LPC2142

LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers; up to 512 kB flash with ISP/IAP, USB 2.0 full-speed device, 10-bit ADC and DAC Rev. 03 — 19 October 2007 Product data sheet 1. General description The LPC2141/42/44/46/48 microcontrollers are based on a 16-bit/32-bit ARM7TDMI-S CPU with real-time emulation and embedded trace support, that combine microcontrollers with embedded high-speed flash memory ranging from 32 kB to 512 kB. A 128-bit wide memory interface and a unique accelerator architecture enable 32-bit code execution at the maximum clock rate. For critical code size applications, the alternative 16-bit Thumb mode reduces code by more than 30 % with minimal performance penalty. Due to their tiny size and low power consumption, LPC2141/42/44/46/48 are ideal for applications where miniaturization is a key requirement, such as access control and point-of-sale. Serial communications interfaces ranging from a USB 2.0 Full-speed device, multiple UARTs, SPI, SSP to I2C-bus and on-chip SRAM of 8 kB up to 40 kB, make these devices very well suited for communication gateways and protocol converters, soft modems, voice recognition and low end imaging, providing both large buffer size and high processing power. Various 32-bit timers, single or dual 10-bit ADCs, 10-bit DAC, PWM channels and 45 fast GPIO lines with up to nine edge or level sensitive external interrupt pins make these microcontrollers suitable for industrial control and medical systems. 2. Features 2.1 Key features I 16-bit/32-bit ARM7TDMI-S microcontroller in a tiny LQFP64 package I 8 kB to 40 kB of on-chip static RAM and 32 kB to 512 kB of on-chip flash memory; 128-bit wide interface/accelerator enables high-speed 60 MHz operation I In-System Programming/In-Application Programming (ISP/IAP) via on-chip boot loader software, single flash sector or full chip erase in 400 ms and programming of 256 B in 1 ms I EmbeddedICE RT and Embedded Trace interfaces offer real-time debugging with the on-chip RealMonitor software and high-speed tracing of instruction execution I USB 2.0 Full-speed compliant device controller with 2 kB of endpoint RAM In addition, the LPC2146/48 provides 8 kB of on-chip RAM accessible to USB by DMA I One or two (LPC2141/42 vs, LPC2144/46/48) 10-bit ADCs provide a total of 6/14 analog inputs, with conversion times as low as 2.44 µs per channel I Single 10-bit DAC provides variable analog output (LPC2142/44/46/48 only) I Two 32-bit timers/external event counters (with four capture and four compare channels each), PWM unit (six outputs) and watchdog NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers I Low power Real-Time Clock (RTC) with independent power and 32 kHz clock input I Multiple serial interfaces including two UARTs (16C550), two Fast I2C-bus (400 kbit/s), SPI and SSP with buffering and variable data length capabilities I Vectored Interrupt Controller (VIC) with configurable priorities and vector addresses I Up to 45 of 5 V tolerant fast general purpose I/O pins in a tiny LQFP64 package I Up to 21 external interrupt pins available I 60 MHz maximum CPU clock available from programmable on-chip PLL with settling time of 100 µs I On-chip integrated oscillator operates with an external crystal from 1 MHz to 25 MHz I Power saving modes include Idle and Power-down I Individual enable/disable of peripheral functions as well as peripheral clock scaling for additional power optimization I Processor wake-up from Power-down mode via external interrupt or BOD I Single power supply chip with POR and BOD circuits: N CPU operating voltage range of 3.0 V to 3.6 V (3.3 V ± 10 %) with 5 V tolerant I/O pads 3. Ordering information Table 1. Ordering information Package Name LPC2141FBD64 LPC2142FBD64 LPC2144FBD64 LPC2146FBD64 LPC2148FBD64 LQFP64 Description plastic low profile quad flat package; 64 leads; body 10 × 10 × 1.4 mm Version SOT314-2 Type number 3.1 Ordering options Table 2. Ordering options Flash RAM memory 8 kB 16 kB 16 kB Endpoint USB RAM 2 kB 2 kB 2 kB ADC (channels overall) 1 (6 channels) 1 (6 channels) 2 (14 channels) 2 (14 channels) DAC 1 1 1 Temperature range (°C) −40 to +85 −40 to +85 −40 to +85 −40 to +85 Type number LPC2141FBD64 32 kB LPC2142FBD64 64 kB LPC2144FBD64 128 kB LPC2146FBD64 256 kB 32 kB + 8 kB 2 kB shared with USB DMA[1] 32 kB + 8 kB 2 kB shared with USB DMA[1] LPC2148FBD64 512 kB 2 (14 channels) 1 −40 to +85 [1] While the USB DMA is the primary user of the additional 8 kB RAM, this RAM is also accessible at any time by the CPU as a general purpose RAM for data and code storage. LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 2 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers 4. Block diagram TMS(1) TDI(1) TRST(1) TCK(1) TDO(1) XTAL2 RST XTAL1 EMULATION TRACE MODULE LPC2141/42/44/46/48 P0[31:28] and P0[25:0] P1[31:16] TEST/DEBUG INTERFACE PLL0 system clock PLL1 USB clock VECTORED INTERRUPT CONTROLLER SYSTEM FUNCTIONS FAST GENERAL PURPOSE I/O ARM7TDMI-S AHB BRIDGE ARM7 local bus AMBA AHB (Advanced High-performance Bus) INTERNAL SRAM CONTROLLER INTERNAL FLASH CONTROLLER 8 kB RAM SHARED WITH USB DMA(3) AHB DECODER 8 kB/16 kB/ 32 kB SRAM 32 kB/64 kB/128 kB/ 256 kB/512 kB FLASH AHB TO VPB BRIDGE VPB DIVIDER VPB (VLSI peripheral bus) EINT3 to EINT0 EXTERNAL INTERRUPTS USB 2.0 FULL-SPEED DEVICE CONTROLLER WITH DMA(3) D+ D− UP_LED CONNECT VBUS SCL0, SCL1 4 × CAP0 4 × CAP1 8 × MAT0 8 × MAT1 AD0[7:6] and AD0[4:1] AD1[7:0](2) CAPTURE/COMPARE (W/EXTERNAL CLOCK) TIMER 0/TIMER 1 I2C-BUS SERIAL INTERFACES 0 AND 1 SDA0, SDA1 SCK0, SCK1 ADC0 AND ADC1(2) SPI AND SSP SERIAL INTERFACES MOSI0, MOSI1 MISO0, MISO1 SSEL0, SSEL1 TXD0, TXD1 AOUT(4) DAC UART0/UART1 RXD0, RXD1 P0[31:28] and P0[25:0] P1[31:16] GENERAL PURPOSE I/O REAL-TIME CLOCK DSR1(2),CTS1(2), RTS1(2), DTR1(2) DCD1(2),RI1(2) RTCX1 RTCX2 VBAT PWM6 to PWM0 PWM0 WATCHDOG TIMER SYSTEM CONTROL 002aab560 (1) Pins shared with GPIO. (2) LPC2144/46/48 only. (3) USB DMA controller with 8 kB of RAM accessible as general purpose RAM and/or DMA is available in LPC2146/48 only. (4) LPC2142/44/46/48 only. Fig 1. Block diagram LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 3 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers 5. Pinning information 5.1 Pinning 54 P0.19/MAT1.2/MOSI1/CAP1.2 53 P0.18/CAP1.3/MISO1/MAT1.3 55 P0.20/MAT1.3/SSEL1/EINT3 58 P0.23/VBUS 52 P1.30/TMS 64 P1.27/TDO 56 P1.29/TCK 60 P1.28/TDI 57 RESET 62 XTAL1 61 XTAL2 63 VREF P0.21/PWM5/CAP1.3 P0.22/CAP0.0/MAT0.0 RTCX1 P1.19/TRACEPKT3 RTCX2 VSS VDDA P1.18/TRACEPKT2 P0.25/AD0.4 1 2 3 4 5 6 7 8 9 49 VBAT 59 VSSA 51 VDD 50 VSS 48 P1.20/TRACESYNC 47 P0.17/CAP1.2/SCK1/MAT1.2 46 P0.16/EINT0/MAT0.2/CAP0.2 45 P0.15/EINT2 44 P1.21/PIPESTAT0 43 VDD 42 VSS 41 P0.14/EINT1/SDA1 40 P1.22/PIPESTAT1 39 P0.13/MAT1.1 38 P0.12/MAT1.0 37 P0.11/CAP1.1/SCL1 36 P1.23/PIPESTAT2 35 P0.10/CAP1.0 34 P0.9/RXD1/PWM6/EINT3 33 P0.8/TXD1/PWM4 LPC2141 D+ 10 D− 11 P1.17/TRACEPKT1 12 P0.28/AD0.1/CAP0.2/MAT0.2 13 P0.29/AD0.2/CAP0.3/MAT0.3 14 P0.30/AD0.3/EINT3/CAP0.0 15 P1.16/TRACEPKT0 16 P0.31/UP_LED/CONNECT 17 VSS 18 P0.0/TXD0/PWM1 19 P1.31/TRST 20 P0.1/RXD0/PWM3/EINT0 21 P0.2/SCL0/CAP0.0 22 VDD 23 P1.26/RTCK 24 VSS 25 P0.3/SDA0/MAT0.0/EINT1 26 P0.4/SCK0/CAP0.1/AD0.6 27 P1.25/EXTIN0 28 P0.5/MISO0/MAT0.1/AD0.7 29 P0.6/MOSI0/CAP0.2 30 P0.7/SSEL0/PWM2/EINT2 31 P1.24/TRACECLK 32 002aab733 Fig 2. LPC2141 pinning LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 4 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers 54 P0.19/MAT1.2/MOSI1/CAP1.2 53 P0.18/CAP1.3/MISO1/MAT1.3 55 P0.20/MAT1.3/SSEL1/EINT3 58 P0.23/VBUS 52 P1.30/TMS 64 P1.27/TDO 56 P1.29/TCK 60 P1.28/TDI 57 RESET 62 XTAL1 61 XTAL2 63 VREF P0.21/PWM5/CAP1.3 P0.22/CAP0.0/MAT0.0 RTCX1 P1.19/TRACEPKT3 RTCX2 VSS VDDA P1.18/TRACEPKT2 P0.25/AD0.4/AOUT 1 2 3 4 5 6 7 8 9 49 VBAT 59 VSSA 51 VDD 50 VSS 48 P1.20/TRACESYNC 47 P0.17/CAP1.2/SCK1/MAT1.2 46 P0.16/EINT0/MAT0.2/CAP0.2 45 P0.15/EINT2 44 P1.21/PIPESTAT0 43 VDD 42 VSS 41 P0.14/EINT1/SDA1 40 P1.22/PIPESTAT1 39 P0.13/MAT1.1 38 P0.12/MAT1.0 37 P0.11/CAP1.1/SCL1 36 P1.23/PIPESTAT2 35 P0.10/CAP1.0 34 P0.9/RXD1/PWM6/EINT3 33 P0.8/TXD1/PWM4 LPC2142 D+ 10 D− 11 P1.17/TRACEPKT1 12 P0.28/AD0.1/CAP0.2/MAT0.2 13 P0.29/AD0.2/CAP0.3/MAT0.3 14 P0.30/AD0.3/EINT3/CAP0.0 15 P1.16/TRACEPKT0 16 P0.31/UP_LED/CONNECT 17 VSS 18 P0.0/TXD0/PWM1 19 P1.31/TRST 20 P0.1/RXD0/PWM3/EINT0 21 P0.2/SCL0/CAP0.0 22 VDD 23 P1.26/RTCK 24 VSS 25 P0.3/SDA0/MAT0.0/EINT1 26 P0.4/SCK0/CAP0.1/AD0.6 27 P1.25/EXTIN0 28 P0.5/MISO0/MAT0.1/AD0.7 29 P0.6/MOSI0/CAP0.2 30 P0.7/SSEL0/PWM2/EINT2 31 P1.24/TRACECLK 32 002aab734 Fig 3. LPC2142 pinning LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 5 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers 54 P0.19/MAT1.2/MOSI1/CAP1.2 53 P0.18/CAP1.3/MISO1/MAT1.3 55 P0.20/MAT1.3/SSEL1/EINT3 58 P0.23/VBUS 52 P1.30/TMS 64 P1.27/TDO 56 P1.29/TCK 60 P1.28/TDI 57 RESET 62 XTAL1 61 XTAL2 63 VREF P0.21/PWM5/AD1.6/CAP1.3 P0.22/AD1.7/CAP0.0/MAT0.0 RTCX1 P1.19/TRACEPKT3 RTCX2 VSS VDDA P1.18/TRACEPKT2 P0.25/AD0.4/AOUT 1 2 3 4 5 6 7 8 9 49 VBAT 59 VSSA 51 VDD 50 VSS 48 P1.20/TRACESYNC 47 P0.17/CAP1.2/SCK1/MAT1.2 46 P0.16/EINT0/MAT0.2/CAP0.2 45 P0.15/RI1/EINT2/AD1.5 44 P1.21/PIPESTAT0 43 VDD 42 VSS 41 P0.14/DCD1/EINT1/SDA1 40 P1.22/PIPESTAT1 39 P0.13/DTR1/MAT1.1/AD1.4 38 P0.12/DSR1/MAT1.0/AD1.3 37 P0.11/CTS1/CAP1.1/SCL1 36 P1.23/PIPESTAT2 35 P0.10/RTS1/CAP1.0/AD1.2 34 P0.9/RXD1/PWM6/EINT3 33 P0.8/TXD1/PWM4/AD1.1 LPC2144/2146/2148 D+ 10 D− 11 P1.17/TRACEPKT1 12 P0.28/AD0.1/CAP0.2/MAT0.2 13 P0.29/AD0.2/CAP0.3/MAT0.3 14 P0.30/AD0.3/EINT3/CAP0.0 15 P1.16/TRACEPKT0 16 P0.31/UP_LED/CONNECT 17 VSS 18 P0.0/TXD0/PWM1 19 P1.31/TRST 20 P0.1/RXD0/PWM3/EINT0 21 P0.2/SCL0/CAP0.0 22 VDD 23 P1.26/RTCK 24 VSS 25 P0.3/SDA0/MAT0.0/EINT1 26 P0.4/SCK0/CAP0.1/AD0.6 27 P1.25/EXTIN0 28 P0.5/MISO0/MAT0.1/AD0.7 