BSC9131NXN1KHKB

QorIQ Qonverge Platform QorIQ Qonverge BSC9131 for Femtocell Base Station Solutions A new dimension in wireless processing Target Applications Overview cost-effective, integrated solution that handles Femtocell: Home or small office cellular The QorIQ Qonverge BSC9131 processor is all the digital baseband processing required for base stations supporting the following standards: • LTE-FDD/TDD • WCDMA (HSPA+) • CDMA2K a highly integrated device that targets evolving femtocells. femto and enterprise femto applications. The The programmable BSC9131 device, targeted at BSC9131 combines Power Architecture® e500 LTE/FDD/TDD, WCDMA (HSPA+) and CDMA2K, and StarCore SC3850 core technologies with supports multiple air interface standards and can MAPLE-B2F baseband acceleration processing, support two concurrent standards. addressing the need for a high-performance, • TD-SCDMA QorIQ Qonverge BSC9130 and BSC9131 Processors QorIQ Qonverge BSC9131 Processor StarCore SC3850 DSP Core 32 KB L1 I-Cache 32 KB L1 D-Cache 512 KB L2 Cache e500 Core Built on Power Architecture® 32 KB I-Cache 32 KB D-Cache Coherency Module 256 KB L2 Cache 32-bit DDR3/3L Memory Controller MAPLE-B2F Baseband Accelerator LTE/UMTS/CDMA2K RF Interface (JESD207/ADI) and MaxPHY Multicore Fabric 4x eSPI 2x DUART Ethernet 2x I2C GPIO USIM IFC eSDHC 2x PWM Clocks/Reset DMA Security Engine V4.4 USB 2.0 IEEE® 1588 1x GE 1x GE  QorIQ Qonverge Features The BSC9131 is a highly integrated device combining Power, StarCore and MAPLE architectures. The device includes the following features: Core • Power Architecture® subsystem including one e500 processor and 256 KB shared L2 cache DSP • StarCore SC3850 DSP subsystem including 512 KB private L2 cache Baseband Acceleration • MAPLE-B2F multi-accelerator platform engine supports functions that enable LTE-FDD/TDD, WCDMA (HSPA+) and CDMA2K wireless standards Memory • DDR3 memory interface with 32-bit data width (40 bits including ECC), up to 800 MHz data rate Security • Dedicated security engine featuring trusted boot RF Interface • Antenna interface controller supporting three industry standard JESD207/three custom ADI RF interfaces (two dual port and one single port) • Integrated flash controller for NOR, NAND and FPGA support • Two pulse width modulators (PWM) for control of external components • Three MAXIMs MaxPhy serial interfaces Connectivity • Two triple-speed Gigabit-Ethernet controllers featuring network acceleration including IEEE® Std 1588v2™ hardware support • USB 2.0 host and device controller • DMA controller with four bidirectional channels that serves both Power Architecture cores and DSP domains • UART, SPI, eSDHC, USIM and I2C controllers • GPIO, 16 32-bit timers Freescale will provide commercial L1 and transport software. L2, L3 will be provided through our partner stack vendors: • LTE-FDD/TDD and WCDMA (HSPA+) L1 software–licensed by Freescale • L2/L3 software for LTE-FDD/TDD and WCDMA (HSPA+)–via partners • Development tools and operating system software through Freescale and its ecosystem partners BSC9131 Reference Design Board For more information about the QorIQ Qonverge BSC913x family, visit freescale.com/QorIQQonverge Freescale, the Freescale logo, QorIQ and StarCore are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. QorIQ Qonverge is a trademark of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. The Power Architecture and Power.org word marks and the Power and Power.org logos and related marks are trademarks and service marks licensed by Power.org. © 2012 Freescale Semiconductor, Inc. Document Number: QORIQPSC9131FS REV 2