0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
MC33493DTBER2

MC33493DTBER2

  • 厂商:

    NXP(恩智浦)

  • 封装:

    TSSOP14_5X4.4MM

  • 描述:

    IC RF TRANSMITTER UHF 14-TSSOP

  • 数据手册
  • 价格&库存
MC33493DTBER2 数据手册
Freescale Semiconductor Data Sheet: Product Preview Document Number: MC33493 Rev. 1.7, 03/2007 MC33493 PLL Tuned UHF Transmitter for Data Transfer Applications • • • • • • • • • • • Selectable frequency bands: 315—434 MHz and 868—928 MHz OOK and FSK modulation Adjustable output power range Fully integrated voltage control oscillator (VCO) Supply voltage range: 1.9—3.6 V Very low standby current: 0.1 nA @ TA= 25 °C Low-supply voltage shutdown Data clock output for microcontroller Extended temperature range: –40 to 125 °C Low external component count Typical application compliant with European Telecommunications Standards Institute (ETSI) standard PIN CONNECTIONS DATACLK 1 14 MODE DATA 2 13 ENABLE BAND 3 12 VCC GND 4 11 GNDRF XTAL1 5 10 RFOUT XTAL0 6 9 VCC REXT 7 8 CFSK Ordering Information Device Ambient Temperature Range Package MC33493DTB –40°C to 125°C TSSOP14 MC3493DTBE –40°C to 125°C TSSOP14 (ROHS) This document contains information on a product under development. Freescale reserves the right to change or discontinue this product without notice. © Freescale Semiconductor, Inc., 2007. All rights reserved. 1 2 3 4 5 6 7 8 9 10 11 12 Transmitter Functional Description . . . . . . . . . . . . . . . . . . . . . .4 Phase Locked Loop and Local Oscillator . . . . . . . . . . . . . . . . .4 Radio Frequency (RF) Output Stage . . . . . . . . . . . . . . . . . . . .4 Modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Microcontroller Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 State Machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Data Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 RF Output Spectrum. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Output Power Measurement . . . . . . . . . . . . . . . . . . . . . . . . . .14 Complete Application Schematic and PCB for OOK Modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 13 Complete Application Schematic and PCB for FSK Modulation. . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 14 Recommendations for FSK Modulation . . . . . . . . . . . . . . . . .19 15 Case Outline Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 List of Figures Figure 1. Simplified Block Diagram . . . . . . . . . . . . . . . . . . . . . . . 3 Figure 2. Crystal Pulling Configurations. . . . . . . . . . . . . . . . . . . . 5 Figure 3. State machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Figure 4. Signals Waveform and Timing Definition . . . . . . . . . . . 7 Figure 5. RF Spectrum at 434 MHz Frequency Band Displayed with a 5 MHz Span . . . . . . . . . . . . . . . . . . . 11 Figure 6. RF Spectrum at 434 MHz Frequency Band Displayed with a 50 MHz Span . . . . . . . . . . . . . . . . . . 11 Figure 7. RF Spectrum at 434 MHz Frequency Band Displayed with a 1.5 GHz Span . . . . . . . . . . . . . . . . . 12 Figure 8. RF Spectrum at 434 MHz Band for a 70 kHz FSK Deviation at 4.8 kbit/s . . . . . . . . . . . 12 Figure 9. Output Power Measurement Configurations . . . . . . . . Figure 10.Output Model and Matching Network for 434 MHz Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 11.Output Power at 434 MHz Band vs Rext Value . . . . . Figure 12.Application Schematic for OOK Modulation, 434 MHz Frequency Band . . . . . . . . . . . . . . . . . . . . . . Figure 13.Two-Button Keyfob Board Layout . . . . . . . . . . . . . . . . Figure 14.Application Schematic for FSK Modulation, Serial Configuration, 434 MHz Frequency Band . . . . . Figure 15.Application PCB Layout for FSK Modulation, Serial Configuration, 434 MHz Frequency Band . . . . . Figure 16.Crystal Load Capacitance Contributors Schematic . . Figure 17.Case Outline Dimensions . . . . . . . . . . . . . . . . . . . . . 