29 P0.6/MOSI0/CAP0.2/AD1.0 30 P0.7/SSEL0/PWM2/EINT2 31 P1.24/TRACECLK 32 002aab735 Fig 4. LPC2144/2146/2148 pinning LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 6 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers 5.2 Pin description Table 3. Symbol P0.0 to P0.31 Pin description Pin Type I/O Description Port 0: Port 0 is a 32-bit I/O port with individual direction controls for each bit. Total of 31 pins of the Port 0 can be used as a general purpose bidirectional digital I/Os while P0.31 is output only pin. The operation of port 0 pins depends upon the pin function selected via the pin connect block. Pins P0.24, P0.26 and P0.27 are not available P0.0/TXD0/ PWM1 19[1] I/O O O P0.1/RXD0/ PWM3/EINT0 21[2] I/O I O I P0.2/SCL0/ CAP0.0 22[3] I/O I/O I P0.3/SDA0/ MAT0.0/EINT1 26[3] I/O I/O O I P0.4/SCK0/ CAP0.1/AD0.6 27[4] I/O I/O I I P0.5/MISO0/ MAT0.1/AD0.7 29[4] I/O I/O O I P0.6/MOSI0/ CAP0.2/AD1.0 30[4] I/O I/O I I P0.7/SSEL0/ PWM2/EINT2 31[2] I/O I O I P0.8/TXD1/ PWM4/AD1.1 33[4] I/O O O I LPC2141_42_44_46_48_3 P0.0 — General purpose input/output digital pin (GPIO) TXD0 — Transmitter output for UART0 PWM1 — Pulse Width Modulator output 1 P0.1 — General purpose input/output digital pin (GPIO) RXD0 — Receiver input for UART0 PWM3 — Pulse Width Modulator output 3 EINT0 — External interrupt 0 input P0.2 — General purpose input/output digital pin (GPIO) SCL0 — I2C0 clock input/output, open-drain output (for I2C-bus compliance) CAP0.0 — Capture input for Timer 0, channel 0 P0.3 — General purpose input/output digital pin (GPIO) SDA0 — I2C0 data input/output, open-drain output (for I2C-bus compliance) MAT0.0 — Match output for Timer 0, channel 0 EINT1 — External interrupt 1 input P0.4 — General purpose input/output digital pin (GPIO) SCK0 — Serial clock for SPI0, SPI clock output from master or input to slave CAP0.1 — Capture input for Timer 0, channel 0 AD0.6 — ADC 0, input 6 P0.5 — General purpose input/output digital pin (GPIO) MISO0 — Master In Slave OUT for SPI0, data input to SPI master or data output from SPI slave MAT0.1 — Match output for Timer 0, channel 1 AD0.7 — ADC 0, input 7 P0.6 — General purpose input/output digital pin (GPIO) MOSI0 — Master Out Slave In for SPI0, data output from SPI master or data input to SPI slave CAP0.2 — Capture input for Timer 0, channel 2 AD1.0 — ADC 1, input 0, available in LPC2144/46/48 only P0.7 — General purpose input/output digital pin (GPIO) SSEL0 — Slave Select for SPI0, selects the SPI interface as a slave PWM2 — Pulse Width Modulator output 2 EINT2 — External interrupt 2 input P0.8 — General purpose input/output digital pin (GPIO) TXD1 — Transmitter output for UART1 PWM4 — Pulse Width Modulator output 4 AD1.1 — ADC 1, input 1, available in LPC2144/46/48 only © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 7 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers Table 3. Symbol Pin description …continued Pin 34[2] Type I/O I O I Description P0.9 — General purpose input/output digital pin (GPIO) RXD1 — Receiver input for UART1 PWM6 — Pulse Width Modulator output 6 EINT3 — External interrupt 3 input P0.10 — General purpose input/output digital pin (GPIO) RTS1 — Request to Send output for UART1, LPC2144/46/48 only CAP1.0 — Capture input for Timer 1, channel 0 AD1.2 — ADC 1, input 2, available in LPC2144/46/48 only P0.11 — General purpose input/output digital pin (GPIO) CTS1 — Clear to Send input for UART1, available in LPC2144/46/48 only CAP1.1 — Capture input for Timer 1, channel 1 SCL1 — I2C1 clock input/output, open-drain output (for I2C-bus compliance) P0.12 — General purpose input/output digital pin (GPIO) DSR1 — Data Set Ready input for UART1, available in LPC2144/46/48 only MAT1.0 — Match output for Timer 1, channel 0 AD1.3 — ADC input 3, available in LPC2144/46/48 only P0.13 — General purpose input/output digital pin (GPIO) DTR1 — Data Terminal Ready output for UART1, LPC2144/46/48 only MAT1.1 — Match output for Timer 1, channel 1 AD1.4 — ADC input 4, available in LPC2144/46/48 only P0.14 — General purpose input/output digital pin (GPIO) DCD1 — Data Carrier Detect input for UART1, LPC2144/46/48 only EINT1 — External interrupt 1 input SDA1 — I2C1 data input/output, open-drain output (for I2C-bus compliance) Note: LOW on this pin while RESET is LOW forces on-chip boot loader to take over control of the part after reset P0.9/RXD1/ PWM6/EINT3 P0.10/RTS1/ CAP1.0/AD1.2 35[4] I/O O I I P0.11/CTS1/ CAP1.1/SCL1 37[3] I/O I I I/O P0.12/DSR1/ MAT1.0/AD1.3 38[4] I/O I O I P0.13/DTR1/ MAT1.1/AD1.4 39[4] I/O O O I P0.14/DCD1/ EINT1/SDA1 41[3] I/O I I I/O P0.15/RI1/ EINT2/AD1.5 45[4] I/O I I I P0.15 — General purpose input/output digital pin (GPIO) RI1 — Ring Indicator input for UART1, available in LPC2144/46/48 only EINT2 — External interrupt 2 input AD1.5 — ADC 1, input 5, available in LPC2144/46/48 only P0.16 — General purpose input/output digital pin (GPIO) EINT0 — External interrupt 0 input MAT0.2 — Match output for Timer 0, channel 2 CAP0.2 — Capture input for Timer 0, channel 2 P0.17 — General purpose input/output digital pin (GPIO) CAP1.2 — Capture input for Timer 1, channel 2 SCK1 — Serial Clock for SSP, clock output from master or input to slave MAT1.2 — Match output for Timer 1, channel 2 P0.16/EINT0/ MAT0.2/CAP0.2 46[2] I/O I O I P0.17/CAP1.2/ SCK1/MAT1.2 47[1] I/O I I/O O LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 8 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers Table 3. Symbol Pin description …continued Pin 53[1] Type I/O I I/O O Description P0.18 — General purpose input/output digital pin (GPIO) CAP1.3 — Capture input for Timer 1, channel 3 MISO1 — Master In Slave Out for SSP, data input to SPI master or data output from SSP slave MAT1.3 — Match output for Timer 1, channel 3 P0.19 — General purpose input/output digital pin (GPIO) MAT1.2 — Match output for Timer 1, channel 2 MOSI1 — Master Out Slave In for SSP, data output from SSP master or data input to SSP slave CAP1.2 — Capture input for Timer 1, channel 2 P0.20 — General purpose input/output digital pin (GPIO) MAT1.3 — Match output for Timer 1, channel 3 SSEL1 — Slave Select for SSP, selects the SSP interface as a slave EINT3 — External interrupt 3 input P0.21 — General purpose input/output digital pin (GPIO) PWM5 — Pulse Width Modulator output 5 AD1.6 — ADC 1, input 6, available in LPC2144/46/48 only CAP1.3 — Capture input for Timer 1, channel 3 P0.22 — General purpose input/output digital pin (GPIO) AD1.7 — ADC 1, input 7, available in LPC2144/46/48 only CAP0.0 — Capture input for Timer 0, channel 0 MAT0.0 — Match output for Timer 0, channel 0 P0.23 — General purpose input/output digital pin (GPIO) VBUS — Indicates the presence of USB bus power Note: This signal must be HIGH for USB reset to occur P0.25 — General purpose input/output digital pin (GPIO) AD0.4 — ADC 0, input 4 AOUT — DAC output, available in LPC2142/44/46/48 only P0.28 — General purpose input/output digital pin (GPIO) AD0.1 — ADC 0, input 1 CAP0.2 — Capture input for Timer 0, channel 2 MAT0.2 — Match output for Timer 0, channel 2 P0.29 — General purpose input/output digital pin (GPIO) AD0.2 — ADC 0, input 2 CAP0.3 — Capture input for Timer 0, Channel 3 MAT0.3 — Match output for Timer 0, channel 3 P0.30 — General purpose input/output digital pin (GPIO) AD0.3 — ADC 0, input 3 EINT3 — External interrupt 3 input CAP0.0 — Capture input for Timer 0, channel 0 P0.18/CAP1.3/ MISO1/MAT1.3 P0.19/MAT1.2/ MOSI1/CAP1.2 54[1] I/O O I/O I P0.20/MAT1.3/ SSEL1/EINT3 55[2] I/O O I I P0.21/PWM5/ AD1.6/CAP1.3 1[4] I/O O I I P0.22/AD1.7/ CAP0.0/MAT0.0 2[4] I/O I I O P0.23/VBUS 58[1] I/O I P0.25/AD0.4/ AOUT 9[5] I/O I O P0.28/AD0.1/ CAP0.2/MAT0.2 13[4] I/O I I O P0.29/AD0.2/ CAP0.3/MAT0.3 14[4] I/O I I O P0.30/AD0.3/ EINT3/CAP0.0 15[4] I/O I I I LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 9 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers Table 3. Symbol Pin description …continued Pin Type O O Description P0.31 — General purpose output only digital pin (GPO) UP_LED — USB GoodLink LED indicator, it is LOW when device is configured (non-control endpoints enabled), it is HIGH when the device is not configured or during global suspend CONNECT — Signal used to switch an external 1.5 kΩ resistor under the software control, used with the SoftConnect USB feature Important: This is an digital output only pin, this pin MUST NOT be externally pulled LOW when RESET pin is LOW or the JTAG port will be disabled P0.31/UP_LED/ 17[6] CONNECT O P1.0 to P1.31 I/O Port 1: Port 1 is a 32-bit bidirectional I/O port with individual direction controls for each bit, the operation of port 1 pins depends upon the pin function selected via the pin connect block, pins 0 through 15 of port 1 are not available P1.16 — General purpose input/output digital pin (GPIO) TRACEPKT0 — Trace Packet, bit 0, standard I/O port with internal pull-up P1.17 — General purpose input/output digital pin (GPIO) TRACEPKT1 — Trace Packet, bit 1, standard I/O port with internal pull-up P1.18 — General purpose input/output digital pin (GPIO) TRACEPKT2 — Trace Packet, bit 2, standard I/O port with internal pull-up P1.19 — General purpose input/output digital pin (GPIO) TRACEPKT3 — Trace Packet, bit 3, standard I/O port with internal pull-up P1.20 — General purpose input/output digital pin (GPIO) TRACESYNC — Trace Synchronization, standard I/O port with internal pull-up Note: LOW on this pin while RESET is LOW enables pins P1.25:16 to operate as Trace port after reset P1.16/ TRACEPKT0 P1.17/ TRACEPKT1 P1.18/ TRACEPKT2 P1.19/ TRACEPKT3 P1.20/ TRACESYNC 16[6] 12[6] 8[6] 4[6] 48[6] I/O O I/O O I/O O I/O O I/O O P1.21/ PIPESTAT0 P1.22/ PIPESTAT1 P1.23/ PIPESTAT2 P1.24/ TRACECLK P1.25/EXTIN0 P1.26/RTCK 44[6] 40[6] 36[6] 32[6] 28[6] 