74AUP2G241
Low-power dual buffer/line driver; 3-state
Rev. 7 — 11 February 2013
Product data sheet
1. General description
The 74AUP2G241 provides a dual non-inverting buffer/line driver with 3-state outputs.
The 3-state outputs are controlled by the output enable inputs 1OE and 2OE. A HIGH
level at pin 1OE causes output 1Y to assume a high-impedance OFF-state. A LOW level
at pin 2OE causes output 2Y to assume a high-impedance OFF-state.
Schmitt trigger action at all inputs makes the circuit tolerant to slower input rise and fall
times across the entire VCC range from 0.8 V to 3.6 V.
This device ensures a very low static and dynamic power consumption across the entire
VCC range from 0.8 V to 3.6 V.
This device is fully specified for partial power-down applications using IOFF.
The IOFF circuitry disables the output, preventing the damaging backflow current through
the device when it is powered down.
This device has an input-disable feature, which allows floating input signals. The input 1A
is disabled when the output enable input 1OE is HIGH. The input 2A is disabled when the
output enable input 2OE is LOW.
2. Features and benefits
Wide supply voltage range from 0.8 V to 3.6 V
High noise immunity
Complies with JEDEC standards:
JESD8-12 (0.8 V to 1.3 V)
JESD8-11 (0.9 V to 1.65 V)
JESD8-7 (1.2 V to 1.95 V)
JESD8-5 (1.8 V to 2.7 V)
JESD8-B (2.7 V to 3.6 V)
ESD protection:
HBM JESD22-A114F Class 3A exceeds 5000 V
MM JESD22-A115-A exceeds 200 V
CDM JESD22-C101E exceeds 1000 V
Low static power consumption; ICC = 0.9 A (maximum)
Latch-up performance exceeds 100 mA per JESD 78 Class II
Inputs accept voltages up to 3.6 V
Low noise overshoot and undershoot < 10 % of VCC
Input-disable feature allows floating input conditions
IOFF circuitry provides partial Power-down mode operation
74AUP2G241
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
Multiple package options
Specified from 40 C to +85 C and 40 C to +125 C
3. Ordering information
Table 1.
Ordering information
Type number
Package
Temperature range
Name
Description
74AUP2G241DC
40 C to +125 C
VSSOP8
plastic very thin shrink small outline package; 8 leads; SOT765-1
body width 2.3 mm
Version
74AUP2G241GT
40 C to +125 C
XSON8
plastic extremely thin small outline package; no leads; SOT833-1
8 terminals; body 1 1.95 0.5 mm
74AUP2G241GF
40 C to +125 C
XSON8
extremely thin small outline package; no leads;
8 terminals; body 1.35 1 0.5 mm
74AUP2G241GD
40 C to +125 C
XSON8
plastic extremely thin small outline package; no leads; SOT996-2
8 terminals; body 3 2 0.5 mm
74AUP2G241GM
40 C to +125 C
XQFN8
plastic, extremely thin quad flat package; no leads;
8 terminals; body 1.6 1.6 0.5 mm
SOT902-2
74AUP2G241GN
40 C to +125 C
XSON8
extremely thin small outline package; no leads;
8 terminals; body 1.2 1.0 0.35 mm
SOT1116
74AUP2G241GS
40 C to +125 C
XSON8
extremely thin small outline package; no leads;
8 terminals; body 1.35 1.0 0.35 mm
SOT1203
SOT1089
4. Marking
Table 2.
Marking codes
Type number
Marking code[1]
74AUP2G241DC
p41
74AUP2G241GT
p41
74AUP2G241GF
p1
74AUP2G241GD
p41
74AUP2G241GM
p41
74AUP2G241GN
p1
74AUP2G241GS
p1
[1]
The pin 1 indicator is located on the lower left corner of the device, below the marking code.
74AUP2G241
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 11 February 2013
© NXP B.V. 2013. All rights reserved.
2 of 26
74AUP2G241
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
5. Functional diagram
1OE
1A
1Y
1
EN1
2OE
2A
2Y
2
EN2
001aah730
Fig 1.
001aah731
Logic symbol
Fig 2.
IEC logic symbol
6. Pinning information
6.1 Pinning
74AUP2G241
1OE
1
8
VCC
1A
2
7
2OE
2Y
3
6
1Y
GND
4
5
2A
74AUP2G241
1OE
1
8
VCC
1A
2
7
2OE
2Y
3
6
1Y
GND
4
5
2A
001aaf438
Transparent top view
001aaf437
Fig 3.
Pin configuration SOT765-1
74AUP2G241
Product data sheet
Fig 4.
Pin configuration SOT833-1, SOT1089,
SOT1116 and SOT1203
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 11 February 2013
© NXP B.V. 2013. All rights reserved.
3 of 26
74AUP2G241
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
74AUP2G241
74AUP2G241
1
8
VCC
1A
2
7
2OE
2Y
3
6
1Y
GND
4
5
2A
1
1Y
2A
8
2OE
7
1OE
2
6
1A
3
5
2Y
GND
4
1OE
VCC
terminal 1
index area
001aaj394
Transparent top view
Transparent top view
Fig 5.
001aaf439
Pin configuration SOT996-2
Fig 6.
Pin configuration SOT902-2
6.2 Pin description
Table 3.
Symbol
1OE
Pin description
Pin
Description
SOT765-1, SOT833-1, SOT1089,
SOT996-2, SOT1116 and SOT1203
SOT902-2
1
7
output enable input 1OE (active LOW)
1A, 2A
2, 5
6, 3
data input
1Y, 2Y
6, 3
2, 5
data output
GND
4
4
ground (0 V)
2OE
7
1
output enable input 2OE (active HIGH)
VCC
8
8
supply voltage
7. Functional description
Table 4.
Function table[1]
Input
Output
Input
1OE
1A
1Y
2OE
2A
2Y
L
L
L
H
L
L
L
H
H
H
H
H
H
X
Z
L
X
Z
[1]
Output
H = HIGH voltage level; L = LOW voltage level; X = don’t care; Z = high-impedance OFF-state.
74AUP2G241
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 11 February 2013
© NXP B.V. 2013. All rights reserved.