13 13 14 15 16 17 18 19 20 List of Tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Pin Function Description . . . . . . . . . . . . . . . . . . . . . . . . 3 Absolute Maximum Ratings. . . . . . . . . . . . . . . . . . . . . . 3 Band Selection and Associated Divider Ratios . . . . . . . 4 DATACLK Frequency vs Crystal Oscillator Frequency. . 5 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 8 External Components Description for OOK. . . . . . . . . 15 Typical Crystal Characteristics (SMD Package) . . . . . 16 External Components Description for FSK . . . . . . . . . 17 Crystal Pulling Capacitor Values vs Carrier Frequency Total Deviation -1- . . . . . . . . . . . . . 18 Table 10.Crystal Pulling Capacitor Values vs Carrier Frequency Total Deviation -2- . . . . . . . . . . . . . 18 Table 11.Pads and Tracks Parasitic Values . . . . . . . . . . . . . . . . 19 PLL Tuned UHF Transmitter for Data Transfer Applications, Rev. 1.7 2 Freescale Semiconductor Figure 1. Simplified Block Diagram Table 1. Pin Function Description Pin Name Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 DATACLK DATA BAND GND XTAL1 XTAL0 REXT CFSK VCC RFOUT GNDRF VCC ENABLE MODE Clock output to the microcontroller Data input Frequency band selection Ground Reference oscillator input Reference oscillator output Power amplifier output current setting input FSK switch output Power supply Power amplifier output Power amplifier ground Power supply Enable input Modulation type selection input Table 2. Absolute Maximum Ratings Parameter Supply voltage Symbol Value Unit VCC VGND – 0.3 to 3.7 V VGND – 0.3 to VCC + 0.3 V ±2000 V ±150 V Voltage allowed on each pin ESD HBM voltage capability on each pin 1(note 1) 2 ESD MM voltage capability on each pin (note 2) Storage temperature Ts –65 to +150 °C Junction temperature Tj +150 °C 1 2 Human Body model, AEC-Q100-002 Rev. C. Machine Model, AEC-Q100-003 Rev. E. PLL Tuned UHF Transmitter for Data Transfer Applications, Rev. 1.7 Freescale Semiconductor 3 Transmitter Functional Description 1 Transmitter Functional Description MC33493 is a PLL-tuned low-power UHF transmitter. The different modes of operation are controlled by the microcontroller through several digital input pins. The power supply voltage ranges from 1.9 V to 3.6 V, allowing operation with a single lithium cell. 2 Phase Locked Loop and Local Oscillator The VCO is a completely integrated relaxation oscillator. The phase frequency detector (PFD) and the loop filter are fully integrated. The exact output frequency is equal to: fRFOUT = fXTAL × [PLL divider ratio]. The frequency band of operation is selected through the BAND pin. Table 3 shows details for each frequency band selection. Table 3. Band Selection and Associated Divider Ratios BAND Input Level High Low Frequency Band (MHz) 315 434 868 PLL Divider Ratio Crystal Oscillator Frequency (MHz) 32 64 9.84 13.56 An out-of-lock function is performed by monitoring the PFD output voltage. When it exceeds defined limits, the RF output stage is disabled. 