24[6] I/O O I/O O I/O O I/O O I/O I I/O I/O P1.21 — General purpose input/output digital pin (GPIO) PIPESTAT0 — Pipeline Status, bit 0, standard I/O port with internal pull-up P1.22 — General purpose input/output digital pin (GPIO) PIPESTAT1 — Pipeline Status, bit 1, standard I/O port with internal pull-up P1.23 — General purpose input/output digital pin (GPIO) PIPESTAT2 — Pipeline Status, bit 2, standard I/O port with internal pull-up P1.24 — General purpose input/output digital pin (GPIO) TRACECLK — Trace Clock, standard I/O port with internal pull-up P1.25 — General purpose input/output digital pin (GPIO) EXTIN0 — External Trigger Input, standard I/O with internal pull-up P1.26 — General purpose input/output digital pin (GPIO) RTCK — Returned Test Clock output, extra signal added to the JTAG port, assists debugger synchronization when processor frequency varies, bidirectional pin with internal pull-up Note: LOW on RTCK while RESET is LOW enables pins P1.31:26 to operate as Debug port after reset P1.27/TDO 64[6] I/O O P1.27 — General purpose input/output digital pin (GPIO) TDO — Test Data out for JTAG interface LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 10 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers Table 3. Symbol P1.28/TDI P1.29/TCK P1.30/TMS Pin description …continued Pin 60[6] 56[6] 52[6] 20[6] 10[7] 11[7] 57[8] Type I/O I I/O I I/O I I/O I I/O I/O I Description P1.28 — General purpose input/output digital pin (GPIO) TDI — Test Data in for JTAG interface P1.29 — General purpose input/output digital pin (GPIO) TCK — Test Clock for JTAG interface P1.30 — General purpose input/output digital pin (GPIO) TMS — Test Mode Select for JTAG interface P1.31 — General purpose input/output digital pin (GPIO) TRST — Test Reset for JTAG interface USB bidirectional D+ line USB bidirectional D− line External reset input: A LOW on this pin resets the device, causing I/O ports and peripherals to take on their default states, and processor execution to begin at address 0, TTL with hysteresis, 5 V tolerant Input to the oscillator circuit and internal clock generator circuits Output from the oscillator amplifier Input to the RTC oscillator circuit Output from the RTC oscillator circuit Ground: 0 V reference Analog ground: 0 V reference, this should nominally be the same voltage as VSS, but should be isolated to minimize noise and error 3.3 V power supply: This is the power supply voltage for the core and I/O ports Analog 3.3 V power supply: This should be nominally the same voltage as VDD but should be isolated to minimize noise and error, this voltage is only used to power the on-chip ADC(s) and DAC ADC reference voltage: This should be nominally less than or equal to the VDD voltage but should be isolated to minimize noise and error, level on this pin is used as a reference for ADC(s) and DAC RTC power supply voltage: 3.3 V on this pin supplies the power to the RTC P1.31/TRST D+ D− RESET XTAL1 XTAL2 RTCX1 RTCX2 VSS VSSA VDD VDDA 62[9] 61[9] 3[9] 5[9] I O I O 6, 18, 25, 42, I 50 59 23, 43, 51 7 I I I VREF 63 I VBAT [1] [2] [3] [4] 49 I 5 V tolerant pad providing digital I/O functions with TTL levels and hysteresis and 10 ns slew rate control. 5 V tolerant pad providing digital I/O functions with TTL levels and hysteresis and 10 ns slew rate control. If configured for an input function, this pad utilizes built-in glitch filter that blocks pulses shorter than 3 ns. Open-drain 5 V tolerant digital I/O I2C-bus 400 kHz specification compatible pad. It requires external pull-up to provide an output functionality. 5 V tolerant pad providing digital I/O (with TTL levels and hysteresis and 10 ns slew rate control) and analog input function. If configured for an input function, this pad utilizes built-in glitch filter that blocks pulses shorter than 3 ns. When configured as an ADC input, digital section of the pad is disabled. 5 V tolerant pad providing digital I/O (with TTL levels and hysteresis and 10 ns slew rate control) and analog output function. When configured as the DAC output, digital section of the pad is disabled. 5 V tolerant pad with built-in pull-up resistor providing digital I/O functions with TTL levels and hysteresis and 10 ns slew rate control. The pull-up resistor’s value typically ranges from 60 kΩ to 300 kΩ. Pad is designed in accordance with the Universal Serial Bus (USB) specification, revision 2.0 (Full-speed and Low-speed mode only). 5 V tolerant pad providing digital input (with TTL levels and hysteresis) function only. Pad provides special analog functionality. [5] [6] [7] [8] [9] LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 11 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers 6. Functional description 6.1 Architectural overview The ARM7TDMI-S is a general purpose 32-bit microprocessor, which offers high performance and very low power consumption. The ARM architecture is based on Reduced Instruction Set Computer (RISC) principles, and the instruction set and related decode mechanism are much simpler than those of microprogrammed Complex Instruction Set Computers (CISC). This simplicity results in a high instruction throughput and impressive real-time interrupt response from a small and cost-effective processor core. Pipeline techniques are employed so that all parts of the processing and memory systems can operate continuously. Typically, while one instruction is being executed, its successor is being decoded, and a third instruction is being fetched from memory. The ARM7TDMI-S processor also employs a unique architectural strategy known as Thumb, which makes it ideally suited to high-volume applications with memory restrictions, or applications where code density is an issue. The key idea behind Thumb is that of a super-reduced instruction set. Essentially, the ARM7TDMI-S processor has two instruction sets: • The standard 32-bit ARM set • A 16-bit Thumb set The Thumb set’s 16-bit instruction length allows it to approach twice the density of standard ARM code while retaining most of the ARM’s performance advantage over a traditional 16-bit processor using 16-bit registers. This is possible because Thumb code operates on the same 32-bit register set as ARM code. Thumb code is able to provide up to 65 % of the code size of ARM, and 160 % of the performance of an equivalent ARM processor connected to a 16-bit memory system. The particular flash implementation in the LPC2141/42/44/46/48 allows for full speed execution also in ARM mode. It is recommended to program performance critical and short code sections (such as interrupt service routines and DSP algorithms) in ARM mode. The impact on the overall code size will be minimal but the speed can be increased by 30 % over Thumb mode. 6.2 On-chip flash program memory The LPC2141/42/44/46/48 incorporate a 32 kB, 64 kB, 128 kB, 256 kB and 512 kB flash memory system respectively. This memory may be used for both code and data storage. Programming of the flash memory may be accomplished in several ways. It may be programmed In System via the serial port. The application program may also erase and/or program the flash while the application is running, allowing a great degree of flexibility for data storage field firmware upgrades, etc. Due to the architectural solution chosen for an on-chip boot loader, flash memory available for user’s code on LPC2141/42/44/46/48 is 32 kB, 64 kB, 128 kB, 256 kB and 500 kB respectively. The LPC2141/42/44/46/48 flash memory provides a minimum of 100000 erase/write cycles and 20 years of data-retention. LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 12 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers 6.3 On-chip static RAM On-chip static RAM may be used for code and/or data storage. The SRAM may be accessed as 8-bit, 16-bit, and 32-bit. The LPC2141, LPC2142/44 and LPC2146/48 provide 8 kB, 16 kB and 32 kB of static RAM respectively. In case of LPC2146/48 only, an 8 kB SRAM block intended to be utilized mainly by the USB can also be used as a general purpose RAM for data storage and code storage and execution. 6.4 Memory map The LPC2141/42/44/46/48 memory map incorporates several distinct regions, as shown in Figure 5. In addition, the CPU interrupt vectors may be remapped to allow them to reside in either flash memory (the default) or on-chip static RAM. This is described in Section 6.19 “System control”. 