4 of 26
74AUP2G241
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
8. Limiting values
Table 5.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
Symbol
Parameter
VCC
supply voltage
IIK
input clamping current
VI
input voltage
IOK
output clamping current
Conditions
Min
Max
Unit
0.5
+4.6
V
50
-
mA
0.5
+4.6
V
50
-
mA
0.5
+4.6
V
VI < 0 V
[1]
VO < 0 V
[1]
VO
output voltage
Active mode and Power-down mode
IO
output current
VO = 0 V to VCC
-
20
mA
ICC
supply current
-
+50
mA
IGND
ground current
50
-
mA
Tstg
storage temperature
65
+150
C
-
250
mW
[1]
[2]
Tamb = 40 C to +125 C
total power dissipation
Ptot
[2]
The minimum input and output voltage ratings may be exceeded if the input and output current ratings are observed.
For VSSOP8 packages: above 110 C the value of Ptot derates linearly with 8.0 mW/K.
For XSON8 and XQFN8 packages: above 118 C the value of Ptot derates linearly with 7.8 mW/K.
9. Recommended operating conditions
Table 6.
Operating conditions
Symbol
Parameter
VCC
supply voltage
VI
input voltage
VO
output voltage
Conditions
Tamb
ambient temperature
t/V
input transition rise and fall rate
Min
Max
Unit
0.8
3.6
V
0
3.6
V
Active mode
0
VCC
V
Power-down mode; VCC = 0 V
0
3.6
V
40
+125
C
0
200
ns/V
VCC = 0.8 V to 3.6 V
10. Static characteristics
Table 7.
Static characteristics
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Symbol Parameter
Conditions
Min
Typ
VCC = 0.8 V
0.70 VCC -
Max
Unit
-
V
Tamb = 25 C
VIH
VIL
HIGH-level input voltage
LOW-level input voltage
74AUP2G241
Product data sheet
VCC = 0.9 V to 1.95 V
0.65 VCC -
-
V
VCC = 2.3 V to 2.7 V
1.6
-
-
V
VCC = 3.0 V to 3.6 V
2.0
-
-
V
VCC = 0.8 V
-
-
0.30 VCC V
VCC = 0.9 V to 1.95 V
-
-
0.35 VCC V
VCC = 2.3 V to 2.7 V
-
-
0.7
V
VCC = 3.0 V to 3.6 V
-
-
0.9
V
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 11 February 2013
© NXP B.V. 2013. All rights reserved.
5 of 26
74AUP2G241
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
Table 7.
Static characteristics …continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Symbol Parameter
Conditions
VOH
VI = VIH or VIL
VOL
HIGH-level output voltage
LOW-level output voltage
Min
Typ
Max
Unit
IO = 20 A; VCC = 0.8 V to 3.6 V
VCC 0.1
-
-
V
IO = 1.1 mA; VCC = 1.1 V
0.75 VCC -
-
V
IO = 1.7 mA; VCC = 1.4 V
1.11
-
-
V
IO = 1.9 mA; VCC = 1.65 V
1.32
-
-
V
IO = 2.3 mA; VCC = 2.3 V
2.05
-
-
V
IO = 3.1 mA; VCC = 2.3 V
1.9
-
-
V
IO = 2.7 mA; VCC = 3.0 V
2.72
-
-
V
IO = 4.0 mA; VCC = 3.0 V
2.6
-
-
V
IO = 20 A; VCC = 0.8 V to 3.6 V
-
-
0.1
V
IO = 1.1 mA; VCC = 1.1 V
-
-
0.3 VCC
V
IO = 1.7 mA; VCC = 1.4 V
-
-
0.31
V
IO = 1.9 mA; VCC = 1.65 V
-
-
0.31
V
IO = 2.3 mA; VCC = 2.3 V
-
-
0.31
V
IO = 3.1 mA; VCC = 2.3 V
-
-
0.44
V
IO = 2.7 mA; VCC = 3.0 V
-
-
0.31
V
IO = 4.0 mA; VCC = 3.0 V
-
-
0.44
V
VI = VIH or VIL
II
input leakage current
VI = GND to 3.6 V; VCC = 0 V to 3.6 V
-
-
0.1
A
IOZ
OFF-state output current
VI = VIH or VIL; VO = 0 V to 3.6 V;
VCC = 0 V to 3.6 V
-
-
0.1
A
IOFF
power-off leakage current
VI or VO = 0 V to 3.6 V; VCC = 0 V
-
-
0.2
A
IOFF
additional power-off leakage VI or VO = 0 V to 3.6 V;
current
VCC = 0 V to 0.2 V
-
-
0.2
A
ICC
supply current
VI = GND or VCC; IO = 0 A;
VCC = 0.8 V to 3.6 V
-
-
0.5
A
ICC
additional supply current
data input; VI = VCC 0.6 V; IO = 0 A;
VCC = 3.3 V
[1]
-
-
40
A
1OE and 2OE input; VI = VCC 0.6 V;
IO = 0 A; VCC = 3.3 V
[1]
-
-
110
A
all inputs; VI = GND to 3.6 V;
1OE = VCC; 2OE = GND;
VCC = 0.8 V to 3.6 V
[2]
-
-
1
A
-
0.6
-
pF
CI
input capacitance
VCC = 0 V to 3.6 V; VI = GND or VCC
CO
output capacitance
output enabled; VO = GND; VCC = 0 V
-
1.7
-
pF
output disabled; VCC = 0 V to 3.6 V; VO
= GND or VCC
-
1.5
-
pF
VCC = 0.8 V
0.70 VCC -
-
V
VCC = 0.9 V to 1.95 V
0.65 VCC -
-
V
VCC = 2.3 V to 2.7 V
1.6
-
-
V
VCC = 3.0 V to 3.6 V
2.0
-
-
V
Tamb = 40 C to +85 C
VIH
HIGH-level input voltage
74AUP2G241
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 11 February 2013
© NXP B.V. 2013. All rights reserved.
6 of 26
74AUP2G241
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
Table 7.