3 Radio Frequency (RF) Output Stage The radio frequentcy (RF) output stage source is a single-ended square-wave switched current. Harmonics are present in the output current drive. Their radiated absolute level depends on the antenna characteristics and output power. Typical application demonstrates compliance to ETSI standard. A resistor, Rext, connected to the REXT pin controls the output power allowing a trade-off between radiated power and current consumption. The output voltage is internally clamped to Vcc ± 2 Vbe (typ. Vcc ± 1.5 V @ TA=25 °C). 4 Modulation To select the On Off Keying (OOK) modulation, a low-logic level must be applied on the MODE pin. This modulation is performed by switching the RF output stage on or off. The logic level applied on the DATA pin controls the output stage state: DATA = 0 → output stage off, DATA = 1 → output stage on. Applying a high-logic level on the MODE pin selects Frequency Shift Keying (FSK) modulation. This modulation is achieved by crystal pulling. An internal switch connected to the CFSK pin enables switching the external crystal load capacitors. Figure 2 shows the possible configurations: serial and parallel. The logic level applied on pin DATA controls the state of this internal switch: DATA=0 → switch off, DATA=1 → switch on. DATA input is internally re-synchronized by the crystal reference signal. The corresponding jitter on the data duty cycle cannot exceed ±1 reference period (±75 ns for a 13.56 MHz crystal). This crystal pulling solution implies that the RF output frequency deviation equals the crystal frequency deviation multiplied by the PLL Divider ratio (see Table 3). PLL Tuned UHF Transmitter for Data Transfer Applications, Rev. 1.7 4 Freescale Semiconductor Microcontroller Interface Figure 2. Crystal Pulling Configurations 5 Microcontroller Interface Four digital input pins (ENABLE, DATA, BAND, and MODE) enable the circuit to be controlled by a microcontroller. The band frequency and the modulation type should be configured before enabling the circuit. One digital output pin, DATACLK, provides the microcontroller with a reference frequency for data clocking. This frequency is equal to the crystal oscillator frequency divided by 64 (see Table 4). Table 4. DATACLK Frequency vs Crystal Oscillator Frequency Crystal Oscillator Frequency (MHz) DATACLK Frequency (kHz) 9.84 13.56 154 212 PLL Tuned UHF Transmitter for Data Transfer Applications, Rev. 1.7 Freescale Semiconductor 5 State Machine 6 State Machine Figure 3 details the state machine. Power ON AND ENABLE=0 State 1 Standby mode ENABLE=0 ENABLE=1 State 2 PLL out of lock-in range No RF output PLL in lock-in range PLL out of lock-in range ENABLE=0 State 4 Shutdown mode Vbattery < Vshutdown State 3 Transmission mode Figure 3. State machine State 1: The circuit is in standby mode and draws only a leakage current from the power supply. State 2: In this state, the PLL is out of the lock-in range; therefore, the RF output stage is switched off, preventing RF transmission. Data clock is available on the DATACLK pin. Each time the device is enabled, the state machine passes through this state. State 3: In this state, the PLL is within the lock-in range. If t < tPLL_lock_in, the PLL may be in acquisition mode. If t≥tPLL_lock_in, then the PLL is locked. Data entered on the DATA pin are output on the RFOUT pin according to the modulation selected by the level applied on the MODE pin. State 4: When the supply voltage falls below the shutdown voltage threshold (VSDWN,) the entire circuit switches off. After this shutdown, applying a low level on the ENABLE pin unlatches the circuit. Figure 4 shows the waveforms of the main signals for a typical application cycle. PLL Tuned UHF Transmitter for Data Transfer Applications, Rev. 1.7 6 Freescale Semiconductor Power Management ENABLE DATACLK tDATACLK_settling > tPLL_lock_in c tPLL_lock_in DATA MODE=0 (OOK) fcarrier RFOUT fcarrier MODE=1 (FSK) fhigh State 1 flow State 2 fhigh flow State 3 fhigh State 1 c : PLL locked Figure 4. Signals Waveform and Timing Definition 7 Power Management When the battery voltage falls below the shutdown voltage threshold (VSDWN) the entire circuit switches off. After this shutdown, the circuit is latched until a low level is applied on pin ENABLE (see State 4 of the state machine). 