4.0 GB AHB PERIPHERALS 3.75 GB VPB PERIPHERALS 3.5 GB 3.0 GB 2.0 GB RESERVED ADDRESS SPACE BOOT BLOCK (12 kB REMAPPED FROM ON-CHIP FLASH MEMORY RESERVED ADDRESS SPACE 0xFFFF FFFF 0xF000 0000 0xE000 0000 0xC000 0000 0x8000 0000 0x7FFF FFFF 0x7FFF D000 0x7FFF CFFF 0x7FD0 2000 0x7FD0 1FFF 8 kB ON-CHIP USB DMA RAM (LPC2146/2148) RESERVED ADDRESS SPACE 32 kB ON-CHIP STATIC RAM (LPC2146/2148) 16 kB ON-CHIP STATIC RAM (LPC2142/2144) 8 kB ON-CHIP STATIC RAM (LPC2141) 0x7FD0 0000 0x7FCF FFFF 0x4000 8000 0x4000 7FFF 0x4000 4000 0x4000 3FFF 0x4000 2000 0x4000 1FFF 0x4000 0000 0x3FFF FFFF 0x0008 0000 0x0007 FFFF 0x0004 0000 0x0003 FFFF 0x0002 0000 0x0001 FFFF 0x0001 0000 0x0000 FFFF 0x0000 8000 0x0000 7FFF 0x0000 0000 1.0 GB RESERVED ADDRESS SPACE TOTAL OF 512 kB ON-CHIP NON-VOLATILE MEMORY (LPC2148) TOTAL OF 256 kB ON-CHIP NON-VOLATILE MEMORY (LPC2146) TOTAL OF 128 kB ON-CHIP NON-VOLATILE MEMORY (LPC2144) TOTAL OF 64 kB ON-CHIP NON-VOLATILE MEMORY (LPC2142) TOTAL OF 32 kB ON-CHIP NON-VOLATILE MEMORY (LPC2141) 0.0 GB 002aab558 Fig 5. LPC2141/42/44/46/48 memory map LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 13 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers 6.5 Interrupt controller The Vectored Interrupt Controller (VIC) accepts all of the interrupt request inputs and categorizes them as Fast Interrupt Request (FIQ), vectored Interrupt Request (IRQ), and non-vectored IRQ as defined by programmable settings. The programmable assignment scheme means that priorities of interrupts from the various peripherals can be dynamically assigned and adjusted. Fast interrupt request (FIQ) has the highest priority. If more than one request is assigned to FIQ, the VIC combines the requests to produce the FIQ signal to the ARM processor. The fastest possible FIQ latency is achieved when only one request is classified as FIQ, because then the FIQ service routine does not need to branch into the interrupt service routine but can run from the interrupt vector location. If more than one request is assigned to the FIQ class, the FIQ service routine will read a word from the VIC that identifies which FIQ source(s) is (are) requesting an interrupt. Vectored IRQs have the middle priority. Sixteen of the interrupt requests can be assigned to this category. Any of the interrupt requests can be assigned to any of the 16 vectored IRQ slots, among which slot 0 has the highest priority and slot 15 has the lowest. Non-vectored IRQs have the lowest priority. The VIC combines the requests from all the vectored and non-vectored IRQs to produce the IRQ signal to the ARM processor. The IRQ service routine can start by reading a register from the VIC and jumping there. If any of the vectored IRQs are pending, the VIC provides the address of the highest-priority requesting IRQs service routine, otherwise it provides the address of a default routine that is shared by all the non-vectored IRQs. The default routine can read another VIC register to see what IRQs are active. 6.5.1 Interrupt sources Each peripheral device has one interrupt line connected to the Vectored Interrupt Controller, but may have several internal interrupt flags. Individual interrupt flags may also represent more than one interrupt source. 6.6 Pin connect block The pin connect block allows selected pins of the microcontroller to have more than one function. Configuration registers control the multiplexers to allow connection between the pin and the on chip peripherals. Peripherals should be connected to the appropriate pins prior to being activated, and prior to any related interrupt(s) being enabled. Activity of any enabled peripheral function that is not mapped to a related pin should be considered undefined. The Pin Control Module with its pin select registers defines the functionality of the microcontroller in a given hardware environment. After reset all pins of Port 0 and Port 1 are configured as input with the following exceptions: If debug is enabled, the JTAG pins will assume their JTAG functionality; if trace is enabled, the Trace pins will assume their trace functionality. The pins associated with the I2C0 and I2C1 interface are open drain. LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 14 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers 6.7 Fast general purpose parallel I/O (GPIO) Device pins that are not connected to a specific peripheral function are controlled by the GPIO registers. Pins may be dynamically configured as inputs or outputs. Separate registers allow the setting or clearing of any number of outputs simultaneously. The value of the output register may be read back, as well as the current state of the port pins. LPC2141/42/44/46/48 introduce accelerated GPIO functions over prior LPC2000 devices: • • • • GPIO registers are relocated to the ARM local bus for the fastest possible I/O timing Mask registers allow treating sets of port bits as a group, leaving other bits unchanged All GPIO registers are byte addressable Entire port value can be written in one instruction 6.7.1 Features • Bit-level set and clear registers allow a single instruction to set or clear any number of bits in one port • Direction control of individual bits • Separate control of output set and clear • All I/O default to inputs after reset 6.8 10-bit ADC The LPC2141/42 contain one and the LPC2144/46/48 contain two analog to digital converters. These converters are single 10-bit successive approximation analog to digital converters. While ADC0 has six channels, ADC1 has eight channels. Therefore, total number of available ADC inputs for LPC2141/42 is 6 and for LPC2144/46/48 is 14. 6.8.1 Features • • • • • • • 10 bit successive approximation analog to digital converter Measurement range of 0 V to VREF (2.0 V ≤ VREF ≤ VDDA) Each converter capable of performing more than 400000 10-bit samples per second Every analog input has a dedicated result register to reduce interrupt overhead Burst conversion mode for single or multiple inputs Optional conversion on transition on input pin or timer match signal Global Start command for both converters (LPC2142/44/46/48 only) LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 15 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers 6.9 10-bit DAC The DAC enables the LPC2141/42/44/46/48 to generate a variable analog output. The maximum DAC output voltage is the VREF voltage. 6.9.1 Features • • • • 10-bit DAC Buffered output Power-down mode available Selectable speed versus power 6.10 USB 2.0 device controller The USB is a 4-wire serial bus that supports communication between a host and a number (127 max) of peripherals. The host controller allocates the USB bandwidth to attached devices through a token based protocol. The bus supports hot plugging, unplugging, and dynamic configuration of the devices. All transactions are initiated by the host controller. The LPC2141/42/44/46/48 is equipped with a USB device controller that enables 12 Mbit/s data exchange with a USB host controller. It consists of a register interface, serial interface engine, endpoint buffer memory and DMA controller. The serial interface engine decodes the USB data stream and writes data to the appropriate end point buffer memory. The status of a completed USB transfer or error condition is indicated via status registers. An interrupt is also generated if enabled. A DMA controller (available in LPC2146/48 only) can transfer data between an endpoint buffer and the USB RAM. 6.10.1 Features • • • • • • • • • • • Fully compliant with USB 2.0 Full-speed specification Supports 32 physical (16 logical) endpoints Supports control, bulk, interrupt and isochronous endpoints Scalable realization of endpoints at run time Endpoint maximum packet size selection (up to USB maximum specification) by software at run time RAM message buffer size based on endpoint realization and maximum packet size Supports SoftConnect and GoodLink LED indicator, these two functions share one pin Supports bus-powered capability with low suspend current Supports DMA transfer on all non-control endpoints (LPC2146/48 only) One duplex DMA channel serves all endpoints (LPC2146/48 only) Allows dynamic switching between CPU controlled and DMA modes (only in LPC2146/48) • Double buffer implementation for bulk and isochronous endpoints LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 16 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers 6.11 UARTs The LPC2141/42/44/46/48 each contain two UARTs. In addition to standard transmit and receive data lines, the LPC2144/46/48 UART1 also provides a full modem control handshake interface. Compared to previous LPC2000 microcontrollers, UARTs in LPC2141/42/44/46/48 introduce a fractional baud rate generator for both UARTs, enabling these microcontrollers to achieve standard baud rates such as 115200 with any crystal frequency above 2 MHz. In addition, auto-CTS/RTS flow-control functions are fully implemented in hardware (UART1 in LPC2144/46/48 only). 6.11.1 Features • • • • 16 B Receive and Transmit FIFOs Register locations conform to 16C550 industry standard Receiver FIFO trigger points at 1 B, 4 B, 8 B, and 14 B Built-in fractional baud rate generator covering wide range of baud rates without a need for external crystals of particular values control on both UARTs • Transmission FIFO control enables implementation of software (XON/XOFF) flow • LPC2144/46/48 UART1 equipped with standard modem interface signals, this module also provides full support for hardware flow control (auto-CTS/RTS) 6.12 I2C-bus serial I/O controller The LPC2141/42/44/46/48 each contain two I2C-bus controllers. The I2C-bus is bidirectional, for inter-IC control using only two wires: a serial clock line (SCL), and a serial data line (SDA). Each device is recognized by a unique address and can operate as either a receiver-only device (e.g., an LCD driver or a transmitter with the capability to both receive and send information (such as memory)). Transmitters and/or receivers can operate in either master or slave mode, depending on whether the chip has to initiate a data transfer or is only addressed. The I2C-bus is a multi-master bus, it can be controlled by more than one bus master connected to it. The I2C-bus implemented in LPC2141/42/44/46/48 supports bit rates up to 400 kbit/s (Fast I2C-bus). 6.12.1 Features • • • • • • Compliant with standard I2C-bus interface Easy to configure as master, slave, or master/slave Programmable clocks allow versatile rate control Bidirectional data transfer between masters and slaves Multi-master bus (no central master) Arbitration between simultaneously transmitting masters without corruption of serial data on the bus one serial bus • Serial clock synchronization allows devices with different bit rates to communicate via LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 17 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers • Serial clock synchronization can be used as a handshake mechanism to suspend and resume serial transfer • The I2C-bus can be used for test and diagnostic purposes 6.13 SPI serial I/O controller The LPC2141/42/44/46/48 each contain one SPI controller. The SPI is a full duplex serial interface, designed to handle multiple masters and slaves connected to a given bus. Only a single master and a single slave can communicate on the interface during a given data transfer. During a data transfer the master always sends a byte of data to the slave, and the slave always sends a byte of data to the master. 