Static characteristics …continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Symbol Parameter
Conditions
Min
Typ
Max
VIL
VCC = 0.8 V
-
-
0.30 VCC V
VCC = 0.9 V to 1.95 V
-
-
0.35 VCC V
VCC = 2.3 V to 2.7 V
-
-
0.7
V
VCC = 3.0 V to 3.6 V
-
-
0.9
V
IO = 20 A; VCC = 0.8 V to 3.6 V
VCC 0.1
-
-
V
VOH
VOL
LOW-level input voltage
HIGH-level output voltage
LOW-level output voltage
Unit
VI = VIH or VIL
IO = 1.1 mA; VCC = 1.1 V
0.7 VCC
-
-
V
IO = 1.7 mA; VCC = 1.4 V
1.03
-
-
V
IO = 1.9 mA; VCC = 1.65 V
1.30
-
-
V
IO = 2.3 mA; VCC = 2.3 V
1.97
-
-
V
IO = 3.1 mA; VCC = 2.3 V
1.85
-
-
V
IO = 2.7 mA; VCC = 3.0 V
2.67
-
-
V
IO = 4.0 mA; VCC = 3.0 V
2.55
-
-
V
IO = 20 A; VCC = 0.8 V to 3.6 V
-
-
0.1
V
IO = 1.1 mA; VCC = 1.1 V
-
-
0.3 VCC
V
IO = 1.7 mA; VCC = 1.4 V
-
-
0.37
V
IO = 1.9 mA; VCC = 1.65 V
-
-
0.35
V
IO = 2.3 mA; VCC = 2.3 V
-
-
0.33
V
IO = 3.1 mA; VCC = 2.3 V
-
-
0.45
V
IO = 2.7 mA; VCC = 3.0 V
-
-
0.33
V
IO = 4.0 mA; VCC = 3.0 V
-
-
0.45
V
VI = VIH or VIL
II
input leakage current
VI = GND to 3.6 V; VCC = 0 V to 3.6 V
-
-
0.5
A
IOFF
power-off leakage current
VI or VO = 0 V to 3.6 V; VCC = 0 V
-
-
0.5
A
IOZ
OFF-state output current
VI = VIH or VIL; VO = 0 V to 3.6 V;
VCC = 0 V to 3.6 V
-
-
0.5
A
IOFF
additional power-off leakage VI or VO = 0 V to 3.6 V;
current
VCC = 0 V to 0.2 V
-
-
0.6
A
ICC
supply current
VI = GND or VCC; IO = 0 A;
VCC = 0.8 V to 3.6 V
-
-
0.9
A
ICC
additional supply current
data input; VI = VCC 0.6 V; IO = 0 A;
VCC = 3.3 V
[1]
-
-
50
A
1OE and 2OE input; VI = VCC 0.6 V;
IO = 0 A; VCC = 3.3 V
[1]
-
-
120
A
all inputs; VI = GND to 3.6 V;
1OE = VCC; 2OE = GND;
VCC = 0.8 V to 3.6 V
[2]
-
-
1
A
VCC = 0.8 V
0.75 VCC -
-
V
VCC = 0.9 V to 1.95 V
0.70 VCC -
-
V
VCC = 2.3 V to 2.7 V
1.6
-
-
V
VCC = 3.0 V to 3.6 V
2.0
-
-
V
Tamb = 40 C to +125 C
VIH
HIGH-level input voltage
74AUP2G241
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 11 February 2013
© NXP B.V. 2013. All rights reserved.
7 of 26
74AUP2G241
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
Table 7.
Static characteristics …continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Symbol Parameter
Conditions
Min
Typ
Max
VIL
VCC = 0.8 V
-
-
0.25 VCC V
VCC = 0.9 V to 1.95 V
-
-
0.30 VCC V
VCC = 2.3 V to 2.7 V
-
-
0.7
V
VCC = 3.0 V to 3.6 V
-
-
0.9
V
LOW-level input voltage
VOH
HIGH-level output voltage
LOW-level output voltage
VOL
Unit
VI = VIH or VIL
IO = 20 A; VCC = 0.8 V to 3.6 V
VCC 0.11 -
-
V
IO = 1.1 mA; VCC = 1.1 V
0.6 VCC
-
-
V
IO = 1.7 mA; VCC = 1.4 V
0.93
-
-
V
IO = 1.9 mA; VCC = 1.65 V
1.17
-
-
V
IO = 2.3 mA; VCC = 2.3 V
1.77
-
-
V
IO = 3.1 mA; VCC = 2.3 V
1.67
-
-
V
IO = 2.7 mA; VCC = 3.0 V
2.40
-
-
V
IO = 4.0 mA; VCC = 3.0 V
2.30
-
-
V
V
VI = VIH or VIL
IO = 20 A; VCC = 0.8 V to 3.6 V
-
-
0.11
IO = 1.1 mA; VCC = 1.1 V
-
-
0.33 VCC V
IO = 1.7 mA; VCC = 1.4 V
-
-
0.41
V
IO = 1.9 mA; VCC = 1.65 V
-
-
0.39
V
IO = 2.3 mA; VCC = 2.3 V
-
-
0.36
V
IO = 3.1 mA; VCC = 2.3 V
-
-
0.50
V
IO = 2.7 mA; VCC = 3.0 V
-
-
0.36
V
IO = 4.0 mA; VCC = 3.0 V
-
-
0.50
V
II
input leakage current
VI = GND to 3.6 V; VCC = 0 V to 3.6 V
-
-
0.75
A
IOZ
OFF-state output current
VI = VIH or VIL; VO = 0 V to 3.6 V;
VCC = 0 V to 3.6 V
-
-
0.75
A
IOFF
power-off leakage current
VI or VO = 0 V to 3.6 V; VCC = 0 V
-
-
0.75
A
IOFF
additional power-off leakage VI or VO = 0 V to 3.6 V;
current
VCC = 0 V to 0.2 V
-
-
0.75
A
ICC
supply current
VI = GND or VCC; IO = 0 A;
VCC = 0.8 V to 3.6 V
-
-
1.4
A
ICC
additional supply current
data input; VI = VCC 0.6 V; IO = 0 A;
VCC = 3.3 V
[1]
-
-
75
A
1OE and 2OE input; VI = VCC 0.6 V;
IO = 0 A; VCC = 3.3 V
[1]
-
-
180
A
all inputs; VI = GND to 3.6 V;
1OE = VCC; 2OE = GND;
VCC = 0.8 V to 3.6 V
[2]
-
-
1
A
[1]
One input at VCC 0.6 V, other input at VCC or GND.
[2]
To show ICC remains very low when the input-disable feature is enabled.
74AUP2G241
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 11 February 2013
© NXP B.V. 2013. All rights reserved.
8 of 26
74AUP2G241
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
11. Dynamic characteristics
Table 8.
Dynamic characteristics
Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 10.