8 Data Clock At start-up, data clock timing is valid after the data clock settling time. Because the clock is switched off asynchronously, the last period duration cannot be guaranteed. 9 Electrical Characteristics Unless otherwise specified, voltage range Vcc=[Vshutdown;3.6 V], temperature range TA=[–40 °C;+ 125 °C], Rext=12 kΩ ± 5%, RF output frequency fcarrier = 433.92 MHz, reference frequency freference = 13.560 MHz, output load RL = 50 Ω ±1% (Figure 9). Values refer to the circuit shown in the recommended application schematics: Figure 12 shows OOK modulation and Figure 14 shows FSK modulation. Typical values reflect average measurement at VCC =3 V, TA = 25 °C. PLL Tuned UHF Transmitter for Data Transfer Applications, Rev. 1.7 Freescale Semiconductor 7 Electrical Characteristics Table 5. Electrical Characteristics Limits Parameter Test Conditions, Comments Unit Min. Typ. Max. TA ≤ 25 °C — 0.1 5 nA TA = 60 °C — 7 30 nA 1.3 TA = 85 °C — 40 100 nA 1.4 TA = 125 °C — 800 1700 nA 315 and 434 bands, OOK and FSK modulation, continuous wave, TA = 25 °C — 11.6 13.5 mA 1.6 315 and 434 bands, DATA=0, –40 °C ≤ TA ≤ 125 °C — 4.4 6.0 mA 1.7 868 MHz band, DATA=0, –40 °C ≤ TA ≤ 125 °C — 4.6 6.2 mA 315 and 434 bands, OOK and FSK modulation, continuous wave, –40 °C ≤ TA ≤125 °C — 11.6 14.9 mA 1.8 868 MHz band, OOK and FSK modulation, continuous wave, –40 °C ≤T A ≤ 125 °C — 11.8 15.1 mA 1.9 — 3 3.6 V TA = –40 °C — 2.04 2.11 V 1.12 TA = –20 °C — 1.99 2.06 V 1.13 TA = 25 °C — 1.86 1.95 V 1.14 TA = 60 °C — 1.76 1.84 V 1.15 TA = 85 °C — 1.68 1.78 V 1.16 TA = 125 °C — 1.56 1.67 V 12 — 21 kΩ 315 and 434 MHz bands, with 50 Ω matching network — 5 — dBm 2.3 868 MHz band, with 50 Ω matching network — 1 — dBm 2.4 315 and 434 MHz bands, –40 °C ≤ TA ≤ 125 °C –3 0 3 dBm 2.8 868 MHz band, –40 °C ≤TA ≤ 125 °C –7 –3 0 dBm 315 and 434 MHz bands, with 50 Ω matching network — –0.35 –0.25 — dB/kΩ mA/kΩ 1 1.1 1.2 1.5 General Parameters Supply current in standby mode Supply current in transmission mode 1.10 Supply voltage 1.11 Shutdown voltage threshold 2 2.1 2.2 2.12 RF Parameters Rext value Output power Current and output power variation vs. Rext value PLL Tuned UHF Transmitter for Data Transfer Applications, Rev. 1.7 8 Freescale Semiconductor Electrical Characteristics Table 5. Electrical Characteristics (continued) Limits Parameter Test Conditions, Comments Unit Min. Typ. Max. 315 and 434 MHz bands, with 50 Ω matching network — –34 — dBc 2.14 868 MHz band, with 50 Ω matching network — –49 — dBc 2.15 315 and 434 MHz bands — –23 -17 dBc 2.16 868 MHz band — –38 -27 dBc 315 and 434 MHz bands, with 50 Ω matching network — –32 — dBc 2.18 868 MHz band, with 50 Ω matching network — –57 — dBc 2.19 315 and 434 MHz bands — –21 –15 dBc 2.20 868 MHz band — –48 –39 dBc Spurious level @ fcarrier ± f DATACLK 315 and 434 MHz bands — –36 –24 dBc 868 MHz band — –29 –17 dBc Spurious level @ fcarrier ± f reference 315 MHz band — –37 –30 dBc 434 MHz band — –44 –34 dBc 868 MHz band — –37 –27 dBc 315 MHz band — –62 –53 dBc 434 MHz band — –80 –60 dBc 868 MHz band — –45 –39 dBc 315 and 434 MHz bands, ±175 kHz from f carrier — –75 –68 dBc/Hz 868 MHz band, ±175 kHz from f