6.13.1 Features • • • • Compliant with SPI specification Synchronous, Serial, Full Duplex, Communication Combined SPI master and slave Maximum data bit rate of one eighth of the input clock rate 6.14 SSP serial I/O controller The LPC2141/42/44/46/48 each contain one SSP. The SSP controller is capable of operation on a SPI, 4-wire SSI, or Microwire bus. It can interact with multiple masters and slaves on the bus. However, only a single master and a single slave can communicate on the bus during a given data transfer. The SSP supports full duplex transfers, with data frames of 4 bits to 16 bits of data flowing from the master to the slave and from the slave to the master. Often only one of these data flows carries meaningful data. 6.14.1 Features • Compatible with Motorola’s SPI, TI’s 4-wire SSI and National Semiconductor’s Microwire buses • • • • Synchronous serial communication Master or slave operation 8-frame FIFOs for both transmit and receive Four bits to 16 bits per frame 6.15 General purpose timers/external event counters The Timer/Counter is designed to count cycles of the peripheral clock (PCLK) or an externally supplied clock and optionally generate interrupts or perform other actions at specified timer values, based on four match registers. It also includes four capture inputs to trap the timer value when an input signal transitions, optionally generating an interrupt. Multiple pins can be selected to perform a single capture or match function, providing an application with ‘or’ and ‘and’, as well as ‘broadcast’ functions among them. The LPC2141/42/44/46/48 can count external events on one of the capture inputs if the minimum external pulse is equal or longer than a period of the PCLK. In this configuration, unused capture lines can be selected as regular timer capture inputs, or used as external interrupts. LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 18 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers 6.15.1 Features • A 32-bit timer/counter with a programmable 32-bit prescaler • External event counter or timer operation • Four 32-bit capture channels per timer/counter that can take a snapshot of the timer value when an input signal transitions, a capture event may also optionally generate an interrupt • Four 32-bit match registers that allow: – Continuous operation with optional interrupt generation on match – Stop timer on match with optional interrupt generation – Reset timer on match with optional interrupt generation • Four external outputs per timer/counter corresponding to match registers, with the following capabilities: – Set LOW on match – Set HIGH on match – Toggle on match – Do nothing on match 6.16 Watchdog timer The purpose of the watchdog is to reset the microcontroller within a reasonable amount of time if it enters an erroneous state. When enabled, the watchdog will generate a system reset if the user program fails to ‘feed’ (or reload) the watchdog within a predetermined amount of time. 6.16.1 Features • Internally resets chip if not periodically reloaded • Debug mode • Enabled by software but requires a hardware reset or a watchdog reset/interrupt to be disabled • • • • Incorrect/Incomplete feed sequence causes reset/interrupt if enabled Flag to indicate watchdog reset Programmable 32-bit timer with internal pre-scaler Selectable time period from (Tcy(PCLK) × 256 × 4) to (Tcy(PCLK) × 232 × 4) in multiples of Tcy(PCLK) × 4 6.17 Real-time clock The RTC is designed to provide a set of counters to measure time when normal or idle operating mode is selected. The RTC has been designed to use little power, making it suitable for battery powered systems where the CPU is not running continuously (Idle mode). 6.17.1 Features • Measures the passage of time to maintain a calendar and clock LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 19 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers • Ultra-low power design to support battery powered systems • Provides Seconds, Minutes, Hours, Day of Month, Month, Year, Day of Week, and Day of Year • Can use either the RTC dedicated 32 kHz oscillator input or clock derived from the external crystal/oscillator input at XTAL1, programmable reference clock divider allows fine adjustment of the RTC • Dedicated power supply pin can be connected to a battery or the main 3.3 V 6.18 Pulse width modulator The PWM is based on the standard timer block and inherits all of its features, although only the PWM function is pinned out on the LPC2141/42/44/46/48. The timer is designed to count cycles of the peripheral clock (PCLK) and optionally generate interrupts or perform other actions when specified timer values occur, based on seven match registers. The PWM function is also based on match register events. The ability to separately control rising and falling edge locations allows the PWM to be used for more applications. For instance, multi-phase motor control typically requires three non-overlapping PWM outputs with individual control of all three pulse widths and positions. Two match registers can be used to provide a single edge controlled PWM output. One match register (MR0) controls the PWM cycle rate, by resetting the count upon match. The other match register controls the PWM edge position. Additional single edge controlled PWM outputs require only one match register each, since the repetition rate is the same for all PWM outputs. Multiple single edge controlled PWM outputs will all have a rising edge at the beginning of each PWM cycle, when an MR0 match occurs. Three match registers can be used to provide a PWM output with both edges controlled. Again, the MR0 match register controls the PWM cycle rate. The other match registers control the two PWM edge positions. Additional double edge controlled PWM outputs require only two match registers each, since the repetition rate is the same for all PWM outputs. With double edge controlled PWM outputs, specific match registers control the rising and falling edge of the output. This allows both positive going PWM pulses (when the rising edge occurs prior to the falling edge), and negative going PWM pulses (when the falling edge occurs prior to the rising edge). 6.18.1 Features • Seven match registers allow up to six single edge controlled or three double edge controlled PWM outputs, or a mix of both types • The match registers also allow: – Continuous operation with optional interrupt generation on match – Stop timer on match with optional interrupt generation – Reset timer on match with optional interrupt generation LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 20 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers • Supports single edge controlled and/or double edge controlled PWM outputs. Single edge controlled PWM outputs all go HIGH at the beginning of each cycle unless the output is a constant LOW. Double edge controlled PWM outputs can have either edge occur at any position within a cycle. This allows for both positive going and negative going pulses. • Pulse period and width can be any number of timer counts. This allows complete flexibility in the trade-off between resolution and repetition rate. All PWM outputs will occur at the same repetition rate. • Double edge controlled PWM outputs can be programmed to be either positive going or negative going pulses. • Match register updates are synchronized with pulse outputs to prevent generation of erroneous pulses. Software must ‘release’ new match values before they can become effective. • May be used as a standard timer if the PWM mode is not enabled • A 32-bit Timer/Counter with a programmable 32-bit Prescaler 6.19 System control 6.19.1 Crystal oscillator On-chip integrated oscillator operates with external crystal in range of 1 MHz to 25 MHz. The oscillator output frequency is called fosc and the ARM processor clock frequency is referred to as CCLK for purposes of rate equations, etc. fosc and CCLK are the same value unless the PLL is running and connected. Refer to Section 6.19.2 “PLL” for additional information. 