Symbol Parameter
25 C
Conditions
40 C to +125 C
Unit
Min
Typ[1]
Max
Min
-
20.6
-
-
-
-
VCC = 1.1 V to 1.3 V
2.8
5.5
10.5
2.5
11.7
12.9
ns
VCC = 1.4 V to 1.6 V
2.2
3.9
6.1
2.0
7.3
8.1
ns
VCC = 1.65 V to 1.95 V
1.9
3.2
4.8
1.7
6.1
6.7
ns
VCC = 2.3 V to 2.7 V
1.6
2.6
3.6
1.4
4.3
4.9
ns
1.4
2.4
3.1
1.2
3.9
4.4
ns
-
69.9
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
3.1
6.1
11.8
2.9
13.9
15.4
ns
Max
Max
(85 C) (125 C)
CL = 5 pF
tpd
propagation delay nA to nY; see Figure 7
[2]
VCC = 0.8 V
VCC = 3.0 V to 3.6 V
ten
enable time
1OE to 1Y; see Figure 8
[3]
VCC = 0.8 V
VCC = 1.4 V to 1.6 V
2.5
4.2
6.6
2.3
7.7
8.3
ns
VCC = 1.65 V to 1.95 V
2.1
3.4
5.1
2.0
6.2
6.8
ns
VCC = 2.3 V to 2.7 V
1.8
2.6
3.7
1.7
4.5
5.0
ns
1.7
2.4
3.1
1.7
3.5
3.9
ns
-
71.6
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
2.8
6.2
12.4
2.6
13.6
13.6
ns
VCC = 1.4 V to 1.6 V
2.3
4.2
6.9
2.2
7.4
7.7
ns
VCC = 3.0 V to 3.6 V
2OE to 2Y; see Figure 9
[3]
VCC = 0.8 V
VCC = 1.65 V to 1.95 V
1.9
3.3
5.3
1.7
5.9
6.2
ns
VCC = 2.3 V to 2.7 V
1.5
2.4
3.6
1.4
3.8
4.1
ns
1.3
2.0
2.9
1.2
3.2
3.4
ns
VCC = 3.0 V to 3.6 V
tdis
disable time
1OE to 1Y; see Figure 8
[4]
VCC = 0.8 V
-
14.3
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
2.7
4.3
6.5
2.7
7.3
8.2
ns
VCC = 1.4 V to 1.6 V
2.1
3.2
4.4
2.1
5.1
5.7
ns
VCC = 1.65 V to 1.95 V
2.0
3.0
4.3
2.0
5.0
5.7
ns
VCC = 2.3 V to 2.7 V
1.4
2.2
2.9
1.4
3.3
4.1
ns
VCC = 3.0 V to 3.6 V
1.7
2.5
3.2
1.7
3.4
3.9
ns
-
10.3
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
2.6
4.2
6.2
2.9
6.4
6.5
ns
VCC = 1.4 V to 1.6 V
2.1
3.2
4.4
2.2
4.6
4.7
ns
VCC = 1.65 V to 1.95 V
2.1
3.1
4.4
1.7
4.6
4.8
ns
VCC = 2.3 V to 2.7 V
1.7
2.4
3.2
1.4
3.4
3.6
ns
VCC = 3.0 V to 3.6 V
2.1
2.8
3.6
1.2
3.7
3.8
ns
2OE to 2Y; see Figure 9
VCC = 0.8 V
74AUP2G241
Product data sheet
ns
[4]
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 11 February 2013
© NXP B.V. 2013. All rights reserved.
9 of 26
74AUP2G241
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
Table 8.
Dynamic characteristics …continued
Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 10.
Symbol Parameter
25 C
Conditions
40 C to +125 C
Unit
Min
Typ[1]
Max
Min
-
24.0
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
3.2
6.4
12.3
3.0
13.8
15.2
ns
VCC = 1.4 V to 1.6 V
2.1
4.5
7.3
1.9
8.5
9.4
ns
VCC = 1.65 V to 1.95 V
1.9
3.8
5.5
1.7
6.8
7.6
ns
VCC = 2.3 V to 2.7 V
2.1
3.2
4.2
1.6
5.3
5.9
ns
1.8
3.0
3.8
1.6
4.6
5.2
ns
-
73.7
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
3.6
6.9
13.5
3.4
15.8
17.5
ns
VCC = 1.4 V to 1.6 V
2.3
4.8
7.7
2.2
8.6
9.4
ns
Max
Max
(85 C) (125 C)
CL = 10 pF
tpd
propagation delay nA to nY; see Figure 7
[2]
VCC = 0.8 V
VCC = 3.0 V to 3.6 V
ten
enable time
1OE to 1Y; see Figure 8
[3]
VCC = 0.8 V
VCC = 1.65 V to 1.95 V
2.0
3.9
5.8
1.9
6.8
7.4
ns
VCC = 2.3 V to 2.7 V
1.8
3.2
4.3
1.7
5.3
5.9
ns
1.7
3.0
3.9
1.7
4.3
4.8
ns
VCC = 3.0 V to 3.6 V
2OE to 2Y; see Figure 9
[3]
VCC = 0.8 V
tdis
disable time
-
75.3
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
3.2
7.1
14.1
3.0
15.4
15.4
ns
VCC = 1.4 V to 1.6 V
2.2
4.8
8.0
2.1
8.3
8.6
ns
VCC = 1.65 V to 1.95 V
1.8
3.9
5.9
1.7
6.5
6.8
ns
VCC = 2.3 V to 2.7 V
1.5
2.9
4.2
1.4
4.5
4.8
ns
VCC = 3.0 V to 3.6 V
1.4
2.6
3.6
1.3
3.8
4.0
ns
-
32.7
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
3.4
5.4
7.9
3.4
8.8
9.9
ns
VCC = 1.4 V to 1.6 V
2.2
4.1
5.5
2.2
6.2
7.1
ns
VCC = 1.65 V to 1.95 V
2.2
4.2
5.6
1.9
6.3
7.1
ns
VCC = 2.3 V to 2.7 V
1.7
3.0
3.8
1.7
4.5
5.1
ns
2.1
3.8
4.8
1.7
5.0
5.6
ns
-
12.2
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
3.5
5.3
7.6
3.3
7.9
7.9
ns
VCC = 1.4 V to 1.6 V
2.2
4.1
5.6
2.1
5.7
5.9
ns
VCC = 1.65 V to 1.95 V
2.4
4.2
5.7
1.7
5.8
6.0
ns
VCC = 2.3 V to 2.7 V
1.9
3.2
4.1
1.4
4.3
4.5
ns
VCC = 3.0 V to 3.6 V
2.4
4.1
5.0
1.3
5.2
5.3
ns
1OE to 1Y; see Figure 8
[4]
VCC = 0.8 V
VCC = 3.0 V to 3.6 V
2OE to 2Y; see Figure 9
VCC = 0.8 V
74AUP2G241
Product data sheet
[4]
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 11 February 2013
© NXP B.V. 2013. All rights reserved.
