (nF) 1206 10 15 22 33 47 68 100 150 220 330 470 680 1 000 Note 0.6 ±0.1 0.85 ±0.1 1.15 ±0.1 1. Values in shaded cells indicate thickness class in mm. Thickness classification and packing quantities THICKNESS CLASSIFICATION (mm) 0.5 ±0.05 0.6 ±0.10 0.8 ±0.07 0.85 ±0.10 1.15 ±0.10 1.25 ±0.10 1.5 ±0.10 8 mm TAPE WIDTH QUANTITY PER REEL ∅180 mm; 7" PAPER 10 000 4 000 4 000 4 000 − − − BLISTER − − − − 3 000 3 000 3 000 ∅330 mm; 13" PAPER 50 000 20 000 15 000 15 000 − − − BLISTER − − − − 10 000 1 000 − 50 000 − − − − − − − − 15 000 15 000 − − − − 10 000 − 8 000 − 5 000 − QUANTITY PER BULK CASE 0402 0603 0805 2003 Jul 08 Rev.7 5 www.yageo.com Phycomp Product specification Surface-mount ceramic multilayer capacitors ORDERING INFORMATION Class 2, Y5V 16/25/50 V Components may be ordered by using either a Phycomp’s unique 12NC or simple 15-digit clear text code. Ordering code 12NC (preferred) handbook, full pagewidth 22XX XXX X9XXX Capacitance value(1) Carrier type 22 blister 38 paper 54 bulk Rated voltage - Termination 78 16 V; NiSn 91 25 V; NiSn 58 50 V; NiSn Size 7 0402 6 0603 0 0805 1 1206 2 1210 Tolerance 7 ±20% 8 −20/+80% CCA620_a Packaging(2) 1 reel: ∅180 mm; 7" 5 reel: ∅330 mm; 13" 4 bulk case (1) (2) Refer to chapters “Selection chart for 16 V and 25 V” and “Selection chart for 50 V”. Quantity on reel depends on thickness classification, see section “Thickness classification and packing quantities”. Phycomp Clear text code EXAMPLE: 12062F105M8BB0D Size Code 0402 0603 0805 1206 1210 Temp. Char. Capacitance Tol. Vol. Termination B = NiSn Packing 2 = 180 mm; 7" paper 3 = 330 mm; 13" paper B = 180 mm; 7" blister F = 330 mm; 13" blister P = bulk case Marking 0 = no marking Series D = BME 7 = 16 V 2F = Y5V 105 = 1000000 M = ±20% pF; the third digit Z = −20% /+80% 8 = 25 V 9 = 50 V signifies the multiplying factor: 2 = × 100 3 = × 1000 4 = × 10 000 5 = × 100 000 6 = × 1 000 000 2003 Jul 08 Rev.7 6 www.yageo.com Phycomp Product specification Surface-mount ceramic multilayer capacitors ELECTRICAL CHARACTERISTICS Class 2 capacitors; Y5V dielectric; NiSn terminations Class 2, Y5V 16/25/50 V Unless otherwise stated all electrical values apply at an ambient temperature of 25 ±1 °C, an atmospheric pressure of 86 to 105 kPa, and a relative humidity of 63 to 67%. DESCRIPTION Capacitance range (E6 series); note 1 Tolerance on capacitance after 1000 hours Tan δ; note 1: all 25 V and 50 V except 0805 ≥ 330 nF; 0603 /100 nF; 1206 /1 µF; 1210 /10 µF sizes 0805 / 330 nF; 0603 / 100 nF; 1206 /1 　F 25 V 0805 ≥ 470 nF 1210 /10 µF all 16 V except 0402; 0603 ≥ 330 nF; 0805 ≥ 1.5 µF; 1206 ≥ 3.3 µF; 1210 /10 µF sizes 0402; 0603 ≥ 330 nF; 0805 ≥ 1.5 µF; 1206 ≥ 3.3 µF; 1210 /10 µF Insulation resistance after 1 minute at UR (DC): Maximum capacitance change with respect to capacitance at 25 °C (for typical values see Fig.5) Ageing Resistance to soldering heat Note 1. Measured at 25 °C, 1 V, 1 kHz, using a four-gauge method. ≤9% ≤12.5% Rins >10 GΩ or Rins × C ≥500 seconds whichever is less +22% to −82% typical 7% per time decade 260 °C; 10 seconds ≤9% ≤12.5% ≤5% ≤7% 10 nF to 10 µF ±20% (M); −20% to +80% (Z) VALUE 2003 Jul 08 Rev.7 7 www.yageo.com Phycomp Product specification Surface-mount ceramic multilayer capacitors Class 2, Y5V 16/25/50 V ∆C C (%) 0 MBD076 2000 MBD078 20 tan δ (x 10 4 ) 1500 40 60 1000 80 500 100 0 10 20 30 40 50 V DC (V) 0 25 0 25 50 75 100 T ( oC) Fig.3 Typical capacitance change with respect to the capacitance at 1 V as a function of DC voltage at 25 °C. Fig.4 Typical tan δ as a function of temperature. ∆C C (%) 25 MBD077 0 25 50 75 100 25 0 25 50 75 100 T ( oC) Fig.5 Typical capacitance change as a function of temperature. 