6.19.2 PLL The PLL accepts an input clock frequency in the range of 10 MHz to 25 MHz. The input frequency is multiplied up into the range of 10 MHz to 60 MHz with a Current Controlled Oscillator (CCO). The multiplier can be an integer value from 1 to 32 (in practice, the multiplier value cannot be higher than 6 on this family of microcontrollers due to the upper frequency limit of the CPU). The CCO operates in the range of 156 MHz to 320 MHz, so there is an additional divider in the loop to keep the CCO within its frequency range while the PLL is providing the desired output frequency. The output divider may be set to divide by 2, 4, 8, or 16 to produce the output clock. Since the minimum output divider value is 2, it is insured that the PLL output has a 50 % duty cycle. The PLL is turned off and bypassed following a chip reset and may be enabled by software. The program must configure and activate the PLL, wait for the PLL to Lock, then connect to the PLL as a clock source. The PLL settling time is 100 µs. 6.19.3 Reset and wake-up timer Reset has two sources on the LPC2141/42/44/46/48: the RESET pin and watchdog reset. The RESET pin is a Schmitt trigger input pin with an additional glitch filter. Assertion of chip reset by any source starts the Wake-up Timer (see Wake-up Timer description below), causing the internal chip reset to remain asserted until the external reset is de-asserted, the oscillator is running, a fixed number of clocks have passed, and the on-chip flash controller has completed its initialization. LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 21 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers When the internal reset is removed, the processor begins executing at address 0, which is the reset vector. At that point, all of the processor and peripheral registers have been initialized to predetermined values. The Wake-up Timer ensures that the oscillator and other analog functions required for chip operation are fully functional before the processor is allowed to execute instructions. This is important at power on, all types of reset, and whenever any of the aforementioned functions are turned off for any reason. Since the oscillator and other functions are turned off during Power-down mode, any wake-up of the processor from Power-down mode makes use of the Wake-up Timer. The Wake-up Timer monitors the crystal oscillator as the means of checking whether it is safe to begin code execution. When power is applied to the chip, or some event caused the chip to exit Power-down mode, some time is required for the oscillator to produce a signal of sufficient amplitude to drive the clock logic. The amount of time depends on many factors, including the rate of VDD ramp (in the case of power on), the type of crystal and its electrical characteristics (if a quartz crystal is used), as well as any other external circuitry (e.g. capacitors), and the characteristics of the oscillator itself under the existing ambient conditions. 6.19.4 Brownout detector The LPC2141/42/44/46/48 include 2-stage monitoring of the voltage on the VDD pins. If this voltage falls below 2.9 V, the BOD asserts an interrupt signal to the VIC. This signal can be enabled for interrupt; if not, software can monitor the signal by reading dedicated register. The second stage of low voltage detection asserts reset to inactivate the LPC2141/42/44/46/48 when the voltage on the VDD pins falls below 2.6 V. This reset prevents alteration of the flash as operation of the various elements of the chip would otherwise become unreliable due to low voltage. The BOD circuit maintains this reset down below 1 V, at which point the POR circuitry maintains the overall reset. Both the 2.9 V and 2.6 V thresholds include some hysteresis. In normal operation, this hysteresis allows the 2.9 V detection to reliably interrupt, or a regularly-executed event loop to sense the condition. 6.19.5 Code security This feature of the LPC2141/42/44/46/48 allow an application to control whether it can be debugged or protected from observation. If after reset on-chip boot loader detects a valid checksum in flash and reads 0x8765 4321 from address 0x1FC in flash, debugging will be disabled and thus the code in flash will be protected from observation. Once debugging is disabled, it can be enabled only by performing a full chip erase using the ISP. 6.19.6 External interrupt inputs The LPC2141/42/44/46/48 include up to nine edge or level sensitive External Interrupt Inputs as selectable pin functions. When the pins are combined, external events can be processed as four independent interrupt signals. The External Interrupt Inputs can optionally be used to wake-up the processor from Power-down mode. LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 22 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers Additionally capture input pins can also be used as external interrupts without the option to wake the device up from Power-down mode. 6.19.7 Memory mapping control The Memory Mapping Control alters the mapping of the interrupt vectors that appear beginning at address 0x0000 0000. Vectors may be mapped to the bottom of the on-chip flash memory, or to the on-chip static RAM. This allows code running in different memory spaces to have control of the interrupts. 6.19.8 Power control The LPC2141/42/44/46/48 supports two reduced power modes: Idle mode and Power-down mode. In Idle mode, execution of instructions is suspended until either a reset or interrupt occurs. Peripheral functions continue operation during Idle mode and may generate interrupts to cause the processor to resume execution. Idle mode eliminates power used by the processor itself, memory systems and related controllers, and internal buses. In Power-down mode, the oscillator is shut down and the chip receives no internal clocks. The processor state and registers, peripheral registers, and internal SRAM values are preserved throughout Power-down mode and the logic levels of chip output pins remain static. The Power-down mode can be terminated and normal operation resumed by either a reset or certain specific interrupts that are able to function without clocks. Since all dynamic operation of the chip is suspended, Power-down mode reduces chip power consumption to nearly zero. Selecting an external 32 kHz clock instead of the PCLK as a clock-source for the on-chip RTC will enable the microcontroller to have the RTC active during Power-down mode. Power-down current is increased with RTC active. However, it is significantly lower than in Idle mode. A Power Control for Peripherals feature allows individual peripherals to be turned off if they are not needed in the application, resulting in additional power savings during active and Idle mode. 6.19.9 VPB bus The VPB divider determines the relationship between the processor clock (CCLK) and the clock used by peripheral devices (PCLK). The VPB divider serves two purposes. The first is to provide peripherals with the desired PCLK via VPB bus so that they can operate at the speed chosen for the ARM processor. In order to achieve this, the VPB bus may be slowed down to 1⁄2 to 1⁄4 of the processor clock rate. Because the VPB bus must work properly at power-up (and its timing cannot be altered if it does not work since the VPB divider control registers reside on the VPB bus), the default condition at reset is for the VPB bus to run at 1⁄4 of the processor clock rate. The second purpose of the VPB divider is to allow power savings when an application does not require any peripherals to run at the full processor rate. Because the VPB divider is connected to the PLL output, the PLL remains active (if it was running) during Idle mode. LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 23 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers 6.20 Emulation and debugging The LPC2141/42/44/46/48 support emulation and debugging via a JTAG serial port. A trace port allows tracing program execution. Debugging and trace functions are multiplexed only with GPIOs on Port 1. This means that all communication, timer and interface peripherals residing on Port 0 are available during the development and debugging phase as they are when the application is run in the embedded system itself. 6.20.1 EmbeddedICE Standard ARM EmbeddedICE logic provides on-chip debug support. The debugging of the target system requires a host computer running the debugger software and an EmbeddedICE protocol convertor. EmbeddedICE protocol convertor converts the remote debug protocol commands to the JTAG data needed to access the ARM core. The ARM core has a Debug Communication Channel (DCC) function built-in. The DCC allows a program running on the target to communicate with the host debugger or another separate host without stopping the program flow or even entering the debug state. The DCC is accessed as a co-processor 14 by the program running on the ARM7TDMI-S core. The DCC allows the JTAG port to be used for sending and receiving data without affecting the normal program flow. The DCC data and control registers are mapped in to addresses in the EmbeddedICE logic. 6.20.2 Embedded trace Since the LPC2141/42/44/46/48 have significant amounts of on-chip memory, it is not possible to determine how the processor core is operating simply by observing the external pins. The Embedded Trace Macrocell (ETM) provides real-time trace capability for deeply embedded processor cores. It outputs information about processor execution to the trace port. The ETM is connected directly to the ARM core and not to the main AMBA system bus. It compresses the trace information and exports it through a narrow trace port. An external trace port analyzer must capture the trace information under software debugger control. Instruction trace (or PC trace) shows the flow of execution of the processor and provides a list of all the instructions that were executed. Instruction trace is significantly compressed by only broadcasting branch addresses as well as a set of status signals that indicate the pipeline status on a cycle by cycle basis. Trace information generation can be controlled by selecting the trigger resource. Trigger resources include address comparators, counters and sequencers. Since trace information is compressed the software debugger requires a static image of the code being executed. Self-modifying code can not be traced because of this restriction. 6.20.3 RealMonitor RealMonitor is a configurable software module, developed by ARM Inc., which enables real-time debug. It is a lightweight debug monitor that runs in the background while users debug their foreground application. It communicates with the host using the DCC, which is present in the EmbeddedICE logic. The LPC2141/42/44/46/48 contain a specific configuration of RealMonitor software programmed into the on-chip flash memory. LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 24 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers 7. Limiting values Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134).