10 of 26
74AUP2G241
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
Table 8.
Dynamic characteristics …continued
Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 10.
Symbol Parameter
25 C
Conditions
40 C to +125 C
Unit
Min
Typ[1]
Max
Min
-
27.4
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
3.6
7.2
14.1
3.3
15.8
17.5
ns
VCC = 1.4 V to 1.6 V
3.0
5.1
8.1
2.5
9.8
10.9
ns
VCC = 1.65 V to 1.95 V
2.2
4.3
6.3
2.0
7.9
8.8
ns
VCC = 2.3 V to 2.7 V
2.0
3.7
4.9
1.8
6.0
6.7
ns
2.0
3.5
4.4
1.8
5.4
6.1
ns
-
77.5
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
4.0
7.7
15.2
3.7
17.6
19.6
ns
VCC = 1.4 V to 1.6 V
3.0
5.3
8.4
2.5
9.8
10.7
ns
Max
Max
(85 C) (125 C)
CL = 15 pF
tpd
propagation delay nA to nY; see Figure 7
[2]
VCC = 0.8 V
VCC = 3.0 V to 3.6 V
ten
enable time
1OE to 1Y; see Figure 8
[3]
VCC = 0.8 V
VCC = 1.65 V to 1.95 V
2.3
4.4
6.5
2.1
7.7
8.5
ns
VCC = 2.3 V to 2.7 V
2.1
3.6
5.0
2.0
6.1
6.8
ns
2.0
3.5
4.5
1.9
4.9
5.5
ns
VCC = 3.0 V to 3.6 V
2OE to 2Y; see Figure 9
[3]
VCC = 0.8 V
tdis
disable time
-
79.2
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
3.6
7.8
15.8
3.3
17.1
17.1
ns
VCC = 1.4 V to 1.6 V
3.0
5.4
8.8
2.9
9.4
9.7
ns
VCC = 1.65 V to 1.95 V
2.1
4.3
6.7
2.0
7.3
7.7
ns
VCC = 2.3 V to 2.7 V
1.8
3.4
4.8
1.7
5.2
5.6
ns
VCC = 3.0 V to 3.6 V
1.6
3.1
4.3
1.5
4.5
4.7
ns
-
60.8
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
4.3
6.5
9.2
3.7
10.3
11.6
ns
VCC = 1.4 V to 1.6 V
3.0
5.0
6.5
2.5
7.4
8.4
ns
VCC = 1.65 V to 1.95 V
3.0
5.3
6.6
2.1
7.4
8.9
ns
VCC = 2.3 V to 2.7 V
2.1
3.8
4.9
2.0
5.1
6.4
ns
2.9
5.0
6.2
1.9
6.6
7.4
ns
-
14.9
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
4.3
6.4
8.5
3.7
9.3
9.4
ns
VCC = 1.4 V to 1.6 V
3.0
5.0
6.6
2.5
6.9
7.0
ns
VCC = 1.65 V to 1.95 V
3.1
5.4
6.6
2.0
7.4
7.5
ns
VCC = 2.3 V to 2.7 V
2.4
4.0
5.0
1.7
5.1
5.5
ns
VCC = 3.0 V to 3.6 V
3.2
5.3
6.2
1.5
6.7
6.9
ns
1OE to 1Y; see Figure 8
[4]
VCC = 0.8 V
VCC = 3.0 V to 3.6 V
2OE to 2Y; see Figure 9
VCC = 0.8 V
74AUP2G241
Product data sheet
[4]
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 11 February 2013
© NXP B.V. 2013. All rights reserved.
11 of 26
74AUP2G241
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
Table 8.
Dynamic characteristics …continued
Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 10.
Symbol Parameter
25 C
Conditions
40 C to +125 C
Unit
Min
Typ[1]
Max
Min
-
37.4
-
-
-
-
ns
4.8
9.5
19.0
4.4
21.6
24.0
ns
VCC = 1.4 V to 1.6 V
4.0
6.7
10.8
3.0
13.0
14.5
ns
VCC = 1.65 V to 1.95 V
2.9
5.6
8.4
2.6
10.3
11.5
ns
VCC = 2.3 V to 2.7 V
2.7
4.8
6.3
2.5
7.8
8.7
ns
2.7
4.6
5.8
2.5
7.0
8.3
ns
-
88.9
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
5.2
9.9
19.8
4.8
22.8
25.3
ns
VCC = 1.4 V to 1.6 V
4.0
6.8
10.8
3.1
12.6
14.1
ns
VCC = 1.65 V to 1.95 V
3.0
5.6
8.5
2.8
10.2
11.3
ns
VCC = 2.3 V to 2.7 V
2.7
4.8
6.5
2.6
7.8
8.8
ns
2.7
4.6
6.0
2.6
6.9
7.7
ns
Max
Max
(85 C) (125 C)
CL = 30 pF
tpd
propagation delay nA to nY; see Figure 7
[2]
VCC = 0.8 V
VCC = 1.1 V to 1.3 V
VCC = 3.0 V to 3.6 V
ten
enable time
1OE to 1Y; see Figure 8
[3]
VCC = 0.8 V
VCC = 3.0 V to 3.6 V
2OE to 2Y; see Figure 9
[3]
VCC = 0.8 V
tdis
disable time
-
90.6
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
4.7
10.0
20.4
4.3
22.0
22.0
ns
VCC = 1.4 V to 1.6 V
3.0
6.9
11.3
3.7
12.0
12.5
ns
VCC = 1.65 V to 1.95 V
2.6
5.6
8.6
3.2
9.5
10.1
ns
VCC = 2.3 V to 2.7 V
2.3
4.5
6.3
2.9
6.8
7.3
ns
VCC = 3.0 V to 3.6 V
2.2
4.2
5.8
2.7
6.4
6.7
ns
-
49.9
-
-
-
-
ns
1OE to 1Y; see Figure 8
[4]
VCC = 0.8 V
VCC = 1.1 V to 1.3 V
6.0
9.9
13.3
4.8
14.8
16.5
ns
VCC = 1.4 V to 1.6 V
4.4
7.7
9.6
3.1
10.7
12.1
ns
VCC = 1.65 V to 1.95 V
5.1
8.7
11.1
2.8
12.4
13.8
ns
VCC = 2.3 V to 2.7 V
3.6
6.2
7.4
2.6
8.6
9.6
ns
5.2
8.7
10.5
2.6
10.8
13.1
ns
-
51.6
-
-
-
-
ns
6.0
9.8
13.6
4.7
14.3
14.4
ns
VCC = 3.0 V to 3.6 V
2OE to 2Y; see Figure 9
VCC = 0.8 V
VCC = 1.1 V to 1.3 V
74AUP2G241
Product data sheet
[4]
VCC = 1.4 V to 1.6 V
4.5
7.7
10.5
3.0
10.7
11.0
ns
VCC = 1.65 V to 1.95 V
5.2
8.8
11.4
2.6
11.5
11.6
ns
VCC = 2.3 V to 2.7 V
3.9
6.4
7.4
2.3
9.0
10.2
ns
VCC = 3.0 V to 3.6 V
5.5
9.0
10.7
2.2
10.8
12.0
ns
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 11 February 2013
© NXP B.V. 2013. All rights reserved.