2003 Jul 08 Rev.7 8 www.yageo.com Phycomp Product specification Surface-mount ceramic multilayer capacitors TESTS AND REQUIREMENTS Table 2 Test procedures and requirements IEC 60068-2 TEST METHOD Class 2, Y5V 16/25/50 V IEC 60384-10/ CECC 32 100 CLAUSE 4.4 TEST PROCEDURE REQUIREMENTS mounting the capacitors may be mounted on printed-circuit boards or ceramic substrates by applying wave soldering, reflow soldering (including vapour phase soldering) or conductive adhesive any applicable method using ×10 magnification f = 1 kHz; Y5V measuring voltage 1 Vrms at 25 °C f = 1 kHz; Y5V measuring voltage 1 Vrms at 25 °C at UR (DC) for 1 minute 2.5 × UR for 1 minute between minimum and maximum temperature a force of 5 N applied for 10 s to the line joining the terminations and in a plane parallel to the substrate mounted in accordance with IEC 60384-1, paragraph 4.35 conditions: bending 1 mm at a rate of 1 mm/s, radius jig 340 mm no visible damage 4.5 4.6.1 4.6.2 4.6.3 4.6.4 4.7.1 4.8 visual inspection and dimension check capacitance tan δ insulation resistance voltage proof temperature coefficient adhesion in accordance with specification within specified tolerance in accordance with specification RiCR ≥500 s no breakdown or flashover in accordance with specification no visible damage 4.9 bond strength of plating on end face no visible damage ∆C/C: ≤30% 4.10 Tb resistance to soldering heat preconditioning: 120 to 150 °C during 1 minute; 260 ±5 °C for 10 ±0.5 s in a static solder bath 260 ±5 °C for 30 ±1 s in a static solder bath the terminations shall be well tinned after recovery ∆C/C: ±20% tan δ: original specification Rins: original specification using visual enlargement of ×10, dissolution of the terminations shall not exceed 10% resistance to leaching 2003 Jul 08 Rev.7 9 www.yageo.com Phycomp Product specification Surface-mount ceramic multilayer capacitors IEC 60384-10/ CECC 32 100 CLAUSE 4.11 IEC 60068-2 TEST METHOD Ta Class 2, Y5V 16/25/50 V TEST PROCEDURE REQUIREMENTS solderability zero hour test, and test after storage (20 to 24 months) in original packing in normal atmosphere; unmounted chips completely immersed for 2 ±0.5 s in a solder bath at 235 ±5 °C preconditioning: between minimum and maximum temperature, 5 cycles initialization: 48 ±4 hours after UR at 40 °C for 1 hour (for initial value measurement); 500 ±12 hours at 40 °C; 90 to 95% RH; UR applied initialization: 48 hours after UR at 40 °C; for 1 hour (for initial value measurement); 500 ±12 hours at 40 °C; 90 to 95% RH; UR applied the terminations shall be well tinned 4.12 Na rapid change of temperature damp heat, steady state no visible damage after 48 hours recovery: ∆°C/C: ≤ ±20% no visible damage after 48 hours recovery: ∆°C/C: +30%/−40% tan δ: ≤15% Rins: 500 MΩ or RiCR ≥ 100 s, whichever is less preconditioning: UR at 40 °C for 1 hour, after 48 hours recovery: ∆°C/C: +30%/−40% tan δ: ≤15% Rins: 500 MΩ or RiCR ≥ 25 s, whichever is less after 48 hours recovery: ∆°C/C: +30%/−40% tan δ: ≤15% Rins: 1000 MΩ or RiCR ≥ 50 s, whichever is less 4.14 Ca damp heat; with UR load 4.15 endurance initialization: 2 × UR at 85 °C for 1 hour, (initial value measurement after 48 ±4 hours) ; 2 × UR at 85 °C for 1000 hours recovery 48 ±4 hours at room temperature 2003 Jul 08 Rev.7 10 www.yageo.com Phycomp Product specification Surface-mount ceramic multilayer capacitors REVISION HISTORY Revision Rev.7 Date 2003 Jul 08 Change Notification − Description - Updated company logo Class 2, Y5V 16/25/50 V 2003 Jul 08 Rev.7 11 www.yageo.com