[1] Symbol VDD VDDA Vi(VBAT) Vi(VREF) VIA VI Parameter supply voltage analog 3.3 V pad supply voltage input voltage on pin VBAT input voltage on pin VREF analog input voltage input voltage 5 V tolerant I/O pins other I/O pins IDD ISS Tstg Ptot(pack) supply current ground current storage temperature total power dissipation (per package) based on package heat transfer, not device power consumption [3] [4][5] Conditions [2] Min −0.5 −0.5 −0.5 −0.5 −0.5 −0.5 −0.5 −40 - Max +3.6 +4.6 +4.6 +4.6 +5.1 +6.0 VDD + 0.5 100 100 +125 1.5 Unit V V V V V V V mA mA °C W for the RTC [4][6] [7][8] [8][9] [10] [1] The following applies to the Limiting values: a) This product includes circuitry specifically designed for the protection of its internal devices from the damaging effects of excessive static charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying greater than the rated maximum. b) Parameters are valid over operating temperature range unless otherwise specified. All voltages are with respect to VSS unless otherwise noted. Core and external rail. On ADC related pins. Including voltage on outputs in 3-state mode. Only valid when the VDD supply voltage is present. Not to exceed 4.6 V. Per supply pin. The peak current is limited to 25 times the corresponding maximum current. Per ground pin. [2] [3] [4] [5] [6] [7] [8] [9] [10] Dependent on package type. LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 25 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers 8. Static characteristics Table 5. Static characteristics Ta = −40 °C to +85 °C for commercial applications, unless otherwise specified. Symbol VDD VDDA Vi(VBAT) Vi(VREF) IIL IIH IOZ Ilatch VI VO VIH VIL Vhys VOH VOL IOH IOL IOHS IOLS Ipd Ipu Parameter supply voltage analog 3.3 V pad supply voltage input voltage on pin VBAT input voltage on pin VREF LOW-level input current HIGH-level input current OFF-state output current I/O latch-up current input voltage output voltage HIGH-level input voltage LOW-level input voltage hysteresis voltage HIGH-level output voltage IOH = −4 mA LOW-level output voltage LOW-level output current HIGH-level short-circuit output current LOW-level short-circuit output current pull-down current pull-up current IOL = −4 mA VOL = 0.4 V VOH = 0 V VOL = VDDA VI = 5 V VI = 0 V VDD < VI < 5 V HIGH-level output current VOH = VDD − 0.4 V [7] [7] [7] [7] [8] [3] Conditions [2] Min 3.0 3.0 2.0 2.5 Typ[1] 3.3 3.3 3.3 3.3 0.4 50 −50 0 Max 3.6 3.6 3.6 VDDA 3 3 3 100 5.5 VDD 0.8 0.4 −45 50 150 −85 0 Unit V V V V µA µA µA mA V V V V V V V mA mA mA mA µA µA µA Standard port pins, RESET, RTCK VI = 0 V; no pull-up VI = VDD; no pull-down VO = 0 V; VO = VDD; no pull-up/down −(0.5VDD) < V < (1.5VDD) Tj < 125 °C pin configured to provide a digital function output active [4][5][6] 0 0 2.0 VDD − 0.4 −4 4 10 −15 0 [8] [9] [10] [9] LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 26 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers Table 5. Static characteristics …continued Ta = −40 °C to +85 °C for commercial applications, unless otherwise specified. Symbol IDD(act) Parameter active mode supply current Conditions VDD = 3.3 V; Ta = 25 °C; code Min Typ[1] 15 Max 50 Unit while(1){} executed from flash; no active peripherals CCLK = 10 MHz CCLK = 60 MHz (other parameters as above) VDD = 3.3 V; Ta = 25 °C; code executed from flash; USB enabled and active; all other peripherals disabled CCLK = 12 MHz CCLK = 60 MHz (other parameters as above) IDD(pd) IBATpd Power-down mode supply VDD = 3.3 V; Ta = 25 °C current VDD = 3.3 V; Ta = 85 °C Power-down mode battery RTC clock = 32 kHz supply current (from RTCX pins); Ta = 25 °C VDD = 3.0 V; Vi(VBAT) = 2.5 V VDD = 3.0 V; Vi(VBAT) = 3.0 V IBATact active mode battery supply current CCLK = 60 MHz; PCLK = 15 MHz; PCLK enabled to RTCK; RTC clock = 32 kHz (from RTCX pins); Ta = 25 °C VDD = 3.0 V; Vi(VBAT) = 3.0 V IBATact(opt) optimized active mode battery supply current PCLK disabled to RTCK in the PCONP register; RTC clock = 32 kHz (from RTCX pins); Ta = 25 °C; Vi(VBAT) = 3.3 V CCLK = 25 MHz CCLK = 60 MHz I2C-bus VIH VIL Vhys VOL ILI pins HIGH-level input voltage LOW-level input voltage hysteresis voltage LOW-level output voltage input leakage current IOLS = 3 mA VI = VDD VI = 5 V Oscillator pins Vi(XTAL1) Vo(XTAL2) input voltage on pin XTAL1 output voltage on pin XTAL2 0 0 1.8 1.8 V V [7] [13] [11][12] [11] [11] mA 40 27 70 70 mA mA 57 40 250 15 90 100 500 30 µA 20 78 40 µA mA µA µA µA 23 - µA 0.7VDD 30 0.5VDD 2 10 0.3VDD 0.4 4 22 µA V V V V µA µA LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 27 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers Table 5. Static characteristics …continued Ta = −40 °C to +85 °C for commercial applications, unless otherwise specified. Symbol Vi(RTCX1) Vo(RTCX2) USB pins IOZ VBUS VDI VCM Vth(rs)se OFF-state output current bus supply voltage 0 V < VI < 3.3 V on the USB connector 0.2 0.8 0.8 ±10 5.25 2.5 2.0 µA V V V V Parameter input voltage on pin RTCX1 output voltage on pin RTCX2 Conditions Min 0 0 Typ[1] Max 1.8 1.8 Unit V V differential input sensitivity |(D+) − (D−)| differential common mode includes VDI range voltage range single-ended receiver switching threshold voltage LOW-level output voltage transceiver capacitance driver output impedance for driver which is not high-speed capable pull-up resistance RL of 1.5 kΩ to 3.6 V pin to GND steady state drive [14] VOL VOH Ctrans ZDRV 2.8 29 - 0.3 3.6 20 44 V V pF Ω HIGH-level output voltage RL of 15 kΩ to GND Rpu [1] [2] [3] [4] [5] [6] [7] [8] [9] SoftConnect = ON 1.1 - 1.9 kΩ Typical ratings are not guaranteed. The values listed are at room temperature (25 ˚C), nominal supply voltages. Core and external rail. The RTC typically fails when Vi(VBAT) drops below 1.6 V. Including voltage on outputs in 3-state mode. VDD supply voltages must be present. 3-state outputs go into 3-state mode when VDD is grounded. Accounts for 100 mV voltage drop in all supply lines. Only allowed for a short time period. Minimum condition for VI = 4.5 V, maximum condition for VI = 5.5 V. [10] Applies to P1.16 to P1.31. [11] On pin VBAT. [12] Optimized for low battery consumption. [13] To VSS. [14] Includes external resistors of 18 Ω ± 1 % on D+ and D−. LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 28 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers Table 6. ADC static characteristics VDDA = 2.5 V to 3.6 V; Ta = −40 °C to +85 °C unless otherwise specified. ADC frequency 4.5 MHz. Symbol VIA Cia ED EL(adj) EO EG ET Rvsi Parameter analog input voltage analog input capacitance differential linearity error integral non-linearity offset error gain error absolute error voltage source interface resistance Conditions: VSSA = 0 V, VDDA = 3.3 V. The ADC is monotonic, there are no missing codes. The differential linearity error (ED) is the difference between the actual step width and the ideal step width. See Figure 6. The integral non-linearity (EL(adj)) is the peak difference between the center of the steps of the actual and the ideal transfer curve after appropriate adjustment of gain and offset errors. See Figure 6. The offset error (EO) is the absolute difference between the straight line which fits the actual curve and the straight line which fits the ideal curve. See Figure 6. The gain error (EG) is the relative difference in percent between the straight line fitting the actual transfer curve after removing offset error, and the straight line which fits the ideal transfer curve. See Figure 6. The absolute error (ET) is the maximum difference between the center of the steps of the actual transfer curve of the non-calibrated ADC and the ideal transfer curve. See Figure 6. See Figure 7. [1][2][3] [1][4] [1][5] [1][6] [1][7] [8] Conditions Min 0 - Typ - Max VDDA 1 ±1 ±2 ±3 ±0.5 ±4 40 Unit V pF LSB LSB LSB % LSB kΩ [1] [2] [3] [4] [5] [6] [7] [8] LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 29 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers offset error EO 1023 gain error EG 1022 1021 1020 1019 1018 (2) 7 code out 6 (1) 5 (5) 4 (4) 3 (3) 2 1 1 LSB (ideal) 1018 1019 1020 1021 1022 1023 1024 0 1 offset error EO 2 3 4 5 6 7 Via (LSBideal) 1 LSB = VDDA − VSSA 1024 002aab136 (1) Example of an actual transfer curve. (2) The ideal transfer curve. (3) Differential linearity error (ED). (4) Integral non-linearity (EL(adj)). (5) Center of a step of the actual transfer curve. Fig 6. ADC characteristics LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 30 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers LPC2141/42/44/46/48 20 kΩ ADx.ySAMPLE 3 pF 5 pF ADx.y Rvsi VEXT VSS 002aab834 Fig 7. Suggested ADC interface - LPC2141/42/44/46/48 ADx.y pin LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 31 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers 9. Dynamic characteristics Table 7. Dynamic characteristics of USB pins (full-speed) CL = 50 pF; Rpu = 1.5 kΩ on D+ to VDD; unless otherwise specified Symbol tr tf tFRFM VCRS tFEOPT tFDEOP tJR1 tJR2 tEOPR1 Parameter rise time fall time differential rise and fall time matching output signal crossover voltage source SE0 interval of EOP source jitter for differential transition to SE0 transition receiver jitter to next transition receiver jitter for paired transitions EOP width at receiver 10 % to 90 % must reject as EOP; see Figure 9 must accept as EOP; see Figure 9 [1] Conditions 10 % to 90 % 10 % to 90 % (tr/tf) Min 4 4 90 1.3 Typ - Max 20 20 110 2.0 175 +5 +18.5 +9 - Unit ns ns % V ns ns ns ns ns see Figure 9 see Figure 9 160 −2 −18.5 −9 40 tEOPR2 EOP width at receiver [1] 82 - - ns [1] Characterized but not implemented as production test. Guaranteed by design. Table 8. Dynamic characteristics Ta = −40 °C to +85 °C for commercial applications; VDD