12 of 26
74AUP2G241
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
Table 8.
Dynamic characteristics …continued
Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 10.
Symbol Parameter
25 C
Conditions
40 C to +125 C
Unit
Min
Typ[1]
Max
Min
VCC = 0.8 V
-
2.8
-
-
-
-
pF
VCC = 1.1 V to 1.3 V
-
2.8
-
-
-
-
pF
Max
Max
(85 C) (125 C)
CL = 5 pF, 10 pF, 15 pF and 30 pF
power dissipation
capacitance
CPD
f = 1 MHz; VI = GND to VCC
VCC = 1.4 V to 1.6 V
-
3.0
-
-
-
-
pF
VCC = 1.65 V to 1.95 V
-
3.0
-
-
-
-
pF
VCC = 2.3 V to 2.7 V
-
3.7
-
-
-
-
pF
VCC = 3.0 V to 3.6 V
-
4.2
-
-
-
-
pF
[1]
All typical values are measured at nominal VCC.
[2]
tpd is the same as tPLH and tPHL.
[3]
ten is the same as tPZH and tPZL.
[4]
tdis is the same as tPHZ and tPLZ.
[5]
[5]
CPD is used to determine the dynamic power dissipation (PD in W).
PD = CPD VCC2 fi N + (CL VCC2 fo) where:
fi = input frequency in MHz;
fo = output frequency in MHz;
CL = output load capacitance in pF;
VCC = supply voltage in V;
N = number of inputs switching;
(CL VCC2 fo) = sum of the outputs.
12. Waveforms
VI
VM
nA input
GND
tPHL
tPLH
VOH
VM
nY output
VOL
mna230
Measurement points are given in Table 9.
Logic levels: VOL and VOH are typical output voltage levels that occur with the output load.
Fig 7.
Table 9.
The data input (nA) to output (nY) propagation delays
Measurement points
Supply voltage
Output
Input
VCC
VM
VM
VI
tr = tf
0.8 V to 3.6 V
0.5 VCC
0.5 VCC
VCC
3.0 ns
74AUP2G241
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 11 February 2013
© NXP B.V. 2013. All rights reserved.
13 of 26
74AUP2G241
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
VI
1OE input
VM
GND
tPLZ
tPZL
VCC
output
LOW-to-OFF
OFF-to-LOW
VM
VOL + 0.3 V
VOL
tPHZ
tPZH
VOH
VOH − 0.3 V
output
HIGH-to-OFF
OFF-to-HIGH
VM
GND
outputs
enabled
outputs
enabled
outputs
disabled
001aaa411
Measurement points are given in Table 10.
Logic levels: VOL and VOH are typical output voltage levels that occur with the output load.
Fig 8.
3-state enable and disable times
VI
2OE input
VM
GND
tPLZ
tPZL
VCC
output
LOW-to-OFF
OFF-to-LOW
VM
VOL + 0.3 V
VOL
tPHZ
VOH
tPZH
VOH − 0.3 V
output
HIGH-to-OFF
OFF-to-HIGH
VM
GND
outputs
enabled
outputs
enabled
outputs
disabled
001aaa410
Measurement points are given in Table 10.
Logic levels: VOL and VOH are typical output voltage levels that occur with the output load.
Fig 9.
Table 10.
3-state enable and disable times
Measurement points
Supply voltage
Input
Output
VCC
VM
VM
VX
0.8 V to 1.6 V
0.5 VCC
0.5 VCC
VOL 0.1 V
VOH 0.1 V
1.65 V to 2.7 V
0.5 VCC
0.5 VCC
VOL 0.15 V
VOH 0.15 V
3.0 V to 3.6 V
0.5 VCC
0.5 VCC
VOL 0.3 V
VOH 0.3 V
74AUP2G241
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 11 February 2013
VY
© NXP B.V. 2013. All rights reserved.
14 of 26
74AUP2G241
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
VCC
VEXT
5 kΩ
G
VI
VO
DUT
CL
RT
RL
001aac521
Test data is given in Table 11.
Definitions for test circuit:
RL = Load resistance.
CL = Load capacitance including jig and probe capacitance.
RT = Termination resistance should be equal to the output impedance Zo of the pulse generator.
VEXT = External voltage for measuring switching times.
Fig 10. Test circuit for measuring switching times
Table 11.
Test data
Supply voltage
Load
VEXT
[1]
VCC
CL
RL
0.8 V to 3.6 V
5 pF, 10 pF, 15 pF and 30 pF
5 k or 1 M
[1]
tPLH, tPHL
tPZH, tPHZ
tPZL, tPLZ
open
GND
2 VCC
For measuring enable and disable times RL = 5 k, for measuring propagation delays, setup and hold times and pulse width RL = 1 M.
74AUP2G241
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 11 February 2013
© NXP B.V. 2013. All rights reserved.