carrier — –73 –66 dBc/Hz fcarrier within 30 kHz from the final value, crystal series resistor = 150 Ω — 400 1600 µs — 1 — pF — 20 200 W 20 50 75 90 — dBc 2.13 2.17 2.21 2.22 2.23 2.24 Harmonic 2 level Harmonic 3 level 2.25 2.41 2.26 Spurious level @ fcarrier/2 2.27 2.30 Phase noise 2.31 2.32 PLL lock-in time, tPLL_lock_in 2.33 XTAL1 input capacitance 2.34 Crystal resistance 2.44 OOK modulation FSK modulation 2.35 OOK modulation depth 2.36 FSK modulation carrier frequency total deviation 315 and 434 MHz bands, see note Note: — — 100 kHz 868 MHz band, see note Note: — — 200 kHz CFSK output resistance MODE = 0, DATA = x MODE = 1, DATA = 0 50 70 — kΩ MODE = 1, DATA = 1 — 90 300 W — 1 — pF — — 10 kbit/s 2.37 2.38 2.39 2.43 CFSK output capacitance 2.40 Data rate Manchester coding PLL Tuned UHF Transmitter for Data Transfer Applications, Rev. 1.7 Freescale Semiconductor 9 RF Output Spectrum Table 5. Electrical Characteristics (continued) Limits Parameter Test Conditions, Comments 2.41 Data to RF delay difference between falling and rising edges, tdelay_difference 2.42 Unit Min. Typ. Max. MODE = 0, see note 3.5 5.25 7.5 µs MODE = 1, see note –200 — 200 ns Note: This parameter is depending on crystal characteristics, load capacitor values (see Table 4) and PCB track capacitance. Note: Delay difference definition Input data From 50% of data edge to corresponding demodulated signal envelope edge: tdelay_difference = tdelay_fall – tdelay_rise Demodulated data tdelay_rise 3 tdelay_fall Microcontroller Interfaces 0 — 0.3 x VCC V Input high voltage 0.7 x VCC — VCC V 3.3 Input hysteresis voltage — — 120 mV 3.4 Input current — — 100 nA 3.5 ENABLE pulldown resistor — 180 — kΩ 0 — 0.25 x VCC V 0.75 x VCC — VCC V — 250 500 ns — 150 400 ns — 800 2000 µs 3.1 3.2 3.6 3.7 Input low voltage Pins: BAND, MODE,DATA = 1 DATACLK output low voltage Cload = 2 pF DATACLK output high voltage 3.8 DATACLK rising time 3.9 DATACLK falling time 3.10 DATACLK settling time, tDATACLK_settling 10 Pins: BAND, MODE, ENABLE, and DATA Cload = 2 pF, measured from 20% to 80% of the voltage swing 45% < duty cycle fDATACLK < 55% RF Output Spectrum The following figures represent spectrums of the transmitter carrier, measured in conduction mode. Three different spans have been used. The 5 MHz span spectrum (Figure 5) shows phase noise response close to the RF carrier and the noise suppression within the PLL-loop bandwidth. The 50 MHz span spectrum (Figure 6) shows phase noise and reference spurious. Finally, the 1.5 GHz span spectrum (Figure 7) shows the second and third harmonics of carrier. All spectrums are measured in OOK modulation at DATA=1. Figure 8 shows the spectrum in case of FSK modulation with 45 kHz deviation at 4 kbit/s data rate. PLL Tuned UHF Transmitter for Data Transfer Applications, Rev. 1.7 10 Freescale Semiconductor RF Output Spectrum Resolution bandwidth: 100kHz Resolution bandwidth: 30kHz Figure 5. RF Spectrum at 434 MHz Frequency Band Displayed with a 5 MHz Span Figure 6. RF Spectrum at 434 MHz Frequency Band Displayed with a 50 MHz Span PLL Tuned UHF Transmitter for Data Transfer Applications, Rev. 1.7 Freescale Semiconductor 11 RF Output Spectrum Figure 7. RF Spectrum at 434 MHz Frequency Band Displayed with a 1.5 GHz Span Figure 8. RF Spectrum at 434 MHz Band for a 70 kHz FSK Deviation at 4.8 kbit/s PLL Tuned UHF Transmitter for Data Transfer Applications, Rev. 1.7 12 Freescale Semiconductor Output Power Measurement 11 Output Power Measurement The RF output levels given in Section 9, “Electrical Characteristics,” are measured with a 50 Ω load directly connected to the RFOUT