over specified ranges[1] Symbol External clock fosc Tcy(clk) tCHCX tCLCX tCLCH tCHCL tr(o) tf(o) I2C-bus tf(o) [1] [2] [3] Parameter oscillator frequency clock cycle time clock HIGH time clock LOW time clock rise time clock fall time output rise time output fall time pins (P0.2, P0.3, P0.11, and P0.14) output fall time Conditions Min 10 40 Tcy(clk) × 0.4 Tcy(clk) × 0.4 - Typ[2] 10 10 - Max 25 100 5 5 - Unit MHz ns ns ns ns ns ns ns ns Port pins (P0.2, P0.3, P0.11, and P0.14) VIH to VIL 20 + 0.1 × Cb[3] Parameters are valid over operating temperature range unless otherwise specified. Typical ratings are not guaranteed. The values listed are at room temperature (25 °C), nominal supply voltages. Bus capacitance Cb in pF, from 10 pF to 400 pF. LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 32 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers 9.1 Timing VDD − 0.5 V 0.45 V 0.2VDD + 0.9 V 0.2VDD − 0.1 V tCHCL tCLCX Tcy(clk) 002aaa907 tCHCX tCLCH VDD = 1.8 V Fig 8. External clock timing tPERIOD crossover point differential data lines crossover point extended source EOP width: tFEOPT differential data to SE0/EOP skew n × tPERIOD + tFDEOP receiver EOP width: tEOPR1, tEOPR2 002aab561 Fig 9. Differential data-to-EOP transition skew and EOP width 10. Application information 10.1 Suggested USB interface solutions VDD CONNECT soft-connect switch LPC2141/42/ 44/46/48 VBUS D+ D− VSS RS = 33 Ω RS = 33 Ω R1 1.5 kΩ USB-B connector 002aab563 Fig 10. LPC2141/42/44/46/48 USB interface using the CONNECT function on pin 17 LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 33 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers VDD R2 LPC2141/42/ 44/46/48 UP_LED VBUS D+ D− VSS RS = 33 Ω RS = 33 Ω R1 1.5 kΩ USB-B connector 002aab562 Fig 11. LPC2141/42/44/46/48 USB interface using the UP_LED function on pin 17 LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 34 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers 11. Package outline LQFP64: plastic low profile quad flat package; 64 leads; body 10 x 10 x 1.4 mm SOT314-2 c y X A 48 49 33 32 ZE e E HE wM bp 64 1 pin 1 index 16 ZD bp D HD wM B vM B vM A 17 detail X L Lp A A2 A1 (A 3) θ e 0 2.5 scale 5 mm DIMENSIONS (mm are the original dimensions) UNIT mm A max. 1.6 A1 0.20 0.05 A2 1.45 1.35 A3 0.25 bp 0.27 0.17 c 0.18 0.12 D (1) 10.1 9.9 E (1) 10.1 9.9 e 0.5 HD HE L 1 Lp 0.75 0.45 v 0.2 w 0.12 y 0.1 Z D (1) Z E (1) 1.45 1.05 1.45 1.05 θ 7o o 0 12.15 12.15 11.85 11.85 Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT314-2 REFERENCES IEC 136E10 JEDEC MS-026 JEITA EUROPEAN PROJECTION ISSUE DATE 00-01-19 03-02-25 Fig 12. Package outline SOT314-2 (LQFP64) LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 35 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers 12. Abbreviations Table 9. Acronym ADC BOD CPU DAC DCC DMA EOP FIFO GPIO PLL POR PWM RAM SE0 SPI SRAM SSP UART USB VPB Acronym list Description Analog-to-Digital Converter Brown-Out Detection Central Processing Unit Digital-to-Analog Converter Debug Communications Channel Direct Memory Access End Of Packet First In, First Out General Purpose Input/Output Phase-Locked Loop Power-On Reset Pulse Width Modulator Random Access Memory Single Ended Zero Serial Peripheral Interface Static Random Access Memory Synchronous Serial Port Universal Asynchronous Receiver/Transmitter Universal Serial Bus VLSI Peripheral Bus LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 36 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers 13. Revision history Table 10. Revision history Release date 20071019 Data sheet status Product data sheet Change notice Supersedes LPC2141_42_44_46_48_2 Document ID LPC2141_42_44_46_48_3 Modifications: • • The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP Semiconductors. Legal texts have been adapted to the new company name where appropriate. Product data sheet Preliminary data sheet LPC2141_42_44_46_48_1 - LPC2141_42_44_46_48_2 LPC2141_42_44_46_48_1 20060828 20051003 LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 37 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers 14. Legal information 14.1 Data sheet status Document status[1][2] Objective [short] data sheet Preliminary [short] data sheet Product [short] data sheet [1] [2] [3] Product status[3] Development Qualification Production Definition This document contains data from the objective specification for product development. This document contains data from the preliminary specification. This document contains the product specification. Please consult the most recently issued document before initiating or completing a design. The term ‘short data sheet’ is explained in section “Definitions”. The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 14.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. 14.3 Disclaimers General — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of a NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. 14.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. I2C-bus — logo is a trademark of NXP B.V. SoftConnect — is a trademark of NXP B.V. GoodLink — is a trademark of NXP B.V. 15. Contact information For additional information, please visit: http://www.nxp.com For sales office addresses, send an email to: salesaddresses@nxp.com LPC2141_42_44_46_48_3 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 03 — 19 October 2007 38 of 39 NXP Semiconductors LPC2141/42/44/46/48 Single-chip 16-bit/32-bit microcontrollers 16. Contents 1 2 2.1 3 3.1 4 5 5.1 5.2 6 6.1 6.2 6.3 6.4 6.5 6.5.1 6.6 6.7 6.7.1 6.8 6.8.1 6.9 6.9.1 6.10 6.10.1 6.11 6.11.1 6.12 6.12.1 6.13 6.13.1 6.14 6.14.1 6.15 6.15.1 6.16 6.16.1 6.17 6.17.1 6.18 6.18.1 6.19 6.19.1 6.19.2 6.19.3 6.19.4 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Key features . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Ordering options . . . . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pinning information . . . . . . . . . . . . . . . . . . . . . . 4 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 7 Functional description . . . . . . . . . . . . . . . . . . 12 Architectural overview. . . . . . . . . . . . . . . . . . . 12 On-chip flash program memory . . . . . . . . . . . 12 On-chip static RAM. . . . . . . . . . . . . . . . . . . . . 13 Memory map. . . . . . . . . . . . . . . . . . . . . . . . . . 13 Interrupt controller . . . . . . . . . . . . . . . . . . . . . 14 Interrupt sources. . . . . . . . . . . . . . . . . . . . . . . 14 Pin connect block . . . . . . . . . . . . . . . . . . . . . . 14 Fast general purpose parallel I/O (GPIO) . . . . 15 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 10-bit ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 10-bit DAC . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 USB 2.0 device controller . . . . . . . . . . . . . . . . 16 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 UARTs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 I2C-bus serial I/O controller . . . . . . . . . . . . . . 17 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 SPI serial I/O controller. . . . . . . . . . . . . . . . . . 18 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 SSP serial I/O controller . . . . . . . . . . . . . . . . . 18 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 General purpose timers/external event counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Watchdog timer. . . . . . . . . . . . . . . . . . . . . . . . 19 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Real-time clock . . . . . . . . . . . . . . . . . . . . . . . . 19 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Pulse width modulator . . . . . . . . . . . . . . . . . . 20 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 System control . . . . . . . . . . . . . . . . . . . . . . . . 21 Crystal oscillator . . . . . . . . . . . . . . . . . . . . . . . 21 PLL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Reset and wake-up timer . . . . . . . . . . . . . . . . 21 Brownout detector. . . . . . . . . . . . . . . . . . . . . . 22 6.19.5 6.19.6 6.19.7 6.19.8 6.19.9 6.20 6.20.1 6.20.2 6.20.3 7 8 9 9.1 10 10.1 11 12 13 14 14.1 14.2 14.3 14.4 15 16 Code security . . . . . . . . . . . . . . . . . . . . . . . . . External interrupt inputs . . . . . . . . . . . . . . . . . Memory mapping control . . . . . . . . . . . . . . . . Power control . . . . . . . . . . . . . . . . . . . . . . . . . VPB bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Emulation and debugging. . . . . . . . . . . . . . . . EmbeddedICE . . . . . . . . . . . . . . . . . . . . . . . . Embedded trace. . . . . . . . . . . . . . . . . . . . . . . RealMonitor . . . . . . . . . . . . . . . . . . . . . . . . . . Limiting values . . . . . . . . . . . . . . . . . . . . . . . . Static characteristics . . . . . . . . . . . . . . . . . . . Dynamic characteristics . . . . . . . . . . . . . . . . . Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Application information . . . . . . . . . . . . . . . . . Suggested USB interface solutions . . . . . . . . Package outline . . . . . . . . . . . . . . . . . . . . . . . . Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . Revision history . . . . . . . . . . . . . . . . . . . . . . . Legal information . . . . . . . . . . . . . . . . . . . . . . Data sheet status . . . . . . . . . . . . . . . . . . . . . . Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . Contact information . . . . . . . . . . . . . . . . . . . . Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 22 23 23 23 24 24 24 24 25 26 32 33 33 33 35 36 37 38 38 38 38 38 38 39 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP B.V. 2007. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 19 October 2007 Document identifier: LPC2141_42_44_46_48_3