15 of 26
74AUP2G241
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
13. Package outline
VSSOP8: plastic very thin shrink small outline package; 8 leads; body width 2.3 mm
D
E
SOT765-1
A
X
c
y
HE
v M A
Z
5
8
Q
A
A2
A1
pin 1 index
(A3)
θ
Lp
1
4
e
L
detail X
w M
bp
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D(1)
E(2)
e
HE
L
Lp
Q
v
w
y
Z(1)
θ
mm
1
0.15
0.00
0.85
0.60
0.12
0.27
0.17
0.23
0.08
2.1
1.9
2.4
2.2
0.5
3.2
3.0
0.4
0.40
0.15
0.21
0.19
0.2
0.13
0.1
0.4
0.1
8°
0°
Notes
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
2. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
OUTLINE
VERSION
SOT765-1
REFERENCES
IEC
JEDEC
JEITA
EUROPEAN
PROJECTION
ISSUE DATE
02-06-07
MO-187
Fig 11. Package outline SOT765-1 (VSSOP8)
74AUP2G241
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 11 February 2013
© NXP B.V. 2013. All rights reserved.
16 of 26
74AUP2G241
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
XSON8: plastic extremely thin small outline package; no leads; 8 terminals; body 1 x 1.95 x 0.5 mm
1
2
SOT833-1
b
4
3
4×
(2)
L
L1
e
8
7
6
e1
5
e1
e1
8×
A
(2)
A1
D
E
terminal 1
index area
0
1
2 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A(1)
max
A1
max
b
D
E
e
e1
L
L1
mm
0.5
0.04
0.25
0.17
2.0
1.9
1.05
0.95
0.6
0.5
0.35
0.27
0.40
0.32
Notes
1. Including plating thickness.
2. Can be visible in some manufacturing processes.
REFERENCES
OUTLINE
VERSION
IEC
JEDEC
JEITA
SOT833-1
---
MO-252
---
EUROPEAN
PROJECTION
ISSUE DATE
07-11-14
07-12-07
Fig 12. Package outline SOT833-1 (XSON8)
74AUP2G241
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 11 February 2013
© NXP B.V. 2013. All rights reserved.
17 of 26
74AUP2G241
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
XSON8: extremely thin small outline package; no leads;
8 terminals; body 1.35 x 1 x 0.5 mm
SOT1089
E
terminal 1
index area
D
A
A1
detail X
(4×)(2)
e
L
(8×)(2)
b 4
5
e1
1
terminal 1
index area
8
L1
X
0
0.5
scale
Dimensions
Unit
mm
max
nom
min
1 mm
A(1)
0.5
A1
b
D
E
e
e1
L
L1
0.35 0.40
0.04 0.20 1.40 1.05
0.15 1.35 1.00 0.55 0.35 0.30 0.35
0.27 0.32
0.12 1.30 0.95
Note
1. Including plating thickness.
2. Visible depending upon used manufacturing technology.
Outline
version
SOT1089
sot1089_po
References
IEC
JEDEC
JEITA
European
projection
Issue date
10-04-09
10-04-12
MO-252
Fig 13. Package outline SOT1089 (XSON8)
74AUP2G241
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 11 February 2013
© NXP B.V. 2013. All rights reserved.
18 of 26
74AUP2G241
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
XSON8: plastic extremely thin small outline package; no leads;
8 terminals; body 3 x 2 x 0.5 mm
B
D
SOT996-2
A
E
A
A1
detail X
terminal 1
index area
e1
1
4
8
5
C
C A B
C
v
w
b
e
L1
y
y1 C
L2
L
X
0
1
2 mm
scale
Dimensions (mm are the original dimensions)
Unit(1)
mm
max
nom
min
A
A1
b
0.05 0.35
D
E
2.1
3.1
0.5
0.00 0.15
1.9
e
e1
0.5
1.5
2.9
L
L1
L2
0.5
0.15
0.6
0.3
0.05
0.4
v
0.1
w
y
0.05 0.05
y1
0.1
sot996-2_po
Outline
version
References
IEC
JEDEC
JEITA
European
projection
Issue date
07-12-21
12-11-20
SOT996-2
Fig 14. Package outline SOT996-2 (XSON8)
74AUP2G241
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 11 February 2013
© NXP B.V. 2013. All rights reserved.
19 of 26
74AUP2G241
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
XQFN8: plastic, extremely thin quad flat package; no leads;
8 terminals; body 1.6 x 1.6 x 0.5 mm
SOT902-2
X
A
B
D
terminal 1
index area
E
A
A1
detail X
e
v
w
b
4
3
C
C A B
C
y
y1 C
5
e1
2
6
1
7
terminal 1
index area
8
L
metal area
not for soldering
L1
0
1
Dimensions
Unit(1)
mm
max
nom
min
2 mm
scale
A
0.5
A1
b
D
E
e
e1
0.05 0.25 1.65 1.65
0.20 1.60 1.60 0.55
0.00 0.15 1.55 1.55
0.5
L
L1
v
0.35 0.15
0.30 0.10
0.25 0.05
0.1
w
y
y1
0.05 0.05 0.05
Note
1. Plastic or metal protrusions of 0.075 mm maximum per side are not included.
References
Outline
version
IEC
JEDEC
JEITA
SOT902-2
---
MO-255
---
sot902-2_po
European
projection
Issue date
10-11-02
11-03-31
Fig 15. Package outline SOT902-2 (XQFN8)
74AUP2G241
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 11 February 2013
© NXP B.V. 2013. All rights reserved.
20 of 26
74AUP2G241
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
XSON8: extremely thin small outline package; no leads;
8 terminals; body 1.2 x 1.0 x 0.35 mm
1
2
SOT1116
b
4
3
(4×)(2)
L
L1
e
8
7
e1
6
e1
5
e1
(8×)(2)
A1
A
D
E
terminal 1
index area
0
0.5
scale
Dimensions
Unit
mm
1 mm
A(1)
A1
b
D
E
e
e1
max 0.35 0.04 0.20 1.25 1.05
nom
0.15 1.20 1.00 0.55
min
0.12 1.15 0.95
0.3
L
L1
0.35 0.40
0.30 0.35
0.27 0.32
Note
1. Including plating thickness.
2. Visible depending upon used manufacturing technology.
Outline
version
sot1116_po
References
IEC
JEDEC
JEITA
European
projection
Issue date
10-04-02
10-04-07
SOT1116
Fig 16. Package outline SOT1116 (XSON8)
74AUP2G241
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 11 February 2013
© NXP B.V. 2013. All rights reserved.