pin, as shown below in Figure 9. This wideband coupling method gives results independent of the application. VCC Impeder: TDK MMZ1608Y102CTA00 RFOUT RF output 100 pF RL= 50 W Figure 9. Output Power Measurement Configurations The configuration shown in Figure 10(a) provides better efficiency in terms of output power and harmonics rejection. The schematic on Figure 10(b) gives the equivalent circuit of the RFOUT pin and the DC bias impeder as well as matching network components for 434 MHz frequency band. VCC Impeder: TDK MMZ1608Y102CTA00 RFOUT (a) Matching Network RF output RL=50 Ω Matching Network L1 39 nH (b) C0 1.5 pF R0 250 Ω RFOUT pin 3 kΩ Ri Impeder C3 50 Ω 330pF RL Load Figure 10. Output Model and Matching Network for 434 MHz Band PLL Tuned UHF Transmitter for Data Transfer Applications, Rev. 1.7 Freescale Semiconductor 13 Complete Application Schematic and PCB for OOK Modulation Figure 11 shows the output power versus the Rext resistor value with 50 Ω load and with matching network. Output power measurement in typical conditions (434MHz - Vcc=3V - 25°C) REXT SPECIFIED RANGE 8 6 Output power when matched (dBm) -0.35dB/kΩ Ω # -0.35mA/kΩ Ω 4 2 RFOUT Level (dBm) 0 -2 Output power on 50Ω Ω load (dBm) -4 -6 6 9 12 15 Rext (kΩ Ω) 18 21 24 Figure 11. Output Power at 434 MHz Band vs Rext Value The 50 Ω matching network used for the 868 MHz band is similar to the 434 MHz, excepting components values: L1 is changed to 8.2 nH and C3 to 470 pF in Figure 11. The typical gain of this 868 MHz matching network is 4 dB compared to unmatched configuration. 12 Complete Application Schematic and PCB for OOK Modulation Figure 12 shows a complete application schematic using a MC68HC908RK2 microcontroller. OOK modulation is selected, fcarrier = 433.92 MHz. The C2 to C5 capacitors can be removed if switch debounce is done by software. PLL Tuned UHF Transmitter for Data Transfer Applications, Rev. 1.7 14 Freescale Semiconductor Complete Application Schematic and PCB for OOK Modulation Vbat SW1 SW1a SW2a SW2 Vbat LED1 1 B1 C2 C3 C4 C5 2.2nF 2.2nF 2.2nF 2.2nF 2 R1 750 Vbat U1 1 2 3 U2 1 2 3 4 5 6 7 8 9 10 PTA0 20 PTA1/KBD1 PTB0/MCLK PTA2/KBD2 PTB1 PTA3/KBD3 PTB2/TCH0 PTA4/KBD4 PTB4/TCH1 PTA5/KBD5 PTB5 PTA6/KBD6 PTB3/TCLK 5 19 RST OSC2 IRQ1 VSS VDD MC68HC908RK2 Y1 6 13.56MHz 18 7 17 R2 16 MODE DATA ENABLE BAND VCC GND GNDRF XTAL1 RFOUT XTAL0 VCC REXT CFSK C7 22nF 13 12 11 10 C9 2.2pF 9 8 MC33493 C8 12K 100pF 15 PTA7 OSC1 4 C6 8.2pF DATACLK 14 14 13 12 11 Vbat C10 100nF Figure 12. Application Schematic for OOK Modulation, 434 MHz Frequency Band For 868 MHz band application, the input pin BAND must be wired to ground. See component description on Table 6 and Table 7. Table 6. External Components Description for OOK Component Function Value Unit Y1 Crystal, see Table 7 R2 RF output level setting resistor (Rext) Crystal load capacitor Power supply decoupling capacitors 315 MHz band: 9.84 434 MHz band: 13.56 868 MHz band: 13.56 12 MHz MHz MHz kΩ 8.21 22 100 pF nF pF C6 C7 C8 1 C6 value equals recommended crystal load capacitance reduced by the PCB stray capacitances. Examples of crystal reference are given below (see characteristics in Table 7) for different application bands: • • at 315 MHz band (freference = 9.84375 MHz, –40 °C < TA < 85 °C): NDK LN-G102-950, at 434/868 MHz bands (freference = 13.56 MHz, –40 °C < TA < 125 °C): NDK NX8045GB/CSJ S1-40125-8050-12 and NDK NX1255GA. PLL Tuned UHF Transmitter for Data Transfer Applications, Rev. 1.7 Freescale Semiconductor 15 Complete Application Schematic and PCB for FSK Modulation ) Table 7. Typical Crystal Characteristics (SMD Package) NDK NX8045GB/CSJ NDK NX1255GA S1-40125-8050-12 (for 434 MHz and 868 MHz) (for 434 MHz and 868 MHz) Parameter NDK LN-G102-950 (for 315 MHz) Load capacitance 12 12 12 pF Motional capacitance 3.33 4.4 10.5 fF Static capacitance 1.05 1.5 2.46 pF Loss resistance 28 18.5 10 Ω Unit Figure 13 shows a two-button keyfob board. Size is 30 × 45 millimeters. Figure 13. Two-Button Keyfob Board Layout 13 Complete Application Schematic and PCB for FSK Modulation Figure 14 shows a complete application schematic using a MC68HC908RK2 microcontroller. FSK modulation is selected, fcarrier= 433.92 MHz. C1 capacitor can be removed if switch debounce is done by software. PLL Tuned UHF Transmitter for Data Transfer Applications, Rev. 1.7 16 Freescale Semiconductor Complete Application Schematic and PCB for FSK Modulation Figure 14. Application Schematic for FSK Modulation, Serial Configuration, 434 MHz Frequency Band For 868 MHz band application, the input pin BAND must be wired to ground. See component description in Table 8. Table 8. External Components Description for FSK Component Function Value Unit Y1 Crystal 315 MHz band: 9.84, See Table 7 MHz 434 MHz band: 13.56, see Table 7 MHz 868 MHz band: 13.56, see Table 7 MHz R1 RF output level setting resistor (Rext) 12 kΩ C3 Crystal load capacitor See Table 9 pF C4 C2 pF Power supply decoupling capacitor C6 22 nF 100 pF Figure 15 shows the corresponding PCB layout. PLL Tuned UHF Transmitter for Data Transfer Applications, Rev. 1.7 Freescale Semiconductor 17 Recommendations for FSK Modulation Figure 15. Application PCB Layout for FSK Modulation, Serial Configuration, 434 MHz Frequency Band Table 9 gives the measured FSK deviations respective to C3 and C4 capacitor values for three deviations. Crystal reference is NDK NX8045GB/CSJ S1-40125-8050-12. Table 9. Crystal Pulling Capacitor Values vs Carrier Frequency Total Deviation -1Carrier frequency (MHz) Carrier frequency total deviation (kHz) C3 capacitor (pF) C4 capacitor (pF) Recommended R_off value (kΩ) 434 45 4.7 6.8 10 70 2.2 10 — 100 1 15 22 90 4.7 6.8 10 140 2.2 10 — 200 1 15 22 868 Another crystal reference, NDK NX1255GA (see Table 7), is enabled to reach higher deviation as mentioned on Table 10. These results are due to the higher crystal motional capacitor. Table 10. Crystal Pulling Capacitor Values vs Carrier Frequency Total Deviation -2- 14 Carrier frequency (MHz) Carrier frequency total deviation (kHz) C3 capacitor value (pF) C4 capacitor value (pF) Recommended R_off value (kΩ) 434 150 1 27 — 868 300 1 27 — Recommendations for FSK Modulation FSK deviation is function of total load capacitance presented to the crystal. This load capacitance is constituted by various contributors: • • • • the crystal characteristic, especially its static capacitance the external load capacitors (C3, C4 as defined in Figure 14 and Table 9) the device internal capacitance of pins XTAL0, XTAL1, CFSK the PCB track capacitance The schematic given in Figure 16 shows a typical FSK application using serial capacitor configuration, where device pads and PCB track capacitances are mentioned. PLL Tuned UHF Transmitter for Data Transfer Applications, Rev. 1.7 18 Freescale Semiconductor Recommendations for FSK Modulation Device pad capacitance is defined by the package capacitance and by the internal circuitry. Typical capacitance values for these pads are given in Table 11. Some realistic assumptions and measurements have been made concerning track parasitic capacitances for a 0.8 mm FR4 double side application PCB. They are given in Table 11 and the corresponding PCB layout is