21 of 26
74AUP2G241
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
XSON8: extremely thin small outline package; no leads;
8 terminals; body 1.35 x 1.0 x 0.35 mm
SOT1203
b
2
1
3
(4×)(2)
4
L
L1
e
8
7
6
e1
e1
5
e1
(8×)(2)
A1
A
D
E
terminal 1
index area
0
0.5
scale
Dimensions
Unit
mm
1 mm
A(1)
A1
b
D
E
e
e1
L
L1
max 0.35 0.04 0.20 1.40 1.05
0.35 0.40
nom
0.15 1.35 1.00 0.55 0.35 0.30 0.35
min
0.12 1.30 0.95
0.27 0.32
Note
1. Including plating thickness.
2. Visible depending upon used manufacturing technology.
Outline
version
sot1203_po
References
IEC
JEDEC
JEITA
European
projection
Issue date
10-04-02
10-04-06
SOT1203
Fig 17. Package outline SOT1203 (XSON8)
74AUP2G241
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 11 February 2013
© NXP B.V. 2013. All rights reserved.
22 of 26
74AUP2G241
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
14. Abbreviations
Table 12.
Abbreviations
Acronym
Description
CDM
Charged Device Model
DUT
Device Under Test
ESD
ElectroStatic Discharge
HBM
Human Body Model
MM
Machine Model
15. Revision history
Table 13.
Revision history
Document ID
Release date
Data sheet status
Change notice
Supersedes
74AUP2G241 v.7
20130211
Product data sheet
-
74AUP2G241 v.6
Modifications:
•
For type number 74AUP2G241GD XSON8U has changed to XSON8.
74AUP2G241 v.6
20120606
Product data sheet
-
74AUP2G241 v.5
74AUP2G241 v.5
20111205
Product data sheet
-
74AUP2G241 v.4
74AUP2G241 v.4
20100913
Product data sheet
-
74AUP2G241 v.3
74AUP2G241 v.3
20090112
Product data sheet
-
74AUP2G241 v.2
74AUP2G241 v.2
20080219
Product data sheet
-
74AUP2G241 v.1
74AUP2G241 v.1
20061012
Product data sheet
-
-
74AUP2G241
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 11 February 2013
© NXP B.V. 2013. All rights reserved.
23 of 26
74AUP2G241
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
16. Legal information
16.1 Data sheet status
Document status[1][2]
Product status[3]
Definition
Objective [short] data sheet
Development
This document contains data from the objective specification for product development.
Preliminary [short] data sheet
Qualification
This document contains data from the preliminary specification.
Product [short] data sheet
Production
This document contains the product specification.
[1]
Please consult the most recently issued document before initiating or completing a design.
[2]
The term ‘short data sheet’ is explained in section “Definitions”.
[3]
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
16.2 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
NXP Semiconductors and its customer, unless NXP Semiconductors and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the NXP Semiconductors product is
deemed to offer functions and qualities beyond those described in the
Product data sheet.
16.3 Disclaimers
Limited warranty and liability — Information in this document is believed to
be accurate and reliable. However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information. NXP Semiconductors takes no
responsibility for the content in this document if provided by an information
source outside of NXP Semiconductors.
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of NXP Semiconductors.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
74AUP2G241
Product data sheet
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in life support, life-critical or
safety-critical systems or equipment, nor in applications where failure or
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors and its suppliers accept no liability for
inclusion and/or use of NXP Semiconductors products in such equipment or
applications and therefore such inclusion and/or use is at the customer’s own
risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Customers are responsible for the design and operation of their applications
and products using NXP Semiconductors products, and NXP Semiconductors
accepts no liability for any assistance with applications or customer product
design. It is customer’s sole responsibility to determine whether the NXP
Semiconductors product is suitable and fit for the customer’s applications and
products planned, as well as for the planned application and use of
customer’s third party customer(s). Customers should provide appropriate
design and operating safeguards to minimize the risks associated with their
applications and products.
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default in the
customer’s applications or products, or the application or use by customer’s
third party customer(s). Customer is responsible for doing all necessary
testing for the customer’s applications and products using NXP
Semiconductors products in order to avoid a default of the applications and
the products or of the application or use by customer’s third party
customer(s). NXP does not accept any liability in this respect.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
Terms and conditions of commercial sale — NXP Semiconductors
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. NXP Semiconductors hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 11 February 2013
© NXP B.V. 2013. All rights reserved.
24 of 26
74AUP2G241
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from competent authorities.
Non-automotive qualified products — Unless this data sheet expressly
states that this specific NXP Semiconductors product is automotive qualified,
the product is not suitable for automotive use. It is neither qualified nor tested
in accordance with automotive testing or application requirements. NXP
Semiconductors accepts no liability for inclusion and/or use of
non-automotive qualified products in automotive equipment or applications.
In the event that customer uses the product for design-in and use in
automotive applications to automotive specifications and standards, customer
(a) shall use the product without NXP Semiconductors’ warranty of the
product for such automotive applications, use and specifications, and (b)
whenever customer uses the product for automotive applications beyond
NXP Semiconductors’ specifications such use shall be solely at customer’s
own risk, and (c) customer fully indemnifies NXP Semiconductors for any
liability, damages or failed product claims resulting from customer design and
use of the product for automotive applications beyond NXP Semiconductors’
standard warranty and NXP Semiconductors’ product specifications.
Translations — A non-English (translated) version of a document is for
reference only. The English version shall prevail in case of any discrepancy
between the translated and English versions.
16.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
17. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
74AUP2G241
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 7 — 11 February 2013
© NXP B.V. 2013. All rights reserved.
25 of 26
74AUP2G241
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
18. Contents
1
2
3
4
5
6
6.1
6.2
7
8
9
10
11
12
13
14
15
16
16.1
16.2
16.3
16.4
17
18
General description . . . . . . . . . . . . . . . . . . . . . . 1
Features and benefits . . . . . . . . . . . . . . . . . . . . 1
Ordering information . . . . . . . . . . . . . . . . . . . . . 2
Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Functional diagram . . . . . . . . . . . . . . . . . . . . . . 3
Pinning information . . . . . . . . . . . . . . . . . . . . . . 3
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4
Functional description . . . . . . . . . . . . . . . . . . . 4
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 5
Recommended operating conditions. . . . . . . . 5
Static characteristics. . . . . . . . . . . . . . . . . . . . . 5
Dynamic characteristics . . . . . . . . . . . . . . . . . . 9
Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 16
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Revision history . . . . . . . . . . . . . . . . . . . . . . . . 23
Legal information. . . . . . . . . . . . . . . . . . . . . . . 24
Data sheet status . . . . . . . . . . . . . . . . . . . . . . 24
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Contact information. . . . . . . . . . . . . . . . . . . . . 25
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2013.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
Date of release: 11 February 2013
Document identifier: 74AUP2G241