shown in figure Figure 17. To achieve large deviations, this total load capacitance must be lowered. For a given crystal, the PCB must be carefully laid out to reduce the capacitance of the tracks wired to XTAL0, XTAL1, and CFSK pins. Recommendation: a R_off resistor can be added in parallel with the FSK switch to optimize the transient response of demodulated signal. Table 11 gives the optimized R_off values for two deviations. There is no footprint for R_off resistor on the layout in Figure 16. When used, this component can be soldered on top of C3. Figure 16. Crystal Load Capacitance Contributors Schematic Table 11. Pads and Tracks Parasitic Values Capacitance Value Unit C_pad_XTAL0 1 pF C_pad_XTAL1 1 pF C_pad_CFSK 1 pF C_track_XTAL0 1.5 pF C_track_XTAL1 1.5 pF C_track_CFSK 1.5 pF PLL Tuned UHF Transmitter for Data Transfer Applications, Rev. 1.7 Freescale Semiconductor 19 Case Outline Dimensions 15 Case Outline Dimensions 14X K REF NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE 0.10 (0.004)M T U S V S 0.15 (0.006)T U S N 2X L/2 14 0.25 (0.010) 8 M B -U- L PIN 1 IDENT. N F 7 1 0.15 (0.006)T U S DETAIL E K A -V- K1 J J1 SECTION N-N -W- C 0.10 (0.004) -T- SEATING D PLANE G H DIM A B C D F G H J J1 K K1 L M MILLIMETERS MIN MAX 4.90 5.10 4.30 4.50 --1.20 0.05 0.15 0.50 0.75 0.65 BSC 0.50 0.60 0.09 0.20 0.09 0.16 0.19 0.30 0.19 0.25 6.40 BSC 0° 8° INCHES MIN MAX 0.193 0.200 0.169 0.177 --- 0.047 0.002 0.006 0.020 0.030 0.026 BSC 0.020 0.024 0.004 0.008 0.004 0.006 0.007 0.012 0.007 0.010 0.252 BSC 0° 8° DETAIL E CASE 948G-01 ISSUE O Figure 17. Case Outline Dimensions PLL Tuned UHF Transmitter for Data Transfer Applications, Rev. 1.7 20 Freescale Semiconductor THIS PAGE INTENTIONALLY BLANK PLL Tuned UHF Transmitter for Data Transfer Applications, Rev. 1.7 Freescale Semiconductor 21 How to Reach Us: Home Page: www.freescale.com Web Support: http://www.freescale.com/support USA/Europe or Locations Not Listed: Freescale Semiconductor, Inc. Technical Information Center, EL516 2100 East Elliot Road Tempe, Arizona 85284 +1-800-521-6274 or +1-480-768-2130 www.freescale.com/support Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) www.freescale.com/support Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku, Tokyo 153-0064 Japan 0120 191014 or +81 3 5437 9125 support.japan@freescale.com Asia/Pacific: Freescale Semiconductor Hong Kong Ltd. Technical Information Center 2 Dai King Street Tai Po Industrial Estate Tai Po, N.T., Hong Kong +800 2666 8080 support.asia@freescale.com For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 1-800-441-2447 or 303-675-2140 Fax: 303-675-2150 LDCForFreescaleSemiconductor@hibbertgroup.com Document Number: MC33493 Rev. 1.7 03/2007 Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”, must be validated for each customer application by customer’s technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. RoHS-compliant and/or Pb-free versions of Freescale products have the functionality and electrical characteristics as their non-RoHS-compliant and/or non-Pb-free counterparts. For further information, see http://www.freescale.com or contact your Freescale sales representative. For information on Freescale’s Environmental Products program, go to http://www.freescale.com/epp. Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. The Power Architecture and Power.org word marks and the Power and Power.org logos and related marks are trademarks and service marks licensed by Power.org © Freescale Semiconductor, Inc. 2007. All rights reserved.
MC33493DTBER2 价格&库存

很抱歉,暂时无法提供与“MC33493DTBER2”相匹配的价格&库存,您可以联系我们找货

免费人工找货